| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
pratyush.anand@st.com email-id doesn't exist anymore as I have left the
company. Replace ST's id with pratyush.anand@gmail.com.
Signed-off-by: Pratyush Anand <pratyush.anand@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull SCSI updates from James Bottomley:
"This is the usual grab bag of driver updates (lpfc, hpsa,
megaraid_sas, cxgbi, be2iscsi) plus an assortment of minor updates.
There is also one new driver: the Cisco snic. The advansys driver has
been rewritten to get rid of the warning about converting it to the
DMA API, the tape statistics patch got in and finally, there's a
resuffle of SCSI header files to separate more cleanly initiator from
target mode (and better share the common definitions)"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (156 commits)
snic: driver for Cisco SCSI HBA
qla2xxx: Fix indentation
qla2xxx: Comment out unreachable code
fusion: remove dead MTRR code
advansys: fix compilation errors and warnings when CONFIG_PCI is not set
mptsas: fix depth param in scsi_track_queue_full
megaraid: fix irq setup process regression
lpfc: Update version to 10.7.0.0 for upstream patch set.
lpfc: Fix to drop PLOGIs from fabric node till LOGO processing completes
lpfc: Fix scsi task management error message.
lpfc: Fix cq_id masking problem.
lpfc: Fix scsi prep dma buf error.
lpfc: Add support for using block multi-queue
lpfc: Devices are not discovered during takeaway/giveback testing
lpfc: Fix vport deletion failure.
lpfc: Check for active portpeerbeacon.
lpfc: Update driver version for upstream patch set 10.6.0.1.
lpfc: Change buffer pool empty message to miscellaneous category
lpfc: Fix incorrect log message reported for empty FCF record.
lpfc: Fix rport leak.
...
|
|
Turn
d_path(&file->f_path, ...);
into
file_path(file, ...);
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Pull trivial tree updates from Jiri Kosina:
"As usual, mostly comment, kerneldoc and printk() fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
lpfc: Grammar s/an negative/a negative/
ARM: lib/lib1funcs.S: fix typo s/substractions/subtractions/
cx25821: cx25821-medusa-reg.h: fix 0x0x prefix
lib: crc-itu-t.[ch] fix 0x0x prefix in integer constants
rapidio: Fix kerneldoc and comment
qla4xxx: Fix printk() in qla4_83xx_read_reset_template() and qla4_83xx_pre_loopback_config()
treewide: Kconfig: fix wording / spelling
usb/serial: fix grammar in Kconfig help text for FTDI_SIO
megaraid_sas: fix kerneldoc
netfilter: ebtables: fix comment grammar
drm/radeon: fix comment
isdn: fix grammar in comment
ARM: KVM: fix comment
|
|
Pull HID updates from Jiri Kosina:
- spurious power/wakeup sysfs files removal for I2C-HID devices, from
Andrew Duggan
- Logitech M560 support, from Goffredo Baroncelli
- a lot of housekeeping cleanups to hid-lg4ff driver, from Michal Maly
- improved support for Plantronics devices, from Terry Junge
- Sony Motion Controller and Navigation Controller support and
subsequent cleanups of hid-sony driver, from Frank Praznik and Simon
Wood
- HW support improvements to the Wacom driver, from Jason Gerecke and
Ping Cheng
- assorted small cleanups and device ID additions all over the place
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (69 commits)
HID: cypress: use swap() in cp_report_fixup()
HID: microsoft: Add Surface Power Cover
HID: hid-sony: Fix report descriptor for Navigation Controller
HID: hid-sony: Navigation controller only has 1 LED and no rumble
HID: hid-sony: Add BT support for Navigation Controller
HID: wacom: Introduce new 'touch_input' device
HID: wacom: Split apart 'wacom_setup_pentouch_input_capabilites'
HID: wacom: Introduce a new WACOM_DEVICETYPE_PAD device_type
HID: wacom: Treat features->device_type values as flags
HID: wacom: Simplify 'wacom_update_name'
HID: rmi: Disable populating F30 when the touchpad has physical buttons
HID: plantronics: Update to map volume up/down controls
HID: sony: PS Move fix report descriptor
HID: sony: PS3 Move enable LEDs and Rumble via BT
HID: sony: Add support PS3 Move Battery via BT
HID: sony: Add quirk for MOTION_CONTROLLER_BT
HID: sony: Support PS3 Move Controller when connected via Bluetooth
HID: i2c-hid: Do not set the ACPI companion field in the HID device
usb, HID: Remove Vernier devices from lsusb and hid_ignore_list
HID: hidpp: Add driver for mouse logitech M560
...
|
|
Add a "param_lock" mutex to each module, and update params.c to use
the correct built-in or module mutex while locking kernel params.
