| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Failed to get irq using name is NOT fatal as driver will use index
to get irq instead, use platform_get_irq_byname_optional() instead
of platform_get_irq_byname() to avoid below error message during
probe:
[ 0.819312] fec 30be0000.ethernet: IRQ int0 not found
[ 0.824433] fec 30be0000.ethernet: IRQ int1 not found
[ 0.829539] fec 30be0000.ethernet: IRQ int2 not found
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dave's Facebook email address is not working, and my attempts
to contact him are failing. Let's remove it to trim down the
list of TLS maintainers.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to improve the tun_info options_len by dropping
the skb when TUNNEL_VXLAN_OPT is set but options_len is less
than vxlan_metadata. This can void a potential out-of-bounds
access on ip_tun_info.
Fixes: ee122c79d422 ("vxlan: Flow based tunneling")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check for !md doens't really work for ip_tunnel_info_opts(info) which
only does info + 1. Also to avoid out-of-bounds access on info, it should
ensure options_len is not less than erspan_metadata in both erspan_xmit()
and ip6erspan_tunnel_xmit().
Fixes: 1a66a836da ("gre: add collect_md mode to ERSPAN tunnel")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is due to error in over budget processing.
When dealing with high throughput, the used buffers
that exceeds the budget is not cleaned up. In addition,
it takes a lot of cycles to clean up the used buffer,
and then the buffer where the valid data is located can take effect.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch, the amount of counters guaranteed per VF in the
resource tracker was MLX4_VF_COUNTERS_PER_PORT * MLX4_MAX_PORTS. It was
set regardless if the VF was single or dual port.
This caused several VFs to have no guaranteed counters although the
system could satisfy their request.
The fix is to dynamically guarantee counters, based on each VF
specification.
Fixes: 9de92c60beaa ("net/mlx4_core: Adjust counter grant policy in the resource tracker")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The switch driver keeps a "vid" variable per port, which signifies _the_
VLAN ID that is stripped on that port's egress (aka the native VLAN on a
trunk port).
That is the way the hardware is designed (mostly). The port->vid is
programmed into REW:PORT:PORT_VLAN_CFG:PORT_VID and the rewriter is told
to send all traffic as tagged except the one having port->vid.
There exists a possibility of finer-grained egress untagging decisions:
using the VCAP IS1 engine, one rule can be added to match every
VLAN-tagged frame whose VLAN should be untagged, and set POP_CNT=1 as
action. However, the IS1 can hold at most 512 entries, and the VLANs are
in the order of 6 * 4096.
So the code is fine for now. But this sequence of commands:
$ bridge vlan add dev swp0 vid 1 pvid untagged
$ bridge vlan add dev swp0 vid 2 untagged
makes untagged and pvid-tagged traffic be sent out of swp0 as tagged
with VID 1, despite user's request.
Prevent that from happening. The user should temporarily remove the
existing untagged VLAN (1 in this case), add it back as tagged, and then
add the new untagged VLAN (2 in this case).
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f1688 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Background information: the driver operates the hardware in a mode where
a single VLAN can be transmitted as untagged on a particular egress
port. That is the "native VLAN on trunk port" use case. Its value is
held in port->vid.
Consider the following command sequence (no network manager, all
interfaces are down, debugging prints added by me):
$ ip link add dev br0 type bridge vlan_filtering 1
$ ip link set dev swp0 master br0
Kernel code path during last command:
br_add_slave -> ocelot_netdevice_port_event (NETDEV_CHANGEUPPER):
[ 21.401901] ocelot_vlan_port_apply: port 0 vlan aware 0 pvid 0 vid 0
br_add_slave -> nbp_vlan_init -> switchdev_port_attr_set -> ocelot_port_attr_set (SWITCHDEV_ATTR_ID_BRIDGE_VLAN_FILTERING):
[ 21.413335] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 0 vid 0
br_add_slave -> nbp_vlan_init -> nbp_vlan_add -> br_switchdev_port_vlan_add -> switchdev_port_obj_add -> ocelot_port_obj_add -> ocelot_vlan_vid_add
[ 21.667421] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 1
So far so good. The bridge has replaced the driver's default pvid used
in standalone mode (0) with its own default_pvid (1). The port's vid
(native VLAN) has also changed from 0 to 1.
$ ip link set dev swp0 up
[ 31.722956] 8021q: adding VLAN 0 to HW filter on device swp0
do_setlink -> dev_change_flags -> vlan_vid_add -> ocelot_vlan_rx_add_vid -> ocelot_vlan_vid_add:
[ 31.728700] ocelot_vlan_port_apply: port 0 vlan aware 1 pvid 1 vid 0
The 8021q module uses the .ndo_vlan_rx_add_vid API on .ndo_open to make
ports be able to transmit and receive 802.1p-tagged traffic by default.
This API is supposed to offload a VLAN sub-interface, which for a switch
port means to add a VLAN that is not a pvid, and tagged on egress.
But the driver implementation of .ndo_vlan_rx_add_vid is wrong: it adds
back vid 0 as "egress untagged". Now back to the initial paragraph:
there is a single untagged VID that the driver keeps track of, and that
has just changed from 1 (the pvid) to 0. So this breaks the bridge
core's expectation, because it has changed vid 1 from untagged to
tagged, when what the user sees is.
$ bridge vlan
port vlan ids
swp0 1 PVID Egress Untagged
br0 1 PVID Egress Untagged
But curiously, instead of manifesting itself as "untagged and
pvid-tagged traffic gets sent as tagged on egress", the bug:
- is hidden when vlan_filtering=0
- manifests as dropped traffic when vlan_filtering=1, due to this setting:
if (port->vlan_aware && !port->vid)
/* If port is vlan-aware and tagged, drop untagged and priority
* tagged frames.
