| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The immediately preceding gpio_direction_output() already set the value,
so there's no need to repeat it. This also prevents gpio_set_value() from
WARNing when the GPIO is sleepable (e.g. is on an I2C expander); the set
direction API is always sleepable, but plain set_value isn't.
Cc: <stable@vger.kernel.org> # v3.3
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1547) rearranges the Power Management parts of the
ehci-tegra driver to match the conventions used in other EHCI platform
drivers. In particular, the controller should not be powered down by
the root hub's suspend routine; the controller's power level should be
managed by the controller's own PM methods.
The end result of the patch is that the standard ehci_bus_suspend()
and ehci_bus_resume() methods can be used instead of special-purpose
routines. The driver now uses the standard dev_pm_ops methods instead
of legacy power management. Since there is no supported wakeup
mechanism for the controller, runtime suspend is forbidden by default
(this can be overridden via sysfs, if desired).
These adjustments are needed in order to make ehci-tegra compatible
with recent changes to the USB core. The core now checks the root
hub's status following bus suspend; if the controller is automatically
powered down during bus suspend then the check will fail and the root
hub will be resumed immediately. Doing the controller power-down in a
separate method avoids this problem.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb: fixes for v3.4-rc cycle
A few more fixes for v3.4-rc cycle.
It includes a couple of fixes to the ordering of the methods in udc-core.c.
Without these two patches, we will have issues when either unregistering a
gadget driver (triggered with dummy_hcd only) or issuing a device-initiated
disconnect through sysfs.
There's also a fix on dummy_hcd to not call ->pullup() from udc_stop() because
udc-core.c already handles that.
A fix to MUSB as promised, to kill the compile warnings regarding deprecated
interfaces. We are essentially dropping the __deprecated flag because it
doesn't look like we will ever be able to live without it when we consider the
amount of silicon issues we find on different MUSB instantiations.
A couple of other fixes are also available, one adding the missing transceiver
events to gpio_vbus and another adding a missing unregister call to MUSB's
davinci glue layer.
|
|
This patch (as1548) fixes a recently-introduced incompatibility
between the UDC core and the dummy-hcd driver. Commit
8ae8090c82eb407267001f75b3d256b3bd4ae691 (usb: gadget: udc-core: fix
asymmetric calls in remove_driver) moved the usb_gadget_udc_stop()
call in usb_gadget_remove_driver() below the usb_gadget_disconnect()
call.
As a result, usb_gadget_disconnect() gets called at a time when the
gadget driver believes it has been unbound but dummy-hcd believes
it has not. A nasty error ensues when dummy-hcd calls the gadget
driver's disconnect method a second time.
To fix the problem, this patch moves the gadget driver's unbind
notification after the usb_gadget_disconnect() call. Now nothing
happens between the two unbind notifications, so nothing goes wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
commit 6d258a4 (usb: gadget: udc-core: stop UDC on device-initiated
disconnect) introduced another case of asymmetric calls when issuing
a device-initiated disconnect. Fix it.
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch fixes a race whereby a pointer to a buffer
would be overwritten while the buffer was in use leading
to a double free and a memory leak. This causes crashes.
This bug was introduced in 2.6.34
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Tested-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1545) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers. Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.
After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state. Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.
The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep. Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.
This fixes Bugzilla #42728.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Andrey Rahmatullin <wrar@wrar.name>
Tested-by: Oleksij Rempel (fishor) <bug-track@fisher-privat.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The field is used to pass the UVC request data length, but can also be
used to signal an error when setting it to a negative value. Switch from
unsigned int to __s32.