Remove the kparam_block_sysfs_r/w() macros, replace them with direct
calls to kernel_param_[un]lock(module).
The kernel param code currently uses a single mutex to protect
modification of any and all kernel params. While this generally works,
there is one specific problem with it; a module callback function
cannot safely load another module, i.e. with request_module() or even
with indirect calls such as crypto_has_alg(). If the module to be
loaded has any of its params configured (e.g. with a /etc/modprobe.d/*
config file), then the attempt will result in a deadlock between the
first module param callback waiting for modprobe, and modprobe trying to
lock the single kernel param mutex to set the new module's param.
This fixes that by using per-module mutexes, so that each individual module
is protected against concurrent changes in its own kernel params, but is
not blocked by changes to other module params. All built-in modules
continue to use the built-in mutex, since they will always be loaded at
runtime and references (e.g. request_module(), crypto_has_alg()) to them
will never cause load-time param changing.
This also simplifies the interface used by modules to block sysfs access
to their params; while there are currently functions to block and unblock
sysfs param access which are split up by read and write and expect a single
kernel param to be passed, their actual operation is identical and applies
to all params, not just the one passed to them; they simply lock and unlock
the global param mutex. They are replaced with direct calls to
kernel_param_[un]lock(THIS_MODULE), which locks THIS_MODULE's param_lock, or
if the module is built-in, it locks the built-in mutex.
Suggested-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Dan Streetman <ddstreet@ieee.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
Conflicts:
drivers/hid/wacom_wac.c
|
|
The Octeon OHCI is now supported by the ohci-platform driver, and
USB_OCTEON_OHCI is marked as deprecated. However, it is currently
still necessary to enable it in order to select
USB_OHCI_BIG_ENDIAN_MMIO. Make CPU_CAVIUM_OCTEON select that as well,
so that USB_OCTEON_OHCI is really obsolete.
The old ohci-octeon and ehci-octeon drivers also only enabled big-endian
MMIO in case the CPU was big-endian. Make the selections of
USB_EHCI_BIG_ENDIAN_MMIO and USB_OHCI_BIG_ENDIAN_MMIO conditional, to
match this.
Fixes: 2193dda5eec6 ("USB: host: Remove ehci-octeon and ohci-octeon drivers")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-mips@linux-mips.org
Cc: David Daney <david.daney@cavium.com>
Cc: Chandrakala Chavva <cchavva@caviumnetworks.com>
Cc: Paul Martin <paul.martin@codethink.co.uk>
Patchwork: https://patchwork.linux-mips.org/patch/10178/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This patch drops unnecessary target_core_fabric_ops parameter usage
for core_tpg_register() during fabric driver TFO->fabric_make_tpg()
se_portal_group creation callback execution.
Instead, use the existing se_wwn->wwn_tf->tf_ops pointer to ensure
fabric driver is really using the same TFO provided at module_init
time.
Also go ahead and drop the forward TFO declarations tree-wide, and
handling the special case for iscsi-target discovery TPG.
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The USB_DWC3_ULPI Kconfig entry uses a UTF-8 non-breaking space (0xca20)
instead of a regular ASCII space (0x20). Commit 2e0d737fc76f ("kconfig:
don't silently ignore unhandled characters") exposes this by warning
about unhandled characters.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch just redefine the unique id of supported external connectors without
'enum extcon' type. Because unique id would be used on devictree file(*.dts) to
indicate the specific external connectors like key number of input framework.
So, I have the plan to move this definitions to following header file which
includes the unique id of supported external connectors.
- include/dt-bindings/extcon/extcon.h
Fixes: 2a9de9c0f08d ("extcon: Use the unique id for external connector instead of string")
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Peter writes:
USB Chipidea update for v4.2-rc1
Just a minor change for code style
|
|
The Marvell 28nm HSIC PHY requires the port to be forced to HS mode after
the port power is applied. This is done using the test mode in the PORTSC
register.
As HSIC is always HS, this work-around should be safe to do with all HSIC
PHYs and has been tested on i.MX6S.
