| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull USB fixes from Greg KH:
"Here are a number of USB fixes for 4.16-rc3
Nothing major, but a number of different fixes all over the place in
the USB stack for reported issues. Mostly gadget driver fixes,
although the typical set of xhci bugfixes are there, along with some
new quirks additions as well.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.16-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (39 commits)
Revert "usb: musb: host: don't start next rx urb if current one failed"
usb: musb: fix enumeration after resume
usb: cdc_acm: prevent race at write to acm while system resumes
Add delay-init quirk for Corsair K70 RGB keyboards
usb: ohci: Proper handling of ed_rm_list to handle race condition between usb_kill_urb() and finish_unlinks()
usb: host: ehci: always enable interrupt for qtd completion at test mode
usb: ldusb: add PIDs for new CASSY devices supported by this driver
usb: renesas_usbhs: missed the "running" flag in usb_dmac with rx path
usb: host: ehci: use correct device pointer for dma ops
usbip: keep usbip_device sockfd state in sync with tcp_socket
ohci-hcd: Fix race condition caused by ohci_urb_enqueue() and io_watchdog_func()
USB: serial: option: Add support for Quectel EP06
xhci: fix xhci debugfs errors in xhci_stop
xhci: xhci debugfs device nodes weren't removed after device plugged out
xhci: Fix xhci debugfs devices node disappearance after hibernation
xhci: Fix NULL pointer in xhci debugfs
xhci: Don't print a warning when setting link state for disabled ports
xhci: workaround for AMD Promontory disabled ports wakeup
usb: dwc3: core: Fix ULPI PHYs and prevent phy_get/ulpi_init during suspend/resume
USB: gadget: udc: Add missing platform_device_put() on error in bdc_pci_probe()
...
|
|
This reverts commit dbac5d07d13e330e6706813c9fde477140fb5d80.
commit dbac5d07d13e ("usb: musb: host: don't start next rx urb if current one failed")
along with commit b5801212229f ("usb: musb: host: clear rxcsr error bit if set")
try to solve the issue described in [1], but the latter alone is
sufficient, and the former causes the issue as in [2], so now revert it.
[1] https://marc.info/?l=linux-usb&m=146173995117456&w=2
[2] https://marc.info/?l=linux-usb&m=151689238420622&w=2
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87cb3 ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Felipe writes:
usb: fixes for v4.16-rc2
First set of fixes for current -rc cycle. Most of the changes are on
dwc3 this time around (59%) with some function changes (25%).
Out of the those, the most important fixes are:
- EP0 TRB counter fix on dwc3
- dwc3-omap stopped missing events during suspend/resume
- maxpacket size fix for ep0 in dwc3
- Descriptor processing fix for functionfs
Apart from these, your usual set of important-but-not-so-critical
fixes all over the place.
|
|
ACM driver may accept data to transmit while system is not fully
resumed. In this case ACM driver buffers data and prepare URBs
on usb anchor list.
There is a little chance that two tasks put a char and initiate
acm_tty_flush_chars(). In such a case, driver will put one URB
twice on usb anchor list.
This patch also reset length of data before resue of a buffer.
This not only prevent sending rubbish, but also lower risc of race.
Without this patch we hit following kernel panic in one of our
stabilty/stress tests.
[ 46.884442] *list_add double add*: new=ffff9b2ab7289330, prev=ffff9b2ab7289330, next=ffff9b2ab81e28e0.
[ 46.884476] Modules linked in: hci_uart btbcm bluetooth rfkill_gpio igb_avb(O) cfg80211 snd_soc_sst_bxt_tdf8532 snd_soc_skl snd_soc_skl_ipc snd_soc_sst_ipc snd_soc_sst_dsp snd_soc_sst_acpi snd_soc_sst_match snd_hda_ext_core snd_hda_core trusty_timer trusty_wall trusty_log trusty_virtio trusty_ipc trusty_mem trusty_irq trusty virtio_ring virtio intel_ipu4_mmu_bxtB0 lib2600_mod_bxtB0 intel_ipu4_isys_mod_bxtB0 lib2600psys_mod_bxtB0 intel_ipu4_psys_mod_bxtB0 intel_ipu4_mod_bxtB0 intel_ipu4_wrapper_bxtB0 intel_ipu4_acpi videobuf2_dma_contig as3638 dw9714 lm3643 crlmodule smiapp smiapp_pll