Reported-by: Fernandez Gonzalo <gfernandez@copreci.es>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull "ARM: SoC fixes" from Olof Johansson:
* at91, ux500, imx, omap and bcmring:
- at91 fixes for =m driver build issues, irqdomain fixes and config
dependency fixes
- ux500 kconfig dependency fixes and a smp wakeup bugfix
- imx idle bugfix and build fix due to irq domain changes
- omap uart pinmux fixes, softreset regression revert and misc fixes
- bcmring build error regression fix
* ux500 and imx had some small defconfig updates in this branch
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (27 commits)
ARM: bcmring: fix UART declarations
ARM: imx: Fix imx5 idle logic bug
ARM: imx27-dt: Fix build due to removal of irq_domain_add_simple()
ARM: imx_v4_v5_defconfig: Add support for CONFIG_REGULATOR_FIXED_VOLTAGE
ARM: OMAP1: DMTIMER: fix broken timer clock source selection
ARM: OMAP: serial: Fix the ocp smart idlemode handling bug
ARM: OMAP2+: UART: Fix incorrect population of default uart pads
ARM: OMAP: sram: fix BUG in dpll code for !PM case
dmaengine: Kconfig: fix Atmel at_hdmac entry
USB: gadget/at91_udc: add gpio_to_irq() function to vbus interrupt
USB: ohci-at91: change annotations for probe/remove functions
leds-atmel-pwm.c: Make pwmled_probe() __devinit
ARM: at91: fix at91sam9261ek Ethernet dm9000 irq
ARM: at91: fix rm9200ek flash size
ARM: at91: remove empty at91_init_serial function
ARM: at91: fix typo in at91_pmc_base assembly declaration
ARM: at91: Export at91_matrix_base
ARM: at91: Export at91_pmc_base
ARM: at91: Export at91_ramc_base
ARM: at91: Export at91_st_base
...
|
|
Pull MFD fixes from Samuel Ortiz:
"We have 3 build fixes, a OMAP USB host PHY reset fix and the twl6040
conversion to an i2c driver. The latter may not sound like a fix but
the twl6040 MFD driver won't probe without it, triggering an OMAP4
audio regression."
* tag 'mfd-for-linus-3.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6:
mfd: Fix modular builds of rc5t583 regulator support
mfd: Fix asic3_gpio_to_irq
ARM: OMAP3: USB: Fix the EHCI ULPI PHY reset issue
mfd: Convert twl6040 to i2c driver, and separate it from twl core
mfd : Fix dbx500 compilation error
|
|
Fixed too small hardcoded timeout values for usb_control_msg
in driver for SiliconLabs cp210x-based usb-to-serial adapters.
Replaced with USB_CTRL_GET_TIMEOUT/USB_CTRL_SET_TIMEOUT.
Signed-off-by: Yuri Matylitski <ym@tekinsoft.com>
Acked-by: Kirill A. Shutemov <kirill@shutemov.name>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pullup() is already called properly by udc-core.c and
there's no need to call it from udc_stop(), in fact that
will cause issues.
Cc: stable@vger.kernel.org
Reviewed-by: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This call is not needed; the IRQ controller should (and does) set up
interrupts correctly. set_irq_flags() isn't exported to modules, to
this also fixes compilation of ehci-tegra.c as a module.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Current probing code is setting URB_NO_TRANSFER_DMA_MAP flag into a wrong urb
structure, and this causes BUG_ON with some USB host implementations.
This patch fixes the issue.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Removes allocation of coherent buffer for the control-request setup-packet
buffer from the yurex driver. Using coherent buffers for setup-packet is
obsolete and does not work with some USB host implementations.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Free the two previously allocated buffers before exiting the function in an
error case.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 28c56ea1431421dec51b7b229369e991481453df
(powerpc/usb: fix bug of kernel hang when initializing usb)
the kernel crashes on mpc5121e. mpc5121e doesn't have system interface
registers, accessing this register address space cause the machine check
exception and a kernel crash:
...
[ 1.294596] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.316491] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.337334] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 1.358548] Machine check in kernel mode.
