| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Since maxpacket_limit was introduced all UDC drivers should use
usb_ep_set_maxpacket_limit() function instead of setting maxpacket value
manually. ep.maxpacket_limit contains actual maximum maxpacket value
supported by hardware which is needed by epautoconf.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Function midi registers two interfaces with single set_alt() function
which means that f_midi_set_alt() is called twice when configuration
is set. That means that endpoint initialization and ep request allocation
is done two times. To avoid this problem we do such things only once,
for interface number 1 (MIDI Streaming interface).
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Function ffs_do_functionfs_bind() calls functionfs_bind() which allocates
usb request and increments refcounts. These things needs to be cleaned
up by if further steps of initialization fail by calling functionfs_unbind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
When using Edgeport/416 models with newer firmware (sometime after
firmware version 4.80.0), idle ports are automatically bounced
(disconnected and then reconnected) approximately every 60 seconds.
This breaks programs (e.g: minicom) where idle periods are common,
normal and expected.
I confirmed with the manufacturer (Digi International) that Edgeport/416
models now ship from the factory with firmware that expects periodic
"heartbeat" queries from the driver to keep idle ports alive. This
patch implements heartbeat support using the mechanism Digi suggested
(periodically requesting an I2C descriptor address) that appears effective
on Edgeports running the newer firmware (that require it) and benign on
Edgeport devices running older firmware. Since we know that Edgeport
firmware version 4.80 (the version distributed in /lib/firmware/down3.bin
and used for Edgeports that are either running still older versions or
have no onboard non-volatile firmware image) does not require heartbeat
support, this patch schedules heartbeats only on Edgeport/416 devices,
and only if they are running firmware versions newer than 4.80.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
[johan: minor style changes ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Do what we can to verify that the driver's firmware image is valid
(before attempting to download it to the Edgeport) by adding a new
function, check_fw_sanity(), and a call to it in in download_fw().
Note: It looks like some Edgeports (models like the EP/416 with on-board
E2PROM) may be able to function even if the on-disk firmware image is
bad or missing, iff their local E2PROM versions are valid. But most
Edgeport models (I've tried EP/1 and EP/8) do not appear to have this
capability and they always rely on the on-disk firmware image.
I tested an implementation that calls the new check_fw_sanity()
function at the top of download_fw() and, rather than simply returning
an error if the firmware image is bad or missing, it saves the result
and defers the decision until later when it may find that it is running
on a E2PROM-equipped device with a valid image. But I think this is
messier than it is worth (adding still more messiness to the already
very messy download_fw()) for such a marginal possible benefit. So, at
least for now, I have chosen the much simpler approach of returning an
error whenever edge_startup() fails to load an on-disk firmware image, or
check_fw_sanity() indicates that it is unusable.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
[johan: drop redundant checksum mask ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The io_ti driver fails to download firmware to Edgeport
devices such as the EP/416, even when the on-disk firmware image
(/lib/firmware/edgeport/down3.bin) is more current than the version
on the EP/416. The current download code is broken in a few ways.
Notably it mis-uses global variables OperationalMajorVersion and
OperationalMinorVersion (reading their values before they've been
properly initialized and subsequently initializing them multiple times
without synchronization). This patch drops the global variables and
replaces the redundant calls to request_firmware()/release_firmware()
in download_fw() with a single call pair in edge_startup(); the firmware
image pointer is then passed to download_fw() and build_i2c_fw_hdr().
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The io_ti driver fails to download firmware to Edgeport devices such as
the EP/416 and EP/421 (devices with on-board E2PROM). One of the problems
is that the default 1 second timeout in ti_vsend_sync() is insufficient
for download operations. This patch increases the download timeout to
10 seconds.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Johan writes:
USB-serial fixes for v4.2-rc5
Here's a fix for some Sierra Wireless modems and a couple of new device
ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
According to USB Audio Device 2.0 Spec, Ch4.10.1.1:
wMaxPacketSize is defined as follows:
Maximum packet size this endpoint is capable of sending or receiving
when this configuration is selected.
This is determined by the audio bandwidth constraints of the endpoint.