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, ci_default_pdata is common to all instances of the driver and
gets modified by the core driver code. This is bad if there are multiple
instances of the device with different settings such as the phy type. Fix
this by making a copy of the default platform_data.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Peter Chen <Peter.Chen@freescale.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of manually handling the frees use devm. There was also a free
missing in the unregister call which is not needed with devm.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch makes bcma_hcd_create_pdev() not return NULL, but a prober
error code in case of an error.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
isp1760_ep_alloc_request allocates a structure with kzalloc without checking
for NULL and then returns a pointer to one of the structure fields. As the
field happens to be the first in the structure the caller can properly check
for NULL, but this is risky if the structure layout is changed later. Add an
explicit NULL check for the kzalloc return value
Detected with smatch static analysis:
drivers/usb/isp1760/isp1760-udc.c:816 isp1760_ep_alloc_request()
error: potential null dereference 'req'. (kzalloc returns null)
[ thanks to Laurent Pinchart for improved commit message ]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ATOL FPrint fiscal printers require usb_clear_halt to be executed
to work properly. Add quirk to fix the issue.
Signed-off-by: Alexey Sokolov <sokolov@7pikes.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This resolves a merge issue in musb_core.c and we want the fixes that
were in Linus's tree in this branch as well for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove unneeded semicolon.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/semicolon.cocci.
More information about semantic patching is available at
http://coccinelle.lip6.fr/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Johan writes:
USB-serial fixes for v4.1-rc7
Here are a couple of new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Johan writes:
USB-serial updates for v4.2-rc1
Just a minor clean up of mos7840 this time.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Added the USB serial device ID for the HubZ dual ZigBee
and Z-Wave radio dongle.
Signed-off-by: John D. Blair <johnb@candicontrols.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Kishon writes:
phy: for 4.2 merge window
*) new Broadcom SATA3 PHY driver for Broadcom STB SoCs
*) new phy API to get PHY by index which is used in EHCI and
OHCI controller drivers
*) support specifying supply at port level used for multi-port PHYs
*) sparse warning fixes in miphy PHYs
*) fix pm_runtime issues in twl4030 driver
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Only include SCSI initiator header files in target code that needs
these header files, namely the SCSI pass-through code and the tcm_loop
driver. Change SCSI_SENSE_BUFFERSIZE into TRANSPORT_SENSE_BUFFER in
target code because the former is intended for initiator code and the
latter for target code. With this patch the only initiator include
directives in target code that remain are as follows:
$ git grep -nHE 'include .scsi/(scsi.h|scsi_host.h|scsi_device.h|scsi_cmnd.h)' drivers/target drivers/infiniband/ulp/{isert,srpt} drivers/usb/gadget/legacy/tcm_*.[ch] drivers/{vhost,xen} include/{target,trace/events/target.h}
drivers/target/loopback/tcm_loop.c:29:#include <scsi/scsi.h>
drivers/target/loopback/tcm_loop.c:31:#include <scsi/scsi_host.h>
drivers/target/loopback/tcm_loop.c:32:#include <scsi/scsi_device.h>
drivers/target/loopback/tcm_loop.c:33:#include <scsi/scsi_cmnd.h>
drivers/target/target_core_pscsi.c:39:#include <scsi/scsi_device.h>
drivers/target/target_core_pscsi.c:40:#include <scsi/scsi_host.h>
drivers/xen/xen-scsiback.c:52:#include <scsi/scsi_host.h> /* SG_ALL */
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Recently we purchased the Rigol DS6104 and when I try to operate it from
my Linux pc, everything works well with the default usbtmc driver,
except when I want to download a big datachunk like a screenshot. This
bitmapfile has a size of 1152054 bytes but I receive a smaller file and
no new packets can be read.
When I took a look at the driver source, I found this "Rigol quirk" and
I added the id of the new DS series oscilloscopes to this list. I
compiled it and loaded the new driver and now everything seems to work
fine.
Signed-off-by: Teunis van Beelen <teuniz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Felipe writes:
usb: patches for v4.2 merge window
- dwc2 adds hibernation support
- preparation for sunxi glue to musb driver
- new ULPI bus
- new ULPI PHY driver for TUSB1210
- musb patches to support multiple DMA engines on same binary
- support for R-Car E2 on renesas_usbhs
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use the timer API function setup_timer instead of structure field
assignments to initialize a timer.
A simplified version of the Coccinelle semantic patch that performs
this transformation is as follows:
@change@
expression e1, e2, e3, e4, a, b;
@@
-init_timer(&e1);
+setup_timer(&e1, a, b);
... when != a = e2
when != b = e3
-e1.function = a;
... when != b = e4
-e1.data = b;
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Removes Vernier Software & Technology devices from the ldusb
driver and the hid_ignore_list table of the usbhid driver in the
Linux tree. These devices will now be supported via the hidraw
driver.