[ 1.375917] Caused by (from SRR1=49030): Transfer error ack signal
[ 1.395505] Oops: Machine check, sig: 7 [#1]
[ 1.413113] MPC5121 ADS
[ 1.428718] Modules linked in:
[ 1.444841] NIP: c026efc4 LR: c0278b50 CTR: 00000000
[ 1.463342] REGS: df837ba0 TRAP: 0200 Not tainted (3.3.0-08839-gb5174fa)
[ 1.484083] MSR: 00049030 <EE,ME,IR,DR> CR: 42042022 XER: 20000000
[ 1.504099] TASK = df834000[1] 'swapper' THREAD: df836000
[ 1.509667] GPR00: 1c000000 df837c50 df834000 df9d74e0 00000003 00000010 00000000 00000000
[ 1.531650] GPR08: 00000020 00000000 c037cdd8 e1088000 22042028 1001a69c 00000000 00000000
[ 1.553762] GPR16: 1ffbce70 00000000 1fef5b28 1fef3e08 00000000 00000000 1ffcbc7c c045b264
[ 1.575824] GPR24: 0000008b 00000002 c04a7dd0 e1088000 df33c960 df9d74e0 00000000 df9d7400
[ 1.612295] NIP [c026efc4] ehci_fsl_setup_phy+0x110/0x124
[ 1.632454] LR [c0278b50] ehci_fsl_setup+0x29c/0x304
[ 1.652065] Call Trace:
[ 1.668923] [df837c50] [c0278a40] ehci_fsl_setup+0x18c/0x304 (unreliable)
[ 1.690332] [df837c70] [c025cba4] usb_add_hcd+0x1f0/0x66c
[ 1.710377] [df837cb0] [c0277ab8] ehci_fsl_drv_probe+0x180/0x308
[ 1.731322] [df837ce0] [c01fc7a8] platform_drv_probe+0x20/0x30
[ 1.752202] [df837cf0] [c01fb0ac] driver_probe_device+0x8c/0x214
[ 1.773491] [df837d10] [c01f956c] bus_for_each_drv+0x6c/0xa8
[ 1.794279] [df837d40] [c01fafdc] device_attach+0xb4/0xd8
[ 1.814574] [df837d60] [c01fa44c] bus_probe_device+0xa4/0xb4
[ 1.835343] [df837d80] [c01f87a8] device_add+0x52c/0x5dc
[ 1.855462] [df837dd0] [c01fcd58] platform_device_add+0x124/0x1d0
[ 1.876558] [df837df0] [c036dcec] fsl_usb2_device_register+0xa0/0xd4
[ 1.897512] [df837e10] [c036df28] fsl_usb2_mph_dr_of_probe+0x208/0x264
[ 1.918253] [df837e90] [c01fc7a8] platform_drv_probe+0x20/0x30
[ 1.938300] [df837ea0] [c01fb0ac] driver_probe_device+0x8c/0x214
[ 1.958511] [df837ec0] [c01fb2f0] __driver_attach+0xbc/0xc0
[ 1.978088] [df837ee0] [c01f9608] bus_for_each_dev+0x60/0x9c
[ 1.997589] [df837f10] [c01fab88] driver_attach+0x24/0x34
[ 2.016757] [df837f20] [c01fa744] bus_add_driver+0x1ac/0x274
[ 2.036339] [df837f50] [c01fb898] driver_register+0x88/0x150
[ 2.056052] [df837f70] [c01fcabc] platform_driver_register+0x68/0x78
[ 2.076650] [df837f80] [c0446500] fsl_usb2_mph_dr_driver_init+0x18/0x28
[ 2.097734] [df837f90] [c0003988] do_one_initcall+0x148/0x1b0
[ 2.117934] [df837fc0] [c042d89c] kernel_init+0xfc/0x190
[ 2.137667] [df837ff0] [c000d2c4] kernel_thread+0x4c/0x68
[ 2.157240] Instruction dump:
[ 2.174119] 90050004 4e800020 2f840003 419e0014 2f840004 409eff64 6400c000 4bffff5c
[ 2.196000] 64001000 7c0004ac 812b0500 0c090000 <4c00012c> 61290200 7c0004ac 912b0500
[ 2.218100] ---[ end trace 21659aedb84ad816 ]---
[ 2.237089]
[ 3.232940] Kernel panic - not syncing: Attempted to kill init! exitcode=0x00000007
[ 3.232954]
[ 3.271575] Rebooting in 1 seconds..
