aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/usb/host
AgeCommit message (Collapse)AuthorFilesLines
2016-01-24usb: host: ehci-msm: Fix register initializationJack Pham1-0/+2
The default value for the 'transceiver select' field of the PORTSC register may not always be correct. Previously the phy-msm-usb driver would do this for us, but since ehci-msm can now be instantiated standalone without any PHY driver, the register needs to be explicitly initialized to ULPI mode to properly communicate with the PHY. This is not readily apparent, as firmware or bootloader code also happen to pre-initialize this for us. However, it can manifest when performing a driver unbind/rebind as follows: cd /sys/bus/platform/drivers/msm_hsusb_host echo QCOM8040:00 > unbind echo QCOM8040:00 > bind The EHCI core executes a controller reset as part of this, and as a result the register in question would revert to its default state and must be re-initialized properly. Furthermore this may be useful in the future when adding PM suspend/resume support. Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24usb: host: ehci-msm: Add support for ACPI probingJack Pham1-0/+8
Allow the EHCI MSM driver to probe against an ACPI enumerated device with ID QCOM8040. Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24usb: host: ehci-msm: Remove dependency on OTG PHYJack Pham1-22/+31
Currently the EHCI MSM driver has a hard dependency to be created by an OTG layer, namely the phy-msm-usb driver. In some cases or board configurations we want to allow the EHCI host to be instantiated without OTG capability. Instead, relax the dependency on having an OTG PHY being present and call usb_add_hcd() directly. Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Timur Tabi <timur@codeaurora.org> Reviewed-by: Andy Gross <andy.gross@linaro.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24usb: host: ehci-msm: Allow LS devices to workJack Pham1-0/+2
Disable the silicon quirk which is normally enabled for HSIC host mode. This would otherwise prevent low speed devices from enumerating properly. Signed-off-by: Jack Pham <jackp@codeaurora.org> Signed-off-by: Timur Tabi <timur@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24USB: bcma: separate code initializing USB 2.0 coreRafał Miłecki1-20/+39
This splits one big probing function into two smaller ones. The main one is now responsible for the generic stuff: allocating memory & enabling power using GPIO. The new one contains code that is specific to the USB 2.0 bcma core. This will allow adding support for the USB 3.0 bcma core (handling XHCI) in the future. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24USB: bcma: make helper creating platform dev more genericRafał Miłecki1-11/+13
Having "bool ohci" argument in bcma_hcd_create_pdev function limited it to support two cases only (OHCI and EHCI) and put too much logic in it. Lets make caller pass all required data. This adds few extra arguments to the function call but will allow us to reuse this code and handle more cases in the future (e.g. add XHCI support). Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24drivers/usb/host/fsl: Port USB EHCI host driver for LS102xASriram Dash1-10/+14
Change Power architecture specific APIs such as in_be32/out_be32 for registers read/write. Instead using ioread/writebe32 which are defined for power as well as arm architecture Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com> Signed-off-by: Sriram Dash <sriram.dash@freescale.com> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24drivers/usb/host: fsl: Set DMA_MASK of usb platform deviceSriram Dash1-1/+6