A user space driver for these devices will be found in the
Go! Software Development Kit from Vernier at
http://www.vernier.com/downloads/software-development-kits/go-sdk/.
These devices are also be supported by the LabQuest2 standalone
interface shown at http://www.vernier.com/products/interfaces/labq2/
and the LoggerPro for Linux software shown at
http://www.vernier.com/downloads/logger-pro-linux/.
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
'0' is now used as the default cmd_per_lun value,
so there's no need to explicitly set it to '1' in the
host template.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Fix compilation error in fsl ehci drv because ehci_reset()
and ehci_adjust_port_wakeup_flags() were not exported, and
are used when PM is enabled
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue that sometimes this controller is not able
to complete the Control write status stage.
This driver should enable DCPCTR.CCPL and PID_BUF to complete the status
stage. However, if this driver detects the ctrl_stage interruption first
before the control write data is received, this driver will clear the
PID_BUF wrongly in the usbhsf_pio_try_pop(). To avoid this issue, this
patch doesn't clear the PID_BUF in the usbhsf_pio_try_pop().
(Since also the privious code doesn't disable the PID_BUF after a control
transfer was finished, this patch doesn't have any side efforts.)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch fixes an issue for control write. When usbhsf_prepare_pop()
is called after this driver called a gadget setup function, this controller
doesn't receive the control write data. So, this patch adds a code to clear
the fifo for control write in usbhsf_prepare_pop().
Signed-off-by: Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for USB controller version-2.5 used in
T4240 rev2.0, T1024, T1040, T2080, LS1021A
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Check IP version 2.4 for multi port host USB controller and
return FSL_USB_VER_2_4 macro
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix USB 3.0 devices lost in NOTATTACHED state after a hub port reset.
Dissolve the function hub_port_finish_reset() completely and divide the
actions to be taken into those which need to be done after each reset
attempt and those which need to be done after the full procedure is
complete, and place them in the appropriate places in hub_port_reset().
Also, remove an unneeded forward declaration of hub_port_reset().
Verbose Problem Description:
USB 3.0 devices may be "lost for good" during a hub port reset.
This makes Linux unable to boot from USB 3.0 devices in certain
constellations of host controllers and devices, because the USB device is
lost during initialization, preventing the rootfs from being mounted.
The underlying problem is that in the affected constellations, during the
processing inside hub_port_reset(), the hub link state goes from 0 to
SS.inactive after the initial reset, and back to 0 again only after the
following "warm" reset.
However, hub_port_finish_reset() is called after each reset attempt and
sets the state the connected USB device based on the "preliminary" status
of the hot reset to USB_STATE_NOTATTACHED due to SS.inactive, yet when
the following warm reset is complete and hub_port_finish_reset() is
called again, its call to set the device to USB_STATE_DEFAULT is blocked
by usb_set_device_state() which does not allow taking USB devices out of
USB_STATE_NOTATTACHED state.
Thanks to Alan Stern for guiding me to the proper solution and how to
submit it.
Link: http://lkml.kernel.org/r/trinity-25981484-72a9-4d46-bf17-9c1cf9301a31-1432073240136%20()%203capp-gmx-bs27
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Cc: stable <stable@vger.kernel.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The comment stating that xhci_setup_device() is protected by the address
mutex is not true since
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
as xhci handles two buses.
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix the xhci driver from bluntly setting the transferred length to 0 if
we get a STALL on anything else than the data stage of a control transfer.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We used to write the root port state changes in turn for every port,
sleeping 20ms after every port state change. Suspended usb2 ports need
two state changes, taking minimun 40ms per port.
Now instead poll the Port Link State Change (PLC) bit as
the state change to U0 will set this bit.
Suspended usb2 ports still need the extra 20ms delay, but we now change
all the port states at once so we only need to sleep 20ms once all together
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the OTG case, the controller might not yet have been
added or is removed before the system suspends.
Assign xhci->main_hcd during probe to prevent NULL
pointer de-reference in xhci_suspend/resume().
Use the hcd->state flag to check if HCD is halted
and if that is so do nothing for xhci_suspend/resume().
[Only for xhci-plat devices, pci devices need it in gen_setup -Mathias]
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The problem seems to be that if a new device is detected
while we have already removed the shared HCD, then many of the
xhci operations (e.g. xhci_alloc_dev(), xhci_setup_device())
hang as command never completes.
