| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Fix the regression caused by commit ad78c918602 ("usb: musb: dsps: just
start polling already") which causes polling the ID pin status even in
device-only mode.
Fixes: ad78c918602c ("usb: musb: dsps: just start polling already")
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The recently added endpoint capabilities flags verification breaks Atmel
USBA because the endpoint configuration was only added when the driver
is bound using the legacy pdata interface.
Convert endpoint configuration to new capabilities model when driver is
bound to a device tree as well.
Signed-off-by: Sylvain Rochet <sylvain.rochet@finsecur.com>
Fixes: 47bef3865115 ("usb: gadget: atmel_usba_udc: add ep capabilities support")
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Peter writes:
USB Chipidea fixes for v4.3-rc2
- Fix the stall implementation
- Fix device mode transfer at zynq platform
- other small fixes
|
|
Johan writes:
USB-serial fixes for v4.3-rc2
Just some new ZTE device IDs.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Use imx6sx instead of imx6sl's platform flags for imx6sx.
Fixes: e14db48dfcf3 ("usb: chipidea: imx: add runtime power management support")
Cc: <stable@vger.kernel.org> # v4.1+
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
Due to having hardware tx buffers less than 512 bytes in size, streaming
must be enabled on the Zynq for the udc to work at all. Add platform data
specific to the Zynq udc, which does not set the CI_HDRC_DISABLE_STREAMING
flag.
Based on a patch by the same name from the Xilinx vendor tree.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
According to spec, there are functional and protocol stalls.
For functional stall, it is for bulk and interrupt endpoints,
below are cases for it:
- Host sends SET_FEATURE request for Set-Halt, the udc driver
needs to set stall, and return true unconditionally.
- The gadget driver may call usb_ep_set_halt to stall certain
endpoints, if there is a transfer in pending, the udc driver
should not set stall, and return -EAGAIN accordingly.
These two kinds of stall need to be cleared by host using CLEAR_FEATURE
request (Clear-Halt).
For protocol stall, it is for control endpoint, this stall will
be set if the control request has failed. This stall will be
cleared by next setup request (hardware will do it).
It fixed usbtest (drivers/usb/misc/usbtest.c) Test 13 "set/clear halt"
test failure, meanwhile, this change has been verified by
USB2 CV Compliance Test and MSC Tests.
Cc: <stable@vger.kernel.org> #3.10+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
The gpio-desc migration done in v4.0 caused a regression
with legacy boots due to reversed reset logic.
e.g. omap3-beagle USB host breaks on legacy boot.
Request the reset GPIO with GPIOF_ACTIVE_LOW flag so that
it matches the driver logic and pin behaviour.
Fixes: e9f2cefb0cdc ("usb: phy: generic: migrate to gpio_desc")
Cc: <stable@vger.kernel.org> # 4.0+
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
In certain situations, an interrupt triggers on resume, before musb_start()
has been called. This has been observed to cause enumeration issues after
suspend/resume cycles with AM335x.
Signed-off-by: Pascal Huerst <pascal.huerst@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If a failure happens early in udc_pci_probe(), error handling code
just kfree(dev) and returns. The patch adds proper resource
deallocations in udc_pci_probe() itself,
since udc_pci_remove() is not suitabe to be called so early
in initialization process.
By the way, iounmap(dev->regs) is replaced by iounmap(dev->virt_addr)
in udc_pci_remove() for clarity.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Fix build errors that happen when USB_QCOM_8X16_PHY=y and EXTCON=m:
drivers/built-in.o: In function `phy_8x16_init':
phy-qcom-8x16-usb.c:(.text+0x86ef4): undefined reference to `extcon_get_cable_state'
drivers/built-in.o: In function `phy_8x16_probe':
phy-qcom-8x16-usb.c:(.text+0x870bf): undefined reference to `extcon_get_edev_by_phandle'
phy-qcom-8x16-usb.c:(.text+0x87133): undefined reference to `extcon_register_interest'
phy-qcom-8x16-usb.c:(.text+0x87151): undefined reference to `extcon_unregister_interest'
drivers/built-in.o: In function `phy_8x16_remove':
phy-qcom-8x16-usb.c:(.text+0x872ec): undefined reference to `extcon_unregister_interest'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The change ensures otg is not in a A- state when checking for VBUS in
peripheral mode.
musb_start() where VBUS checking is in can be called in many situations.