Check pdata->have_sysif_regs flag before accessing system interface
registers.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as1544) fixes a problem affecting some EHCI controllers.
They can generate interrupts whenever the STS_FLR status bit is turned
on, even though that bit is masked out in the Interrupt Enable
register.
Since the driver doesn't use STS_FLR anyway, the patch changes the
interrupt routine to clear that bit whenever it is set, rather than
leaving it alone.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-and-tested-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb_nop_xceiv_unregister is needed on failure of usb_get_transceiver, as
done in other error-handling code in the same function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Looks like we cannot live without that double_buffer_not_ok
flag due to many HW bugs this MUSB core has.
So, let's drop the __deprecated flag to avoid annoying
compile warnings.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch (as1542) changes the criterion ehci-hcd uses to tell when
it needs to resume the controller's root hub. A resume is needed when
a port status change is detected, obviously, but only if the root hub
is currently suspended.
Right now the driver tests whether the root hub is running, and that
is not the correct test. In particular, if the controller has died
then the root hub should not be restarted. In addition, some buggy
hardware occasionally requires the root hub to be running and
sending out SOF packets even while it is nominally supposed to be
suspended.
In the end, the test needs to be changed. Rather than checking whether
the root hub is currently running, the driver will now check whether
the root hub is currently suspended. This will yield the correct
behavior in all cases.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: Peter Chen <B29397@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These devices have a number of non serial interfaces as well. Use
the existing "Direct IP" blacklist to prevent binding to interfaces
which are handled by other drivers.
We also extend the "Direct IP" blacklist with with interfaces only
seen in "QMI" mode, assuming that these devices use the same
interface numbers for serial interfaces both in "Direct IP" and in
"QMI" mode.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A large `nents' from userspace could overflow the allocation size,
leading to memory corruption.
| alloc_sglist()
| usbtest_ioctl()
Use kmalloc_array() to avoid the overflow.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoid overflowing context.count = param->sglen * param->iterations,
where both `sglen' and `iterations' are from userspace.
| test_ctrl_queue()
| usbtest_ioctl()
Keep -EOPNOTSUPP for error code.
Signed-off-by: Xi Wang <xi.wang@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch (as154) fixes a self-deadlock that occurs when userspace
writes to the bConfigurationValue sysfs attribute for a hub with
children. The task tries to lock the bandwidth_mutex at a time when
it already owns the lock:
The attribute's method calls usb_set_configuration(),
which calls usb_disable_device() with the bandwidth_mutex
held.
usb_disable_device() unregisters the existing interfaces,
which causes the hub driver to be unbound.
The hub_disconnect() routine calls hub_quiesce(), which
calls usb_disconnect() for each of the hub's children.
usb_disconnect() attempts to acquire the bandwidth_mutex
around a call to usb_disable_device().
The solution is to make usb_disable_device() acquire the mutex for
itself instead of requiring the caller to hold it. Then the mutex can
cover only the bandwidth deallocation operation and not the region
where the interfaces are unregistered.
This has the potential to change system behavior slightly when a
config change races with another config or altsetting change. Some of
the bandwidth released from the old config might get claimed by the
other config or altsetting, make it impossible to restore the old
config in case of a failure. But since we don't try to recover from
config-change failures anyway, this doesn't matter.
[This should be marked for stable kernels that contain the commit
fccf4e86200b8f5edd9a65da26f150e32ba79808 "USB: Free bandwidth when
usb_disable_device is called."
That commit was marked for stable kernels as old as 2.6.32.]
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Now that we are using irqdomains, we need to convert GPIO pins to Linux
IRQ numbers using the gpio_to_irq() function.
This call is added to request/free_irq calls.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: linux-usb@vger.kernel.org
|
|
Add __devinit and __devexit on *_probe() and *_remove() functions
with proper modification of struct platform_driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
|
|
It is observed that the echi ports of 3430 sdp board
are not working due to the random timing of programming
the associated GPIOs of the ULPI PHYs of the EHCI for reset.