[ 46.884480] CPU: 1 PID: 33 Comm: kworker/u8:1 Tainted: G U W O 4.9.56-quilt-2e5dc0ac-g618ed69ced6e-dirty #4
[ 46.884489] Workqueue: events_unbound flush_to_ldisc
[ 46.884494] ffffb98ac012bb08 ffffffffad3e82e5 ffffb98ac012bb58 0000000000000000
[ 46.884497] ffffb98ac012bb48 ffffffffad0a23d1 00000024ad6374dd ffff9b2ab7289330
[ 46.884500] ffff9b2ab81e28e0 ffff9b2ab7289330 0000000000000002 0000000000000000
[ 46.884501] Call Trace:
[ 46.884507] [<ffffffffad3e82e5>] dump_stack+0x67/0x92
[ 46.884511] [<ffffffffad0a23d1>] __warn+0xd1/0xf0
[ 46.884513] [<ffffffffad0a244f>] warn_slowpath_fmt+0x5f/0x80
[ 46.884516] [<ffffffffad407443>] __list_add+0xb3/0xc0
[ 46.884521] [<ffffffffad71133c>] *usb_anchor_urb*+0x4c/0xa0
[ 46.884524] [<ffffffffad782c6f>] *acm_tty_flush_chars*+0x8f/0xb0
[ 46.884527] [<ffffffffad782cd1>] *acm_tty_put_char*+0x41/0x100
[ 46.884530] [<ffffffffad4ced34>] tty_put_char+0x24/0x40
[ 46.884533] [<ffffffffad4d3bf5>] do_output_char+0xa5/0x200
[ 46.884535] [<ffffffffad4d3e98>] __process_echoes+0x148/0x290
[ 46.884538] [<ffffffffad4d654c>] n_tty_receive_buf_common+0x57c/0xb00
[ 46.884541] [<ffffffffad4d6ae4>] n_tty_receive_buf2+0x14/0x20
[ 46.884543] [<ffffffffad4d9662>] tty_ldisc_receive_buf+0x22/0x50
[ 46.884545] [<ffffffffad4d9c05>] flush_to_ldisc+0xc5/0xe0
[ 46.884549] [<ffffffffad0bcfe8>] process_one_work+0x148/0x440
[ 46.884551] [<ffffffffad0bdc19>] worker_thread+0x69/0x4a0
[ 46.884554] [<ffffffffad0bdbb0>] ? max_active_store+0x80/0x80
[ 46.884556] [<ffffffffad0c2e10>] kthread+0x110/0x130
[ 46.884559] [<ffffffffad0c2d00>] ? kthread_park+0x60/0x60
[ 46.884563] [<ffffffffadad9917>] ret_from_fork+0x27/0x40
[ 46.884566] ---[ end trace 3bd599058b8a9eb3 ]---
Signed-off-by: Dominik Bozek <dominikx.bozek@intel.com>
Signed-off-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that USB_UHCI_BIG_ENDIAN_MMIO and USB_UHCI_BIG_ENDIAN_DESC are moved
outside of the USB_SUPPORT conditional, simply select them from
SPARC_LEON rather than by the symbol's defaults in drivers/usb/Kconfig,
similar to how it is done for USB_EHCI_BIG_ENDIAN_MMIO and
USB_EHCI_BIG_ENDIAN_DESC.
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: sparclinux@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Acked-by: David S. Miller <davem@davemloft.net>
Patchwork: https://patchwork.linux-mips.org/patch/18560/
|
|
Move the Kconfig symbols USB_UHCI_BIG_ENDIAN_MMIO and
USB_UHCI_BIG_ENDIAN_DESC out of drivers/usb/host/Kconfig, which is
conditional upon USB && USB_SUPPORT, so that it can be freely selected
by platform Kconfig symbols in architecture code.
For example once the MIPS_GENERIC platform selects are fixed in commit
2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN"), the MIPS
32r6_defconfig warns like so:
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_MMIO which has unmet direct dependencies (USB_SUPPORT && USB)
warning: (MIPS_GENERIC) selects USB_UHCI_BIG_ENDIAN_DESC which has unmet direct dependencies (USB_SUPPORT && USB)
Fixes: 2e6522c56552 ("MIPS: Fix typo BIG_ENDIAN to CPU_BIG_ENDIAN")
Signed-off-by: James Hogan <jhogan@kernel.org>
Cc: Corentin Labbe <clabbe.montjoie@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Patchwork: https://patchwork.linux-mips.org/patch/18559/
|
|
Following on from this patch: https://lkml.org/lkml/2017/11/3/516,
Corsair K70 RGB keyboards also require the DELAY_INIT quirk to
start correctly at boot.
Device ids found here:
usb 3-3: New USB device found, idVendor=1b1c, idProduct=1b13
usb 3-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 3-3: Product: Corsair K70 RGB Gaming Keyboard
Signed-off-by: Jack Stocker <jackstocker.93@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a race condition between finish_unlinks->finish_urb() function
and usb_kill_urb() in ohci controller case. The finish_urb calls
spin_unlock(&ohci->lock) before usb_hcd_giveback_urb() function call,
then if during this time, usb_kill_urb is called for another endpoint,
then new ed will be added to ed_rm_list at beginning for unlink, and
ed_rm_list will point to newly added.