I don't think XHCI can operate without the shared HCD as we've
already called xhci_halt() in xhci_only_stop_hcd() when shared HCD
goes away. We need to prevent new commands from being queued
not only when HCD is dying but also when HCD is halted.
The following lockup was detected while testing the otg state
machine.
[ 178.199951] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.205799] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 178.214458] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f04c hci version 0x100 quirks 0x00010010
[ 178.223619] xhci-hcd xhci-hcd.0.auto: irq 400, io mem 0x48890000
[ 178.230677] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 178.237796] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.245358] usb usb1: Product: xHCI Host Controller
[ 178.250483] usb usb1: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.257783] usb usb1: SerialNumber: xhci-hcd.0.auto
[ 178.267014] hub 1-0:1.0: USB hub found
[ 178.272108] hub 1-0:1.0: 1 port detected
[ 178.278371] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 178.284171] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 178.294038] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 178.301183] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 178.308776] usb usb2: Product: xHCI Host Controller
[ 178.313902] usb usb2: Manufacturer: Linux 4.0.0-rc1-00024-g6111320 xhci-hcd
[ 178.321222] usb usb2: SerialNumber: xhci-hcd.0.auto
[ 178.329061] hub 2-0:1.0: USB hub found
[ 178.333126] hub 2-0:1.0: 1 port detected
[ 178.567585] dwc3 48890000.usb: usb_otg_start_host 0
[ 178.572707] xhci-hcd xhci-hcd.0.auto: remove, state 4
[ 178.578064] usb usb2: USB disconnect, device number 1
[ 178.586565] xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered
[ 178.592585] xhci-hcd xhci-hcd.0.auto: remove, state 1
[ 178.597924] usb usb1: USB disconnect, device number 1
[ 178.603248] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 190.597337] INFO: task kworker/u4:0:6 blocked for more than 10 seconds.
[ 190.604273] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.610228] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.618443] kworker/u4:0 D c05c0ac0 0 6 2 0x00000000
[ 190.625120] Workqueue: usb_otg usb_otg_work
[ 190.629533] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.636915] [<c05c10ac>] (schedule) from [<c05c1318>] (schedule_preempt_disabled+0xc/0x10)
[ 190.645591] [<c05c1318>] (schedule_preempt_disabled) from [<c05c23d0>] (mutex_lock_nested+0x1ac/0x3fc)
[ 190.655353] [<c05c23d0>] (mutex_lock_nested) from [<c046cf8c>] (usb_disconnect+0x3c/0x208)
[ 190.664043] [<c046cf8c>] (usb_disconnect) from [<c0470cf0>] (_usb_remove_hcd+0x98/0x1d8)
[ 190.672535] [<c0470cf0>] (_usb_remove_hcd) from [<c0485da8>] (usb_otg_start_host+0x50/0xf4)
[ 190.681299] [<c0485da8>] (usb_otg_start_host) from [<c04849a4>] (otg_set_protocol+0x5c/0xd0)
[ 190.690153] [<c04849a4>] (otg_set_protocol) from [<c0484b88>] (otg_set_state+0x170/0xbfc)
[ 190.698735] [<c0484b88>] (otg_set_state) from [<c0485740>] (otg_statemachine+0x12c/0x470)
[ 190.707326] [<c0485740>] (otg_statemachine) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.716162] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.724742] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.732328] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.739898] 5 locks held by kworker/u4:0/6:
[ 190.744274] #0: ("%s""usb_otg"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.752799] #1: ((&otgd->work)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.761326] #2: (&otgd->fsm.lock){+.+.+.}, at: [<c048562c>] otg_statemachine+0x18/0x470
[ 190.769934] #3: (usb_bus_list_lock){+.+.+.}, at: [<c0470ce8>] _usb_remove_hcd+0x90/0x1d8
[ 190.778635] #4: (&dev->mutex){......}, at: [<c046cf8c>] usb_disconnect+0x3c/0x208
[ 190.786700] INFO: task kworker/1:0:14 blocked for more than 10 seconds.