Set DMA_MASK of usb platform device properly. Signed-off-by: Sriram Dash <sriram.dash@freescale.com> Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-24usb: ohci: nxp: clean up included header filesVladimir Zapolskiy1-7/+0
Remove mach/irq.h from the list of included headers, there is no compilation dependency on this include file, the change is needed to prevent a compilation failure, when mach/irq.h is removed. Additionally remove other unneeded includes. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-01-22Merge tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-socLinus Torvalds1-0/+2
Pull ARM SoC support for Tegra platforms from Olof Johansson: "Here's a single-SoC topic branch that we've staged separately. Mainly because it was hard to sort the branch contents in a way that fit our existing branches due to some refactorings. The code has been in -next for quite a while, but we staged it in arm-soc a bit late, which is why we've kept it separate from the other updates and are sending it separately here" * tag 'armsoc-tegra' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: arm64: tegra: Add NVIDIA Jetson TX1 Developer Kit support arm64: tegra: Add NVIDIA P2597 I/O board support arm64: tegra: Add NVIDIA Jetson TX1 support arm64: tegra: Add NVIDIA P2571 board support arm64: tegra: Add NVIDIA P2371 board support arm64: tegra: Add NVIDIA P2595 I/O board support arm64: tegra: Add NVIDIA P2530 main board support arm64: tegra: Add Tegra210 support arm64: tegra: Add NVIDIA Tegra132 Norrin support arm64: tegra: Add Tegra132 support ARM: tegra: select USB_ULPI from EHCI rather than platform ARM: tegra: Ensure entire dcache is flushed on entering LP0/1 amba: Hide TEGRA_AHB symbol soc/tegra: Add Tegra210 support soc/tegra: Provide per-SoC Kconfig symbols
2016-01-15Merge tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linuxLinus Torvalds4-5/+5
Pull powerpc updates from Michael Ellerman: "Core: - Ground work for the new Power9 MMU from Aneesh Kumar K.V - Optimise FP/VMX/VSX context switching from Anton Blanchard Misc: - Various cleanups from Krzysztof Kozlowski, John Ogness, Rashmica Gupta, Russell Currey, Gavin Shan, Daniel Axtens, Michael Neuling, Andrew Donnellan - Allow wrapper to work on non-english system from Laurent Vivier - Add rN aliases to the pt_regs_offset table from Rashmica Gupta - Fix module autoload for rackmeter & axonram drivers from Luis de Bethencourt - Include KVM guest test in all interrupt vectors from Paul Mackerras - Fix DSCR inheritance over fork() from Anton Blanchard - Make value-returning atomics & {cmp}xchg* & their atomic_ versions fully ordered from Boqun Feng - Print MSR TM bits in oops messages from Michael Neuling - Add TM signal return & invalid stack selftests from Michael Neuling - Limit EPOW reset event warnings from Vipin K Parashar - Remove the Cell QPACE code from Rashmica Gupta - Append linux_banner to exception information in xmon from Rashmica Gupta - Add selftest to check if VSRs are corrupted from Rashmica Gupta - Remove broken GregorianDay() from Daniel Axtens - Import Anton's context_switch2 benchmark into selftests from Michael Ellerman - Add selftest script to test HMI functionality from Daniel Axtens - Remove obsolete OPAL v2 support from Stewart Smith - Make enter_rtas() private from Michael Ellerman - PPR exception cleanups from Michael Ellerman - Add page soft dirty tracking from Laurent Dufour - Add support for Nvlink NPUs from Alistair Popple - Add support for kexec on 476fpe from Alistair Popple - Enable kernel CPU dlpar from sysfs from Nathan Fontenot - Copy only required pieces of the mm_context_t to the paca from Michael Neuling - Add a