| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After commit b09b5224fe86 ("usb: chipidea: implement platform shutdown
callback") and commit 43a404577a93 ("usb: chipidea: host: set host to
be null after hcd is freed") a NULL pointer dereference is caused
on i.MX23 during shutdown. So ensure that role is set to CI_ROLE_END and
we finish interrupt handling before the hcd is deallocated. This avoids
the NULL pointer dereference.
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Fixes: b09b5224fe86 ("usb: chipidea: implement platform shutdown callback")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Since the controller on R-Car Gen3 doesn't have any status registers
to detect initialization (LPSTS.SUSPM = 1) and the initialization needs
up to 45 usec, this patch adds wait after the initialization. Otherwise,
writing other registers (e.g. INTENB0) will fail.
Fixes: de18757e272d ("usb: renesas_usbhs: add R-Car Gen3 power control")
Cc: <stable@vger.kernel.org> # v4.6+
Cc: <balbi@kernel.org>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Increase ohci watchout delay to 275 ms. Previous delay was 250 ms
with 20 ms of slack, after removing slack time some ohci controllers don't
respond in time. Logs from systems with controllers that have the
issue would show "HcDoneHead not written back; disabled"
Signed-off-by: Bryan Paluch <bryanpaluch@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we're booting pandaboard using NFSroot over built-in g_ether, we
can get the following after booting once and doing a warm reset:
g_ether gadget: ecm_open
g_ether gadget: notify connect true
...
WARNING: CPU: 0 PID: 1 at drivers/bus/omap_l3_noc.c:147
l3_interrupt_handler+0x220/0x34c
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4CFG (Read):
Data Access in User mode du ring Functional access
...
Fix the issue by calling pm_runtime functions from
musb_gadget_queue.
Note that in the long run we should be able to queue the pending
transfers if pm_runtime is not active, and flush the queue from
pm_runtime_resume.
Reported-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we configure musb with 2430 glue as a peripheral, and then rmmod
omap2430 module, we'll get the following error:
[ INFO: HARDIRQ-safe -> HARDIRQ-unsafe lock order detected ]
...
rmmod/413 [HC0[0]:SC0[0]:HE0:SE1] is trying to acquire:
(&phy->mutex){+.+.+.}, at: [<c04b9fd0>] phy_power_off+0x1c/0xb8
[ 204.678710]
and this task is already holding:
(&(&musb->lock)->rlock){-.-...}, at: [<bf3a482c>]
musb_gadget_stop+0x24/0xec [musb_hdrc]
which would create a new lock dependency:
(&(&musb->lock)->rlock){-.-...} -> (&phy->mutex){+.+.+.}
...
This is because some glue layers expect musb_platform_enable/disable
to be called with spinlock held, and 2430 glue layer has USB PHY on
the I2C bus using a mutex.
We could fix the glue layers to take the spinlock, but we still have
a problem of musb_plaform_enable/disable being called in an unbalanced
manner. So that would still lead into USB PHY enable/disable related
problems for omap2430 glue layer.
While it makes sense to only enable USB PHY when needed from PM point
of view, in this case we just can't do it yet without breaking things.
So let's just revert phy_enable/disable related changes instead and
reconsider this after we have fixed musb_platform_enable/disable to
be balanced.
Fixes: a83e17d0f73b ("usb: musb: Improve PM runtime and phy handling for 2430 glue layer")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Socionext LD11 SoC (arch/arm64/boot/dts/socionext/uniphier-ld11.dtsi)
needs to handle 4 reset lines for EHCI.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The reset value of RWC is 0, set RemoteWakeupConnected bit explicitly
before calling ohci_run, it also fixes the issue that the mass
storage stick connected wasn't suspended when the system suspend.
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Johan writes:
USB-serial fixes for v4.9-rc2
Here's a fix for a NULL-deref during probe which could be triggered by a
malicious device, and a fix for some missing error handling in cp210x
that also leaked some bits from the stack. Included is also a new device
id for ftdi_sio.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Make sure we have at least one port before attempting to register a
console.
Currently, at least one driver binds to a "dummy" interface and requests
zero ports for it. Should such an interface also lack endpoints, we get
a NULL-deref during probe.