If the PHYs are reset at during usbhs core driver, host ports will
not work because EHCI driver is loaded after the resetting PHYs.
The PHYs should be in reset state while initializing the EHCI
controller.
The code which does the GPIO pins associated with the PHYs
are programmed to reset is moved from the USB host core driver
to EHCI driver.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Reviewed-by: Partha Basak <parthab@india.ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
usb: fixes for v3.4-rc cycle
Here are the fixes I have queued for v3.4-rc cycle so far.
It includes fixes on many of the gadget drivers and a few
of the UDC controller drivers.
For musb we have a fix for a kernel oops when unloading
omap2430.ko glue layer, proper error checking for pm_runtime_*,
fix for the ULPI transfer block, and a bug fix in musb_cleanup_urb
routine.
For s3c-hsotg we have mostly FIFO-related fixes (proper TX FIFO
allocation, TX FIFO corruption fix in DMA mode) but also a couple
of minor fixes (fixing maximum packet size for ep0 and fix for
big transfers with DMA).
For the dwc3 driver we have a memory leak fix, a very important
fix for USB30CV with SetFeature tests and the hability to handle
ep0 requests bigger than wMaxPacketSize.
On top of that there's a bunch of gadget driver minor fixes adding
proper section annotations, and fixing up the sysfs interface for
doing device-initiated connect/disconnect and so on.
All patches have been pending on the mailing list for quite a while
and look good for your for-linus branch.
|
|
This patch (as1539) fixes a minor bug in the mass-storage gadget
drivers. When an unknown command is received, the error code sent
back is "Invalid Field in CDB" rather than "Invalid Command". This is
because the bitmask of CDB bytes allowed to be nonzero is incorrect.
When handling an unknown command, we don't care which command bytes
are nonzero. All the bits in the mask should be set, not just eight
of them.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <Michal Nazarewicz <mina86@mina86.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Commit 9ad63986c606 (pda_power: Add support for using otg transceiver events)
converted the pda-power driver to use otg events to determine the status
of the power supply.
As gpio-vbus didn't use otg events until now, this change breaks setups
of pda-power with a gpio-vbus transceiver.
This patch adds the necessary otg events and notifiers to gpio-vbus.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Dima Zavin <dima@android.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Re-define XHCI_LEGACY_DISABLE_SMI and used it in right way. All SMI enable
bits will be cleared to zero and flag bits 29:31 are also cleared to zero.
Other bits should be presvered as Table 146.
This patch should be backported to kernels as old as 2.6.31.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
The caller is allowed to specify the GFP flags for these functions.
We should prefer their flags unless we have good reason. For
example, if we take a spin_lock ourselves we'd need to use
GFP_ATOMIC. But in this case it's safe to use the callers GFP
flags.
The callers all pass GFP_ATOMIC here, so this change doesn't affect
how the kernel behaves but we may add other callers later and this
is a cleanup.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
The suspend operation of VIA xHCI host have some issues and
hibernate operation works fine, so The XHCI_RESET_ON_RESUME
quirk is added for it.
This patch should base on "xHCI: Don't write zeroed pointer
to xHC registers" that is released by Sarah. Otherwise, the
host system error will ocurr in the hibernate operation
process.
This should be backported to stable kernels as old as 2.6.37,
that contain the commit c877b3b2ad5cb9d4fe523c5496185cc328ff3ae9
"xhci: Add reset on resume quirk for asrock p67 host".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
When the Seagate Goflex USB3.0 device is attached to VIA xHCI
host, sometimes the device will downgrade mode to high speed.
By the USB analyzer, I found the device finished the link
training process and worked at superspeed mode. But the device
descriptor got from the device shows the device works at 2.1.
It is very strange and seems like the device controller of
Seagate Goflex has a little confusion.