One example is in babble recovery routine, in which otg is transitioning
from A-HOST to A-WAIT-BCON, but VBUS discharge takes time, so
musb->is_active could be set to 1 due to this improper checking, then it
causes musb_bus_suspend() failed which leads to warning log message
flooding.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
If we enable IRQs before requesting our
extcon device, we might fall into a situation
where and IRQ fires before we're ready to
handle it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This patch fixes possible regression introduced by
patch reworking endpoint claiming mechanism. It restores
setring ep->driver_data to NULL in usb_ep_autoconfig_reset(),
which was removed by patch commit cc476b42a39d.
Fixes: cc476b42a39d ("usb: gadget: encapsulate endpoint
claiming mechanism")
Reported-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is intended to add ZTE device PIDs on kernel.
Signed-off-by: Liu.Zhao <lzsos369@163.com>
Cc: stable <stable@vger.kernel.org>
[johan: sort the new entries ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree for 4.3 (kerneldoc updates, printk()
fixes, Documentation and MAINTAINERS updates)"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (28 commits)
MAINTAINERS: update my e-mail address
mod_devicetable: add space before */
scsi: a100u2w: trivial typo in printk
i2c: Fix typo in i2c-bfin-twi.c
treewide: fix typos in comment blocks
Doc: fix trivial typo in SubmittingPatches
proportions: Spelling s/consitent/consistent/
dm: Spelling s/consitent/consistent/
aic7xxx: Fix typo in error message
pcmcia: Fix typo in locking documentation
scsi/arcmsr: Fix typos in error log
drm/nouveau/gr: Fix typo in nv10.c
[SCSI] Fix printk typos in drivers/scsi
staging: comedi: Grammar s/Enable support a/Enable support for a/
Btrfs: Spelling s/consitent/consistent/
README: GTK+ is a acronym
ASoC: omap: Fix typo in config option description
mm: tlb.c: Fix error message
ntfs: super.c: Fix error log
fix typo in Documentation/SubmittingPatches
...
|
|
This is an HP-branded Sierra Wireless EM7355:
https://bugzilla.redhat.com/show_bug.cgi?id=1223646#c2
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CustomWare uses the FTDI VID with custom PIDs for their ShipModul MiniPlex
products.
Signed-off-by: Matthijs Kooijman <matthijs@stdin.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Silence read-urb resubmission errors when the device is going away.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoid spamming the logs (e.g. with -EPROTO errors) when attempting to
resubmit the interrupt urb while a disconnect of an in-use device is
being processed.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The scanner (here DS3508) always returns 64 bytes per urb buffer. The first
byte indicates the data length used in the current buffer. There even was
a comment describing this. But the comment also said that we'll send
everything in the buffer to the tty layer. That means sending the actual
barcode data and lots of trailing zeroes. This patch lets the driver only
send the real data.
Signed-off-by: Philipp Hachtmann <hachti@hachti.de>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver used usb_get_serial_data(port->serial) which compiled but resulted
in a NULL pointer being returned (and subsequently used). I did not go deeper
into this but I guess this is a regression.
Signed-off-by: Philipp Hachtmann <hachti@hachti.de>
Fixes: a85796ee5149 ("USB: symbolserial: move private-data allocation to
port_probe")
Cc: stable <stable@vger.kernel.org> # v3.10
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current code prints all wMaxPacketSize content at endpoint
descriptor, if there is a high speed, high bandwidth endpoint,
it may confuse the users, eg, if there are 3 transactions during
microframe, it will print "wMaxPacket 1400" for packet content.
This commit splits wMaxpacketSize and transaction numbers for
output messages.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The ehci platform device's drvdata is the pointer of struct usb_hcd
already, so we doesn't need to call bus_to_hcd conversion again.
Cc: <stable@vger.kernel.org>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 1d958bef45030acfc5578263e9de3bb07032b8da as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit de7718bd9c4d3db96991a98c2a0cb38258a04e47 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit ef0909c50fe63be3f9aa09bdf4db7efaa5919be9 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 187b3d75bbfba45a38b5d1d3656c0f11f6f6f2d0 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 3cf1fc80655d3af7083ea4b3615e5f8532543be7 as the
signed-off-by address is invalid.
Cc: Stefan Koch <stefan.koch10@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Johan writes:
USB-serial updates for v4.3-rc1
Here's a fix for a long-standing issue with the pl2303 divisor
calculations that affects some non-standard baudrates that were enabled
in v3.18.
