| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull USB fixes from Greg KH:
"Here's a round of USB fixes for 4.0-rc3.
Nothing major, the usual gadget, xhci and usb-serial fixes and a few
new device ids as well.
All have been in linux-next successfully"
* tag 'usb-4.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (36 commits)
xhci: Workaround for PME stuck issues in Intel xhci
xhci: fix reporting of 0-sized URBs in control endpoint
usb: ftdi_sio: Add jtag quirk support for Cyber Cortex AV boards
USB: ch341: set tty baud speed according to tty struct
USB: serial: cp210x: Adding Seletek device id's
USB: pl2303: disable break on shutdown
USB: mxuport: fix null deref when used as a console
USB: serial: clean up bus probe error handling
USB: serial: fix port attribute-creation race
USB: serial: fix tty-device error handling at probe
USB: serial: fix potential use-after-free after failed probe
USB: console: add dummy __module_get
USB: ftdi_sio: add PIDs for Actisense USB devices
Revert "USB: serial: make bulk_out_size a lower limit"
cdc-acm: Add support for Denso cradle CU-321
usb-storage: support for more than 8 LUNs
uas: Add US_FL_NO_REPORT_OPCODES for JMicron JMS539
USB: usbfs: don't leak kernel data in siginfo
xhci: Clear the host side toggle manually when endpoint is 'soft reset'
xhci: Allocate correct amount of scratchpad buffers
...
|
|
Make sure to handle an infinite timeout (0).
Note that wait_until_sent is currently never called with a 0-timeout
argument due to a bug in tty_wait_until_sent.
Fixes: dcf010503966 ("USB: serial: add generic wait_until_sent
implementation")
Cc: stable <stable@vger.kernel.org> # v3.10
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The xhci in Intel Sunrisepoint and Cherryview platforms need a driver
workaround for a Stuck PME that might either block PME events in suspend,
or create spurious PME events preventing runtime suspend.
Workaround is to clear a internal PME flag, BIT(28) in a vendor specific
PMCTRL register at offset 0x80a4, in both suspend resume callbacks
Without this, xhci connected usb devices might never be able to wake up the
system from suspend, or prevent device from going to suspend (xhci d3)
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a control transfer has a short data stage, the xHCI controller generates
two transfer events: a COMP_SHORT_TX event that specifies the untransferred
amount, and a COMP_SUCCESS event. But when the data stage is not short, only the
COMP_SUCCESS event occurs. Therefore, xhci-hcd must set urb->actual_length to
urb->transfer_buffer_length while processing the COMP_SUCCESS event, unless
urb->actual_length was set already by a previous COMP_SHORT_TX event.
The driver checks this by seeing whether urb->actual_length == 0, but this alone
is the wrong test, as it is entirely possible for a short transfer to have an
urb->actual_length = 0.
This patch changes the xhci driver to rely on a new td->urb_length_set flag,
which is set to true when a COMP_SHORT_TX event is received and the URB length
updated at that stage.
This fixes a bug which affected the HSO plugin, which relies on URBs with
urb->actual_length == 0 to halt re-submitting the RX URB in the control
endpoint.
Cc: <stable@vger.kernel.org>
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Johan writes:
USB-serial fixes for v4.0-rc3
Here are a few fixes for reported problems including a usb-debug device
buffer overflow, potential use-after-free on failed probe, and a couple
of issues with the USB console.
Some new device IDs are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This patch integrates Cyber Cortex AV boards with the existing
ftdi_jtag_quirk in order to use serial port 0 with JTAG which is
required by the manufacturers' software.
Steps: 2
[ftdi_sio_ids.h]
1. Defined the device PID
[ftdi_sio.c]
2. Added a macro declaration to the ids array, in order to enable the
jtag quirk for the device.
Signed-off-by: Max Mansfield <max.m.mansfield@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The ch341_set_baudrate() function initialize the device baud speed
according to the value on priv->baud_rate. By default the ch341_open() set
it to a hardcoded value (DEFAULT_BAUD_RATE 9600). Unfortunately, the
tty_struct is not initialized with the same default value. (usually 56700)
This means that the tty_struct and the device baud rate generator are not
synchronized after opening the port.
Fixup is done by calling ch341_set_termios() if tty exist.
Remove unnecessary variable priv->baud_rate setup as it's already done by
ch341_port_probe().
