| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull x86 fixes from Thomas Gleixner:
"A couple of x86 fixes which missed rc1 due to my stupidity:
- Drop lazy TLB mode before switching to the temporary address space
for text patching.
text_poke() switches to the temporary mm which clears the lazy mode
and restores the original mm afterwards. Due to clearing lazy mode
this might restore a already dead mm if exit_mmap() runs in
parallel on another CPU.
- Document the x32 syscall design fail vs. syscall numbers 512-547
properly.
- Fix the ORC unwinder to handle the inactive task frame correctly.
This was unearthed due to the slightly different code generation of
gcc-10.
- Use an up to date screen_info for the boot params of kexec instead
of the possibly stale and invalid version which happened to be
valid when the kexec kernel was loaded"
* tag 'x86-urgent-2020-10-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/alternative: Don't call text_poke() in lazy TLB mode
x86/syscalls: Document the fact that syscalls 512-547 are a legacy mistake
x86/unwind/orc: Fix inactive tasks with stack pointer in %sp on GCC 10 compiled kernels
hyperv_fb: Update screen_info after removing old framebuffer
x86/kexec: Use up-to-dated screen_info copy to fill boot params
|
|
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
|
|
Pull parisc updates from Helge Deller:
- Added fw_cfg support for parisc on qemu
- Added font support in sti text console driver for byte- and word-mode
ROMs
- Switch to more fine grained lws locks and improve spinlock handling
- Add ioread64_hi_lo() and iowrite64_hi_lo() to avoid 0-day linking
errors
- Mark pointers volatile in __xchg8(), __xchg32() and __xchg64() to
help compiler
- Header file cleanups, mostly removal of unused HP-UX compat defines
- Drop one bit from our O_NONBLOCK define to become now 000200000
- Add MAP_UNINITIALIZED define to avoid userspace compile errors
- Drop CONFIG_IDE from defconfigs
- Speed up synchronize_caches() on UP machines
- Rewrite tlb flush threshold calculation
- Comment fixes and cleanups
* 'parisc-5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc/sticon: Add user font support
parisc/sticon: Always register sticon console driver
parisc: Add MAP_UNINITIALIZED define
parisc: Improve spinlock handling
parisc: Install vmlinuz instead of zImage file
parisc: Rewrite tlb flush threshold calculation
parisc: Switch to more fine grained lws locks
parisc: Mark pointers volatile in __xchg8(), __xchg32() and __xchg64()
parisc: Fix comments and enable interrupts later
parisc: Add alternative patching to synchronize_caches define
parisc: Add ioread64_hi_lo() and iowrite64_hi_lo()
parisc: disable CONFIG_IDE in defconfigs
parisc: Drop useless comments in uapi/asm/signal.h
parisc: Define O_NONBLOCK to become 000200000
parisc: Drop HP-UX specific fcntl and signal flags
parisc: Avoid external interrupts when IPI finishes
parisc: Add qemu fw_cfg interface
fw_cfg: Add support for parisc architecture
|
|
Pull drm updates from Dave Airlie:
"Not a major amount of change, the i915 trees got split into display
and gt trees to better facilitate higher level review, and there's a
major refactoring of i915 GEM locking to use more core kernel concepts
(like ww-mutexes). msm gets per-process pagetables, older AMD SI cards
get DC support, nouveau got a bump in displayport support with common
code extraction from i915.
Outside of drm this contains a couple of patches for hexint
moduleparams which you've acked, and a virtio common code tree that
you should also get via it's regular path.
