| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Felipe writes:
usb: generic resume timeout for v4.1
This part 2 pull request contains only the patches
which make sure everybody on linux uses the same
resume timeout value.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Make sure we're using the new macro, so our
resume signaling will always pass certification.
Based on original work by Bin Liu <Bin Liu <b-liu@ti.com>>
Cc: Bin Liu <b-liu@ti.com>
Cc: <stable@vger.kernel.org> # v3.10+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Commit 3e457371f436 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
fixed a USB error on dm816x, but introduced a new build error on i386
when COMPILE_TEST is set:
drivers/usb/musb/musb_dsps.c: In function ‘dsps_read_fifo32’:
drivers/usb/musb/musb_dsps.c:624:3: error: implicit declaration of function
‘readsl’ [-Werror=implicit-function-declaration]
readsl(fifo, dst, len >> 2);
Let's fix this by using ioread32_rep() instead of readsl() as that's
more portable.
Fixes: 3e457371f436 ("usb: musb: Fix fifo reads for dm816x with musb_dsps")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix using the bare number to set the 'bDescriptorType' field of the Hub
Descriptor while the value is #define'd in <linux/usb/ch11.h>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Felipe writes:
usb: patches for v4.1 merge window
As usual, a big pile of commits. This time a total
of 111 non-merge commits.
Other than the usual set of cleanups and non-critical
fixes, we have some interesting work for AM335x's MUSB
babble recovery. Now that takes a lot less time and we
don't have to Reset MUSB all the time.
The printer gadget has been converted to configfs interface
and the atmel udc has learned suspend/resume with wakeup.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Looks like dm81xx can only do 32-bit fifo reads like am35x. Let's set
up musb-dsps with a custom read_fifo function based on the compatible
flag.
Otherwise we can get the following errors when starting dhclient on a
asix USB Ethernet adapter:
asix 2-1:1.0 eth2: asix_rx_fixup() Bad Header Length 0xffff003c, offset 4
While at it, let's also remove pointless cast of the driver data.
Cc: Bin Liu <binmlist@gmail.com>
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Cc: George Cherian <george.cherian@ti.com>
Cc: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
connect AR9271(USB wifi) to AM335x, and send a flood ping from Mac OSX,
AR9271 is stopped.
on USB bus, the following occurs.
- OUT transaction is ACKed (NYET).
- IN transaction is ACKed (512bytes).
- PING-NAK transaction is continued for about 2 seconds (AR9271 timeout?).
In current imprementation, IN-transaction is not completed because it
checks the empty of TX-FIFO in cppi41_dma_callback().
As a result, communication to AR9271 stops.
This patch modified to check the empty of TX-FIFO only when OUT-transaction.
Signed-off-by: Takeyoshi Kikuchi <kikuchi@centurysys.co.jp>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If we pass our own of_node to musb_core, at least
pinctrl settings will be duplicated, meaning that
pinctrl framework will try to select default pin
state for musb_core when they were already requested
by musb-dsps.
A Warning will be printed however things will still
work.
Reported-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
musb shouldn't have of_node and phy phandle is passed
to dsps device, not musb's.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
there's no need to fake an IRQ, just check
if VBUS is valid already.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
when polling, we were using n * HZ (where n is
an integer in seconds), however HZ isn't always
correct if we're using cpufreq. A better way
is to use msecs_to_jiffies(n) (where n is now
an integer in miliseconds).
while at that, also rename poll_seconds to poll_timeout
and change its type to unsigned int.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
according to comment in code, HS completion
will happen pretty fast, instead of using
udelay(), let's just busy loop and drop a
cpu_relax() where udelay() was.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
as soon as we find out tx fifo is empty, there's
no need to break out of the loop just to have another
branch to complete the transfer. We can just complete
transfer and exit early.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
no functional changes, clean up only.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
we can also have babble conditions with LS/FS
and we also want to recover in that case.
Because of that we will drop the check of HSMODE
and always try to run babble recovery.
Suggested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There's no point is splitting those anymore.