*/
val |= ANA_PORT_DROP_CFG_DROP_UNTAGGED_ENA |
ANA_PORT_DROP_CFG_DROP_PRIO_S_TAGGED_ENA |
ANA_PORT_DROP_CFG_DROP_PRIO_C_TAGGED_ENA;
which would have made sense if it weren't for this bug. The setting's
intention was "this is a trunk port with no native VLAN, so don't accept
untagged traffic". So the driver was never expecting to set VLAN 0 as
the value of the native VLAN, 0 was just encoding for "invalid".
So the fix is to not send 802.1p traffic as untagged, because that would
change the port's native vlan to 0, unbeknownst to the bridge, and
trigger unexpected code paths in the driver.
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Fixes: 7142529f1688 ("net: mscc: ocelot: add VLAN filtering")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the implementation of i2400m_op_rfkill_sw_toggle() the allocated
buffer for cmd should be released before returning. The
documentation for i2400m_msg_to_dev() says when it returns the buffer
can be reused. Meaning cmd should be released in either case. Move
kfree(cmd) before return to be reached by all execution paths.
Fixes: 2507e6ab7a9a ("wimax: i2400: fix memory leak")
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rmmod hip04_eth.ko, we can get the following warning:
Task track: rmmod(1623)>bash(1591)>login(1581)>init(1)
------------[ cut here ]------------
WARNING: CPU: 0 PID: 1623 at kernel/irq/manage.c:1557 __free_irq+0xa4/0x2ac()
Trying to free already-free IRQ 200
Modules linked in: ping(O) pramdisk(O) cpuinfo(O) rtos_snapshot(O) interrupt_ctrl(O) mtdblock mtd_blkdevrtfs nfs_acl nfs lockd grace sunrpc xt_tcpudp ipt_REJECT iptable_filter ip_tables x_tables nf_reject_ipv
CPU: 0 PID: 1623 Comm: rmmod Tainted: G O 4.4.193 #1
Hardware name: Hisilicon A15
[<c020b408>] (rtos_unwind_backtrace) from [<c0206624>] (show_stack+0x10/0x14)
[<c0206624>] (show_stack) from [<c03f2be4>] (dump_stack+0xa0/0xd8)
[<c03f2be4>] (dump_stack) from [<c021a780>] (warn_slowpath_common+0x84/0xb0)
[<c021a780>] (warn_slowpath_common) from [<c021a7e8>] (warn_slowpath_fmt+0x3c/0x68)
[<c021a7e8>] (warn_slowpath_fmt) from [<c026876c>] (__free_irq+0xa4/0x2ac)
[<c026876c>] (__free_irq) from [<c0268a14>] (free_irq+0x60/0x7c)
[<c0268a14>] (free_irq) from [<c0469e80>] (release_nodes+0x1c4/0x1ec)
[<c0469e80>] (release_nodes) from [<c0466924>] (__device_release_driver+0xa8/0x104)
[<c0466924>] (__device_release_driver) from [<c0466a80>] (driver_detach+0xd0/0xf8)
[<c0466a80>] (driver_detach) from [<c0465e18>] (bus_remove_driver+0x64/0x8c)
[<c0465e18>] (bus_remove_driver) from [<c02935b0>] (SyS_delete_module+0x198/0x1e0)
[<c02935b0>] (SyS_delete_module) from [<c0202ed0>] (__sys_trace_return+0x0/0x10)
---[ end trace bb25d6123d849b44 ]---
Currently "rmmod hip04_eth.ko" call free_irq more than once
as devres_release_all and hip04_remove both call free_irq.
This results in a 'Trying to free already-free IRQ' warning.
To solve the problem free_irq has been moved out of hip04_remove.
Signed-off-by: Jiangfeng Xiao <xiaojiangfeng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the highly unlikely event that we fail to allocate either of the
"/txrx" or "/control" workqueues, we should bail cleanly rather than
blindly march on with NULL queue pointer(s) installed in the
'fjes_adapter' instance.
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Nicolas Waisman <nico@semmle.com>
Link: https://lore.kernel.org/lkml/CADJ_3a8WFrs5NouXNqS5WYe7rebFP+_A5CheeqAyD_p7DFJJcg@mail.gmail.com/
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
lan78xx_status() will run with interrupts enabled due to the change in
ed194d136769 ("usb: core: remove local_irq_save() around ->complete()
handler"). generic_handle_irq() expects to be run with IRQs disabled.