Fixes: e5b1e2062e05 ("USB: serial: make minor allocation dynamic")
Cc: stable <stable@vger.kernel.org> # 3.11
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
USB2 host inititated resume, and system suspend bus resume
need to use the same USB_RESUME_TIMEOUT as elsewhere.
This resolves a device disconnect issue at system resume seen
on Intel Braswell and Apollolake, but is in no way limited to
those platforms.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If a device is unplugged and replugged during Sx system suspend
some Intel xHC hosts will overwrite the CAS (Cold attach status) flag
and no device connection is noticed in resume.
A device in this state can be identified in resume if its link state
is in polling or compliance mode, and the current connect status is 0.
A device in this state needs to be warm reset.
Intel 100/c230 series PCH specification update Doc #332692-006 Errata #8
Observed on Cherryview and Apollolake as they go into compliance mode
if LFPS times out during polling, and re-plugged devices are not
discovered at resume.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xHC in Wildcatpoint-LP PCH is similar to LynxPoint-LP and need the
same quirks to prevent machines from spurious restart while
shutting them down.
Reported-by: Hasan Mahmood <hasan.mahm@gmail.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current tiocmget implementation would fail to report errors up the
stack and instead leaked a few bits from the stack as a mask of
modem-status flags.
Fixes: 39a66b8d22a3 ("[PATCH] USB: CP2101 Add support for flow control")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Fix to return error code -ENOMEM from the kmalloc() error handling
case instead of 0, as done elsewhere in this function.
Fixes: a19b882c07a6 ("wusb: Stop using the stack for sg crypto scratch space")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Felipe writes:
usb: fixes for v4.9-rc2
First set of fixes for v4.9-rc cycle. Nothing major
this time around. The most important patches are the
3 fixes in dwc3 (dma_free_coheren() size fix,
queued request accounting fix and Isochronous
StartTransfer fix) and the 3 reverts on dwc2.
We're also including the late atmel UDC fix which
didn't make it into v4.8-final.
|
|
This reverts commit aa381a7259c3 ("usb: dwc2: gadget: fix TX FIFO size
and address initialization").
The original commit removed the FIFO size programming per endpoint. The
DPTXFSIZn register is also used for DIEPTXFn and the SIZE field is r/w
in dedicated fifo mode. So it isn't appropriate to simply remove this
initialization as it might break existing behavior.
Also, some cores might not have enough fifo space to handle the
programming method used in the reverted patch, resulting in fifo
initialization failure.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This reverts commit ba48eab8866c ("usb: dwc2: gadget: change variable
name to more meaningful").
This is needed to cleanly revert commit aa381a7259c3 ("usb: dwc2:
gadget: fix TX FIFO size and address initialization") which may cause
regressions on some platforms.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Cc: Robert Baldyga <r.baldyga@samsung.com>
Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This adds support to ftdi_sio for the Infineon TriBoard TC2X7
engineering board for first-generation Aurix SoCs with Tricore CPUs.
Mere addition of the device IDs does the job.
Signed-off-by: Stefan Tauner <stefan.tauner@technikum-wien.at>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Pointing an sg list at the stack is verboten and, with
CONFIG_VMAP_STACK=y, will malfunction. Use kmalloc for the wusb
crypto stack space instead.
Untested -- I'm not entirely convinced that this hardware exists in
the wild.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit 2abd9d5fa60f9 ("usb: dwc3: ep0: Add chained TRB support"), the
size of the memory allocated with 'dma_alloc_coherent()' has been modified
but the corresponding calls to 'dma_free_coherent()' have not been updated
accordingly.
This has been spotted with coccinelle, using the following script:
////////////////////
@r@
expression x0, x1, y0, y1, z0, z1, t0, t1, ret;
@@
* ret = dma_alloc_coherent(x0, y0, z0, t0);
...