New driver:
- Cadence MHDP8546 DisplayPort bridge driver
core:
- cross-driver scatterlist cleanups
- devm_drm conversions
- remove drm_dev_init
- devm_drm_dev_alloc conversion
ttm:
- lots of refactoring and cleanups
bridges:
- chained bridge support in more drivers
panel:
- misc new panels
scheduler:
- cleanup priority levels
displayport:
- refactor i915 code into helpers for nouveau
i915:
- split into display and GT trees
- WW locking refactoring in GEM
- execbuf2 extension mechanism
- syncobj timeline support
- GEN 12 HOBL display powersaving
- Rocket Lake display additions
- Disable FBC on Tigerlake
- Tigerlake Type-C + DP improvements
- Hotplug interrupt refactoring
amdgpu:
- Sienna Cichlid updates
- Navy Flounder updates
- DCE6 (SI) support for DC
- Plane rotation enabled
- TMZ state info ioctl
- PCIe DPC recovery support
- DC interrupt handling refactor
- OLED panel fixes
amdkfd:
- add SMI events for thermal throttling
- SMI interface events ioctl update
- process eviction counters
radeon:
- move to dma_ for allocations
- expose sclk via sysfs
msm:
- DSI support for sm8150/sm8250
- per-process GPU pagetable support
- Displayport support
mediatek:
- move HDMI phy driver to PHY
- convert mtk-dpi to bridge API
- disable mt2701 tmds
tegra:
- bridge support
exynos:
- misc cleanups
vc4:
- dual display cleanups
ast:
- cleanups
gma500:
- conversion to GPIOd API
hisilicon:
- misc reworks
ingenic:
- clock handling and format improvements
mcde:
- DSI support
mgag200:
- desktop g200 support
mxsfb:
- i.MX7 + i.MX8M
- alpha plane support
panfrost:
- devfreq support
- amlogic SoC support
ps8640:
- EDID from eDP retrieval
tidss:
- AM65xx YUV workaround
virtio:
- virtio-gpu exported resources
rcar-du:
- R8A7742, R8A774E1 and R8A77961 support
- YUV planar format fixes
- non-visible plane handling
- VSP device reference count fix
- Kconfig fix to avoid displaying disabled options in .config"
* tag 'drm-next-2020-10-15' of git://anongit.freedesktop.org/drm/drm: (1494 commits)
drm/ingenic: Fix bad revert
drm/amdgpu: Fix invalid number of character '{' in amdgpu_acpi_init
drm/amdgpu: Remove warning for virtual_display
drm/amdgpu: kfd_initialized can be static
drm/amd/pm: setup APU dpm clock table in SMU HW initialization
drm/amdgpu: prevent spurious warning
drm/amdgpu/swsmu: fix ARC build errors
drm/amd/display: Fix OPTC_DATA_FORMAT programming
drm/amd/display: Don't allow pstate if no support in blank
drm/panfrost: increase readl_relaxed_poll_timeout values
MAINTAINERS: Update entry for st7703 driver after the rename
Revert "gpu/drm: ingenic: Add option to mmap GEM buffers cached"
drm/amd/display: HDMI remote sink need mode validation for Linux
drm/amd/display: Change to correct unit on audio rate
drm/amd/display: Avoid set zero in the requested clk
drm/amdgpu: align frag_end to covered address space
drm/amdgpu: fix NULL pointer dereference for Renoir
drm/vmwgfx: fix regression in thp code due to ttm init refactor.
drm/amdgpu/swsmu: add interrupt work handler for smu11 parts
drm/amdgpu/swsmu: add interrupt work function
...
|
|
This is a major rework of the sticon (parisc text console) driver in
order to support user font support.
Usually one want to use the stifb (parisc framebuffer driver) which is
based on fbcon and does support fonts and colors, but some old machines
(e.g. HP 730 workstations) don't provide a supported stifb graphic card,
and for those user fonts are preferred.
This patch drops unused code for software cursor and scrollback,
enhances the debug output and adds better documentation.
The code was tested on various machines with byte-mode and word-mode
graphic cards on GSC- and PCI-busses.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
If the ROM provides functional STI routines, always register the sticon
driver, even if the serial console was choosen as boot device.
Additionally, in that case, do not make the sticon driver the default
output console device.