[ 4.886203] 000: irq 79 handler irq_default_primary_handler+0x0/0x8 enabled interrupts
[ 4.886243] 000: WARNING: CPU: 0 PID: 0 at kernel/irq/handle.c:152 __handle_irq_event_percpu+0x154/0x168
[ 4.896294] 000: Modules linked in:
[ 4.896301] 000: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 5.3.6 #39
[ 4.896310] 000: Hardware name: Raspberry Pi 3 Model B+ (DT)
[ 4.896315] 000: pstate: 60000005 (nZCv daif -PAN -UAO)
[ 4.896321] 000: pc : __handle_irq_event_percpu+0x154/0x168
[ 4.896331] 000: lr : __handle_irq_event_percpu+0x154/0x168
[ 4.896339] 000: sp : ffff000010003cc0
[ 4.896346] 000: x29: ffff000010003cc0 x28: 0000000000000060
[ 4.896355] 000: x27: ffff000011021980 x26: ffff00001189c72b
[ 4.896364] 000: x25: ffff000011702bc0 x24: ffff800036d6e400
[ 4.896373] 000: x23: 000000000000004f x22: ffff000010003d64
[ 4.896381] 000: x21: 0000000000000000 x20: 0000000000000002
[ 4.896390] 000: x19: ffff8000371c8480 x18: 0000000000000060
[ 4.896398] 000: x17: 0000000000000000 x16: 00000000000000eb
[ 4.896406] 000: x15: ffff000011712d18 x14: 7265746e69206465
[ 4.896414] 000: x13: ffff000010003ba0 x12: ffff000011712df0
[ 4.896422] 000: x11: 0000000000000001 x10: ffff000011712e08
[ 4.896430] 000: x9 : 0000000000000001 x8 : 000000000003c920
[ 4.896437] 000: x7 : ffff0000118cc410 x6 : ffff0000118c7f00
[ 4.896445] 000: x5 : 000000000003c920 x4 : 0000000000004510
[ 4.896453] 000: x3 : ffff000011712dc8 x2 : 0000000000000000
[ 4.896461] 000: x1 : 73a3f67df94c1500 x0 : 0000000000000000
[ 4.896466] 000: Call trace:
[ 4.896471] 000: __handle_irq_event_percpu+0x154/0x168
[ 4.896481] 000: handle_irq_event_percpu+0x50/0xb0
[ 4.896489] 000: handle_irq_event+0x40/0x98
[ 4.896497] 000: handle_simple_irq+0xa4/0xf0
[ 4.896505] 000: generic_handle_irq+0x24/0x38
[ 4.896513] 000: intr_complete+0xb0/0xe0
[ 4.896525] 000: __usb_hcd_giveback_urb+0x58/0xd8
[ 4.896533] 000: usb_giveback_urb_bh+0xd0/0x170
[ 4.896539] 000: tasklet_action_common.isra.0+0x9c/0x128
[ 4.896549] 000: tasklet_hi_action+0x24/0x30
[ 4.896556] 000: __do_softirq+0x120/0x23c
[ 4.896564] 000: irq_exit+0xb8/0xd8
[ 4.896571] 000: __handle_domain_irq+0x64/0xb8
[ 4.896579] 000: bcm2836_arm_irqchip_handle_irq+0x60/0xc0
[ 4.896586] 000: el1_irq+0xb8/0x140
[ 4.896592] 000: arch_cpu_idle+0x10/0x18
[ 4.896601] 000: do_idle+0x200/0x280
[ 4.896608] 000: cpu_startup_entry+0x20/0x28
[ 4.896615] 000: rest_init+0xb4/0xc0
[ 4.896623] 000: arch_call_rest_init+0xc/0x14
[ 4.896632] 000: start_kernel+0x454/0x480
Fixes: ed194d136769 ("usb: core: remove local_irq_save() around ->complete() handler")
Cc: Woojung Huh <woojung.huh@microchip.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Stefan Wahren <wahrenst@gmx.net>
Cc: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Tested-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An earlier bugfix introduced a dependency on CONFIG_NET_SCH_TAPRIO,
but this missed the case of NET_SCH_TAPRIO=m and NET_DSA_SJA1105=y,
which still causes a link error:
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_setup_tc_taprio':
sja1105_tas.c:(.text+0x5c): undefined reference to `taprio_offload_free'
sja1105_tas.c:(.text+0x3b4): undefined reference to `taprio_offload_get'
drivers/net/dsa/sja1105/sja1105_tas.o: In function `sja1105_tas_teardown':
sja1105_tas.c:(.text+0x6ec): undefined reference to `taprio_offload_free'
Change the dependency to only allow selecting the TAS code when it
can link against the taprio code.
Fixes: a8d570de0cc6 ("net: dsa: sja1105: Add dependency for NET_DSA_SJA1105_TAS")
Fixes: 317ab5b86c8e ("net: dsa: sja1105: Configure the Time-Aware Scheduler via tc-taprio offload")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are calling the checksum helper after the dma_map_single()
call to map the packet. This is incorrect as the checksumming
code will touch the packet from the CPU. This means the cache
won't be properly flushes (or the bounce buffering will leave
us with the unmodified packet to DMA).
This moves the calculation of the checksum & vlan tags to
before the DMA mapping.
This also has the side effect of fixing another bug: If the
checksum helper fails, we goto "drop" to drop the packet, which
will not unmap the DMA mapping.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Fixes: 05690d633f30 ("ftgmac100: Upgrade to NETIF_F_HW_CSUM")
Reviewed-by: Vijay Khemka <vijaykhemka@fb.com>
Tested-by: Vijay Khemka <vijaykhemka@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
sk_page_frag() optimizes skb_frag allocations by using per-task
skb_frag cache when it knows it's the only user. The condition is
determined by seeing whether the socket allocation mask allows
blocking - if the allocation may block, it obviously owns the task's
context and ergo exclusively owns current->task_frag.
Unfortunately, this misses recursion through memory reclaim path.
Please take a look at the following backtrace.