Remove unnecessary call to ch341_set_{handshake,baudrate}() in
ch341_open() as there already called in ch341_configure() and
ch341_set_termios()
Signed-off-by: Nicolas PLANEL <nicolas.planel@enovance.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
These device ID's are not associated with the cp210x module currently,
but should be. This patch allows the devices to operate upon connecting
them to the usb bus as intended.
Signed-off-by: Michiel van de Garde <mgparser@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Currently an enabled break state is not disabled on final close nor on
re-open and has to be disabled manually.
Fix this by disabling break on port shutdown.
Reported-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Tested-by: Jari Ruusu <jariruusu@users.sourceforge.net>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Fix null-pointer dereference at probe when the device is used as a
console, in which case the tty argument to open will be NULL.
Fixes: ee467a1f2066 ("USB: serial: add Moxa UPORT 12XX/14XX/16XX
driver")
Cc: stable <stable@vger.kernel.org> # v3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Clean up bus probe error handling by separating success and error paths.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Fix attribute-creation race with userspace by using the port device
groups field to create the port attributes.
Also use %u when printing the port number, which is unsigned, even
though we do not currently support more than 128 ports per device.
Reported-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Add missing error handling when registering the tty device at port
probe. This avoids trying to remove an uninitialised character device
when the port device is removed.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Takashi Iwai <tiwai@suse.de>
Cc: stable <stable@vger.kernel.org> # v2.6.12
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Fix return value in probe error path, which could end up returning
success (0) on errors. This could in turn lead to use-after-free or
double free (e.g. in port_remove) when the port device is removed.
Fixes: c706ebdfc895 ("USB: usb-serial: call port_probe and port_remove
at the right times")
Cc: stable <stable@vger.kernel.org> # v2.6.31
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Greg Kroah-Hartman <greg@kroah.com>
|
|
Add call to __module_get when initialising the fake tty in
usb_console_setup to match the module_put in release_one_tty.
Note that the tty-driver (i.e. usb-serial core) must be compiled-in to
enable the usb console so the __module_get is essentially a noop as
driver->owner will be null.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
These product identifiers (PID) all deal with marine NMEA format data
used on motor boats and yachts. We supply the programmed devices to
Chetco, for use inside their equipment. The PIDs are a direct copy of
our Windows device drivers (FTDI drivers with altered PIDs).
Signed-off-by: Mark Glover <mark@actisense.com>
Cc: stable <stable@vger.kernel.org>
[johan: edit commit message slightly ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This reverts commit 5083fd7bdfe6760577235a724cf6dccae13652c2.
A bulk-out size smaller than the end-point size is indeed valid. The
offending commit broke the usb-debug driver for EHCI debug devices,
which use 8-byte buffers.
Fixes: 5083fd7bdfe6 ("USB: serial: make bulk_out_size a lower limit")
Reported-by: "Li, Elvin" <elvin.li@intel.com>
Cc: stable <stable@vger.kernel.org> # v3.15
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
In order to support an older USB cradle by Denso, I added its vendor- and product-ID to the array of usb_device_id acm_ids. In this way cdc-acm feels responsible for this cradle. The related /dev/ttyACM node is being created properly, and the data transfer works.
However, later cradle models by Denso do have proper descriptors, so the patch is not required for these. At the same time both the older and the later model have the same vendor- and product-ID, but they both work with the patched driver.
Declaration of the Denso cradles I tested:
- both models have the same IDs: vendorID 0x076d, productID 0x0006
- older model: Denso CU-321 (descriptors not properly set)
- later model: Denso CU-821 (with proper descriptors)
Signed-off-by: Bjoern Gerhart <oss@airbjorn.de>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is necessary to make some storage arrays work.
Some storage devices have more than 8 LUNs. In addition
you can hook up a WideSCSI bus to USB. In these cases even
level 2 devices can have more than 8 LUNs. For them
it is necessary to simply believe the class specific
command and report its result back to the SCSI layer.
Off by one Alan noticed is fixed.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Like the JMicron JMS567 enclosures with the JMS539 choke on report-opcodes,
so avoid it.
Tested-and-reported-by: Tom Arild Naess <tanaess@gmail.com>
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a signal is delivered, the information in the siginfo structure
is copied to userspace. Good security practice dicatates that the
unused fields in this structure should be initialized to 0 so that
random kernel stack data isn't exposed to the user. This patch adds
such an initialization to the two places where usbfs raises signals.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dave Mielke <dave@mielke.cc>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Main benefit of this is to get xhci connected USB scanners to work.