When finish_urb() is completed in finish_unlinks() and ed->td_list
becomes empty as in below code (in finish_unlinks() function):
if (list_empty(&ed->td_list)) {
*last = ed->ed_next;
ed->ed_next = NULL;
} else if (ohci->rh_state == OHCI_RH_RUNNING) {
*last = ed->ed_next;
ed->ed_next = NULL;
ed_schedule(ohci, ed);
}
The *last = ed->ed_next will make ed_rm_list to point to ed->ed_next
and previously added ed by usb_kill_urb will be left unreferenced by
ed_rm_list. This causes usb_kill_urb() hang forever waiting for
finish_unlink to remove added ed from ed_rm_list.
The main reason for hang in this race condtion is addition and removal
of ed from ed_rm_list in the beginning during usb_kill_urb and later
last* is modified in finish_unlinks().
As suggested by Alan Stern, the solution for proper handling of
ohci->ed_rm_list is to remove ed from the ed_rm_list before finishing
any URBs. Then at the end, we can add ed back to the list if necessary.
This properly handle the updated ohci->ed_rm_list in usb_kill_urb().
Fixes: 977dcfdc6031 ("USB: OHCI: don't lose track of EDs when a controller dies")
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Aman Deep <aman.deep@samsung.com>
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
At former code, the SETUP stage does not enable interrupt
for qtd completion, it relies on IAA watchdog to complete
interrupt, then the transcation would be considered timeout
if the flag need_io_watchdog is cleared by platform code.
In this commit, we always add enable interrupt for qtd completion,
then the qtd completion can be notified by hardware interrupt.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds support for new CASSY devices to the ldusb driver. The
PIDs are also added to the ignore list in hid-quirks.
Signed-off-by: Karsten Koop <kkoop@ld-didactic.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b3082d ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
commit a8c06e407ef9 ("usb: separate out sysdev pointer from usb_bus")
converted to use hcd->self.sysdev for DMA operations instead of
hcd->self.controller, but forgot to do it for hcd test mode. Replace
the correct one in this commit.
Fixes: a8c06e407ef9 ("usb: separate out sysdev pointer from usb_bus")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Keep usbip_device sockfd state in sync with tcp_socket. When tcp_socket
is reset to null, reset sockfd to -1 to keep it in sync.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Running io_watchdog_func() while ohci_urb_enqueue() is running can
cause a race condition where ohci->prev_frame_no is corrupted and the
watchdog can mis-detect following error:
ohci-platform 664a0800.usb: frame counter not updating; disabled
ohci-platform 664a0800.usb: HC died; cleaning up
Specifically, following scenario causes a race condition:
1. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
2. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
3. ohci_urb_enqueue() sets ohci->prev_frame_no to a frame number
read by ohci_frame_no(ohci)
4. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
5. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section
6. Later, ohci_urb_enqueue() is called
7. ohci_urb_enqueue() calls spin_lock_irqsave(&ohci->lock, flags)
and enters the critical section
8. The timer scheduled on step 4 expires and io_watchdog_func() runs
9. io_watchdog_func() calls spin_lock_irqsave(&ohci->lock, flags)
and waits on it because ohci_urb_enqueue() is already in the
critical section on step 7
10. ohci_urb_enqueue() calls timer_pending(&ohci->io_watchdog) and it
returns false
11. ohci_urb_enqueue() sets ohci->prev_frame_no to new frame number
read by ohci_frame_no(ohci) because the frame number proceeded
between step 3 and 6
12. ohci_urb_enqueue() schedules io_watchdog_func() with mod_timer()
13. ohci_urb_enqueue() calls spin_unlock_irqrestore(&ohci->lock,
flags) and exits the critical section, then wake up
io_watchdog_func() which is waiting on step 9
14. io_watchdog_func() enters the critical section
15. io_watchdog_func() calls ohci_frame_no(ohci) and set frame_no
variable to the frame number
16. io_watchdog_func() compares frame_no and ohci->prev_frame_no
On step 16, because this calling of io_watchdog_func() is scheduled on
step 4, the frame number set in ohci->prev_frame_no is expected to the
number set on step 3. However, ohci->prev_frame_no is overwritten on
step 11. Because step 16 is executed soon after step 11, the frame
number might not proceed, so ohci->prev_frame_no must equals to
frame_no.
To address above scenario, this patch introduces a special sentinel
value IO_WATCHDOG_OFF and set this value to ohci->prev_frame_no when
the watchdog is not pending or running. When ohci_urb_enqueue()
schedules the watchdog (step 4 and 12 above), it compares
ohci->prev_frame_no to IO_WATCHDOG_OFF so that ohci->prev_frame_no is
not overwritten while io_watchdog_func() is running.
Signed-off-by: Shigeru Yoshida <Shigeru.Yoshida@windriver.com>
Signed-off-by: Haiqing Bai <Haiqing.Bai@windriver.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Quectel EP06 is a Cat. 6 LTE modem, and the interface mapping is as
follows:
0: Diag
1: NMEA
2: AT
3: Modem
Interface 4 is QMI and interface 5 is ADB, so they are blacklisted.
This patch should also be considered for -stable. The QMI-patch for this
modem is already in the -stable-queue.
v1->v2:
* Updated commit prefix (thanks Johan Hovold)
* Updated commit message slightly.
Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In function xhci_stop, xhci_debugfs_exit called before xhci_mem_cleanup.
xhci_debugfs_exit removed the xhci debugfs root nodes, xhci_mem_cleanup
called function xhci_free_virt_devices_depth_first which in turn called
function xhci_debugfs_remove_slot.
Function xhci_debugfs_remove_slot removed the nodes for devices, the nodes
folders are sub folder of xhci debugfs.
It is unreasonable to remove xhci debugfs root folder before
xhci debugfs sub folder. Function xhci_mem_cleanup should be called
before function xhci_debugfs_exit.
Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a bug after plugged out USB device, the device and its ep00
nodes are still kept, we need to remove the nodes in xhci_free_dev when
USB device is plugged out.
Fixes: 052f71e25a7e ("xhci: Fix xhci debugfs NULL pointer dereference in resume from hibernate")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
During system resume from hibernation, xhci host is reset, all the
nodes in devices folder are removed in xhci_mem_cleanup function.
Later nodes in /sys/kernel/debug/usb/xhci/* are created again in
function xhci_run, but the nodes already exist, so the nodes still
keep the old ones, finally device nodes in xhci debugfs folder
/sys/kernel/debug/usb/xhci/*/devices/* are disappeared.
This fix removed xhci debugfs nodes before the nodes are re-created,
so all the nodes in xhci debugfs can be re-created successfully.
Fixes: 02b6fdc2a153 ("usb: xhci: Add debugfs interface for xHCI driver")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit dde634057da7 ("xhci: Fix use-after-free in xhci debugfs") causes a
null pointer dereference while fixing xhci-debugfs usage of ring pointers
that were freed during hibernate.
The fix passed addresses to ring pointers instead, but forgot to do this
change for the xhci_ring_trb_show function.
The address of the ring pointer passed to xhci-debugfs was of a temporary
ring pointer "new_ring" instead of the actual ring "ring" pointer. The
temporary new_ring pointer will be set to NULL later causing the NULL
pointer dereference.
This issue was seen when reading xhci related files in debugfs:
cat /sys/kernel/debug/usb/xhci/*/devices/*/ep*/trbs
[ 184.604861] BUG: unable to handle kernel NULL pointer dereference at (null)
[ 184.613776] IP: xhci_ring_trb_show+0x3a/0x890
[ 184.618733] PGD 264193067 P4D 264193067 PUD 263238067 PMD 0
[ 184.625184] Oops: 0000 [#1] SMP
[ 184.726410] RIP: 0010:xhci_ring_trb_show+0x3a/0x890
[ 184.731944] RSP: 0018:ffffba8243c0fd90 EFLAGS: 00010246
[ 184.737880] RAX: 0000000000000000 RBX: 0000000000000000 RCX: 00000000000295d6
[ 184.746020] RDX: 00000000000295d5 RSI: 0000000000000001 RDI: ffff971a6418d400
[ 184.754121] RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
[ 184.762222] R10: ffff971a64c98a80 R11: ffff971a62a00e40 R12: ffff971a62a85500
[ 184.770325] R13: 0000000000020000 R14: ffff971a6418d400 R15: ffff971a6418d400
[ 184.778448] FS: 00007fe725a79700(0000) GS:ffff971a6ec00000(0000) knlGS:0000000000000000
[ 184.787644] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 184.794168] CR2: 0000000000000000 CR3: 000000025f365005 CR4: 00000000003606f0
[ 184.802318] Call Trace:
[ 184.805094] ? seq_read+0x281/0x3b0
[ 184.809068] seq_read+0xeb/0x3b0
[ 184.812735] full_proxy_read+0x4d/0x70
[ 184.817007] __vfs_read+0x23/0x120
[ 184.820870] vfs_read+0x91/0x130
[ 184.824538] SyS_read+0x42/0x90
[ 184.828106] entry_SYSCALL_64_fastpath+0x1a/0x7d
Fixes: dde634057da7 ("xhci: Fix use-after-free in xhci debugfs")
Cc: <stable@vger.kernel.org> # v4.15
Signed-off-by: Zhengjun Xing <zhengjun.xing@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When disabling a USB3 port the hub driver will set the port link state to
U3 to prevent "ejected" or "safely removed" devices that are still
physically connected from immediately re-enumerating.
If the device was really unplugged, then error messages were printed
as the hub tries to set the U3 link state for a port that is no longer
enabled.
xhci-hcd ee000000.usb: Cannot set link state.
usb usb8-port1: cannot disable (err = -32)
Don't print error message in xhci-hub if hub tries to set port link state
for a disabled port. Return -ENODEV instead which also silences hub driver.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For AMD Promontory xHCI host, although you can disable USB ports in
BIOS settings, those ports will be enabled anyway after you remove a
device on that port and re-plug it in again. It's a known limitation of
the chip. As a workaround we can clear the PORT_WAKE_BITS.