[2] RIP: 0010:tcp_sendmsg_locked+0xccf/0xe10
...
tcp_sendmsg+0x27/0x40
sock_sendmsg+0x30/0x40
sock_xmit.isra.24+0xa1/0x170 [nbd]
nbd_send_cmd+0x1d2/0x690 [nbd]
nbd_queue_rq+0x1b5/0x3b0 [nbd]
__blk_mq_try_issue_directly+0x108/0x1b0
blk_mq_request_issue_directly+0xbd/0xe0
blk_mq_try_issue_list_directly+0x41/0xb0
blk_mq_sched_insert_requests+0xa2/0xe0
blk_mq_flush_plug_list+0x205/0x2a0
blk_flush_plug_list+0xc3/0xf0
[1] blk_finish_plug+0x21/0x2e
_xfs_buf_ioapply+0x313/0x460
__xfs_buf_submit+0x67/0x220
xfs_buf_read_map+0x113/0x1a0
xfs_trans_read_buf_map+0xbf/0x330
xfs_btree_read_buf_block.constprop.42+0x95/0xd0
xfs_btree_lookup_get_block+0x95/0x170
xfs_btree_lookup+0xcc/0x470
xfs_bmap_del_extent_real+0x254/0x9a0
__xfs_bunmapi+0x45c/0xab0
xfs_bunmapi+0x15/0x30
xfs_itruncate_extents_flags+0xca/0x250
xfs_free_eofblocks+0x181/0x1e0
xfs_fs_destroy_inode+0xa8/0x1b0
destroy_inode+0x38/0x70
dispose_list+0x35/0x50
prune_icache_sb+0x52/0x70
super_cache_scan+0x120/0x1a0
do_shrink_slab+0x120/0x290
shrink_slab+0x216/0x2b0
shrink_node+0x1b6/0x4a0
do_try_to_free_pages+0xc6/0x370
try_to_free_mem_cgroup_pages+0xe3/0x1e0
try_charge+0x29e/0x790
mem_cgroup_charge_skmem+0x6a/0x100
__sk_mem_raise_allocated+0x18e/0x390
__sk_mem_schedule+0x2a/0x40
[0] tcp_sendmsg_locked+0x8eb/0xe10
tcp_sendmsg+0x27/0x40
sock_sendmsg+0x30/0x40
___sys_sendmsg+0x26d/0x2b0
__sys_sendmsg+0x57/0xa0
do_syscall_64+0x42/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
In [0], tcp_send_msg_locked() was using current->page_frag when it
called sk_wmem_schedule(). It already calculated how many bytes can
be fit into current->page_frag. Due to memory pressure,
sk_wmem_schedule() called into memory reclaim path which called into
xfs and then IO issue path. Because the filesystem in question is
backed by nbd, the control goes back into the tcp layer - back into
tcp_sendmsg_locked().
nbd sets sk_allocation to (GFP_NOIO | __GFP_MEMALLOC) which makes
sense - it's in the process of freeing memory and wants to be able to,
e.g., drop clean pages to make forward progress. However, this
confused sk_page_frag() called from [2]. Because it only tests
whether the allocation allows blocking which it does, it now thinks
current->page_frag can be used again although it already was being
used in [0].
After [2] used current->page_frag, the offset would be increased by
the used amount. When the control returns to [0],
current->page_frag's offset is increased and the previously calculated
number of bytes now may overrun the end of allocated memory leading to
silent memory corruptions.
Fix it by adding gfpflags_normal_context() which tests sleepable &&
!reclaim and use it to determine whether to use current->task_frag.
v2: Eric didn't like gfp flags being tested twice. Introduce a new
helper gfpflags_normal_context() and combine the two tests.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
KCSAN reported a data-race in udp_set_dev_scratch() [1]
The issue here is that we must not write over skb fields
if skb is shared. A similar issue has been fixed in commit
89c22d8c3b27 ("net: Fix skb csum races when peeking")
While we are at it, use a helper only dealing with
udp_skb_scratch(skb)->csum_unnecessary, as this allows
udp_set_dev_scratch() to be called once and thus inlined.
[1]
BUG: KCSAN: data-race in udp_set_dev_scratch / udpv6_recvmsg
write to 0xffff888120278317 of 1 bytes by task 10411 on cpu 1:
udp_set_dev_scratch+0xea/0x200 net/ipv4/udp.c:1308
__first_packet_length+0x147/0x420 net/ipv4/udp.c:1556
first_packet_length+0x68/0x2a0 net/ipv4/udp.c:1579
udp_poll+0xea/0x110 net/ipv4/udp.c:2720
sock_poll+0xed/0x250 net/socket.c:1256
vfs_poll include/linux/poll.h:90 [inline]
do_select+0x7d0/0x1020 fs/select.c:534
core_sys_select+0x381/0x550 fs/select.c:677
do_pselect.constprop.0+0x11d/0x160 fs/select.c:759
__do_sys_pselect6 fs/select.c:784 [inline]
__se_sys_pselect6 fs/select.c:769 [inline]
__x64_sys_pselect6+0x12e/0x170 fs/select.c:769
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff888120278317 of 1 bytes by task 10413 on cpu 0:
udp_skb_csum_unnecessary include/net/udp.h:358 [inline]
udpv6_recvmsg+0x43e/0xe90 net/ipv6/udp.c:310
inet6_recvmsg+0xbb/0x240 net/ipv6/af_inet6.c:592
sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 10413 Comm: syz-executor.0 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 2276f58ac589 ("udp: use a separate rx queue for packet reception")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the SPDX License Identifier style in
header files related to DPAA2 Ethernet driver supporting
Freescale SoCs with DPAA2. For C header files
Documentation/process/license-rules.rst mandates C-like comments
(opposed to C source files where C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__skb_wait_for_more_packets() can be called while other cpus
can feed packets to the socket receive queue.