* dma_free_coherent(x1, y1, ret, t1);
@script:python@
y0 << r.y0;
y1 << r.y1;
@@
if y1.find(y0) == -1:
print "WARNING: sizes look different: '%s' vs '%s'" % (y0, y1)
////////////////////
Fixes: 2abd9d5fa60f9 ("usb: dwc3: ep0: Add chained TRB support")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
ffs_func_eps_disable is called from atomic context so it cannot sleep
thus cannot grab a mutex. Change the handling of epfile->read_buffer
to use non-sleeping synchronisation method.
Reported-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Michał Nazarewicz <mina86@mina86.com>
Fixes: 9353afbbfa7b ("buffer data from ‘oversized’ OUT requests")
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
epfile->ep is protected by ffs->eps_lock (not epfile->mutex) so clear it
while holding the spin lock.
Tested-by: John Stultz <john.stultz@linaro.org>
Tested-by: Chen Yu <chenyu56@huawei.com>
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Although a host-only controller should not have any associated delay,
some rockchip SOC platforms will not show the correct host-values of
registers until after a delay.
So add a 50 ms sleep when in host-only mode.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We cannot pre-start isochronous endpoints because we
rely on the micro-frame number passed via
XferNotReady command for proper Isochronous
scheduling.
Fixes: 08a36b543803 ("usb: dwc3: gadget: simplify __dwc3_gadget_ep_queue()")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Some requests could be accounted for multiple
times. Let's fix that so each and every requests is
accounted for only once.
Cc: <stable@vger.kernel.org> # v4.8
Fixes: 55a0237f8f47 ("usb: dwc3: gadget: use allocated/queued reqs for LST bit")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If we don't guarantee that we will always get an
interrupt at least when we're queueing our very last
request, we could fall into situation where we queue
every request with 'no_interrupt' set. This will
cause the link to get stuck.
The behavior above has been triggered with g_ether
and dwc3.
Cc: <stable@vger.kernel.org>
Reported-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Since commit c32b5bcfa3c4 ("ARM: dts: at91: Fix USB endpoint nodes"),
atmel_usba_udc fails with:
------------[ cut here ]------------
WARNING: CPU: 0 PID: 0 at include/linux/usb/gadget.h:405
ecm_do_notify+0x188/0x1a0
Modules linked in:
CPU: 0 PID: 0 Comm: swapper Not tainted 4.7.0+ #15
Hardware name: Atmel SAMA5
[<c010ccfc>] (unwind_backtrace) from [<c010a7ec>] (show_stack+0x10/0x14)
[<c010a7ec>] (show_stack) from [<c0115c10>] (__warn+0xe4/0xfc)
[<c0115c10>] (__warn) from [<c0115cd8>] (warn_slowpath_null+0x20/0x28)
[<c0115cd8>] (warn_slowpath_null) from [<c04377ac>] (ecm_do_notify+0x188/0x1a0)
[<c04377ac>] (ecm_do_notify) from [<c04379a4>] (ecm_set_alt+0x74/0x1ac)
[<c04379a4>] (ecm_set_alt) from [<c042f74c>] (composite_setup+0xfc0/0x19f8)
[<c042f74c>] (composite_setup) from [<c04356e8>] (usba_udc_irq+0x8f4/0xd9c)
[<c04356e8>] (usba_udc_irq) from [<c013ec9c>] (handle_irq_event_percpu+0x9c/0x158)
[<c013ec9c>] (handle_irq_event_percpu) from [<c013ed80>] (handle_irq_event+0x28/0x3c)
[<c013ed80>] (handle_irq_event) from [<c01416d4>] (handle_fasteoi_irq+0xa0/0x168)
[<c01416d4>] (handle_fasteoi_irq) from [<c013e3f8>] (generic_handle_irq+0x24/0x34)
[<c013e3f8>] (generic_handle_irq) from [<c013e640>] (__handle_domain_irq+0x54/0xa8)
[<c013e640>] (__handle_domain_irq) from [<c010b214>] (__irq_svc+0x54/0x70)
[<c010b214>] (__irq_svc) from [<c0107eb0>] (arch_cpu_idle+0x38/0x3c)