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Pull tty/serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.10-rc1.
Lots of little things in here, including:
- tasklet_setup api conversions
- sysrq support for capital letters
- vt and vc cleanups and unwinding the mess some more
- serial driver updates and minor tweaks
- new device ids
- rs485 support for some drivers
- serial binding documentation updates
- lots of small serial driver changes for reported issues
All have been in linux-next for a while with no reported issues"
* tag 'tty-5.10-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (79 commits)
serial: mcf: add sysrq capability
serial: fsl_lpuart: add sysrq support when using dma
fbcon: remove no-op fbcon_set_origin()
tty/sysrq: Extend the sysrq_key_table to cover capital letters
serial: max310x: rework RX interrupt handling
serial: 8250_dw: Fix clk-notifier/port suspend deadlock
serial: 8250: Skip uninitialized TTY port baud rate update
serial: 8250: Discard RTS/DTS setting from clock update method
tty: serial: imx: disable TXDC IRQ in imx_uart_shutdown() to avoid IRQ storm
serial: 8250_fsl: Fix TX interrupt handling condition
serial: pl011: Fix lockdep splat when handling magic-sysrq interrupt
tty: serial: fsl_lpuart: fix lpuart32_poll_get_char
tty: serial: lpuart: fix lpuart32_write usage
serial: qcom_geni_serial: To correct QUP Version detection logic
serial: mvebu-uart: fix unused variable warning
vt_ioctl: make VT_RESIZEX behave like VT_RESIZE
serial: mvebu-uart: simplify the return expression of mvebu_uart_probe()
tty: serial: imx: fix link error with CONFIG_SERIAL_CORE_CONSOLE=n
tty: hvc: fix link error with CONFIG_SERIAL_CORE_CONSOLE=n
pch_uart: drop double zeroing
...
|
|
Pull backlight updates from Lee Jones:
"New Drivers:
- Add support for KTD253
Fix-ups:
- Add Device Tree documentation; common, kinetic,ktd253
- Use correct header(s); tosa_lcd, tosa_bl
Bug Fixes:
- Fix refcount imbalance; sky81452-backlight"
* tag 'backlight-next-5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: tosa_bl: Include the right header
backlight: tosa_lcd: Include the right header
backlight: Add Kinetic KTD253 backlight driver
dt-bindings: backlight: Add Kinetic KTD253 bindings
dt-bindings: backlight: Add some common backlight properties
backlight: sky81452-backlight: Fix refcount imbalance on error
|
|
On gen2 HyperV VM, hyperv_fb will remove the old framebuffer, and the
new allocated framebuffer address could be at a differnt location,
and it might be no longer a VGA framebuffer.
Update screen_info so that after kexec the kernel won't try to reuse
the old invalid/stale framebuffer address as VGA, corrupting memory.
[ mingo: Tidied up the changelog. ]
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Dexuan Cui <decui@microsoft.com>
Cc: Jake Oshins <jakeo@microsoft.com>
Cc: Wei Hu <weh@microsoft.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Link: https://lore.kernel.org/r/20201014092429.1415040-3-kasong@redhat.com
|
|
drm-misc-fixes for v5.9:
- Small doc fix.
- Re-add FB_ARMCLCD for android.
- Fix global-out-of-bounds read in fbcon_get_font().
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/8585daa2-fcbc-3924-ac4f-e7b5668808e0@linux.intel.com
|
|
We don't need to call vc->vc_sw->con_set_origin() from set_origin()
if it is no-op.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/20200915000019.3422-3-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Also partially revert the follow-up change "drm: pl111: Absorb the
external register header".
This reverts the parts of commits
7e4e589db76a3cf4c1f534eb5a09cc6422766b93 and
0fb8125635e8eb5483fb095f98dcf0651206a7b8 that touch paths outside
of drivers/gpu/drm/pl111.