KCSAN reported :
BUG: KCSAN: data-race in __skb_wait_for_more_packets / __udp_enqueue_schedule_skb
write to 0xffff888102e40b58 of 8 bytes by interrupt on cpu 0:
__skb_insert include/linux/skbuff.h:1852 [inline]
__skb_queue_before include/linux/skbuff.h:1958 [inline]
__skb_queue_tail include/linux/skbuff.h:1991 [inline]
__udp_enqueue_schedule_skb+0x2d7/0x410 net/ipv4/udp.c:1470
__udp_queue_rcv_skb net/ipv4/udp.c:1940 [inline]
udp_queue_rcv_one_skb+0x7bd/0xc70 net/ipv4/udp.c:2057
udp_queue_rcv_skb+0xb5/0x400 net/ipv4/udp.c:2074
udp_unicast_rcv_skb.isra.0+0x7e/0x1c0 net/ipv4/udp.c:2233
__udp4_lib_rcv+0xa44/0x17c0 net/ipv4/udp.c:2300
udp_rcv+0x2b/0x40 net/ipv4/udp.c:2470
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5124
process_backlog+0x1d3/0x420 net/core/dev.c:5955
read to 0xffff888102e40b58 of 8 bytes by task 13035 on cpu 1:
__skb_wait_for_more_packets+0xfa/0x320 net/core/datagram.c:100
__skb_recv_udp+0x374/0x500 net/ipv4/udp.c:1683
udp_recvmsg+0xe1/0xb10 net/ipv4/udp.c:1712
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 13035 Comm: syz-executor.3 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Busy polling usually runs without locks.
Let's use skb_queue_empty_lockless() instead of skb_queue_empty()
Also uses READ_ONCE() in __skb_try_recv_datagram() to address
a similar potential problem.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many poll() handlers are lockless. Using skb_queue_empty_lockless()
instead of skb_queue_empty() is more appropriate.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot reported a data-race [1].
We should use skb_queue_empty_lockless() to document that we are
not ensuring a mutual exclusion and silence KCSAN.
[1]
BUG: KCSAN: data-race in __skb_recv_udp / __udp_enqueue_schedule_skb
write to 0xffff888122474b50 of 8 bytes by interrupt on cpu 0:
__skb_insert include/linux/skbuff.h:1852 [inline]
__skb_queue_before include/linux/skbuff.h:1958 [inline]
__skb_queue_tail include/linux/skbuff.h:1991 [inline]
__udp_enqueue_schedule_skb+0x2c1/0x410 net/ipv4/udp.c:1470
__udp_queue_rcv_skb net/ipv4/udp.c:1940 [inline]
udp_queue_rcv_one_skb+0x7bd/0xc70 net/ipv4/udp.c:2057
udp_queue_rcv_skb+0xb5/0x400 net/ipv4/udp.c:2074
udp_unicast_rcv_skb.isra.0+0x7e/0x1c0 net/ipv4/udp.c:2233
__udp4_lib_rcv+0xa44/0x17c0 net/ipv4/udp.c:2300
udp_rcv+0x2b/0x40 net/ipv4/udp.c:2470
ip_protocol_deliver_rcu+0x4d/0x420 net/ipv4/ip_input.c:204
ip_local_deliver_finish+0x110/0x140 net/ipv4/ip_input.c:231
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_local_deliver+0x133/0x210 net/ipv4/ip_input.c:252
dst_input include/net/dst.h:442 [inline]
ip_rcv_finish+0x121/0x160 net/ipv4/ip_input.c:413
NF_HOOK include/linux/netfilter.h:305 [inline]
NF_HOOK include/linux/netfilter.h:299 [inline]
ip_rcv+0x18f/0x1a0 net/ipv4/ip_input.c:523
__netif_receive_skb_one_core+0xa7/0xe0 net/core/dev.c:5010
__netif_receive_skb+0x37/0xf0 net/core/dev.c:5124
process_backlog+0x1d3/0x420 net/core/dev.c:5955
read to 0xffff888122474b50 of 8 bytes by task 8921 on cpu 1:
skb_queue_empty include/linux/skbuff.h:1494 [inline]
__skb_recv_udp+0x18d/0x500 net/ipv4/udp.c:1653
udp_recvmsg+0xe1/0xb10 net/ipv4/udp.c:1712
inet_recvmsg+0xbb/0x250 net/ipv4/af_inet.c:838
sock_recvmsg_nosec+0x5c/0x70 net/socket.c:871
___sys_recvmsg+0x1a0/0x3e0 net/socket.c:2480
do_recvmmsg+0x19a/0x5c0 net/socket.c:2601
__sys_recvmmsg+0x1ef/0x200 net/socket.c:2680
__do_sys_recvmmsg net/socket.c:2703 [inline]
__se_sys_recvmmsg net/socket.c:2696 [inline]
__x64_sys_recvmmsg+0x89/0xb0 net/socket.c:2696
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 8921 Comm: syz-executor.4 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some paths call skb_queue_empty() without holding
the queue lock. We must use a barrier in order
to not let the compiler do strange things, and avoid
KCSAN splats.
Adding a barrier in skb_queue_empty() might be overkill,
I prefer adding a new helper to clearly identify
points where the callers might be lockless. This might
help us finding real bugs.
The corresponding WRITE_ONCE() should add zero cost
for current compilers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds two more tests to ipv4_addr_metric_test() to
explicitly cover the scenarios fixed by the previous patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit af4d768ad28c ("net/ipv4: Add support for specifying metric
of connected routes"), when updating an IP address with a different metric,
the associated connected route is updated, too.