kmsg_dumper that flushes OPAL console output on panic from Russell Currey - Implement save_stack_trace_regs() to enable kprobe stack tracing from Steven Rostedt - Add HWCAP bits for Power9 from Michael Ellerman - Fix _PAGE_PTE breaking swapoff from Aneesh Kumar K.V - Fix _PAGE_SWP_SOFT_DIRTY breaking swapoff from Hugh Dickins - scripts/recordmcount.pl: support data in text section on powerpc from Ulrich Weigand - Handle R_PPC64_ENTRY relocations in modules from Ulrich Weigand cxl: - cxl: Fix possible idr warning when contexts are released from Vaibhav Jain - cxl: use correct operator when writing pcie config space values from Andrew Donnellan - cxl: Fix DSI misses when the context owning task exits from Vaibhav Jain - cxl: fix build for GCC 4.6.x from Brian Norris - cxl: use -Werror only with CONFIG_PPC_WERROR from Brian Norris - cxl: Enable PCI device ID for future IBM CXL adapter from Uma Krishnan Freescale: - Freescale updates from Scott: Highlights include moving QE code out of arch/powerpc (to be shared with arm), device tree updates, and minor fixes" * tag 'powerpc-4.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (149 commits) powerpc/module: Handle R_PPC64_ENTRY relocations scripts/recordmcount.pl: support data in text section on powerpc powerpc/powernv: Fix OPAL_CONSOLE_FLUSH prototype and usages powerpc/mm: fix _PAGE_SWP_SOFT_DIRTY breaking swapoff powerpc/mm: Fix _PAGE_PTE breaking swapoff cxl: Enable PCI device ID for future IBM CXL adapter cxl: use -Werror only with CONFIG_PPC_WERROR cxl: fix build for GCC 4.6.x powerpc: Add HWCAP bits for Power9 powerpc/powernv: Reserve PE#0 on NPU powerpc/powernv: Change NPU PE# assignment powerpc/powernv: Fix update of NVLink DMA mask powerpc/powernv: Remove misleading comment in pci.c powerpc: Implement save_stack_trace_regs() to enable kprobe stack tracing powerpc: Fix build break due to paca mm_context_t changes cxl: Fix DSI misses when the context owning task exits MAINTAINERS: Update Scott Wood's e-mail address powerpc/powernv: Fix minor off-by-one error in opal_mce_check_early_recovery() powerpc: Fix style of self-test config prompts powerpc/powernv: Only delay opal_rtc_read() retry when necessary ...
2016-01-13Merge tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds31-222/+1644
Pull USB updates from Greg KH: "Here is the big USB drivers update for 4.5-rc1. Lots of gadget driver updates and fixes, like usual, and a mix of other USB driver updates as well. Full details in the shortlog. All of these have been in linux-next for a while" * tag 'usb-4.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (191 commits) MAINTAINERS: change my email address USB: usbmon: remove assignment from IS_ERR argument USB: mxu11x0: drop redundant function name from error messages USB: mxu11x0: fix debug-message typos USB: mxu11x0: rename usb-serial driver USB: mxu11x0: fix modem-control handling on B0-transitions USB: mxu11x0: fix memory leak on firmware download USB: mxu11x0: fix memory leak in port-probe error path USB: serial: add Moxa UPORT 11x0 driver USB: cp210x: add ID for ELV Marble Sound Board 1 usb: chipidea: otg: use usb autosuspend to suspend bus for HNP usb: chipidea: host: set host to be null after hcd is freed usb: chipidea: removing of_find_property usb: chipidea: implement platform shutdown callback usb: chipidea: clean up CONFIG_USB_CHIPIDEA_DEBUG reference usb: chipidea: delete static debug support usb: chipidea: support debugfs without CONFIG_USB_CHIPIDEA_DEBUG usb: chipidea: udc: improve error handling on _hardware_enqueue usb: chipidea: udc: _ep_queue and _hw_queue cleanup usb: dwc3: of-simple: fix build warning on !PM ...