Some devices use a clear endpoint halt request as a 'soft reset' even if
the endpoint is not halted. This will clear the toggle and sequence on the
device side. xHCI however refuses to reset a non-halted endpoint, so instead
we need to issue a configure endpoint command on xHCI to clear its host side
toggle and sequence, and get it in sync with the device side.
Tested-by: Mike Mammarella <mikem@crystalorb.net>
Cc: <stable@vger.kernel.org> # v3.18
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Include the high order bit fields for Max scratchpad buffers when
calculating how many scratchpad buffers are needed.
I'm suprised this hasn't caused more issues, we never allocated more than
32 buffers even if xhci needed more. Either we got lucky and xhci never
really used past that area, or then we got enough zeroed dma memory anyway.
Should be backported as far back as possible
Reported-by: Tim Chen <tim.c.chen@linux.intel.com>
Tested-by: Tim Chen <tim.c.chen@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit 973747928514 ("usb: host: xhci-plat: add support for the Armada
375/38x XHCI controllers") extended the xhci-plat driver to support the Armada
375/38x SoCs, mostly by adding a quirk configuring the MBUS window.
However, that quirk was run before the clock the controllers needs has been
enabled. This usually worked because the clock was first enabled by the
bootloader, and left as such until the driver is probe, where it tries to
access the MBUS configuration registers before enabling the clock.
Things get messy when EPROBE_DEFER is involved during the probe, since as part
of its error path, the driver will rightfully disable the clock. When the
driver will be reprobed, it will retry to access the MBUS registers, but this
time with the clock disabled, which hangs forever.
Fix this by running the quirks after the clock has been enabled by the driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org> # v3.16+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The "Extended Compat ID OS Feature Descriptor Specification" does not
require the (sub)compatible ids to be NUL-terminated, because they
are placed in a fixed-size buffer and only unused parts of it should
contain NULs. If the buffer is fully utilized, there is no place for NULs.
Consequently, the code which uses desc->ext_compat_id never expects the
data contained to be NUL terminated.
If the compatible id is stored after sub-compatible id, and the compatible
id is full length (8 bytes), the (useless) NUL terminator overwrites the
first byte of the sub-compatible id.
If the sub-compatible id is full length (8 bytes), the (useless) NUL
terminator ends up out of the buffer. The situation can happen in the RNDIS
function, where the buffer is a part of struct f_rndis_opts. The next
member of struct f_rndis_opts is a mutex, so its first byte gets
overwritten. The said byte is a part of a mutex'es member which contains
the information on whether the muext is locked or not. This can lead to a
deadlock, because, in a configfs-composed gadget when a function is linked
into a configuration with config_usb_cfg_link(), usb_get_function()
is called, which then calls rndis_alloc(), which tries locking the same
mutex and (wrongly) finds it already locked.
This patch eliminates NUL terminating of the (sub)compatible id.
Cc: <stable@vger.kernel.org> # v3.16+
Fixes: da4243145fb1: "usb: gadget: configfs: OS Extended Compatibility descriptors support"
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In the wrapper the IRQ disable should be done by writing 1's to the
IRQ*_CLR register. Existing code is broken because it instead writes
zeros to IRQ*_SET register.
Fix this by adding functions dwc3_omap_write_irqmisc_clr() and
dwc3_omap_write_irq0_clr() which do the right thing.
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Cc: <stable@vger.kernel.org> # v3.2+
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this patch fixes following sparse warnings:
uvc_v4l2.c:264:29: warning: symbol 'uvc_v4l2_ioctl_ops' was not declared. Should it be static?
uvc_v4l2.c:355:29: warning: symbol 'uvc_v4l2_fops' was not declared. Should it be static?
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this patch fixes following sparse warnings:
g_ffs.c:136:3: warning: symbol 'gfs_configurations' was not declared. Should it be static?
g_ffs.c:281:16: warning: Using plain integer as NULL pointer
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this patch fixes following sparse warnings:
uvc_video.c:283:5: warning: symbol 'uvcg_video_pump' was not declared. Should it be static?
uvc_video.c:342:5: warning: symbol 'uvcg_video_enable' was not declared. Should it be static?
uvc_video.c:381:5: warning: symbol 'uvcg_video_init' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this patch fixes following sparse warnings:
f_sourcesink.c:347:34: warning: symbol 'ss_int_source_comp_desc' was not declared. Should it be static?