We're now also able to drop another forward
declaration.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
no functional changes, cleanup only.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
that's not needed anymore. Everything that we
call is irq-safe, so we might as well not
have a delayed work for babble recovery.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
recover is a much better name than reset, considering
we don't really reset the IP, just run platform-specific
babble recovery algorithm.
while at that, also fix a typo in comment and add kdoc
for recover memeber of platform_ops.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
we're not resetting musb at all, just restarting
the session. This means we don't need to touch PHYs
or VBUS or anything like that. Just make sure session
bit is reenabled after MUSB dropped it.
while at that, make sure to tell usbcore that we're
dropping the session and, thus, disconnecting the
device.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
All we have to do is, really, drop session bit
and let the session restart.
Big thanks goes to Bin Liu <b-liu@ti.com> for
inspiring this work.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When babble IRQ happens, we need to wait only
5.3us (320 cycles of 60MHz clock), we will give
it some slack and schedule our work a 10 usecs into
the future.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We do *not* want to touch devctl at all when
trying to recover from babble. All we want to
do is mask IRQs until we're done without our
babble recovery, at which point we will unmask
IRQs.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
sometimes we want to just mask/unmask interrupts
without touching devctl register. For those
cases, let's introduce musb_enable_interrupts and
musb_disable_interrupts()
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this makes it easier to filter function traces.
No functional changes.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Whenever babble happens, MUSB controller will
drop session automatically.
The only case where it won't drop the session,
is when we're running on AM335x and SW_SESSION_CTRL
bit has been set. In that case, controller will
not touch session bit so SW has a chance to recover
from babble condition.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We want to check if that particular bit is
set. It could very well be that bootloader
(or romcode) has fiddled with MUSB before
us which could leave other bits set in this
register.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
musb->int_usb already contains the correct
information for musb-core to handle babble.
In fact, this very check was just causing a
nonsensical babble interrupt storm.
With this I can get test.sh to run and, even though
all tests fail with timeout, that's still better
than locking up the system due to IRQ storm.
Also, if I remove g_zero and load g_mass_storage,
then everything works fine again.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
MUSB does not generate a connect IRQ when working
in peripheral mode.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
when musb is operating as host and a remote wakeup
fires up, a resume interrupt will be raised. At that
point SUSPENDM bit is automatically cleared and
RESUME bit is automatically set.
Remove those two from IRQ handler.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
no functional changes, clean up only.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There was already a proper place where we were
checking for babble interrupts, move babble
recovery there.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
if reset fails, we should return a *negative*
error code, not a positive value.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
FSDEV is set for both HIGH and FULL speeds,
the correct HIGHSPEED check is done through
power register's HSMODE bit.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
no functional changes, clean up only.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
devctl & MUSB_DEVCTL_HM represents a single bit,
just check for the bit, there's really no need
to compare the result against 0.
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
A recent bug fix I did that was marked for stable backports
introduced a slightly wrong dependency on CONFIG_OMAP_CONTROL_PHY.
I was missing the fact that the PHY driver already stubs out the
omap_control_usb_set_mode, and we only need to add a dependency
to prevent the musb-omap2430 driver from being built-in when
the phy driver is a loadable module, but we should not prevent it
from being built altogether when the phy driver is disabled.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca784be36cc725 ("usb: start using the control module driver")
Cc: <stable@vger.kernel.org> # v3.9+
Acked-by: Acked-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
instead of using manually spelled out bit-shits
and iterate over each of the 16-bits (one for
each endpoint) on each direction, we can make use
of for_each_set_bit() which internally uses
find_first_bit().
This makes the code slightly more readable while
also making we only iterate over bits which are
actually set.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
As per Mentor Graphics' documentation, we should
always handle TX endpoints before RX endpoints.
This patch fixes that error while also updating
some hard-to-read comments which were scattered
around musb_interrupt().
This patch should be backported as far back as
possible since this error has been in the driver
since it's conception.