[commit and code comment rephrasing -Mathias]
Signed-off-by: Joe Lee <asmt.swfae@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order for ULPI PHYs to work, dwc3_phy_setup() and dwc3_ulpi_init()
must be doene before dwc3_core_get_phy().
commit 541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
broke this.
The other issue is that dwc3_core_get_phy() and dwc3_ulpi_init() should
be called only once during the life cycle of the driver. However,
as dwc3_core_init() is called during system suspend/resume it will
result in multiple calls to dwc3_core_get_phy() and dwc3_ulpi_init()
which is wrong.
Fix this by moving dwc3_ulpi_init() out of dwc3_phy_setup()
into dwc3_core_ulpi_init(). Use a flag 'ulpi_ready' to ensure that
dwc3_core_ulpi_init() is called only once from dwc3_core_init().
Use another flag 'phys_ready' to call dwc3_core_get_phy() only once from
dwc3_core_init().
Fixes: 541768b08a40 ("usb: dwc3: core: Call dwc3_core_get_phy() before initializing phys")
Fixes: f54edb539c11 ("usb: dwc3: core: initialize ULPI before trying to get the PHY")
Cc: linux-stable <stable@vger.kernel.org> # >= v4.13
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add the missing platform_device_put() before return from bdc_pci_probe()
in the platform_device_add_resources() error handling case.
Fixes: efed421a94e6 ("usb: gadget: Add UDC driver for Broadcom USB3.0 device controller IP BDC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We should call dwc2_hsotg_enqueue_setup() after properly
setting lx_state. Because it may cause error-out from
dwc2_hsotg_enqueue_setup() due to wrong value in lx_state.
Issue can be reproduced by loading driver while connected
A-Connector (start in A-HOST mode) then disconnect A-Connector
to switch to B-DEVICE.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
STSPHSERCVD (status phase received) interrupt should be
handled when EP0 is in DWC2_EP0_DATA_OUT state.
Sometimes STSPHSERCVD interrupt asserted , when EP0
is not in DATA_OUT state. Spurios interrupt.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In some cases device sending ZLP IN on non EP0 which
reassigning EP0 OUT descriptor pointer to that EP.
Dedicated for EP0 OUT descriptor multiple time re-used by
other EP while that descriptor already in use by EP0 OUT
for SETUP transaction. As result when SETUP packet received
BNA interrupt asserting.
In dwc2_hsotg_program_zlp() function dwc2_gadget_set_ep0_desc_chain()
must be called only for EP0.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Grigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Clang reports the following warning:
drivers/usb/gadget/udc/fsl_udc_core.c:1312:10: warning: address of array
'ep->name' will always evaluate to 'true' [-Wpointer-bool-conversion]
if (ep->name)
~~ ~~~~^~~~
It seems that the authors intention was to check if the ep has been
configured through struct_ep_setup. Check whether struct usb_ep name
pointer has been set instead.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This fixes an issue that a gadget driver (usb_f_fs) is possible to
stop rx transactions after the usb-dmac is used because the following
functions missed to set/check the "running" flag.
- usbhsf_dma_prepare_pop_with_usb_dmac()
- usbhsf_dma_pop_done_with_usb_dmac()
So, if next transaction uses pio, the usbhsf_prepare_pop() can not
start the transaction because the "running" flag is 0.
Fixes: 8355b2b3082d ("usb: renesas_usbhs: fix the behavior of some usbhs_pkt_handle")
Cc: <stable@vger.kernel.org> # v3.19+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
USB_GADGET_DUALSPEED was removed by commit 85b8614d7223 ("usb: gadget:
get rid of USB_GADGET_{DUAL,SUPER}SPEED"), but the USB_SNP_UDC_PLAT
symbol still selects it.
Remove the USB_GADGET_DUALSPEED select from USB_SNP_UDC_PLAT.
Discovered with the
https://github.com/ulfalizer/Kconfiglib/blob/master/examples/list_undefined.py
script.
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The FIFO/Queue type values are incorrect. Correct them according to
DWC_usb3 programming guide section 1.2.27 (or DWC_usb31 section 1.2.25).
Additionally, this patch includes ProtocolStatusQ and AuxEventQ types.
Fixes: cf6d867d3b57 ("usb: dwc3: core: add fifo space helper")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Driver is tracing usb_request after freeing it.
Fix it by changing the order.
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The USB cable state can change during suspend/resume
so be sure to check and update the extcon state.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In commit 2bfa0719ac2a ("usb: gadget: function: f_fs: pass
companion descriptor along") there is a pointer arithmetic
bug where the comp_desc is obtained as follows:
comp_desc = (struct usb_ss_ep_comp_descriptor *)(ds +
USB_DT_ENDPOINT_SIZE);
Since ds is a pointer to usb_endpoint_descriptor, adding
7 to it ends up going out of bounds (7 * sizeof(struct
usb_endpoint_descriptor), which is actually 7*9 bytes) past
the SS descriptor. As a result the maxburst value will be
read incorrectly, and the UDC driver will also get a garbage
comp_desc (assuming it uses it).