The fbdev driver is used by Android's FVP configuration. Using the
DRM driver together with DRM's fbdev emulation results in a failure
to boot Android. The root cause is that Android's generic fbdev
userspace driver relies on the ability to set the pixel format via
FBIOPUT_VSCREENINFO, which is not supported by fbdev emulation.
There have been other less critical behavioral differences identified
between the fbdev driver and the DRM driver with fbdev emulation. The
DRM driver exposes different values for the panel's width, height and
refresh rate, and the DRM driver fails a FBIOPUT_VSCREENINFO syscall
with yres_virtual greater than the maximum supported value instead
of letting the syscall succeed and setting yres_virtual based on yres.
Signed-off-by: Peter Collingbourne <pcc@google.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200929195344.2219796-1-pcc@google.com
|
|
fbcon_get_font() is reading out-of-bounds. A malicious user may resize
`vc->vc_font.height` to a large value, causing fbcon_get_font() to
read out of `fontdata`.
fbcon_get_font() handles both built-in and user-provided fonts.
Fortunately, recently we have added FONT_EXTRA_WORDS support for built-in
fonts, so fix it by adding range checks using FNTSIZE().
This patch depends on patch "fbdev, newport_con: Move FONT_EXTRA_WORDS
macros into linux/font.h", and patch "Fonts: Support FONT_EXTRA_WORDS
macros for built-in fonts".
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+29d4ed7f3bdedf2aa2fd@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=08b8be45afea11888776f897895aef9ad1c3ecfd
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/b34544687a1a09d6de630659eb7a773f4953238b.1600953813.git.yepeilin.cs@gmail.com
|
|
drivers/video/console/newport_con.c is borrowing FONT_EXTRA_WORDS macros
from drivers/video/fbdev/core/fbcon.h. To keep things simple, move all
definitions into <linux/font.h>.
Since newport_con now uses four extra words, initialize the fourth word in
newport_set_font() properly.
Cc: stable@vger.kernel.org
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/7fb8bc9b0abc676ada6b7ac0e0bd443499357267.1600953813.git.yepeilin.cs@gmail.com
|
|
We need the tty/serial fixes in here and this resolves a merge issue in
the 8250 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull tty/serial/fbcon fixes from Greg KH:
"Here are some small tty/serial and one more fbcon fix.
They include:
- serial core locking regression fixes
- new device ids for 8250_pci driver
- fbcon fix for syzbot found issue
All have been in linux-next with no reported issues"
* tag 'tty-5.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fbcon: Fix user font detection test at fbcon_resize().
serial: 8250_pci: Add Realtek 816a and 816b
serial: core: fix console port-lock regression
serial: core: fix port-lock initialisation
|
|
Remove the superfluous break, as there is a 'return' before it.
Fixes: bad07ff74c32 ("fbcon: smart blitter usage for scrolling")
Signed-off-by: Jing Xiangfeng <jingxiangfeng@huawei.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200918010521.69950-1-jingxiangfeng@huawei.com
|
|
The changes made in below mentioned commit removed CONFIG_PM containers
from drivers/video/fbdev/aty/atyfb_base.c but not from
drivers/video/fbdev/aty/atyfb.h for respective callbacks.
This resulted in error for implicit declaration for those callbacks.
Fixes: 348b2956d5e6 ("fbdev: aty: use generic power management")
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20200917115313.725622-1-vaibhavgupta40@gmail.com
|
|
We don't need to call vc->vc_sw->con_set_origin() from set_origin()
if it is no-op.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/20200915000019.3422-2-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We don't need to call vc->vc_sw->con_set_origin() from set_origin()
if it is no-op.
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/20200915000019.3422-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzbot is reporting OOB read at fbcon_resize() [1], for
commit 39b3cffb8cf31117 ("fbcon: prevent user font height or width change
from causing potential out-of-bounds access") is by error using
registered_fb[con2fb_map[vc->vc_num]]->fbcon_par->p->userfont (which was
set to non-zero) instead of fb_display[vc->vc_num].userfont (which remains
zero for that display).