2016-01-12Merge tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into late/tegraOlof Johansson1-0/+2
ARM: tegra: Core SoC changes for v4.5-rc1 The big thing here is Tegra210 support, which is really only the Kconfig symbol. Other than that there's a few miscellaneous fixes. * tag 'tegra-for-4.5-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: ARM: tegra: select USB_ULPI from EHCI rather than platform ARM: tegra: Ensure entire dcache is flushed on entering LP0/1 amba: Hide TEGRA_AHB symbol soc/tegra: Add Tegra210 support soc/tegra: Provide per-SoC Kconfig symbols Signed-off-by: Olof Johansson <olof@lixom.net>
2016-01-04Merge branch 'memdup_user_nul' into work.miscAl Viro6-14/+67
2015-12-23new helpers: no_seek_end_llseek{,_size}()Al Viro1-21/+2
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2015-12-22QE: Move QE from arch/powerpc to drivers/socZhao Qiang4-5/+5
ls1 has qe and ls1 has arm cpu. move qe from arch/powerpc to drivers/soc/fsl to adapt to powerpc and arm Signed-off-by: Zhao Qiang <qiang.zhao@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com>
2015-12-13Merge 4.4-rc5 into usb-next as we want those fixes here for testingGreg Kroah-Hartman6-14/+67
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-11xhci: fix usb2 resume timing and races.Mathias Nyman2-6/+44
According to USB 2 specs ports need to signal resume for at least 20ms, in practice even longer, before moving to U0 state. Both host and devices can initiate resume. On device initiated resume, a port status interrupt with the port in resume state in issued. The interrupt handler tags a resume_done[port] timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer. Root hub timer requests for port status, finds the port in resume state, checks if resume_done[port] timestamp passed, and set port to U0 state. On host initiated resume, current code sets the port to resume state, sleep 20ms, and finally sets the port to U0 state. This should also be changed to work in a similar way as the device initiated resume, with timestamp tagging, but that is not yet tested and will be a separate fix later. There are a few issues with this approach 1. A host initiated resume will also generate a resume event. The event handler will find the port in resume state, believe it's a device initiated resume, and act accordingly. 2. A port status request might cut the resume signalling short if a get_port_status request is handled during the host resume signalling. The port will be found in resume state. The timestamp is not set leading to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0. get_port_status will proceed with moving the port to U0. 3. If an error, or anything else happens to the port during device initiated resume signalling it will leave all the device resume parameters hanging uncleared, preventing further suspend, returning -EBUSY, and cause the pm thread to busyloop trying to enter suspend. Fix this by using the existing resuming_ports bitfield to indicate that resume signalling timing is taken care of. Check if the resume_done[port] is set before using it for timestamp comparison, and also clear out any resume signalling related variables if port is not in U0 or Resume state This issue was discovered when a PM thread busylooped, trying to runtime suspend the xhci USB 2 roothub on a Dell XPS Cc: stable <stable@vger.kernel.org> Reported-by: Daniel J Blueman <daniel@quora.org> Tested-by: Daniel J Blueman <daniel@quora.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04usb: ehci: ohci: fix bool assignmentsGeyslan G. Bem3-4/+4
When assigning bool use true instead of 1. If declaring it as static and it's false there's no need to initialize it, since static variables are zeroed by default. Caught by coccinelle. Signed-off-by: Geyslan G. Bem <geyslan@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04xhci: refuse loading if nousb is usedOliver Neukum1-0/+4
The module should fail to load. Signed-off-by: Oliver Neukum <oneukum@suse.com> CC: stable@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04usb: use BUG_ON() instead of BUG()Geyslan G. Bem1-5/+3
Replace BUG() with BUG_ON(). Caught by coccinelle. Signed-off-by: Geyslan G. Bem <geyslan@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04usb: whci: fhci: remove comparison to boolGeyslan G. Bem2-2/+2
Get rid of bool explicit comparisons. Caught by Coccinelle. Signed-off-by: Geyslan G. Bem <geyslan@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04USB: host: ohci-at91: fix a crash in ohci_hcd_at91_overcurrent_irqAlexandre Belloni1-6/+5