[ 190.793633] Not tainted 4.0.0-rc1-00024-g6111320 #1058
[ 190.799567] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 190.807783] kworker/1:0 D c05c0ac0 0 14 2 0x00000000
[ 190.814457] Workqueue: usb_hub_wq hub_event
[ 190.818866] [<c05c0ac0>] (__schedule) from [<c05c10ac>] (schedule+0x34/0x98)
[ 190.826252] [<c05c10ac>] (schedule) from [<c05c4e40>] (schedule_timeout+0x13c/0x1ec)
[ 190.834377] [<c05c4e40>] (schedule_timeout) from [<c05c19f0>] (wait_for_common+0xbc/0x150)
[ 190.843062] [<c05c19f0>] (wait_for_common) from [<bf068a3c>] (xhci_setup_device+0x164/0x5cc [xhci_hcd])
[ 190.852986] [<bf068a3c>] (xhci_setup_device [xhci_hcd]) from [<c046b7f4>] (hub_port_init+0x3f4/0xb10)
[ 190.862667] [<c046b7f4>] (hub_port_init) from [<c046eb64>] (hub_event+0x704/0x1018)
[ 190.870704] [<c046eb64>] (hub_event) from [<c0053c84>] (process_one_work+0x1b4/0x4a0)
[ 190.878919] [<c0053c84>] (process_one_work) from [<c00540f8>] (worker_thread+0x154/0x44c)
[ 190.887503] [<c00540f8>] (worker_thread) from [<c0058f88>] (kthread+0xd4/0xf0)
[ 190.895076] [<c0058f88>] (kthread) from [<c000e810>] (ret_from_fork+0x14/0x24)
[ 190.902650] 5 locks held by kworker/1:0/14:
[ 190.907023] #0: ("usb_hub_wq"){.+.+.+}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.915454] #1: ((&hub->events)){+.+.+.}, at: [<c0053bf4>] process_one_work+0x124/0x4a0
[ 190.924070] #2: (&dev->mutex){......}, at: [<c046e490>] hub_event+0x30/0x1018
[ 190.931768] #3: (&port_dev->status_lock){+.+.+.}, at: [<c046eb50>] hub_event+0x6f0/0x1018
[ 190.940558] #4: (&bus->usb_address0_mutex){+.+.+.}, at: [<c046b458>] hub_port_init+0x58/0xb10
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't set xhci->shared_hcd to NULL in xhci_stop() as we have
still not de-allocated it. It was resulting in a NULL pointer
de-reference if usb_add/remove_hcd() is called repeatedly.
We want repeated add/remove to work for the OTG use case.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As xhci_hcd is now allocated by usb_create_hcd(), we don't
need to add the primary HCD before creating the shared HCD.
Creating the shared HCD before adding the primary HCD is particularly
useful for the OTG use case so that we know at the OTG core if
the HCD is in single configuration or dual (primary + shared)
configuration.
Signed-off-by: Roger Quadros <rogerq@ti.com>
[Mathias: rearranged to fit on top of the Marvell Armada 385 phy changes]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
HCD core allocates memory for HCD private data in
usb_create_[shared_]hcd() so make use of that
mechanism to allocate the struct xhci_hcd.
Introduce struct xhci_driver_overrides to provide
the size of HCD private data and hc_driver operation
overrides. As of now we only need to override the
reset and start methods.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Simplify target core and target drivers by storing the task tag
a.k.a. command identifier inside struct se_cmd.
For several transports (e.g. SRP) tags are 64 bits wide.
Hence add support for 64-bit tags.
(Fix core_tmr_abort_task conversion spec warnings - nab)
(Fix up usb-gadget to use 16-bit tags - HCH + bart)
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Andy Grover <agrover@redhat.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: <qla2xxx-upstream@qlogic.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that struct se_portal_group contains a protocol identifier field we can
take all the code to format an parse protocol identifiers in CDBs into common
code instead of leaving this to low-level drivers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Now that we store the protocol identifier in the tpg structure we don't
need this method.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Remove the unneeded fabric_ptr argument, and change the type argument
to pass in a SPC protocol identifier.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
Pratyush Anand
Linus Torvalds
Miklos Szeredi
Dan Streetman
Jiri Kosina
Ben Hutchings
Nicholas Bellinger
Thierry Reding
Chanwoo Choi
Greg Kroah-Hartman
Rob Herring
Hauke Mehrtens
Colin Ian King
Alexey Sokolov
Fabio Estevam
John D. Blair
Bart Van Assche
Teunis van Beelen
Vaishali Thakkar
Dennis O'Brien
Hannes Reinecke
Ramneek Mehresh
Yoshihiro Shimoda
Kazuya Mizuguchi
Nikhil Badola
Robert Schlabbach
Chris Bainbridge
Mathias Nyman
Roger Quadros
Christoph Hellwig