We could remove tricky userfont flag [2], for we can determine it by
comparing address of the font data and addresses of built-in font data.
But since that commit is failing to fix the original OOB read [3], this
patch keeps the change minimal in case we decide to revert altogether.
[1] https://syzkaller.appspot.com/bug?id=ebcbbb6576958a496500fee9cf7aa83ea00b5920
[2] https://syzkaller.appspot.com/text?tag=Patch&x=14030853900000
[3] https://syzkaller.appspot.com/bug?id=6fba8c186d97cf1011ab17660e633b1cc4e080c9
Reported-by: syzbot <syzbot+b38b1ef6edf0c74a8d97@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 39b3cffb8cf31117 ("fbcon: prevent user font height or width change from causing potential out-of-bounds access")
Cc: George Kennedy <george.kennedy@oracle.com>
Link: https://lore.kernel.org/r/f6e3e611-8704-1263-d163-f52c906a4f06@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Yunhai Zhang recently fixed a VGA software scrollback bug in commit
ebfdfeeae8c0 ("vgacon: Fix for missing check in scrollback handling"),
but that then made people look more closely at some of this code, and
there were more problems on the vgacon side, but also the fbcon software
scrollback.
We don't really have anybody who maintains this code - probably because
nobody actually _uses_ it any more. Sure, people still use both VGA and
the framebuffer consoles, but they are no longer the main user
interfaces to the kernel, and haven't been for decades, so these kinds
of extra features end up bitrotting and not really being used.
So rather than try to maintain a likely unused set of code, I'll just
aggressively remove it, and see if anybody even notices. Maybe there
are people who haven't jumped on the whole GUI badnwagon yet, and think
it's just a fad. And maybe those people use the scrollback code.
If that turns out to be the case, we can resurrect this again, once
we've found the sucker^Wmaintainer for it who actually uses it.
Reported-by: NopNop Nop <nopitydays@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Cc: 张云海 <zhangyunhai@nsfocus.com>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Acked-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Since the softscroll code got removed, this argument is always zero and
makes no sense any more.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This (and the VGA soft scrollback) turns out to have various nasty small
special cases that nobody really is willing to fight. The soft
scrollback code was really useful a few decades ago when you typically
used the console interactively as the main way to interact with the
machine, but that just isn't the case any more.
So it's not worth dragging along.
Tested-by: Yuan Ming <yuanmingbuaa@gmail.com>
Tested-by: Willy Tarreau <w@1wt.eu>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Paul Cercueil needs some patches in -rc5 to apply new patches for ingenic
properly.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Paul needs 1a21e5b930e8 ("drm/ingenic: Fix leak of device_node
pointer") and 3b5b005ef7d9 ("drm/ingenic: Fix driver not probing when
IPU port is missing") from -fixes to be able to merge further ingenic
patches into -next.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Drivers using legacy PCI power management .suspend()/.resume() callbacks
have to manage PCI states and device's PM states themselves. They also
need to take care of standard configuration registers.
Switch to generic power management framework using a "struct dev_pm_ops"
variable to take the unnecessary load from the driver.
This also avoids the need for the driver to directly call most of the PCI
helper functions and device power state control functions, as through
the generic framework PCI Core takes care of the necessary operations,
and drivers are required to do only device-specific jobs.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200907070221.29938-3-vaibhavgupta40@gmail.com
|
|
Fixes commit 42ddb453a0cd ("radeon: Conditionally compile PM code")
Before the above mentioned patch, codes between the line number 547 and
2803 were already inside "#ifdef CONFIG_PM" container. Thus, addition of
"#if defined(CONFIG_PM)" was not required in the patch. It also affected
the "#ifdef CONFIG_PPC_OF" container (line 1943-2510).