Since Felipe wrote, "Eventually, f_fs.c should be converted
to use config_ep_by_speed() like all other functions, though",
let's finally do it. This allows the other usb_ep fields to
be properly populated, such as maxpacket and mult. It also
eliminates the awkward speed-based descriptor lookup since
config_ep_by_speed() does that already using the ones found
in struct usb_function.
Fixes: 2bfa0719ac2a ("usb: gadget: function: f_fs: pass companion descriptor along")
Cc: stable@vger.kernel.org
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
During _ffs_func_bind(), the received descriptors are evaluated
to prepare for binding with the gadget in order to allocate
endpoints and optionally set up OS descriptors. However, the
high- and super-speed descriptors are only parsed based on
whether the gadget_is_dualspeed() and gadget_is_superspeed()
calls are true, respectively.
This is a problem in case a userspace program always provides
all of the {full,high,super,OS} descriptors when configuring a
function. Then, for example if a gadget device is not capable
of SuperSpeed, the call to ffs_do_descs() for the SS descriptors
is skipped, resulting in an incorrect offset calculation for
the vla_ptr when moving on to the OS descriptors that follow.
This causes ffs_do_os_descs() to fail as it is now looking at
the SS descriptors' offset within the raw_descs buffer instead.
_ffs_func_bind() should evaluate the descriptors unconditionally,
so remove the checks for gadget speed.
Fixes: f0175ab51993 ("usb: gadget: f_fs: OS descriptors support")
Cc: stable@vger.kernel.org
Co-Developed-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Mayank Rana <mrana@codeaurora.org>
Signed-off-by: Jack Pham <jackp@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Commit e93650994a95 ("usb: phy: mxs: add usb charger type detection")
causes the following kernel hang on i.MX28:
[ 2.207973] usbcore: registered new interface driver usb-storage
[ 2.235659] Unable to handle kernel NULL pointer dereference at virtual address 00000188
[ 2.244195] pgd = (ptrval)
[ 2.246994] [00000188] *pgd=00000000
[ 2.250676] Internal error: Oops: 5 [#1] ARM
[ 2.254979] Modules linked in:
[ 2.258089] CPU: 0 PID: 1 Comm: swapper Not tainted 4.15.0-rc8-next-20180117-00002-g75d5f21 #7
[ 2.266724] Hardware name: Freescale MXS (Device Tree)
[ 2.271921] PC is at regmap_read+0x0/0x5c
[ 2.275977] LR is at mxs_phy_charger_detect+0x34/0x1dc
mxs_phy_charger_detect() makes accesses to the anatop registers via regmap,
however i.MX23/28 do not have such registers, which causes a NULL pointer
dereference.
Fix the issue by doing a NULL check on the 'regmap' pointer.
Fixes: e93650994a95 ("usb: phy: mxs: add usb charger type detection")
Cc: <stable@vger.kernel.org> # v4.15
Reviewed-by: Li Jun <jun.li@nxp.com>
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Commit 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during
host bus-suspend/resume") updated suspend/resume routines to not
power_off and reinit PHYs/core for host mode.
It broke platforms that rely on DWC3 core to power_off PHYs to
enter low power state on system suspend.
Perform dwc3_core_exit/init only during host mode system_suspend/
resume to addresses power regression from above mentioned patch
and also allow USB session to stay connected across
runtime_suspend/resume in host mode. While at it also replace
existing checks for HOST only dr_mode with current_dr_role to
have similar core driver behavior for both Host-only and DRD+Host
configurations.
Fixes: 689bf72c6e0d ("usb: dwc3: Don't reinitialize core during host bus-suspend/resume")
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In this function, we init the USB2 and USB3 PHYs, but if soft reset
times out, we don't unwind this.
Noticed by inspection.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If there are multiple functions associated with a configuration, then
the UAC2 interfaces may not start at zero. Set the correct first
interface number in the association descriptor so that the audio
interfaces are enumerated correctly in this case.
Reviewed-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: John Keeping <john@metanate.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
DWC3 tracks TRB counter for each ep0 direction separately. In control
read transfer completion handler, the driver needs to reset the TRB
enqueue counter for ep0 IN direction. Currently the driver only resets
the TRB counter for control OUT endpoint. Check for the data direction
and properly reset the TRB counter from correct control endpoint.
Cc: stable@vger.kernel.org
Fixes: c2da2ff00606 ("usb: dwc3: ep0: don't use ep0in for transfers")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
There are 2 control endpoint structures for DWC3. However, the driver
only updates the OUT direction control endpoint structure during
ConnectDone event. DWC3 driver needs to update the endpoint max packet
size for control IN endpoint as well. If the max packet size is not
properly set, then the driver will incorrectly calculate the data
transfer size and fail to send ZLP for HS/FS 3-stage control read
transfer.
The fix is simply to update the max packet size for the ep0 IN direction
during ConnectDone event.