The first 8 bytes of device descriptor should be:
12 01 00 03 00 00 00 09
But the first 8 bytes of wrong device descriptor are:
12 01 10 02 00 00 00 40
The wrong device descriptor caused the initialization of mass
storage failed. After a while, the device would be recognized
as a high speed device and works fine.
This patch will warm reset the device to fix the issue after
finding the bcdUSB field of device descriptor isn't 0x0300
but the speed mode of device is superspeed.
This patch should be backported to kernels as old as 3.2, or ones that
contain the commit 75d7cf72ab9fa01dc70877aa5c68e8ef477229dc "usbcore:
refine warm reset logic".
Signed-off-by: Elric Fu <elricfu1@gmail.com>
Acked-by: Andiry Xu <Andiry.Xu@amd.com>
Acked-by: Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
The xHCI 1.0 spec errata released on June 13, 2011, changes the ordering
that the xHCI registers are saved and restored in. It moves the
interrupt pending (IMAN) and interrupt control (IMOD) registers to be
saved and restored last. I believe that's because the host controller
may attempt to fetch the event ring table when interrupts are
re-enabled. Therefore we need to restore the event ring registers
before we re-enable interrupts.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI: PCI power
management implementation"
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
|
|
The xhci_save_registers() function saved the event ring dequeue pointer
in the s3 register structure, but xhci_restore_registers() never
restored it. No other code in the xHCI successful resume path would
ever restore it either. Fix that.
This should be backported to kernels as old as 2.6.37, that contain the
commit 5535b1d5f8885695c6ded783c692e3c0d0eda8ca "USB: xHCI: PCI power
management implementation".
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: Andiry Xu <andiry.xu@amd.com>
Cc: stable@vger.kernel.org
|
|
When xhci_mem_cleanup() is called, we can't be sure if the xHC is
actually halted. We can ask the xHC to halt by writing to the RUN bit
in the command register, but that might timeout due to a HW hang.
If the host controller is still running, we should not write zeroed
values to the event ring dequeue pointers or base tables, the DCBAA
pointers, or the command ring pointers. Eric Fu reports his VIA VL800
host accesses the event ring pointers after a failed register restore on
resume from suspend. The hypothesis is that the host never actually
halted before the register write to change the event ring pointer to
zero.
Remove all writes of zeroed values to pointer registers in
xhci_mem_cleanup(). Instead, make all callers of the function reset the
host controller first, which will reset those registers to zero.
xhci_mem_init() is the only caller that doesn't first halt and reset the
host controller before calling xhci_mem_cleanup().
This should be backported to kernels as old as 2.6.32.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Tested-by: Elric Fu <elricfu1@gmail.com>
Cc: stable@vger.kernel.org
|
|
Eric Fu reports a problem with his VIA host controller fetching a zeroed
event ring pointer on resume from suspend. The host should have been
halted, but we can't be sure because that code ignores the return value
from xhci_halt(). Print a warning when the host controller refuses to
halt within XHCI_MAX_HALT_USEC (currently 16 seconds).
(Update: it turns out that the VIA host controller is reporting a halted
state when it fetches the zeroed event ring pointer. However, we still
need this warning for other host controllers.)
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
While we're at that, define IMAN bitfield to aid readability.
The interrupt enable bit should be set once on driver init, and we
shouldn't need to continually re-enable it. Commit c21599a3 introduced
a read of the irq_pending register, and that allows us to preserve the
state of the IE bit. Before that commit, we were blindly writing 0x3 to
the register.
This patch should be backported to kernels as old as 2.6.36, or ones
that contain the commit c21599a36165dbc78b380846b254017a548b9de5 "USB:
xhci: Reduce reads and writes of interrupter registers".
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org
|
|
xhci_unregister_pci() is called in xhci_hcd_init().
Signed-off-by: Gerard Snitselaar <dev@snitselaar.org>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Correct the print of HSEE of USBCMD in xhci-dbg.c.
Signed-off-by: Alex He <alex.he@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
|
|
Fix race between probe and open by making sure that the disconnected
flag is not cleared until all ports have been registered.