[<c0107eb0>] (arch_cpu_idle) from [<c0137300>] (cpu_startup_entry+0x9c/0xdc)
[<c0137300>] (cpu_startup_entry) from [<c0900c40>] (start_kernel+0x354/0x360)
[<c0900c40>] (start_kernel) from [<20008078>] (0x20008078)
---[ end trace e7cf9dcebf4815a6 ]---
Fixes: c32b5bcfa3c4 ("ARM: dts: at91: Fix USB endpoint nodes")
Cc: <stable@vger.kernel.org>
Reported-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Pull MIPS updates from Ralf Baechle:
"This is the main MIPS pull request for 4.9:
MIPS core arch code:
- traps: 64bit kernels should read CP0_EBase 64bit
- traps: Convert ebase to KSEG0
- c-r4k: Drop bc_wback_inv() from icache flush
- c-r4k: Split user/kernel flush_icache_range()
- cacheflush: Use __flush_icache_user_range()
- uprobes: Flush icache via kernel address
- KVM: Use __local_flush_icache_user_range()
- c-r4k: Fix flush_icache_range() for EVA
- Fix -mabi=64 build of vdso.lds
- VDSO: Drop duplicated -I*/-E* aflags
- tracing: move insn_has_delay_slot to a shared header
- tracing: disable uprobe/kprobe on compact branch instructions
- ptrace: Fix regs_return_value for kernel context
- Squash lines for simple wrapper functions
- Move identification of VP(E) into proc.c from smp-mt.c
- Add definitions of SYNC barrierstype values
- traps: Ensure full EBase is written
- tlb-r4k: If there are wired entries, don't use TLBINVF
- Sanitise coherentio semantics
- dma-default: Don't check hw_coherentio if device is non-coherent
- Support per-device DMA coherence
- Adjust MIPS64 CAC_BASE to reflect Config.K0
- Support generating Flattened Image Trees (.itb)
- generic: Introduce generic DT-based board support
- generic: Convert SEAD-3 to a generic board
- Enable hardened usercopy
- Don't specify STACKPROTECTOR in defconfigs
Octeon:
- Delete dead code and files across the platform.
- Change to use all memory into use by default.
- Rename upper case variables in setup code to lowercase.
- Delete legacy hack for broken bootloaders.
- Leave maintaining the link state to the actual ethernet/PHY drivers.
- Add DTS for D-Link DSR-500N.
- Fix PCI interrupt routing on D-Link DSR-500N.
Pistachio:
- Remove ANDROID_TIMED_OUTPUT from defconfig
TX39xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
TX49xx:
- Move GPIO setup from .mem_setup() to .arch_init()
- Convert to Common Clock Framework
txx9wdt:
- Add missing clock (un)prepare calls for CCF
BMIPS:
- Add PW, GPIO SDHCI and NAND device node names
- Support APPENDED_DTB
- Add missing bcm97435svmb to DT_NONE
- Rename bcm96358nb4ser to bcm6358-neufbox4-sercom
- Add DT examples for BCM63268, BCM3368 and BCM6362
- Add support for BCM3368 and BCM6362
PCI
- Reduce stack frame usage
- Use struct list_head lists
- Support for CONFIG_PCI_DOMAINS_GENERIC
- Make pcibios_set_cache_line_size an initcall
- Inline pcibios_assign_all_busses
- Split pci.c into pci.c & pci-legacy.c
- Introduce CONFIG_PCI_DRIVERS_LEGACY
- Support generic drivers
CPC
- Convert bare 'unsigned' to 'unsigned int'
- Avoid lock when MIPS CM >= 3 is present
GIC:
- Delete unused file smp-gic.c
mt7620:
- Delete unnecessary assignment for the field "owner" from PCI
BCM63xx:
- Let clk_disable() return immediately if clk is NULL
pm-cps:
- Change FSB workaround to CPU blacklist
- Update comments on barrier instructions
- Use MIPS standard lightweight ordering barrier
- Use MIPS standard completion barrier
- Remove selection of sync types
- Add MIPSr6 CPU support
- Support CM3 changes to Coherence Enable Register
SMP:
- Wrap call to mips_cpc_lock_other in mips_cm_lock_other
- Introduce mechanism for freeing and allocating IPIs
cpuidle:
- cpuidle-cps: Enable use with MIPSr6 CPUs.