Still, the mentioned commit doesn't handle properly some corner cases:
$ ip addr add dev eth0 192.168.1.0/24
$ ip addr add dev eth0 192.168.2.1/32 peer 192.168.2.2
$ ip addr add dev eth0 192.168.3.1/24
$ ip addr change dev eth0 192.168.1.0/24 metric 10
$ ip addr change dev eth0 192.168.2.1/32 peer 192.168.2.2 metric 10
$ ip addr change dev eth0 192.168.3.1/24 metric 10
$ ip -4 route
192.168.1.0/24 dev eth0 proto kernel scope link src 192.168.1.0
192.168.2.2 dev eth0 proto kernel scope link src 192.168.2.1
192.168.3.0/24 dev eth0 proto kernel scope link src 192.168.2.1 metric 10
Only the last route is correctly updated.
The problem is the current test in fib_modify_prefix_metric():
if (!(dev->flags & IFF_UP) ||
ifa->ifa_flags & (IFA_F_SECONDARY | IFA_F_NOPREFIXROUTE) ||
ipv4_is_zeronet(prefix) ||
prefix == ifa->ifa_local || ifa->ifa_prefixlen == 32)
Which should be the logical 'not' of the pre-existing test in
fib_add_ifaddr():
if (!ipv4_is_zeronet(prefix) && !(ifa->ifa_flags & IFA_F_SECONDARY) &&
(prefix != addr || ifa->ifa_prefixlen < 32))
To properly negate the original expression, we need to change the last
logical 'or' to a logical 'and'.
Fixes: af4d768ad28c ("net/ipv4: Add support for specifying metric of connected routes")
Reported-and-suggested-by: Beniamino Galvani <bgalvani@redhat.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
memset() the structure ethtool_wolinfo that has padded bytes
but the padded bytes have not been zeroed out.
Signed-off-by: zhanglin <zhang.lin16@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For adapters which support the SGE Doorbell Queue Timer facility,
we configured the Ethernet TX Queues to send CIDX Updates to the
Associated Ethernet RX Response Queue with CPL_SGE_EGR_UPDATE
messages to allow us to respond more quickly to the CIDX Updates.
But, this was adding load to PCIe Link RX bandwidth and,
potentially, resulting in higher CPU Interrupt load.
This patch requests the HW to deliver the CIDX updates to the TX
queue status page rather than generating an ingress queue message
(as an interrupt). With this patch, the load on RX bandwidth is
reduced and a substantial improvement in BW is noticed at lower
IO sizes.
Fixes: d429005fdf2c ("cxgb4/cxgb4vf: Add support for SGE doorbell queue timer")
Signed-off-by: Raju Rangoju <rajur@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In rtnl_net_notifyid(), we certainly can't pass a null GFP flag to
rtnl_notify(). A GFP_KERNEL flag would be fine in most circumstances,
but there are a few paths calling rtnl_net_notifyid() from atomic
context or from RCU critical sections. The later also precludes the use
of gfp_any() as it wouldn't detect the RCU case. Also, the nlmsg_new()
call is wrong too, as it uses GFP_KERNEL unconditionally.
Therefore, we need to pass the GFP flags as parameter and propagate it
through function calls until the proper flags can be determined.
In most cases, GFP_KERNEL is fine. The exceptions are:
* openvswitch: ovs_vport_cmd_get() and ovs_vport_cmd_dump()
indirectly call rtnl_net_notifyid() from RCU critical section,
* rtnetlink: rtmsg_ifinfo_build_skb() already receives GFP flags as
parameter.
Also, in ovs_vport_cmd_build_info(), let's change the GFP flags used
by nlmsg_new(). The function is allowed to sleep, so better make the
flags consistent with the ones used in the following
ovs_vport_cmd_fill_info() call.
Found by code inspection.
Fixes: 9a9634545c70 ("netns: notify netns id events")
Signed-off-by: Guillaume Nault <gnault@redhat.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: Pravin B Shelar <pshelar@ovn.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the SPDX License Identifier style in
header file related to ethernet driver for Cortina Gemini
devices. For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Creating of an SMC-R connection with vlan-id fails, because
smc_listen_work() determines the vlan_id of the connection,
saves it in struct smc_init_info ini, but clears the ini area
again if SMC-D is not applicable.
This patch just resets the ISM device before investigating
SMC-R availability.
Fixes: bc36d2fc93eb ("net/smc: consolidate function parameters")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For SMC sockets forced to fallback to TCP, the file is propagated
from the outer SMC to the internal TCP socket. When closing the SMC
socket, the internal TCP socket file pointer must be restored to the
original NULL value, otherwise memory leaks may show up (found with
CONFIG_DEBUG_KMEMLEAK).
The internal TCP socket is released in smc_clcsock_release(), which
calls __sock_release() function in net/socket.c. This calls the
needed iput(SOCK_INODE(sock)) only, if the file pointer has been reset
to the original NULL-value.
Fixes: 07603b230895 ("net/smc: propagate file from SMC to TCP socket")
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If CONFIG_NET_HWBM is not set, then these stub functions in
<net/hwbm.h> should be declared static to avoid trying to
export them from any driver that includes this.
Fixes the following sparse warnings:
./include/net/hwbm.h:24:6: warning: symbol 'hwbm_buf_free' was not declared. Should it be static?
./include/net/hwbm.h:25:5: warning: symbol 'hwbm_pool_refill' was not declared. Should it be static?