A call to tty_open while probe is running may get a reference to the
serial structure in serial_install before its ports have been
registered. This may lead to usb_serial_core calling driver open before
port is fully initialised.
With ftdi_sio this result in the following NULL-pointer dereference as
the private data has not been initialised at open:
[ 199.698286] IP: [<f811a089>] ftdi_open+0x59/0xe0 [ftdi_sio]
[ 199.698297] *pde = 00000000
[ 199.698303] Oops: 0000 [#1] PREEMPT SMP
[ 199.698313] Modules linked in: ftdi_sio usbserial
[ 199.698323]
[ 199.698327] Pid: 1146, comm: ftdi_open Not tainted 3.2.11 #70 Dell Inc. Vostro 1520/0T816J
[ 199.698339] EIP: 0060:[<f811a089>] EFLAGS: 00010286 CPU: 0
[ 199.698344] EIP is at ftdi_open+0x59/0xe0 [ftdi_sio]
[ 199.698348] EAX: 0000003e EBX: f5067000 ECX: 00000000 EDX: 80000600
[ 199.698352] ESI: f48d8800 EDI: 00000001 EBP: f515dd54 ESP: f515dcfc
[ 199.698356] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[ 199.698361] Process ftdi_open (pid: 1146, ti=f515c000 task=f481e040 task.ti=f515c000)
[ 199.698364] Stack:
[ 199.698368] f811a9fe f811a9e0 f811b3ef 00000000 00000000 00001388 00000000 f4a86800
[ 199.698387] 00000002 00000000 f806e68e 00000000 f532765c f481e040 00000246 22222222
[ 199.698479] 22222222 22222222 22222222 f5067004 f5327600 f5327638 f515dd74 f806e6ab
[ 199.698496] Call Trace:
[ 199.698504] [<f806e68e>] ? serial_activate+0x2e/0x70 [usbserial]
[ 199.698511] [<f806e6ab>] serial_activate+0x4b/0x70 [usbserial]
[ 199.698521] [<c126380c>] tty_port_open+0x7c/0xd0
[ 199.698527] [<f806e660>] ? serial_set_termios+0xa0/0xa0 [usbserial]
[ 199.698534] [<f806e76f>] serial_open+0x2f/0x70 [usbserial]
[ 199.698540] [<c125d07c>] tty_open+0x20c/0x510
[ 199.698546] [<c10e9eb7>] chrdev_open+0xe7/0x230
[ 199.698553] [<c10e48f2>] __dentry_open+0x1f2/0x390
[ 199.698559] [<c144bfec>] ? _raw_spin_unlock+0x2c/0x50
[ 199.698565] [<c10e4b76>] nameidata_to_filp+0x66/0x80
[ 199.698570] [<c10e9dd0>] ? cdev_put+0x20/0x20
[ 199.698576] [<c10f3e08>] do_last+0x198/0x730
[ 199.698581] [<c10f4440>] path_openat+0xa0/0x350
[ 199.698587] [<c10f47d5>] do_filp_open+0x35/0x80
[ 199.698593] [<c144bfec>] ? _raw_spin_unlock+0x2c/0x50
[ 199.698599] [<c10ff110>] ? alloc_fd+0xc0/0x100
[ 199.698605] [<c10f0b72>] ? getname_flags+0x72/0x120
[ 199.698611] [<c10e4450>] do_sys_open+0xf0/0x1c0
[ 199.698617] [<c11fcc08>] ? trace_hardirqs_on_thunk+0xc/0x10
[ 199.698623] [<c10e458e>] sys_open+0x2e/0x40
[ 199.698628] [<c144c990>] sysenter_do_call+0x12/0x36
[ 199.698632] Code: 85 89 00 00 00 8b 16 8b 4d c0 c1 e2 08 c7 44 24 14 88 13 00 00 81 ca 00 00 00 80 c7 44 24 10 00 00 00 00 c7 44 24 0c 00 00 00 00 <0f> b7 41 78 31 c9 89 44 24 08 c7 44 24 04 00 00 00 00 c7 04 24
[ 199.698884] EIP: [<f811a089>] ftdi_open+0x59/0xe0 [ftdi_sio] SS:ESP 0068:f515dcfc
[ 199.698893] CR2: 0000000000000078
[ 199.698925] ---[ end trace 77c43ec023940cff ]---
Reported-and-tested-by: Ken Huang <csuhgw@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
usb: gadget: eliminate NULL pointer dereference (bugfix)
This patch fixes a bug which causes NULL pointer dereference in
ffs_ep0_ioctl. The bug happens when the FunctionFS is not bound (either
has not been bound yet or has been bound and then unbound) and can be
reproduced with running the following commands:
$ insmod g_ffs.ko