f_sourcesink.c:365:34: warning: symbol 'ss_int_sink_comp_desc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this patch fixes following sparse warnings:
f_uac2.c:57:12: warning: symbol 'uac2_name' was not declared. Should it be static?
f_uac2.c:637:36: warning: symbol 'in_clk_src_desc' was not declared. Should it be static?
f_uac2.c:649:36: warning: symbol 'out_clk_src_desc' was not declared. Should it be static?
f_uac2.c:661:39: warning: symbol 'usb_out_it_desc' was not declared. Should it be static?
f_uac2.c:675:39: warning: symbol 'io_in_it_desc' was not declared. Should it be static?
f_uac2.c:689:40: warning: symbol 'usb_in_ot_desc' was not declared. Should it be static?
f_uac2.c:703:40: warning: symbol 'io_out_ot_desc' was not declared. Should it be static?
f_uac2.c:716:34: warning: symbol 'ac_hdr_desc' was not declared. Should it be static?
f_uac2.c:754:34: warning: symbol 'as_out_hdr_desc' was not declared. Should it be static?
f_uac2.c:767:38: warning: symbol 'as_out_fmt1_desc' was not declared. Should it be static?
f_uac2.c:775:32: warning: symbol 'fs_epout_desc' was not declared. Should it be static?
f_uac2.c:785:32: warning: symbol 'hs_epout_desc' was not declared. Should it be static?
f_uac2.c:831:34: warning: symbol 'as_in_hdr_desc' was not declared. Should it be static?
f_uac2.c:844:38: warning: symbol 'as_in_fmt1_desc' was not declared. Should it be static?
f_uac2.c:852:32: warning: symbol 'fs_epin_desc' was not declared. Should it be static?
f_uac2.c:862:32: warning: symbol 'hs_epin_desc' was not declared. Should it be static?
f_uac2.c:1566:21: warning: symbol 'afunc_alloc' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
this patch fixes following sparse warning:
f_hid.c:572:30: warning: symbol 'f_hidg_fops' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We still have a combination of legacy phys and generic phys in
use so we need to support both types of phy for musb_dsps.c.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The renesas usbhs driver calls extcon_get_edev_by_phandle(), which
is defined in drivers/extcon/extcon-class.c, and that can be a
loadable module. If the extcon-class support is disabled, usbhs
will work correctly for all devices that do not need extcon.
However, if extcon-class is a loadable module, and usbhs is
built-in, the kernel fails to link. In order to solve that,
we need a Kconfig dependency that allows extcon to be disabled
but does not allow usbhs built-in if extcon is a module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The value for the multipoint dts property is ignored when parsing with
of_property_read_bool, so we currently have multipoint always set as 1
even if value 0 is specified in the dts file.
Let's fix this to read the value too instead of just the property like
the binding documentation says as otherwise MUSB will fail to work
on devices with Mentor configuration that does not support multipoint.
Cc: Brian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We need a pm_runtime_get_sync() call from
within musb_gadget_pullup() to make sure
registers are accessible at that time.
The problem is that musb_gadget_pullup() is
called with IRQs disabled and, because of that,
we need to tell pm_runtime that this pm_runtime_get_sync()
is IRQ safe.
We can simply add pm_runtime_irq_safe(), however, because
we need to make our read/write accessor function pointers
have been initialized before trying to use them. This means
that all pm_runtime initialization for musb_core needs to
be moved down so that when we call pm_runtime_irq_safe(),
the pm_runtime_get_sync() that it calls on the parent, won't
cause a crash due to NULL musb_read/write accessors.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
f_phonet's ->set_alt() method will call usb_ep_disable()
potentially on an endpoint which is already disabled. That's
something the gadget/function driver must guarantee that it's
always balanced.
In order to balance the calls, just make sure the endpoint
was enabled before by means of checking the validity of
driver_data.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Enable HCD_BH flag for musb host controller driver.
This improves the MSC/UVC through put. With this enabled
even 640x480@30fps webcam streaming is also supported.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Pull kconfig updates from Michal Marek:
"Yann E Morin was supposed to take over kconfig maintainership, but
this hasn't happened. So I'm sending a few kconfig patches that I
collected:
- Fix for missing va_end in kconfig
- merge_config.sh displays used if given too few arguments
- s/boolean/bool/ in Kconfig files for consistency, with the plan to
only support bool in the future"
* 'kconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
kconfig: use va_end to match corresponding va_start
merge_config.sh: Display usage if given too few arguments
kconfig: use bool instead of boolean for type definition attributes
|
|
Pull networking updates from David Miller:
1) Missing netlink attribute validation in nft_lookup, from Patrick
McHardy.