Cc: stable@vger.kernel.org
Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This patch fixes an issue that the renesas_usb3_remove() causes
NULL pointer dereference because the usb3_to_dev() macro will use
the gadget instance and it will be deleted before.
Fixes: cf06df3fae28 ("usb: gadget: udc: renesas_usb3: move pm_runtime_{en,dis}able()")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
dwc3_of_simple_dev_pm_ops has never been used since commit a0d8c4cfdf31
("usb: dwc3: of-simple: set dev_pm_ops"), but this commit has brought
and oops when unbind the device due this sequence:
dwc3_of_simple_remove
-> clk_disable ...
-> pm_runtime_put_sync
-> dwc3_of_simple_runtime_suspend
-> clk_disable (again)
This double call to clk_core_disable causes a kernel oops like this:
WARNING: CPU: 1 PID: 4022 at drivers/clk/clk.c:656 clk_core_disable+0x78/0x80
CPU: 1 PID: 4022 Comm: bash Not tainted 4.15.0-rc4+ #44
Hardware name: Google Kevin (DT)
pstate: 80000085 (Nzcv daIf -PAN -UAO)
pc : clk_core_disable+0x78/0x80
lr : clk_core_disable_lock+0x20/0x38
sp : ffff00000bbf3a90
...
Call trace:
clk_core_disable+0x78/0x80
clk_disable+0x1c/0x30
dwc3_of_simple_runtime_suspend+0x30/0x50
pm_generic_runtime_suspend+0x28/0x40
This patch fixes the unbalanced clk disable call by setting the num_clocks
variable to zero once the clocks were disabled.
Fixes: a0d8c4cfdf31 ("usb: dwc3: of-simple: set dev_pm_ops")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fixes: 23c35f48f5fb ("pinctrl: remove include file from <linux/device.h>")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
|
|
Pull USB/PHY updates from Greg KH:
"Here is the big USB and PHY driver update for 4.16-rc1.
Along with the normally expected XHCI, MUSB, and Gadget driver
patches, there are some PHY driver fixes, license cleanups, sysfs
attribute cleanups, usbip changes, and a raft of other smaller fixes
and additions.
Full details are in the shortlog.
All of these have been in the linux-next tree for a long time with no
reported issues"
* tag 'usb-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (137 commits)
USB: serial: pl2303: new device id for Chilitag
USB: misc: fix up some remaining DEVICE_ATTR() usages
USB: musb: fix up one odd DEVICE_ATTR() usage
USB: atm: fix up some remaining DEVICE_ATTR() usage
USB: move many drivers to use DEVICE_ATTR_WO
USB: move many drivers to use DEVICE_ATTR_RO
USB: move many drivers to use DEVICE_ATTR_RW
USB: misc: chaoskey: Use true and false for boolean values
USB: storage: remove old wording about how to submit a change
USB: storage: remove invalid URL from drivers
usb: ehci-omap: don't complain on -EPROBE_DEFER when no PHY found
usbip: list: don't list devices attached to vhci_hcd
usbip: prevent bind loops on devices attached to vhci_hcd
USB: serial: remove redundant initializations of 'mos_parport'
usb/gadget: Fix "high bandwidth" check in usb_gadget_ep_match_desc()
usb: gadget: compress return logic into one line
usbip: vhci_hcd: update 'status' file header and format
USB: serial: simple: add Motorola Tetra driver
CDC-ACM: apply quirk for card reader
usb: option: Add support for FS040U modem
...
|
|
Pull poll annotations from Al Viro:
"This introduces a __bitwise type for POLL### bitmap, and propagates
the annotations through the tree. Most of that stuff is as simple as
'make ->poll() instances return __poll_t and do the same to local
variables used to hold the future return value'.
Some of the obvious brainos found in process are fixed (e.g. POLLIN
misspelled as POLL_IN). At that point the amount of sparse warnings is
low and most of them are for genuine bugs - e.g. ->poll() instance
deciding to return -EINVAL instead of a bitmap. I hadn't touched those
in this series - it's large enough as it is.
Another problem it has caught was eventpoll() ABI mess; select.c and
eventpoll.c assumed that corresponding POLL### and EPOLL### were
equal. That's true for some, but not all of them - EPOLL### are
arch-independent, but POLL### are not.
The last commit in this series separates userland POLL### values from
the (now arch-independent) kernel-side ones, converting between them
in the few places where they are copied to/from userland. AFAICS, this
is the least disruptive fix preserving poll(2) ABI and making epoll()
work on all architectures.