SEAD3:
- Rewrite to use DT and generic kernel feature.
USB:
- host: ehci-sead3: Remove SEAD-3 EHCI code
FBDEV:
- cobalt_lcdfb: Drop SEAD3 support
dt-bindings:
- Document a binding for simple ASCII LCDs
auxdisplay:
- img-ascii-lcd: driver for simple ASCII LCD displays
irqchip i8259:
- i8259: Add domain before mapping parent irq
- i8259: Allow platforms to override poll function
- i8259: Remove unused i8259A_irq_pending
Malta:
- Rewrite to use DT
of/platform:
- Probe "isa" busses by default
CM:
- Print CM error reports upon bus errors
Module:
- Migrate exception table users off module.h and onto extable.h
- Make various drivers explicitly non-modular:
- Audit and remove any unnecessary uses of module.h
mailmap:
- Canonicalize to Qais' current email address.
Documentation:
- MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
Loongson1C:
- Add CPU support for Loongson1C
- Add board support
- Add defconfig
- Add RTC support for Loongson1C board
All this except one Documentation fix has sat in linux-next and has
survived Imagination's automated build test system"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (127 commits)
Documentation: MIPS supports HAVE_REGS_AND_STACK_ACCESS_API
MIPS: ptrace: Fix regs_return_value for kernel context
MIPS: VDSO: Drop duplicated -I*/-E* aflags
MIPS: Fix -mabi=64 build of vdso.lds
MIPS: Enable hardened usercopy
MIPS: generic: Convert SEAD-3 to a generic board
MIPS: generic: Introduce generic DT-based board support
MIPS: Support generating Flattened Image Trees (.itb)
MIPS: Adjust MIPS64 CAC_BASE to reflect Config.K0
MIPS: Print CM error reports upon bus errors
MIPS: Support per-device DMA coherence
MIPS: dma-default: Don't check hw_coherentio if device is non-coherent
MIPS: Sanitise coherentio semantics
MIPS: PCI: Support generic drivers
MIPS: PCI: Introduce CONFIG_PCI_DRIVERS_LEGACY
MIPS: PCI: Split pci.c into pci.c & pci-legacy.c
MIPS: PCI: Inline pcibios_assign_all_busses
MIPS: PCI: Make pcibios_set_cache_line_size an initcall
MIPS: PCI: Support for CONFIG_PCI_DOMAINS_GENERIC
MIPS: PCI: Use struct list_head lists
...
|
|
Kernel source files need not include <linux/kconfig.h> explicitly
because the top Makefile forces to include it with:
-include $(srctree)/include/linux/kconfig.h
This commit removes explicit includes except the following:
* arch/s390/include/asm/facilities_src.h
* tools/testing/radix-tree/linux/kernel.h
These two are used for host programs.
Link: http://lkml.kernel.org/r/1473656164-11929-1-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull more vfs updates from Al Viro:
">rename2() work from Miklos + current_time() from Deepa"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs: Replace current_fs_time() with current_time()
fs: Replace CURRENT_TIME_SEC with current_time() for inode timestamps
fs: Replace CURRENT_TIME with current_time() for inode timestamps
fs: proc: Delete inode time initializations in proc_alloc_inode()
vfs: Add current_time() api
vfs: add note about i_op->rename changes to porting
fs: rename "rename2" i_op to "rename"
vfs: remove unused i_op->rename
fs: make remaining filesystems use .rename2
libfs: support RENAME_NOREPLACE in simple_rename()
fs: support RENAME_NOREPLACE for local filesystems
ncpfs: fix unused variable warning
|
|
|
|
Pull ARM SoC late DT updates from Arnd Bergmann:
"These updates have been kept in a separate branch mostly because they
rely on updates to the respective clk drivers to keep the shared
header files in sync.
- The Renesas r8a7796 (R-Car M3-W) platform gets added, this is an
automotive SoC similar to the ⅹ8a7795 chip we already support, but
the dts changes rely on a clock driver change that has been merged
for v4.9 through the clk tree.