From the current snapshot of radeon_pm.c, remove:
1434 | #if defined(CONFIG_PM)
and,
2213 | #endif
This removes the redundant CONFIG_PM directive as well as fixes the
CONFIG_PPC (earlier CONFIG_PPC_OF) container.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Thierry Reding <treding@nvidia.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200907070221.29938-2-vaibhavgupta40@gmail.com
|
|
The only in-tree user for mbx driver for Intel 2700G graphics chip was
cm-x270 platform. Since this platform was removed by the commit
9d3239147d6d ("ARM: pxa: remove Compulab pxa2xx boards") there is no
point to keep the obsolete framebuffer driver.
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200830115524.431278-1-rppt@kernel.org
|
|
This addresses the following gcc warning with "make W=1":
drivers/video/fbdev/kyro/STG4000InitDevice.c: In function
‘SetCoreClockPLL’:
drivers/video/fbdev/kyro/STG4000InitDevice.c:247:6: warning: variable
‘ulCoreClock’ set but not used [-Wunused-but-set-variable] // yanaijie
fixed
247 | u32 ulCoreClock;
| ^~~~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
[b.zolnierkie: minor patch summary fixup]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827130028.428893-1-yanaijie@huawei.com
|
|
This addresses the following gcc warning with "make W=1":
drivers/video/fbdev/kyro/STG4000InitDevice.c: In function
‘ProgramClock’:
drivers/video/fbdev/kyro/STG4000InitDevice.c:123:6: warning: variable
‘ulBestVCO’ set but not used [-Wunused-but-set-variable]
123 | u32 ulBestVCO = 0, ulBestClk = 0, ulBestScore = 0;
| ^~~~~~~~~
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
[b.zolnierkie: minor patch summary fixup]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200827130008.428706-1-yanaijie@huawei.com
|
|
Use kobj_to_dev() instead of container_of()
Generated by: scripts/coccinelle/api/kobj_to_dev.cocci
Cc: Denis Efremov <efremov@linux.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Cc: Bernie Thompson <bernie@plugable.com>
[b.zolnierkie: minor patch summary fixup]
[b.zolnierkie: removed "Fixes:" tag (not in upstream tree)]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/alpine.DEB.2.22.394.2008262252270.2522@hadrien
|
|
When radeon_kick_out_firmware_fb() fails, info should be
freed just like the subsequent error paths.
Fixes: 069ee21a82344 ("fbdev: Fix loading of module radeonfb on PowerMac")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Mathieu Malaterre <malat@debian.org>
Cc: Kangjie Lu <kjlu@umn.edu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200825062900.11210-1-dinghao.liu@zju.edu.cn
|
|
Use semicolons and braces.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Jiri Kosina <trivial@kernel.org>
[b.zolnierkie: minor patch summary fixup]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ <3e56046e67e583ac93030297ff6d58c08ca54086.1598331149.git.joe@perches.com
|
|
par->vgapass is a u8, so if we are assuming that buf is at least
PAGE_SIZE then the extra checking is pointless.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
[b.zolnierkie: minor patch summary fixup]
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200824174407.429817-1-alex.dewar90@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
The ark_pci_suspend() is not designed to function in the case of Freeze.
Thus, the code checked for "if (state.event == PM_EVENT_FREEZE....)". This
is because, in the legacy framework, this callback was invoked even in the
event of Freeze. Hence, added the load of unnecessary function-call.
The goal can be achieved by binding the callback with only ".suspend" and
".poweroff" in the "ark_pci_pm_ops" const variable. This also avoids the
step of checking "state.event == PM_EVENT_FREEZE" every time the callback
is invoked.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-13-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
The s3_pci_suspend() is not designed to function in the case of Freeze.
Thus, the code checked for "if (state.event == PM_EVENT_FREEZE....)". This
is because, in the legacy framework, this callback was invoked even in the
event of Freeze. Hence, added the load of unnecessary function-call.