In current code, the wMaxPacketSize is defined as the maximum packet size
for ISO endpoint, and it will let the host reserve much more space than
it really needs, so that we can't let more endpoints work together at
one frame.
We find this issue when we try to let 4 f_uac2 gadgets work together [1]
at FS connection.
[1]http://www.spinics.net/lists/linux-usb/msg123478.html
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: andrzej.p@samsung.com
Cc: Daniel Mack <zonque@gmail.com>
Cc: tiwai@suse.de
Cc: <stable@vger.kernel.org> #v3.18+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
After the worker thread is launched, bind function is doing further
configuration. In case of failure stop the thread.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Sanjay Singh Rawat <snjsrwt@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
There is an "&&" vs "||" typo here so this loops 3000 times or if we get
unlucky it could loop forever.
Fixes: ceaa0a6eeadf ('usb: gadget: m66592-udc: add support for TEST_MODE')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
We handle the "if (!req->req.length)" condition at the start of the
function and return. We can delete this dead code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
apq8016-sbc board is using Dual SPDT USB Switch (TC7USB40MU),
witch is controlled by GPIO to de/multiplex D+/D- USB lines to
USB2513B Hub and uB connector. Add support for this.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Replace calls of gadget_supports_altsettings() function (which check altset
support by comparing UDC controller name with hardcoded names) with
gadget_is_altset_supported() which checks generic quirk bitfield.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use generic mechanism to check if UDC controller supports zlp.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use generic mechanism to check if UDC controller supports stalling.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Due to some UDC controllers may not support zlp, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_zlp_not_supp' field to struct usb_gadget and helper
function gadget_is_zlp_supported(). It also sets 'quirk_zlp_not_supp'
to 1 in musb UDC driver, which has such limitation.
[ balbi@ti.com : make it build ]
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Due to some UDC controllers may not support stalling, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_stall_not_supp' field to struct usb_gadget and helper
function gadget_is_stall_supported(). It also sets 'quirk_stall_not_supp'
to 1 in at91_udc driver, which has such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Due to some UDC controllers may not support altsettings, usb gadget layer
needs to provide a generic way to inform gadget functions about non-standard
hardware limitations.
This patch adds 'quirk_altset_not_supp' field to struct usb_gadget and helper
function gadget_is_altset_supported(). It also sets 'quirk_altset_not_supp'
to 1 in pxa25x_udc and pxa27x_udc drivers, which have such limitation.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use chained TRB mechanism to handle non maxpacket aligned transfers
greater than bounce buffer size. With this the first TRB will be programmed
to receive 'ALIGN(ur->length - maxp, maxp)' data and the second TRB
will be programmed to receive the remaining data using bounce buffer.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Add chained TRB support to ep0. Now TRB's can be chained just by
invoking _dwc3_ep0_start_trans_ with 'chain' parameter set to true.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
No functional change. Added a new parameter in _dwc3_ep0_start_trans_ to
indicate whether the TRB is a chained TRB or last TRB. This is in
preparation for adding chained TRB support for ep0.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
No functional change. This is in preparation for handling non maxpacket
aligned transfers greater than bounce buffer size. This is basically to
avoid code duplication when using chained TRB transfers to handle
non maxpacket aligned transfers greater than bounce buffer size.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
No functional change. Used _roundup_ macro to calculate the transfer
size aligned to maxpacket in dwc3_ep0_complete_data. It also makes it
similar to how transfer size is calculated in __dwc3_ep0_do_control_data.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
DWC3 uses bounce buffer to handle non max packet aligned OUT transfers and
the size of bounce buffer is 512 bytes. However if the host initiates OUT
transfers of size more than 512 bytes (and non max packet aligned), the
driver throws a WARN dump but still programs the TRB to receive more than
512 bytes. This will cause bounce buffer to overflow and corrupt the
adjacent memory locations which can be fatal.
Fix it by programming the TRB to receive a maximum of DWC3_EP0_BOUNCE_SIZE
(512) bytes.
Cc: <stable@vger.kernel.org> # 3.4+
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This commit fixes the following issues:
1. The 9th bit of buf was believed to be the LSB of divisor's
exponent, but the hardware interprets it as MSB (9th bit) of the
mantissa. The exponent is actually one bit shorter and applies
to base 4, not 2 as previously believed.