- The Amlogic meson-gxbb (S905) platform gains support for a few
drivers merged through our tree, in particular the network and usb
driver changes are required and included here, and also the clk
tree changes.
- The Allwinner platforms have seen a large-scale change to their clk
drivers and the dts file updates must come after that. This
includes the newly added Nextthing GR8 platform, which is derived
from sun5i/A13.
- Some integrator (arm32) changes rely on clk driver changes.
- A single patch for lpc32xx has no such dependency but wasn't added
until just before the merge window"
* tag 'armsoc-late' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
ARM: dts: lpc32xx: add device node for IRAM on-chip memory
ARM: dts: sun8i: Add accelerometer to polaroid-mid2407pxe03
ARM: dts: sun8i: enable UART1 for iNet D978 Rev2 board
ARM: dts: sun8i: add pinmux for UART1 at PG
dts: sun8i-h3: add I2C0-2 peripherals to H3 SOC
dts: sun8i-h3: add pinmux definitions for I2C0-2
dts: sun8i-h3: associate exposed UARTs on Orange Pi Boards
dts: sun8i-h3: split off RTS/CTS for UART1 in seperate pinmux
dts: sun8i-h3: add pinmux definitions for UART2-3
ARM: dts: sun9i: a80-optimus: Disable EHCI1
ARM: dts: sun9i: cubieboard4: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: a80-optimus: Add AXP806 PMIC device node and regulators
ARM: dts: sun9i: cubieboard4: Declare AXP809 SW regulator as unused
ARM: dts: sun9i: a80-optimus: Declare AXP809 SW regulator as unused
ARM: dts: sun8i: Add touchscreen node for sun8i-a33-ga10h
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2809pxe04
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-polaroid-mid2407pxe03
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-inet86dz
ARM: dts: sun8i: Add touchscreen node for sun8i-a23-gt90h
ARM64: dts: meson-gxbb-vega-s95: Enable USB Nodes
...
|
|
The SEAD-3 board is now probing its EHCI controller using the generic
EHCI driver & its generic-ehci device tree binding. Remove the unused
SEAD-3 specific EHCI code.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14052/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This reverts commit e6c7efdcb76f11b04e3d3f71c8d764ab75c9423b.
Turns out it was totally wrong. The memory is supposed to be bound to
the kref, as the original code was doing correctly, not the
device/driver binding as the devm_kzalloc() would cause.
This fixes an oops when read would be called after the device was
unbound from the driver.
Reported-by: Ladislav Michl <ladis@linux-mips.org>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable <stable@vger.kernel.org> # 3.12+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CURRENT_TIME macro is not appropriate for filesystems as it
doesn't use the right granularity for filesystem timestamps.
Use current_time() instead.
CURRENT_TIME is also not y2038 safe.
This is also in preparation for the patch that transitions
vfs timestamps to use 64 bit time and hence make them
y2038 safe. As part of the effort current_time() will be
extended to do range checks. Hence, it is necessary for all
file system timestamps to use current_time(). Also,
current_time() will be transitioned along with vfs to be
y2038 safe.
Note that whenever a single call to current_time() is used
to change timestamps in different inodes, it is because they
share the same time granularity.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Felipe Balbi <balbi@kernel.org>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Acked-by: David Sterba <dsterba@suse.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Signed-off-by: Kyle Jones <kyle@kf5jwc.us>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to (badf6d47f8a9 "usb: common: rework CONFIG_USB_COMMON logic")
we should select USB_COMMON at Kconfig when usb common stuffs are needed,
but some of Kconfig enties have not followed it, update them.
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In USB20 specification, describes in chapter 9.4.5: The Remote Wakeup
field can be modified by the SetFeature() and ClearFeature() requests
using the DEVICE_REMOTE_WAKEUP feature selector.
In USB30 specification, also describes in chapter 9.4.5: The Function
Remote Wakeup field can be modified by the SetFeature() requests
using the FUNCTION_SUSPEND feature selector. In chapter 9.4.9 Set
Feature reference, it describes Function Remote Wake Enabled/Disabled
at suspend options by SET_FEATURE.