The goal can be achieved by binding the callback with only ".suspend" and
".poweroff" in the "s3_pci_pm_ops" const variable. This also avoids the
step of checking "state.event == PM_EVENT_FREEZE" every time the callback
is invoked.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-12-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
The vt8623_pci_suspend() is not designed to function in the case of Freeze.
Thus, the code checked for "if (state.event == PM_EVENT_FREEZE....)". This
is because, in the legacy framework, this callback was invoked even in the
event of Freeze. Hence, added the load of unnecessary function-call.
The goal can be achieved by binding the callback with only ".suspend" and
".poweroff" in the "vt8623_pci_pm_ops" const variable. This also avoids the
step of checking "state.event == PM_EVENT_FREEZE" every time the callback
is invoked.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-11-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
The i740fb_suspend() is not designed to function in the case of Freeze.
Thus, the code checked for "if (state.event == PM_EVENT_FREEZE....)". This
is because, in the legacy framework, this callback was invoked even in the
event of Freeze. Hence, added the load of unnecessary function-call.
The goal can be achieved by binding the callback with only ".suspend" and
".poweroff" in the "i740fb_pm_ops" const variable. This also avoids the
step of checking "if (state.event == PM_EVENT_FREEZE....)" every time the
callback is invoked.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-10-vaibhavgupta40@gmail.com
|
|
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. This way we can
remove the legacy .suspend & .resume bindings from "lxfb_driver".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-9-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Now,
- savagefb_suspend() had a "pm_message_t" type parameter as per legacy
PCI PM framework that got deprecated in generic.
- Rename the callback as savagefb_suspend_late() and preserve the
parameter.
- Define 3 new callbacks as:
* savagefb_suspend()
* savagefb_freeze()
* savagefb_hibernate()
which in turn call savagefb_suspend_late() by passing appropriate value
for "pm_message_t" type parameter.
- Bind the callbacks in "struct dev_pm_ops" type variable
"savagefb_pm_ops".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-8-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Now,
- nvidiafb_suspend() had a "pm_message_t" type parameter as per legacy
PCI PM framework that got deprecated in generic.
- Rename the callback as nvidiafb_suspend_late() and preserve the
parameter.
- Define 3 new callbacks as:
* nvidiafb_suspend()
* nvidiafb_freeze()
* nvidiafb_hibernate()
which in turn call nvidiafb_suspend_late() by passing appropriate value
for "pm_message_t" type parameter.
- Bind the callbacks in "struct dev_pm_ops" type variable
"nvidiafb_pm_ops".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-7-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Now,
- aty128_pci_suspend() had a "pm_message_t" type parameter as per legacy
PCI PM framework that got deprecated in generic.
- Rename the callback as aty128_pci_suspend_late() and preserve the
parameter.
- Define 3 new callbacks as:
* aty128_pci_suspend()
* aty128_pci_freeze()
* aty128_pci_hibernate()
which in turn call aty128_pci_suspend_late() by passing appropriate
value for "pm_message_t" type parameter.
- Bind the callbacks in "struct dev_pm_ops" type variable
"aty128_pci_pm_ops".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-6-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. Also, remove
unnecessary calls to the PCI Helper functions along with the legacy
.suspend & .resume bindings.
Now,
- atyfb_pci_suspend() had a "pm_message_t" type parameter as per legacy
PCI PM framework, that got deprecated in generic.
- Rename the callback as atyfb_pci_suspend_late() and preserve the
parameter.
- Define 3 new callbacks as:
* atyfb_pci_suspend()
* atyfb_pci_freeze()
* atyfb_pci_hibernate()
which in turn call atyfb_pci_suspend_late() by passing appropriate
value for "pm_message_t" type parameter.
- Bind the callbacks in "struct dev_pm_ops" type variable
"atyfb_pci_pm_ops".