2) Restrict ipv6 partial checksum handling to UDP, since that's the
only case it works for. From Vlad Yasevich.
3) Clear out silly device table sentinal macros used by SSB and BCMA
drivers. From Joe Perches.
4) Make sure the remote checksum code never creates a situation where
the remote checksum is applied yet the tunneling metadata describing
the remote checksum transformation is still present. Otherwise an
external entity might see this and apply the checksum again. From
Tom Herbert.
5) Use msecs_to_jiffies() where applicable, from Nicholas Mc Guire.
6) Don't explicitly initialize timer struct fields, use setup_timer()
and mod_timer() instead. From Vaishali Thakkar.
7) Don't invoke tg3_halt() without the tp->lock held, from Jun'ichi
Nomura.
8) Missing __percpu annotation in ipvlan driver, from Eric Dumazet.
9) Don't potentially perform skb_get() on shared skbs, also from Eric
Dumazet.
10) Fix COW'ing of metrics for non-DST_HOST routes in ipv6, from Martin
KaFai Lau.
11) Fix merge resolution error between the iov_iter changes in vhost and
some bug fixes that occurred at the same time. From Jason Wang.
12) If rtnl_configure_link() fails we have to perform a call to
->dellink() before unregistering the device. From WANG Cong.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (39 commits)
net: dsa: Set valid phy interface type
rtnetlink: call ->dellink on failure when ->newlink exists
com20020-pci: add support for eae single card
vhost_net: fix wrong iter offset when setting number of buffers
net: spelling fixes
net/core: Fix warning while make xmldocs caused by dev.c
net: phy: micrel: disable NAND-tree for KSZ8021, KSZ8031, KSZ8051, KSZ8081
ipv6: fix ipv6_cow_metrics for non DST_HOST case
openvswitch: Fix key serialization.
r8152: restore hw settings
hso: fix rx parsing logic when skb allocation fails
tcp: make sure skb is not shared before using skb_get()
bridge: netfilter: Move sysctl-specific error code inside #ifdef
ipv6: fix possible deadlock in ip6_fl_purge / ip6_fl_gc
ipvlan: add a missing __percpu pcpu_stats
tg3: Hold tp->lock before calling tg3_halt() from tg3_init_one()
bgmac: fix device initialization on Northstar SoCs (condition typo)
qlcnic: Delete existing multicast MAC list before adding new
net/mlx5_core: Fix configuration of log_uar_page_sz
sunvnet: don't change gso data on clones
...
|
|
Pull debugfs patches from Al Viro:
"debugfs patches, mostly to make it possible for something like tracefs
to be transparently automounted on given directory in debugfs.
New primitive in there is debugfs_create_automount(name, parent, func,
arg), which creates a directory and makes its ->d_automount() return
func(arg). Another missing primitive was debugfs_create_file_size() -
open-coded in quite a few places. Dave's patch adds it and converts
the open-code instances to calling it"
* 'debugfs_automount' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
debugfs: Provide a file creation function that also takes an initial size
new primitive: debugfs_create_automount()
debugfs: split end_creating() into success and failure cases
debugfs: take mode-dependent parts of debugfs_get_inode() into callers
fold debugfs_mknod() into callers
fold debugfs_create() into caller
fold debugfs_mkdir() into caller
debugfs_mknod(): get rid useless arguments
fold debugfs_link() into caller
debugfs: kill __create_file()
debugfs: split the beginning and the end of __create_file() off
debugfs_{mkdir,create,link}(): get rid of redundant argument
|
|
Pull ARM SoC driver updates from Olof Johansson:
"These are changes for drivers that are intimately tied to some SoC and
for some reason could not get merged through the respective subsystem
maintainer tree.
This time around, much of this is for at91, with the bulk of it being
syscon and udc drivers.