In USB30 specification only mentioned SetFeature(), so we need use
SET_FEATURE replace CLEAR_FEATURE to disable USB30 function remote
wakeup in suspend options.
Signed-off-by: Yonglong Wu <yonglong.wu@mediatek.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit adds a new trigger responsible for turning on LED when USB
device gets connected to the selected USB port. This can can useful for
various home routers that have USB port(s) and a proper LED telling user
a device is connected.
The trigger gets its documentation file but basically it just requires
enabling it and selecting USB ports (e.g. echo 1 > ports/usb1-1).
There was a long discussion on design of this driver. Its current state
is a result of picking them most adjustable solution as others couldn't
handle all cases.
1) It wasn't possible for the driver to register separated trigger for
each USB port. Some physical USB ports are handled by more than one
controller and so by more than one USB port. E.g. USB 2.0 physical
port may be handled by OHCI's port and EHCI's port.
It's also not possible to assign more than 1 trigger to a single LED
and implementing such feature would be tricky due to syncing triggers
and sysfs conflicts with old triggers.
2) Another idea was to register trigger per USB hub. This wouldn't allow
handling devices with multiple USB LEDs and controllers (hubs)
controlling more than 1 physical port. It's common for hubs to have
few ports and each may have its own LED.
This final trigger is highly flexible. It allows selecting any USB ports
for any LED. It was also modified (comparing to the initial version) to
allow choosing ports rather than having user /guess/ proper names. It
was successfully tested on SmartRG SR400ac which has 3 USB LEDs,
2 physical ports and 3 controllers.
It was noted USB subsystem already has usb-gadget and usb-host triggers
but they are pretty trivial ones. They indicate activity only and can't
have ports specified.
In future it may be good idea to consider adding activity support to
usbport as well. This should allow switching to this more generic driver
and maybe marking old ones as obsolete.
This can be implemented with another sysfs file for setting mode. The
default mode wouldn't change so there won't be ABI breakage and so such
feature can be safely implemented later.
There was also an idea of supporting other devices (PCI, SDIO, etc.) but
as this driver already contains some USB specific code (and will get
more) these should be probably separated drivers (triggers).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver should initialize controller only, PHY initialization should
be handled by separated PHY driver. We already have phy-bcm-ns-usb2 in
place so let it makes its duty.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We get 1 warning when building kernel with W=1:
drivers/usb/core/hcd.c:2390:5: warning: no previous prototype for 'usb_bus_start_enum' [-Wmissing-prototypes]
In fact, these functions are declared in linux/usb/otg.h, so this patch
adds the missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We print an error message when platform_device_register_full()
fails, but the initialization of the argument has been removed,
as shown in this warning:
drivers/usb/musb/da8xx.c: In function 'da8xx_probe':
drivers/usb/musb/da8xx.c:521:3: error: 'ret' may be used uninitialized in this function [-Werror=maybe-uninitialized]
This modifies the function to assign the return code before
checking it, and does uses the same method in the check for
usb_phy_generic_register() as well.
Fixes: 947c49afe41f ("usb: musb: da8xx: Remove mach code")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With the session bit based PM runtime working on musb, we've
implemented few quirks to attempt to detect the current state of
the hardware. One of the quirks is for invalid VBUS as peripheral,
but it is not working in all cases.
If we start musb on dm3730 as a peripheral with no cable connected,
we will get the devctl 91 state once and will never idle as there
are not further interrupts from musb. So we need to ignore the first
devctl 91 state as there will be more interrupts if we're connected.
The invalid VBUS state also can happen always when connected to
certain USB hubs. Looks like musb on dm3730 can claim invalid VBUS
with some hubs while 3717-evm and BeagleBone don't. This causes
session as peripheral to fail for dm3730 with some hubs.
This too is fixed by ignoring only the first invalid VBUS. When
connected, we can just look at the session bit as that will clear
automatically when the session ends.
Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If we unconfigure musb as a USB peripheral with cable connected,
and then remove the cable, no interrupts will happen. And musb
thinks we're still connected keeping the device active.
Now with the session bit based PM runtime working for musb, we
can fix this issue by calling musb irq_work. That rechecks the
devctl register and reconfigures PM runtime based on the devctl.