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-5-vaibhavgupta40@gmail.com
|
|
Drivers should do only device-specific jobs. But in general, drivers using
legacy PCI PM framework for .suspend()/.resume() have to manage many PCI
PM-related tasks themselves which can be done by PCI Core itself. This
brings extra load on the driver and it directly calls PCI helper functions
to handle them.
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks.
The via_suspend() is designed to function only in the case of Suspend.
Thus, the code checked for "if (state.event != PM_EVENT_SUSPEND)". This is
because, in the legacy framework, this callback was invoked even in the
event of Freeze and Hibernate. Hence, added the load of unnecessary
function-calls.
The goal can be achieved by binding the callback with only
"via_pm_ops.suspend" in the new framework. This also avoids the step of
checking "if (state.event != PM_EVENT_SUSPEND)" every time the callback is
invoked.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-4-vaibhavgupta40@gmail.com
|
|
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. This way we can
remove the legacy .suspend & .resume bindings from "lxfb_driver".
The lxfb_suspend() is designed to function only in the case of Suspend.
Thus, the code was kept inside "if (state.event == PM_EVENT_SUSPEND)"
container. This is because, in the legacy framework, this callback was
invoked even in the event of Freeze and Hibernate. Hence, added the load of
unnecessary function-calls.
The goal can be achieved by binding the callback with only
"lxfb_pm_ops.suspend" in the new framework. This also avoids the step of
checking "if (state.event == PM_EVENT_SUSPEND)" every time the callback is
invoked.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-3-vaibhavgupta40@gmail.com
|
|
Switch to the new generic framework by updating function signatures and
define a "struct dev_pm_ops" variable to bind PM callbacks. This way we can
remove the legacy .suspend & .resume bindings from "gxfb_driver".
The gxfb_suspend() is designed to function only in the case of Suspend.
Thus, the code was kept inside "if (state.event == PM_EVENT_SUSPEND)"
container. This is because, in the legacy framework, this callback was
invoked even in the event of Freeze and Hibernate. Hence, added the load of
unnecessary function-calls.
The goal can be achieved by binding the callback with only
"gxfb_pm_ops.suspend" in the new framework. This also avoids the step of
checking "if (state.event == PM_EVENT_SUSPEND)" every time the callback is
invoked.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Cc: Bjorn Helgaas <helgaas@kernel.org>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Bjorn Helgaas <bjorn@helgaas.com>
Cc: Vaibhav Gupta <vaibhav.varodek@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Andres Salomon <dilinger@queued.net>
CC: Antonino Daplas <adaplas@gmail.com>
Cc: Shuah Khan <skhan@linuxfoundation.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200819185654.151170-2-vaibhavgupta40@gmail.com
|
|
Clang static analysis reports this representative error
init.c:2501:18: warning: Array access (from variable 'queuedata') results
in a null pointer dereference
templ |= ((queuedata[i] & 0xc0) << 3);
This is the problem block of code
if(ModeNo > 0x13) {
...
if(SiS_Pr->ChipType == SIS_730) {
queuedata = &FQBQData730[0];
} else {
queuedata = &FQBQData[0];
}
} else {
}
queuedata is not set in the else block
Reviewing the old code, the arrays FQBQData730 and FQBQData were
used directly.
So hoist the setting of queuedata out of the if-else block.
Fixes: 544393fe584d ("[PATCH] sisfb update")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805145208.17727-1-trix@redhat.com
|
|
There is a spelling mistake in a pr_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200805102805.15353-1-colin.king@canonical.com
|
Linus Torvalds
Helge Deller
Kairui Song
Dave Airlie
Tetsuo Handa
Peter Collingbourne
Peilin Ye
Greg Kroah-Hartman
Jing Xiangfeng
Vaibhav Gupta
Maxime Ripard
Daniel Vetter
Olof Johansson
Mike Rapoport
Jason Yan
kernel test robot
Dinghao Liu
Joe Perches
Alex Dewar
Tom Rix
Colin Ian King