./include/net/hwbm.h:26:5: warning: symbol 'hwbm_pool_add' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the CONFIG_MVNET_BA is not set, then make the stub functions
static inline to avoid trying to export them, and remove hte
following sparse warnings:
drivers/net/ethernet/marvell/mvneta_bm.h:163:6: warning: symbol 'mvneta_bm_pool_destroy' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:165:6: warning: symbol 'mvneta_bm_bufs_free' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:167:5: warning: symbol 'mvneta_bm_construct' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:168:5: warning: symbol 'mvneta_bm_pool_refill' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:170:23: warning: symbol 'mvneta_bm_pool_use' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:181:18: warning: symbol 'mvneta_bm_get' was not declared. Should it be static?
drivers/net/ethernet/marvell/mvneta_bm.h:182:6: warning: symbol 'mvneta_bm_put' was not declared. Should it be static?
Signed-off-by: Ben Dooks (Codethink) <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is networking hardware that isn't based on Ethernet for layers 1 and 2.
For example CAN.
CAN is a multi-master serial bus standard for connecting Electronic Control
Units [ECUs] also known as nodes. A frame on the CAN bus carries up to 8 bytes
of payload. Frame corruption is detected by a CRC. However frame loss due to
corruption is possible, but a quite unusual phenomenon.
While fq_codel works great for TCP/IP, it doesn't for CAN. There are a lot of
legacy protocols on top of CAN, which are not build with flow control or high
CAN frame drop rates in mind.
When using fq_codel, as soon as the queue reaches a certain delay based length,
skbs from the head of the queue are silently dropped. Silently meaning that the
user space using a send() or similar syscall doesn't get an error. However
TCP's flow control algorithm will detect dropped packages and adjust the
bandwidth accordingly.
When using fq_codel and sending raw frames over CAN, which is the common use
case, the user space thinks the package has been sent without problems, because
send() returned without an error. pfifo_fast will drop skbs, if the queue
length exceeds the maximum. But with this scheduler the skbs at the tail are
dropped, an error (-ENOBUFS) is propagated to user space. So that the user
space can slow down the package generation.
On distributions, where fq_codel is made default via CONFIG_DEFAULT_NET_SCH
during compile time, or set default during runtime with sysctl
net.core.default_qdisc (see [1]), we get a bad user experience. In my test case
with pfifo_fast, I can transfer thousands of million CAN frames without a frame
drop. On the other hand with fq_codel there is more then one lost CAN frame per
thousand frames.
As pointed out fq_codel is not suited for CAN hardware, so this patch changes
attach_one_default_qdisc() to use pfifo_fast for "ARPHRD_CAN" network devices.
During transition of a netdev from down to up state the default queuing
discipline is attached by attach_default_qdiscs() with the help of
attach_one_default_qdisc(). This patch modifies attach_one_default_qdisc() to
attach the pfifo_fast (pfifo_fast_ops) if the network device type is
"ARPHRD_CAN".
[1] https://github.com/systemd/systemd/issues/9194
Signed-off-by: Vincent Prince <vincent.prince.fr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
virt_wifi_newlink() calls netdev_upper_dev_link() and it internally
holds reference count of lower interface.
Current code does not release a reference count of the lower interface
when the lower interface is being deleted.
So, reference count leaks occur.
Test commands:
ip link add dummy0 type dummy
ip link add vw1 link dummy0 type virt_wifi
ip link del dummy0
Splat looks like:
[ 133.787526][ T788] WARNING: CPU: 1 PID: 788 at net/core/dev.c:8274 rollback_registered_many+0x835/0xc80
[ 133.788355][ T788] Modules linked in: virt_wifi cfg80211 dummy team af_packet sch_fq_codel ip_tables x_tables unix
[ 133.789377][ T788] CPU: 1 PID: 788 Comm: ip Not tainted 5.4.0-rc3+ #96
[ 133.790069][ T788] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 133.791167][ T788] RIP: 0010:rollback_registered_many+0x835/0xc80
[ 133.791906][ T788] Code: 00 4d 85 ff 0f 84 b5 fd ff ff ba c0 0c 00 00 48 89 de 4c 89 ff e8 9b 58 04 00 48 89 df e8 30
[ 133.794317][ T788] RSP: 0018:ffff88805ba3f338 EFLAGS: 00010202
[ 133.795080][ T788] RAX: ffff88805e57e801 RBX: ffff88805ba34000 RCX: ffffffffa9294723
[ 133.796045][ T788] RDX: 1ffff1100b746816 RSI: 0000000000000008 RDI: ffffffffabcc4240
[ 133.797006][ T788] RBP: ffff88805ba3f4c0 R08: fffffbfff5798849 R09: fffffbfff5798849
[ 133.797993][ T788] R10: 0000000000000001 R11: fffffbfff5798848 R12: dffffc0000000000
[ 133.802514][ T788] R13: ffff88805ba3f440 R14: ffff88805ba3f400 R15: ffff88805ed622c0
[ 133.803237][ T788] FS: 00007f2e9608c0c0(0000) GS:ffff88806cc00000(0000) knlGS:0000000000000000
[ 133.804002][ T788] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 133.804664][ T788] CR2: 00007f2e95610603 CR3: 000000005f68c004 CR4: 00000000000606e0
[ 133.805363][ T788] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 133.806073][ T788] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 133.806787][ T788] Call Trace:
[ 133.807069][ T788] ? generic_xdp_install+0x310/0x310
[ 133.807612][ T788] ? lock_acquire+0x164/0x3b0
[ 133.808077][ T788] ? is_bpf_text_address+0x5/0xf0
[ 133.808640][ T788] ? deref_stack_reg+0x9c/0xd0
[ 133.809138][ T788] ? __nla_validate_parse+0x98/0x1ab0
[ 133.809944][ T788] unregister_netdevice_many.part.122+0x13/0x1b0
[ 133.810599][ T788] rtnl_delete_link+0xbc/0x100
[ 133.811073][ T788] ? rtnl_af_register+0xc0/0xc0
[ 133.811672][ T788] rtnl_dellink+0x30e/0x8a0
[ 133.812205][ T788] ? is_bpf_text_address+0x5/0xf0
[ ... ]
[ 144.110530][ T788] unregister_netdevice: waiting for dummy0 to become free. Usage count = 1
This patch adds notifier routine to delete upper interface before deleting
lower interface.