The interrupt handler, ohci_hcd_at91_overcurrent_irq may be called right after registration. At that time, pdev->dev.platform_data is not yet set, leading to a NULL pointer dereference. Fixes: e4df92279fd9 (USB: host: ohci-at91: merge loops in ohci_hcd_at91_drv_probe) Reported-by: Peter Rosin <peda@axentia.se> Tested-by: Peter Rosin <peda@axentia.se> Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com> Cc: stable@vger.kernel.org # 4.3+ Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04usb: xhci: fix config fail of FS hub behind a HS hub with MTTChunfeng Yun1-0/+8
if a full speed hub connects to a high speed hub which supports MTT, the MTT field of its slot context will be set to 1 when xHCI driver setups an xHCI virtual device in xhci_setup_addressable_virt_dev(); once usb core fetch its hub descriptor, and need to update the xHC's internal data structures for the device, the HUB field of its slot context will be set to 1 too, meanwhile MTT is also set before, this will cause configure endpoint command fail, so in the case, we should clear MTT to 0 for full speed hub according to section 6.2.2 Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-04xhci: Fix memory leak in xhci_pme_acpi_rtd3_enable()Mika Westerberg1-2/+6
There is a memory leak because acpi_evaluate_dsm() actually returns an object which the caller is supposed to release. Fix this by calling ACPI_FREE() for the returned object (this expands to kfree() so passing NULL there is fine as well). While there correct indentation in !CONFIG_ACPI case. Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com> Cc: stable <stable@vger.kernel.org> # v4.2 Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: ehci-msm: Use posted data writes on AHBAndy Gross1-2/+2
This patch sets the AHBMODE to allow for posted data writes. This results in higher performance. Signed-off-by: Andy Gross <agross@codeaurora.org> Tested-by: Georgi Djakov <georgi.djakov@linaro.org> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01USB: bcma: switch to GPIO descriptor for power controlRafał Miłecki1-11/+10
So far we were using simple (legacy) GPIO functions & some poor logic to control power. It got many drawbacks: we were ignoring OF flags (GPIO_ACTIVE_LOW), we were not setting direction to output and we were assuming gpio_request success all the time. Fix it by switching to gpiod functions and adding appropriate checks. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Acked-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01USB: whci-hcd: add check for dma mapping errorAlexey Khoroshilov1-0/+4
qset_fill_page_list() do not check for dma mapping errors. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: ohci-pxa27x: use of_property_read_bool()Saurabh Sengar1-7/+7
for checking if a property is present or not, of_property_read_bool is more appropriate than of_get_property() Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01USB-EHCI: Delete unnecessary checks before the function call "dma_pool_destroy"Markus Elfring1-13/+5
The dma_pool_destroy() function tests whether its argument is NULL and then returns immediately. Thus the test around the calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb : replace dma_pool_alloc and memset with dma_pool_zallocSaurabh Sengar3-8/+4
replace dma_pool_alloc and memset with a single call to dma_pool_zalloc Signed-off-by: Saurabh Sengar <saurabh.truth@gmail.com> Acked-by: Peter Chen <peter.chen@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01xhci: rework xhci extended capability list parsing functionsMathias Nyman3-114/+61
Replace the existing two extended capability parsing helper functions with one called xhci_find_next_ext_cap(). The extended capabilities are read both in pci-quirks before xhci driver is loaded, and inside the xhci driver when adding ports. The existing helpers did not suit well for these cases and a lot of custom parsing code was needed. The new helper function simplifies these two cases a lot. The motivation for this rework was that code to support xhci debug capability needed to parse extended capabilities, and it included yet another capability parsing helper specific for its needs. With this solution it debug capability code can use this new helper as well Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01xhci: use debug level when printing out interval rounding messagesMathias Nyman1-1/+1
Don't use dev_warn() for intened behaviour, use dev_dbg() Rounding down the interval to the nearest power of 2 is required by xhci specs. Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01xhci: mediatek: support MTK xHCI host controllerChunfeng Yun8-6/+1383