Adding support for newer Edgeport devices and firmware required changes
to the io_ti driver and also exposed some issues with the driver's
current firmware handling.
Included is also a URL comment-typo fix.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Removed some checkpatch.pl warnings saying there was an unwanted space between
function names and their arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
ohci_hcd_at91_drv_probe() has four at91_for_each_port. They can be merged
into two loops without changing the driver behaviour.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As device tree support is now mandatory, merge ohci_at91_of_init() in
ohci_hcd_at91_drv_probe().
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make the driver depend on CONFIG_OF and remove the now useless #ifdef
Also, fix the Kconfig indentation.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Move struct at91_usbh_data back in ohci-at91.c as this is the only user
left after switching all at91 platforms to DT only.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
With this patch a flag instead of a variable
is used for the default device authorization.
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This introduces an attribute for each interface to
authorize (1) or deauthorize (0) it:
/sys/bus/usb/devices/INTERFACE/authorized
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel supports the device authorization because of wireless USB.
These is usable for wired USB devices, too.
These new interface authorization allows to enable or disable
individual interfaces instead a whole device.
If a deauthorized interface will be authorized so the driver probing must
be triggered manually by writing INTERFACE to /sys/bus/usb/drivers_probe
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Driver probings and interface claims get rejected
if an interface is not authorized.
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Interfaces are allowed per default.
This can disabled or enabled (again) by writing 0 or 1 to
/sys/bus/usb/devices/usbX/interface_authorized_default
Signed-off-by: Stefan Koch <skoch@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix one occurrence of the checkpatch.pl error:
ERROR: do not use assignment in if condition
The semantic patch that makes this change is:
// <smpl>
@@
identifier i;
expression E, E2, E3;
statement S1, S2;
binary operator b;
@@
+ i = E;
if (
- (i = E)
+ i
b
... && E2 && E3 ) S1 else S2
// </smpl>
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Definitions from linux/platform_data/atmel.h are not used, remove the
include.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix one occurrence of the checkpatch error:
ERROR: code indent should use tabs where possible
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix one occurrence of the checkpatch error:
ERROR: space prohibited before open square bracket '['
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Incoming packets in high speed are randomly corrupted by h/w
resulting in multiple errors. This workaround makes FS as
default mode in all affected socs by disabling HS chirp
signalling.This errata does not affect FS and LS mode.
Forces all HS devices to connect in FS mode for all socs
affected by this erratum:
P3041 and P2041 rev 1.0 and 1.1
P5020 and P5010 rev 1.0 and 2.0
P5040, P1010 and T4240 rev 1.0
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Peter writes:
USB: chipidea updates for v4.3-rc1
The main changes are adding several system interfaces for
tuning performance, and each vendors can adjust them according
to their design configurations.
Others are tiny improvements, like more well siTD supports,
USB_DEVICE_A_HNP_SUPPORT supports, etc.
|
|
Felipe writes:
usb: patches for v4.3 merge window
New support for Allwinne SoC on the MUSB driver has been added to the list of
glue layers. MUSB also got support for building all DMA engines in one binary;
this will be great for distros.
DWC3 now has no trace of dev_dbg()/dev_vdbg() usage. We will rely solely on
tracing to debug DWC3. There was also a fix for memory corruption with EP0 when
maxpacket size transfers are > 512 bytes.
Robert's EP capabilities flags is making EP selection a lot simpler. UDCs are
now required to set these flags up when adding endpoints to the framework.
Other than these, we have the usual set of miscelaneous cleanups and minor
fixes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The user can adjust it through dts or platform data
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
|
With this setting and AHBBRST at SBUSCFG as "Incremental burst of
unspecified length", each non-burst size can be taken as single
transfer. It is benefit for non-burst size transfer.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
|
Bin Liu
Sylvain Rochet
Greg Kroah-Hartman
Li Jun
Nathan Sullivan
Peter Chen
Roger Quadros
Luis de Bethencourt
Pascal Huerst
Alexey Khoroshilov
Randy Dunlap
Felipe Balbi
Robert Baldyga
Liu.Zhao
Linus Torvalds
David Ward
Matthijs Kooijman
Johan Hovold
Philipp Hachtmann
Chase Metzger
Alexandre Belloni
Stefan Koch
Kris Borer
Nikhil Badola