aboutsummaryrefslogtreecommitdiffstats
path: root/drivers/usb/mtu3 (follow)
AgeCommit message (Collapse)AuthorFilesLines
2017-08-22Merge tag 'usb-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-nextGreg Kroah-Hartman1-0/+1
Felipe writes: usb: changes for v4.14 merge window Not a big pull request this time around. Only 49 non-merge commits. This pull request is, however, all over the place. Most of the changes are in the bdc driver adding support for USB Phy layer and PM. Renesas adds support for R-Car H3 ES2.0 and R-Car M3-W SoCs. Also here is PM_RUNTIME support for dwc3-keystone. UDC Core got a DMA unmap fix to make sure we only unmap requests that were, indeed, mapped. Other than these, we have a lot of cleanups, many of them adding 'const' to several places.
2017-08-15usb: mtu3: add generic compatible stringChunfeng Yun1-0/+1
The mtu3 driver is a generic driver for MediaTek usb3 DRD IP, add a generic compatible to avoid confusion when support new SoCs but use a compatible with specific SoC's name "mt8173". Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-15usb: mtu3: fix ip sleep auto-exit issue when enable DRD modeChunfeng Yun1-1/+3
Ip sleep will auto exit if vbus comparison circuit of u2 phy is disabled when system tries to enter suspend mode, so get vbus-valid status from mac but not from u2 phy when enable DRD mode to fix the issue. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-15usb: mtu3: clear u1/u2_enable to 0 in mtu3_gadget_resetChunfeng Yun1-0/+2
when the device is reset by host, the status of u1_enable and u2_enable should also be restored to default value. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-15usb: mtu3: handle delayed status of the control transferChunfeng Yun3-3/+24
Add the delayed status handling. This is used by mass storage etc to gain some extra time to setup its internal status before it can proceed further requests, and once the gadget is ready, it will enqueue an empty packet which is used for synchronization. The issue may happen on some FGPA platform with very low cpu frequency. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-08-10usb: mtu3: add a vbus debugfs interfaceChunfeng Yun1-8/+50
Provides a new vbus debugfs interface used to turn on/off vbus regulator, it also can be used to get/put reference count of vbus, due to sometimes we need keep it alive when manually switch mtu3 to device mode. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-08-09usb: mtu3: add a vbus debugfs interfaceChunfeng Yun1-8/+50
Provides a new vbus debugfs interface used to turn on/off vbus regulator, it also can be used to get/put reference count of vbus, due to sometimes we need keep it alive when manually switch mtu3 to device mode. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-07-30usb: mtu3: fix ip sleep auto-exit issue when enable DRD modeChunfeng Yun1-1/+3
Ip sleep will auto exit if vbus comparison circuit of u2 phy is disabled when system tries to enter suspend mode, so get vbus-valid status from mac but not from u2 phy when enable DRD mode to fix the issue. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30usb: mtu3: clear u1/u2_enable to 0 in mtu3_gadget_resetChunfeng Yun1-0/+2
when the device is reset by host, the status of u1_enable and u2_enable should also be restored to default value. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-30usb: mtu3: handle delayed status of the control transferChunfeng Yun3-3/+24
Add the delayed status handling. This is used by mass storage etc to gain some extra time to setup its internal status before it can proceed further requests, and once the gadget is ready, it will enqueue an empty packet which is used for synchronization. The issue may happen on some FGPA platform with very low cpu frequency. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-07-22usb: Convert to using %pOF instead of full_nameRob Herring1-2/+2
Now that we have a custom printf format specifier, convert users of full_name to use %pOF instead. This is preparation to remove storing of the full path string for each node. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-06-13usb: mtu3: Handle return value of clk_prepare_enableArvind Yadav1-3/+20
clk_prepare_enable() can fail here and we must check its return value. Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-05-25usb: mtu3: cleanup with list_first_entry_or_null()Masahiro Yamada1-6/+2
The combo of list_empty() and list_first_entry() can be replaced with list_first_entry_or_null(). Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-04-11usb: mtu3: Replace the extcon APIChanwoo Choi1-13/+6
This patch uses the resource-managed extcon API for extcon_register_notifier() and replaces the deprecated extcon API as following: - extcon_get_cable_state_() -> extcon_get_state() Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Cc: Chunfeng Yun <chunfeng.yun@mediatek.com> Cc: linux-usb@vger.kernel.org Tested-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com> Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2017-02-09usb: mtu3: remove redundant dev_err call in get_ssusb_rscs()Wei Yongjun1-3/+1
There is a error message within devm_ioremap_resource already, so remove the dev_err call to avoid redundant error message. Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-08usb: mtu3: make the reference clock optionalChunfeng Yun1-2/+9
Make the reference clock optional for DTS backward compatibility and ignore the error if it does not exist. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-19usb: mtu3: add reference clockChunfeng Yun2-2/+20
usually, the reference clock comes from 26M oscillator directly, but some SoCs are not, add it for compatibility. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-01-19usb: mtu3: get resources that cause deferred probe earlierChunfeng Yun1-12/+12
Some resources such as regulator, clock usually cause deferred probe, get them earlier to avoid more ineffective processing. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-07usb: mtu3: fix U3 port link issueChunfeng Yun1-8/+10
the issue is introduced when @is_u3_ip is used in mtu3_device_enabe() before initialized in mtu3_mem_alloc(), so get global IP information at first before used by following functins. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-12-07usb: mtu3: enable auto switch from U3 to U2Chunfeng Yun1-0/+2
inform mac2 to build U2 link automatically after U3 detect fail without software setting soft_connect. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-11-14usb: mtu3: declare functions staticSudip Mukherjee2-2/+2
The only user of the functions mtu3_irq() and gpd_ring_empty() are in the same file. They can be declared as static. Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Acked-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27usb: mtu3: dual-role mode supportChunfeng Yun9-21/+557
support dual-role mode; there are two ways to switch between host and device modes, one is by idpin, another is by debugfs which depends on user input. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27usb: mtu3: host only mode supportChunfeng Yun7-80/+691
supports host only mode and the code is ported from host/xhci-mtk.c IPPC register shared between host and device is moved into common glue layer. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27usb: mtu3: Super-Speed Peripheral mode supportChunfeng Yun5-37/+346
add super-speed funtion for peripheral mode Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-10-27usb: Add MediaTek USB3 DRD driverChunfeng Yun10-0/+3857
This patch adds support for the MediaTek USB3 controller integrated into MT8173. It currently supports High-Speed Peripheral Only mode. Super-Speed Peripheral, Dual-Role Device and Host Only (xHCI) modes will be added in the next patchs. Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.