Also, there's:
- coupled cpuidle support for Samsung Exynos4210
- Renesas 73A0 common-clk work
- of/platform changes to tear down DMA mappings on device destruction
- a few updates to the TI Keystone knav code"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
pcmcia: at91_cf: depend on !ARCH_MULTIPLATFORM
soc: ti: knav_qmss_queue: export API calls for use by user driver
of/platform: teardown DMA mappings on device destruction
usb: gadget: at91_udc: Allocate udc instance
usb: gadget: at91_udc: Update DT binding documentation
usb: gadget: at91_udc: Rework for multi-platform kernel support
usb: gadget: at91_udc: Simplify probe and remove functions
usb: gadget: at91_udc: Remove non-DT handling code
usb: gadget: at91_udc: Document DT clocks and clock-names property
usb: gadget: at91_udc: Drop uclk clock
usb: gadget: at91_udc: Fix clock names
mfd: syscon: Add Atmel SMC binding doc
mfd: syscon: Add atmel-smc registers definition
mfd: syscon: Add Atmel Matrix bus DT binding documentation
mfd: syscon: Add atmel-matrix registers definition
clk: shmobile: fix sparse NULL pointer warning
...
|
|
Provide a file creation function that also takes an initial size so that the
caller doesn't have to set i_size, thus meaning that we don't have to call
deal with ->d_inode in the callers.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull USB patches from Greg KH:
"Here's the big pull request for the USB driver tree for 3.20-rc1.
Nothing major happening here, just lots of gadget driver updates, new
device ids, and a bunch of cleanups.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-3.20-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (299 commits)
usb: musb: fix device hotplug behind hub
usb: dwc2: Fix a bug in reading the endpoint directions from reg.
staging: emxx_udc: fix the build error
usb: Retry port status check on resume to work around RH bugs
Revert "usb: Reset USB-3 devices on USB-3 link bounce"
uhci-hub: use HUB_CHAR_*
usb: kconfig: replace PPC_OF with PPC
ehci-pci: disable for Intel MID platforms (update)
usb: gadget: Kconfig: use bool instead of boolean
usb: musb: blackfin: remove incorrect __exit_p()
USB: fix use-after-free bug in usb_hcd_unlink_urb()
ehci-pci: disable for Intel MID platforms
usb: host: pci_quirks: joing string literals
USB: add flag for HCDs that can't receive wakeup requests (isp1760-hcd)
USB: usbfs: allow URBs to be reaped after disconnection
cdc-acm: kill unnecessary messages
cdc-acm: add sanity checks
usb: phy: phy-generic: Fix USB PHY gpio reset
usb: dwc2: fix USB core dependencies
usb: renesas_usbhs: fix NULL pointer dereference in dma_release_channel()
...
|
|
printk and friends can now format bitmaps using '%*pb[l]'. cpumask
and nodemask also provide cpumask_pr_args() and nodemask_pr_args()
respectively which can be used to generate the two printf arguments
necessary to format the specified cpu/nodemask.
* drivers/uwb/drp.c::uwb_drp_handle_alien_drp() was formatting mas.bm
into a buffer but never used it. Removed.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the normal {} instead of a macro to terminate an array.
Remove the macro too.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This one was driving me mad, with several lines of warnings during the
allmodconfig build for a single bogus pointer cast. The warning was so
verbose due to the indirect macro expansion explanation, and the whole
thing was just for a debug printout.
The bogus pointer-to-integer cast was pointless anyway, so just remove
it, and use '%p' to show the pointer.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In commit ceb6c9c862c8 ("USB / PM: Drop CONFIG_PM_RUNTIME from the
USB core"), all occurrences of CONFIG_PM_RUNTIME in the USB core
code were replaced by CONFIG_PM. This created the following structure
of #ifdef blocks in drivers/usb/core/hub.c:
[...]
#ifdef CONFIG_PM
#ifdef CONFIG_PM
/* always on / undead */
#else
/* dead */
#endif
[...]
This patch removes unnecessary inner "#ifdef CONFIG_PM" as well as
the corresponding dead #else block. This inconsistency was found using
the undertaker-checkpatch tool.
Signed-off-by: Andreas Ruprecht <rupran@einserver.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
Linus Torvalds
Johan Hovold
Mathias Nyman
Aleksander Morgado
Greg Kroah-Hartman
Max Mansfield
Nicolas PLANEL
Michiel vd Garde
Mark Glover
Björn Gerhart
Oliver Neukum
Hans de Goede
Alan Stern
Maxime Ripard
Andrzej Pietrasiewicz
George Cherian
Lad, Prabhakar
Nicholas Mc Guire
Tony Lindgren
Arnd Bergmann
Felipe Balbi
David Howells
Tejun Heo
Joe Perches
Andreas Ruprecht