As it is, it's simply broken on sparc - try to give it EPOLLWRNORM and
it will trigger only on what would've triggered EPOLLWRBAND on other
architectures. EPOLLWRBAND and EPOLLRDHUP, OTOH, are never triggered
at all on sparc. With this patch they should work consistently on all
architectures"
* 'misc.poll' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (37 commits)
make kernel-side POLL... arch-independent
eventpoll: no need to mask the result of epi_item_poll() again
eventpoll: constify struct epoll_event pointers
debugging printk in sg_poll() uses %x to print POLL... bitmap
annotate poll(2) guts
9p: untangle ->poll() mess
->si_band gets POLL... bitmap stored into a user-visible long field
ring_buffer_poll_wait() return value used as return value of ->poll()
the rest of drivers/*: annotate ->poll() instances
media: annotate ->poll() instances
fs: annotate ->poll() instances
ipc, kernel, mm: annotate ->poll() instances
net: annotate ->poll() instances
apparmor: annotate ->poll() instances
tomoyo: annotate ->poll() instances
sound: annotate ->poll() instances
acpi: annotate ->poll() instances
crypto: annotate ->poll() instances
block: annotate ->poll() instances
x86: annotate ->poll() instances
...
|
|
Pull siginfo cleanups from Eric Biederman:
"Long ago when 2.4 was just a testing release copy_siginfo_to_user was
made to copy individual fields to userspace, possibly for efficiency
and to ensure initialized values were not copied to userspace.
Unfortunately the design was complex, it's assumptions unstated, and
humans are fallible and so while it worked much of the time that
design failed to ensure unitialized memory is not copied to userspace.
This set of changes is part of a new design to clean up siginfo and
simplify things, and hopefully make the siginfo handling robust enough
that a simple inspection of the code can be made to ensure we don't
copy any unitializied fields to userspace.
The design is to unify struct siginfo and struct compat_siginfo into a
single definition that is shared between all architectures so that
anyone adding to the set of information shared with struct siginfo can
see the whole picture. Hopefully ensuring all future si_code
assignments are arch independent.
The design is to unify copy_siginfo_to_user32 and
copy_siginfo_from_user32 so that those function are complete and cope
with all of the different cases documented in signinfo_layout. I don't
think there was a single implementation of either of those functions
that was complete and correct before my changes unified them.
The design is to introduce a series of helpers including
force_siginfo_fault that take the values that are needed in struct
siginfo and build the siginfo structure for their callers. Ensuring
struct siginfo is built correctly.
The remaining work for 4.17 (unless someone thinks it is post -rc1
material) is to push usage of those helpers down into the
architectures so that architecture specific code will not need to deal
with the fiddly work of intializing struct siginfo, and then when
struct siginfo is guaranteed to be fully initialized change copy
siginfo_to_user into a simple wrapper around copy_to_user.
Further there is work in progress on the issues that have been
documented requires arch specific knowledge to sort out.
The changes below fix or at least document all of the issues that have
been found with siginfo generation. Then proceed to unify struct
siginfo the 32 bit helpers that copy siginfo to and from userspace,
and generally clean up anything that is not arch specific with regards
to siginfo generation.
It is a lot but with the unification you can of siginfo you can
already see the code reduction in the kernel"
* 'siginfo-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (45 commits)
signal/memory-failure: Use force_sig_mceerr and send_sig_mceerr
mm/memory_failure: Remove unused trapno from memory_failure
signal/ptrace: Add force_sig_ptrace_errno_trap and use it where needed
signal/powerpc: Remove unnecessary signal_code parameter of do_send_trap
signal: Helpers for faults with specialized siginfo layouts
signal: Add send_sig_fault and force_sig_fault
signal: Replace memset(info,...) with clear_siginfo for clarity
signal: Don't use structure initializers for struct siginfo
signal/arm64: Better isolate the COMPAT_TASK portion of ptrace_hbptriggered
ptrace: Use copy_siginfo in setsiginfo and getsiginfo
signal: Unify and correct copy_siginfo_to_user32
signal: Remove the code to clear siginfo before calling copy_siginfo_from_user32
signal: Unify and correct copy_siginfo_from_user32
signal/blackfin: Remove pointless UID16_SIGINFO_COMPAT_NEEDED
signal/blackfin: Move the blackfin specific si_codes to asm-generic/siginfo.h
signal/tile: Move the tile specific si_codes to asm-generic/siginfo.h
signal/frv: Move the frv specific si_codes to asm-generic/siginfo.h
signal/ia64: Move the ia64 specific si_codes to asm-generic/siginfo.h
signal/powerpc: Remove redefinition of NSIGTRAP on powerpc
signal: Move addr_lsb into the _sigfault union for clarity
...
|
|
Pick up urgent bug fix and resolve the conflict.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
Linus Torvalds
Bin Liu
Andreas Kemnade
Greg Kroah-Hartman
Dominik Bozek
James Hogan
Jack Stocker
AMAN DEEP
Peter Chen
Karsten Koop
Yoshihiro Shimoda
Shuah Khan
Shigeru Yoshida
Kristian Evensen
Zhengjun Xing
Mathias Nyman
Joe Lee
Roger Quadros
Wei Yongjun
Vardan Mikayelyan
Minas Harutyunyan
Stefan Agner
Ulf Magnusson
Thinh Nguyen
Manu Gautam
Jack Pham
Fabio Estevam
Brian Norris
John Keeping
Enric Balletbo i Serra
Stephen Rothwell
Thomas Gleixner