$ mount -t functionfs func /dev/usbgadget
$ ./null
where null.c is:
#include <fcntl.h>
#include <linux/usb/functionfs.h>
int main(void)
{
int fd = open("/dev/usbgadget/ep0", O_RDWR);
ioctl(fd, FUNCTIONFS_CLEAR_HALT);
return 0;
}
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch removes the non-required spinlock acquire/release calls on
'queue->irqlock' from 'uvc_queue_next_buffer' routine.
This routine is called from 'video->encode' function (which translates to
either 'uvc_video_encode_bulk' or 'uvc_video_encode_isoc') in 'uvc_video.c'.
As, the 'video->encode' routines are called with 'queue->irqlock' already held,
so acquiring a 'queue->irqlock' again in 'uvc_queue_next_buffer' routine causes
a spin lock recursion.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
It is crucial to assign each req->context value to struct rndis.
The problem happens for multi function gadget (g_multi) when multiple
functions are calling common usb_composite_dev control request.
It might happen that *_setup method from one usb function will
alter some fields of this common request issued by other USB
function.
Signed-off-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
pm_runtime_get_sync returns a signed integer. In case of errors
it returns a negative value. This patch fixes the error check
by making it signed instead of unsigned thus preventing register
access if get_sync_fails. Also passes the error cause to the
debug message.
Cc: stable@vger.kernel.org
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
During modprobe of gadget driver, pullup is called after
udc_start. In order to make the exit path symmetric when
removing a gadget driver, call pullup before ->udc_stop.
This is needed to avoid issues with PM where udc_stop
disables the module completely (put IP in reset state,
cut functional and interface clocks, and so on), which
prevents us from accessing the IP's address space,
thus creating the possibility of an abort exception
when we try to access IP's address space after clocks
are off.
Cc: stable@vger.kernel.org
Signed-off-by: Partha Basak <p-basak2@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
pm_runtime_enable is being called after omap2430_musb_init. Hence
pm_runtime_get_sync in omap2430_musb_init does not have any effect (does
not enable clocks) resulting in a crash during register access. It is
fixed here.
Cc: stable@vger.kernel.org # v3.0, v3.1, v3.2, v3.3
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
musb can be suspended at the time some other driver wants to do ulpi
transfers using usb_phy_io_* functions, and that can cause data abort,
as it happened with isp1704_charger:
http://article.gmane.org/gmane.linux.kernel/1226122
Add pm_runtime to ulpi functions to rectify this. This also adds io_dev
to usb_phy so that pm_runtime_* functions can be used.
Cc: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
Stephen Warren
Alan Stern
Greg Kroah-Hartman
Felipe Balbi
Oliver Neukum
Laurent Pinchart
Linus Torvalds
Yuri Matylitski
Tomoki Sekiyama
Julia Lawall
Anatolij Gustschin
Bjørn Mork
Xi Wang
Nicolas Ferre
Keshava Munegowda
Heiko Stübner
Alex He
Dan Carpenter
Elric Fu
Sarah Sharp
Gerard Snitselaar
Johan Hovold
Andrzej Pietrasiewicz
Bhupesh Sharma
Lukasz Majewski
Shubhrajyoti D
Kishon Vijay Abraham I
Grazvydas Ignotas