2. Loop iterations doubled the exponent instead of incrementing.
3. The exponent wasn't checked for overflow.
4. The function returned requested rate instead of actual rate.
Due to issue #2, the old code deviated from the wrong formula
described in #1 and actually yielded correct rates when divisor
was lower than 4096 by using exponents of 0, 2 or 4 base-2,
interpreted as 0, 1, 2 base-4 with the 9th mantissa bit clear.
However, at 93.75 kbaud or less the rate turned out too slow
due to #2 or too fast due to #2 and #3.
I tested this patch by sending and validating 0x00,0x01,..,0xff
to an FTDI dongle at 234, 987, 2401, 9601, 31415, 115199, 250k,
500k, 750k, 1M, 1.5M, 3M+1 baud. All rates passed.
I also used pv to check speed at some rates unsupported by FTDI:
45 (the lowest possible), 2M, 4M, 5M and 6M-1. Looked sane.
Signed-off-by: Michal Pecio <michal.pecio@gmail.com>
Fixes: 399aa9a75ad3 ("USB: pl2303: use divisors for unsupported baud
rates")
Cc: stable <stable@vger.kernel.org> # v3.18
[johan: update summary ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
These changes allow a PHY driver to trigger a VBUS interrupt and
to provide the value of VBUS.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations. If otg capability
is not defined, keep its original otg descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
ether unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate and initialize usb otg descriptor according to gadget otg
capabilities, add it for each usb configurations, free it while
composite unbind. If otg capability is not defined, keep its otg
descriptor unchanged.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Allocate usb otg descriptor and initialize it according to gadget's otg
capabilities, if usb_otg_caps is not set, keep settings as current gadget
drivers. With this 2 new interfaces, gadget can use usb_otg_descriptor
for OTG 1.x, and usb_otg20_descriptor for OTG 2.0 or above, and otg
features can be decided by the combination of usb hardware property
and driver config.
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
After introduce usb otg properties, update ci_otg_is_fsm_mode conditions
to be depending on both usb hardware properties and usb driver config,
also resolve a compile issue in debug.c after the API change.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Init and update otg capabilities by DT, set gadget's otg capabilities
accordingly.
Acked-by: Peter Chen <peter.chen@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Check property of usb hardware to update otg version and disable SRP, HNP
and ADP if its disable flag is present.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Copy usb_otg_descriptor from config's descriptor if host requests
USB_DT_OTG.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Signed-off-by: Li Jun <jun.li@freescale.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The A33 SoC uses the same musb controller as found on the A31 and later,
but allwinner has removed the configdata register, this commit adds special
handling for this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
The A31 SoC uses the same musb controller as found in earlier SoCs, but it
is hooked up slightly different. Its SRAM is private and no longer controlled
through the SRAM controller, and its reset is controlled via a separate
reset controller. This commit adds support for this setup.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
This is based on initial code to get the Allwinner sunxi musb controller
supported by Chen-Yu Tsai and Roman Byshko.
This adds support for the Allwinner sunxi musb controller in both host only
and otg mode. Peripheral only mode is not supported, as no boards use that.
This has been tested on a cubietruck (A20 SoC) and an UTOO P66 tablet
(A13 SoC) with a variety of devices in host mode and with the g_serial gadget
driver in peripheral mode, plugging otg / host cables in/out a lot of times
in all possible imaginable plug orders.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind(). Field 'can_activate' in struct f_obex is no longer
needed as setting 'bind_deactivated' flag makes us sure, that the function
will be binded only if deactivation can be performed successfully.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
|
Use bind_deactivated flag instead of calling usb_function_deactivate()
in function bind().
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
|
Robert Baldyga
Peter E. Berger
Greg Kroah-Hartman
Peter Chen
Sanjay Singh Rawat
Dan Carpenter
Ivan T. Ivanov
Kishon Vijay Abraham I
Michał Pecio
Phil Edworthy
Li Jun
Macpaul Lin
Hans de Goede