Fixes: 467d5c980709 ("usb: musb: Implement session bit based runtime PM for musb-core")
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Export musb_root_disconnect for use in modules, so that musb glue
code build as module can use it.
This fixes the buildbot errors for -next in arm64-allmodconfig
and arm-allmodconfig.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 7cba17ec9adc8cf ("musb: sunxi: Add support for platform_set_mode")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes a NULL pointer dereference caused by a race codition in
the probe function of the legousbtower driver. It re-structures the
probe function to only register the interface after successfully reading
the board's firmware ID.
The probe function does not deregister the usb interface after an error
receiving the devices firmware ID. The device file registered
(/dev/usb/legousbtower%d) may be read/written globally before the probe
function returns. When tower_delete is called in the probe function
(after an r/w has been initiated), core dev structures are deleted while
the file operation functions are still running. If the 0 address is
mappable on the machine, this vulnerability can be used to create a
Local Priviege Escalation exploit via a write-what-where condition by
remapping dev->interrupt_out_buffer in tower_write. A forged USB device
and local program execution would be required for LPE. The USB device
would have to delay the control message in tower_probe and accept
the control urb in tower_open whilst guest code initiated a write to the
device file as tower_delete is called from the error in tower_probe.
This bug has existed since 2003. Patch tested by emulated device.
Reported-by: James Patrick-Evans <james@jmp-e.com>
Tested-by: James Patrick-Evans <james@jmp-e.com>
Signed-off-by: James Patrick-Evans <james@jmp-e.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This should fix the last holes against malicious devices
still open in cdc-acm. It cannot go into stable due to
the introduction of the common parser.
The fix for stable already merged also covers the problems this patch
fixes.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull "Amlogic driver updates for v4.9, 2nd round" from Kevin Hilman:
- media: update IR support for newer SoCs
- firmware: add secure monitor driver
- net: new stmmac glue driver
- usb: udd DWC2 support for meson-gxbb
- clocks: expose more clock IDs for use by DT
- DT binding updates
* tag 'amlogic-drivers-2' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (21 commits)
clk: gxbb: expose i2c clocks
clk: gxbb: expose USB clocks
clk: gxbb: expose spifc clock
clk: gxbb: expose MPLL2 clock for use by DT
Documentation: dt-bindings: Add documentation for the Meson USB2 PHYs
usb: dwc2: add support for Meson8b and GXBB SoCs
net: stmmac: update the module description of the dwmac-meson driver
net: stmmac: add a glue driver for the Amlogic Meson 8b / GXBB DWMAC
stmmac: introduce get_stmmac_bsp_priv() helper
net: dt-bindings: Document the new Meson8b and GXBB DWMAC bindings
clk: meson-gxbb: Export PWM related clocks for DT
meson: clk: Add support for clock gates
gxbb: clk: Adjust MESON_GATE macro to be shared with meson8b
clk: meson: Copy meson8b CLKID defines to private header file
meson: clk: Rename register names according to Amlogic datasheet
meson: clk: Move register definitions to meson8b.h
clk: meson: Rename meson8b-clkc.c to reflect gxbb naming convention
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
media: rc: meson-ir: Add support for newer versions of the IR decoder
...
|
|
This reverts commit c9ffc78745f89e300fe704348dd8e6800acf4d18 as it was
reported to be broken.
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Jim Baxter <jim_baxter@mentor.com>
Cc: Harish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want/need the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Stefan Wahren
Yoshihiro Shimoda
Bryan Paluch
Tony Lindgren
Masahiro Yamada
Wenyou Yang
Greg Kroah-Hartman
Johan Hovold
Mathias Nyman
Wei Yongjun
John Youn
Stefan Tauner
Andy Lutomirski
Christophe JAILLET
Michal Nazarewicz
Heiko Stuebner
Felipe Balbi
Alexandre Belloni
Linus Torvalds
Al Viro
Paul Burton
Deepa Dinamani
Kyle Jones
Peter Chen
Yonglong Wu
Rafał Miłecki
Baoyou Xie
Arnd Bergmann
Hans de Goede
Oliver Neukum