There some vendor quirks for MTK xhci host controller: 1. It defines some extra SW scheduling parameters for HW to minimize the scheduling effort for synchronous and interrupt endpoints. The parameters are put into reseved DWs of slot context and endpoint context. 2. Its IMODI unit for Interrupter Moderation register is 8 times as much as that defined in xHCI spec. 3. Its TDS in Normal TRB defines a number of packets that remains to be transferred for a TD after processing all Max packets in all previous TRBs. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Tested-by: Daniel Thompson <daniel.thompson@linaro.org> Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: xhci-plat: add support for the R-Car H3 xHCI controllersYoshihiro Shimoda4-2/+21
The R-Car H3 has two xHCI controllers. This SoC is compatible with R-Car Gen2 SoCs, however this SoC doesn't need some specific registers setting, and need a new firmware. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: xhci-plat: add support for the R-Car M2-N xHCI controllerYoshihiro Shimoda1-0/+3
This patch adds support for R-Car M2-N (r8a7793) xHCI controller. This SoC is compatible with R-Car H2 (r8a7790) and R-Car M2-W (r8a7791). Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: xhci-rcar: Change code for new SoCsYoshihiro Shimoda3-14/+26
This patch changes code to ease the addition of next generation SoCs. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: xhci-plat: add firmware_name in xhci_plat_privYoshihiro Shimoda1-0/+1
This patch adds a member "firmware_name" in struct xhci_plat_priv to simplify the code to match specific firmware name. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: xhci-plat: add struct xhci_plat_privYoshihiro Shimoda2-25/+85
This patch adds struct xhci_plat_priv to simplify the code to match platform specific variables. For now, this patch adds a member "type" in the structure. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: xhci: add a platform-private fieldYoshihiro Shimoda1-0/+3
This patch adds an xhci->priv field for private use by XHCI platform drivers. Until now none of the platform drivers has used this private space. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01usb: host: xhci: cleanup hcd private sizeYoshihiro Shimoda3-3/+1
This patch cleanups the hcd private size to suitable size. The previous code has "sizeof(struct xhci_hcd *)" in xhci_hc_driver as hcd_priv_size and sizeof(struct xhci_hcd) in xhci_plat_overrides or xhci_pci_overrides as extra_priv_size. However, the xhci driver uses a "sizeof(struct xhcd_hcd)" memory space in each hcd (main_hcd and shared_hcd) actually. Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01xhci: use the correct define to indicate port status suspend change.Mathias Nyman1-1/+1
use the variables defined for populating the port status and port chage bits retuend by GetPortStatus request intead of the hub class feature selectors. The defines for hub class feature selectors are used for other purposes, they work as port status and feature selectors are in the same order, and set the same bits, but it makes the code very hard to follow Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01USB: EHCI: warn on unexpectedly active QHAlan Stern2-2/+8
This patch adds a new warning message to ehci-hcd. The warning is triggered whenever the driver finds that the hardware has set the Active bit in a QH at a time when the driver expects the QH to be completely idle. Such bugs have been observed by users in the past, and since they can lead to serious problems (such as inability to unlink an URB that never completes), it would be good to know about them when they occur. This won't fix these bugs; that's a bigger job for a later patch. But success isn't guaranteed, since this depends on aspects of the hardware which are not documented in the EHCI spec or for which the spec's recommendations are clearly unworkable. It therefore seems worthwhile to check for these bugs proactively. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Michael Reutman <mreutman@epiqsolutions.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-12-01USB: EHCI: enhance "async" debugfs outputAlan Stern1-4/+11
This patch enhances the "async" debugfs file in ehci-hcd by printing out several additional fields in the hardware-accessible data structures. These fields are important for determining the hardware's view of the async schedule, in particular, the addresses of the current and next qTDs for each QH along with the start address of each qTD's data buffer. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-24ARM: tegra: select USB_ULPI from EHCI rather than platformArnd Bergmann1-0/+2
For historic reasons, the tegra platform selects USB_ULPI from architecture code, but that hasn't really made sense for a long time, as the only user of that code is the Tegra EHCI driver that has its own Kconfig symbol. This removes the 'select' statements from mach-tegra and drivers/soc/tegra and adds them with the device driver that actually needs them. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-11-18xhci: Fix a race in usb2 LPM resume, blocking U3 for usb2 devicesMathias Nyman1-6/+9