Cc: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
that function is pretty close to a no-op by now,
all we need is a call to musb_stop().
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We still have a combination of legacy phys and generic phys in
use so we need to support both types of phy for musb_dsps.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The value for the multipoint dts property is ignored when parsing with
of_property_read_bool, so we currently have multipoint always set as 1
even if value 0 is specified in the dts file.
Let's fix this to read the value too instead of just the property like
the binding documentation says as otherwise MUSB will fail to work
on devices with Mentor configuration that does not support multipoint.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We need a pm_runtime_get_sync() call from
within musb_gadget_pullup() to make sure
registers are accessible at that time.
The problem is that musb_gadget_pullup() is
called with IRQs disabled and, because of that,
we need to tell pm_runtime that this pm_runtime_get_sync()
is IRQ safe.
We can simply add pm_runtime_irq_safe(), however, because
we need to make our read/write accessor function pointers
have been initialized before trying to use them. This means
that all pm_runtime initialization for musb_core needs to
be moved down so that when we call pm_runtime_irq_safe(),
the pm_runtime_get_sync() that it calls on the parent, won't
cause a crash due to NULL musb_read/write accessors.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Enable HCD_BH flag for musb host controller driver.
This improves the MSC/UVC through put. With this enabled
even 640x480@30fps webcam streaming is also supported.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The commit 889ad3b "usb: musb: try a race-free wakeup" breaks device
hotplug enumeraitonn when the device is connected behind a hub while usb
autosuspend is enabled.
Adding finish_resume_work into runtime resume callback fixes the issue.
Also resume root hub is required to resume the bus from runtime suspend,
so move musb_host_resume_root_hub() back to its original location, where
handles RESUME interrupt.
Signed-off-by: Bin Liu <b-liu@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
bfin_remove() is not (nor should it be) marked as __exit, so we should
not be using __exit_p() wrapper with it, otherwise unbinding through
sysfs does not work properly.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The omap musb front-end calls into the phy driver directly
instead of using a generic phy interface, which causes a link
error when the specific driver is not built-in:
drivers/built-in.o: In function `omap2430_musb_disable':
usb/musb/omap2430.c:480: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap2430_musb_enable':
usb/musb/omap2430.c:466: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:447: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o: In function `omap_musb_set_mailbox':
usb/musb/omap2430.c:273: undefined reference to `omap_control_usb_set_mode'
usb/musb/omap2430.c:304: undefined reference to `omap_control_usb_set_mode'
drivers/built-in.o:(.debug_addr+0xbd9e0): more undefined references to `omap_control_usb_set_mode' follow
This adds an explicit dependency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: ca784be36cc725 ("usb: start using the control module driver")
Cc: <stable@vger.kernel.org> # v3.9+
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Multiple musb glue drivers depend on the generic usb phy support,
but fail to list it as a dependency in Kconfig. This results
in build erros like:
drivers/built-in.o: In function `am35x_remove':
:(.text+0xadacc): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `am35x_probe':
:(.text+0xae1c8): undefined reference to `usb_phy_generic_register'
:(.text+0xae244): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_remove':
:(.text+0xaf648): undefined reference to `usb_phy_generic_unregister'
drivers/built-in.o: In function `jz4740_musb_init':
:(.text+0xaf694): undefined reference to `usb_phy_generic_register'
This adds the ones that are missing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Delete private selfpowered variable, and use common one.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
1. set AUTOREQ to NONE at the beginning of teardown;
2. add delay for dma pipeline to drain;
3. Do not set USB_TDOWN bit for RX teardown.
The CPPI hw has an issue that when tearing down a RX channel, if
another RX channel is receiving data, the CPPI will lockup.
To workaround the issue, do not set the CPPI TD bit. The steps before
this point ensures the CPPI channel will be torn down properly.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
Greg Kroah-Hartman
Felipe Balbi
Tony Lindgren
Sergei Shtylyov
Takeyoshi Kikuchi
Arnd Bergmann
George Cherian
Bin Liu
Dmitry Torokhov
Peter Chen