Clear device initiated resume variables once device is fully up and running in U0 state. Resume needs to be signaled for 20ms for usb2 devices before they can be moved to U0 state. An interrupt is triggered if a device initiates resume. As we handle the event in interrupt context we can not sleep for 20ms, so we instead set a resume flag, a timestamp, and start the roothub polling. The roothub code will later move the port to U0 when it finds a port in resume state with the resume flag set, and timestamp passed by 20ms. A host initiated resume is however not done in interrupt context, and host initiated resume code will directly signal resume, wait 20ms and then move the port to U0. These two codepaths can race, if we are in the middle of a host initated resume, while sleeping for 20ms, we may handle a port event and find the port in resume state. The port event handling code will assume the resume was device initiated and set the resume flag and timestamp. Root hub code will however not catch the port in resume state again as the host initated resume code has already moved the port to U0. The resume flag and timestamp will remain set for this port preventing port from suspending again (LPM setting port to U3) Fix this for now by always clearing the device initated resume parameters once port is in U0 Cc: stable <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-18usb: xhci: fix checking ep busy for CFCLu Baolu1-26/+6
Function ep_ring_is_processing() checks the dequeue pointer in endpoint context to know whether an endpoint is busy with processing TRBs. This is not correct since dequeue pointer field in an endpoint context is only valid when the endpoint is in Halted or Stopped states. This buggy code causes audio noise when playing sound with USB headset connected to host controllers which support CFC (one of xhci 1.1 features). This patch should exist in stable kernel since v4.3. Reported-and-tested-by: YD Tseng <yd_tseng@asmedia.com.tw> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Cc: stable <stable@vger.kernel.org> # v4.3 Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-18xhci: Workaround to get Intel xHCI reset working more reliablyRajmohan Mani1-0/+10
Existing Intel xHCI controllers require a delay of 1 mS, after setting the CMD_RESET bit in command register, before accessing any HC registers. This allows the HC to complete the reset operation and be ready for HC register access. Without this delay, the subsequent HC register access, may result in a system hang, very rarely. Verified CherryView / Braswell platforms go through over 5000 warm reboot cycles (which was not possible without this patch), without any xHCI reset hang. Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com> Tested-by: Joe Lawrence <joe.lawrence@stratus.com> Cc: stable <stable@vger.kernel.org> Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-11-09dma: remove external references to dma_supportedChristoph Hellwig3-3/+3
Signed-off-by: Christoph Hellwig <hch@lst.de> Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2015-11-07Merge branch 'akpm' (patches from Andrew)Linus Torvalds1-1/+1
Merge second patch-bomb from Andrew Morton: - most of the rest of MM - procfs - lib/ updates - printk updates - bitops infrastructure tweaks - checkpatch updates - nilfs2 update - signals - various other misc bits: coredump, seqfile, kexec, pidns, zlib, ipc, dma-debug, dma-mapping, ... * emailed patches from Andrew Morton <akpm@linux-foundation.org>: (102 commits) ipc,msg: drop dst nil validation in copy_msg include/linux/zutil.h: fix usage example of zlib_adler32() panic: release stale console lock to always get the logbuf printed out dma-debug: check nents in dma_sync_sg* dma-mapping: tidy up dma_parms default handling pidns: fix set/getpriority and ioprio_set/get in PRIO_USER mode kexec: use file name as the output message prefix fs, seqfile: always allow oom killer seq_file: reuse string_escape_str() fs/seq_file: use seq_* helpers in seq_hex_dump() coredump: change zap_threads() and zap_process() to use for_each_thread() coredump: ensure all coredumping tasks have SIGNAL_GROUP_COREDUMP signal: remove jffs2_garbage_collect_thread()->allow_signal(SIGCONT) signal: introduce kernel_signal_stop() to fix jffs2_garbage_collect_thread() signal: turn dequeue_signal_lock() into kernel_dequeue_signal() signals: kill block_all_signals() and unblock_all_signals() nilfs2: fix gcc uninitialized-variable warnings in powerpc build nilfs2: fix gcc unused-but-set-variable warnings MAINTAINERS: nilfs2: add header file for tracing nilfs2: add tracepoints for analyzing reading and writing metadata files ...
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.