Fixes: c7cdba31ed8b ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes variables and callback these are related to the nested
device structure.
devices that can be nested have their own nest_level variable that
represents the depth of nested devices.
In the previous patch, new {lower/upper}_level variables are added and
they replace old private nest_level variable.
So, this patch removes all 'nest_level' variables.
In order to avoid lockdep warning, ->ndo_get_lock_subclass() was added
to get lockdep subclass value, which is actually lower nested depth value.
But now, they use the dynamic lockdep key to avoid lockdep warning instead
of the subclass.
So, this patch removes ->ndo_get_lock_subclass() callback.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current vxlan code doesn't limit the number of nested devices.
Nested devices would be handled recursively and this routine needs
huge stack memory. So, unlimited nested devices could make
stack overflow.
In order to fix this issue, this patch adds adjacent links.
The adjacent link APIs internally check the depth level.
Test commands:
ip link add dummy0 type dummy
ip link add vxlan0 type vxlan id 0 group 239.1.1.1 dev dummy0 \
dstport 4789
for i in {1..100}
do
let A=$i-1
ip link add vxlan$i type vxlan id $i group 239.1.1.1 \
dev vxlan$A dstport 4789
done
ip link del dummy0
The top upper link is vxlan100 and the lowest link is vxlan0.
When vxlan0 is deleting, the upper devices will be deleted recursively.
It needs huge stack memory so it makes stack overflow.
Splat looks like:
[ 229.628477] =============================================================================
[ 229.629785] BUG page->ptl (Not tainted): Padding overwritten. 0x0000000026abf214-0x0000000091f6abb2
[ 229.629785] -----------------------------------------------------------------------------
[ 229.629785]
[ 229.655439] ==================================================================
[ 229.629785] INFO: Slab 0x00000000ff7cfda8 objects=19 used=19 fp=0x00000000fe33776c flags=0x200000000010200
[ 229.655688] BUG: KASAN: stack-out-of-bounds in unmap_single_vma+0x25a/0x2e0
[ 229.655688] Read of size 8 at addr ffff888113076928 by task vlan-network-in/2334
[ 229.655688]
[ 229.629785] Padding 0000000026abf214: 00 80 14 0d 81 88 ff ff 68 91 81 14 81 88 ff ff ........h.......
[ 229.629785] Padding 0000000001e24790: 38 91 81 14 81 88 ff ff 68 91 81 14 81 88 ff ff 8.......h.......
[ 229.629785] Padding 00000000b39397c8: 33 30 62 a7 ff ff ff ff ff eb 60 22 10 f1 ff 1f 30b.......`"....
[ 229.629785] Padding 00000000bc98f53a: 80 60 07 13 81 88 ff ff 00 80 14 0d 81 88 ff ff .`..............
[ 229.629785] Padding 000000002aa8123d: 68 91 81 14 81 88 ff ff f7 21 17 a7 ff ff ff ff h........!......
[ 229.629785] Padding 000000001c8c2369: 08 81 14 0d 81 88 ff ff 03 02 00 00 00 00 00 00 ................
[ 229.629785] Padding 000000004e290c5d: 21 90 a2 21 10 ed ff ff 00 00 00 00 00 fc ff df !..!............
[ 229.629785] Padding 000000000e25d731: 18 60 07 13 81 88 ff ff c0 8b 13 05 81 88 ff ff .`..............
[ 229.629785] Padding 000000007adc7ab3: b3 8a b5 41 00 00 00 00 ...A....
[ 229.629785] FIX page->ptl: Restoring 0x0000000026abf214-0x0000000091f6abb2=0x5a
[ ... ]
Fixes: acaf4e70997f ("net: vxlan: when lower dev unregisters remove vxlan dev as well")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to link an adjacent node, netdev_upper_dev_link() is used
and in order to unlink an adjacent node, netdev_upper_dev_unlink() is used.
unlink operation does not fail, but link operation can fail.
In order to exchange adjacent nodes, we should unlink an old adjacent
node first. then, link a new adjacent node.
If link operation is failed, we should link an old adjacent node again.
But this link operation can fail too.
It eventually breaks the adjacent link relationship.
This patch adds an ignore flag into the netdev_adjacent structure.
If this flag is set, netdev_upper_dev_link() ignores an old adjacent
node for a moment.
This patch also adds new functions for other modules.
netdev_adjacent_change_prepare()
netdev_adjacent_change_commit()
netdev_adjacent_change_abort()
netdev_adjacent_change_prepare() inserts new device into adjacent list
but new device is not allowed to use immediately.
If netdev_adjacent_change_prepare() fails, it internally rollbacks
adjacent list so that we don't need any other action.
netdev_adjacent_change_commit() deletes old device in the adjacent list
and allows new device to use.
netdev_adjacent_change_abort() rollbacks adjacent list.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a macsec interface is created, it increases a refcnt to a lower
device(real device). when macsec interface is deleted, the refcnt is
decreased in macsec_free_netdev(), which is ->priv_destructor() of
macsec interface.
The problem scenario is this.
When nested macsec interfaces are exiting, the exit routine of the
macsec module makes refcnt leaks.
Test commands:
ip link add dummy0 type dummy
ip link add macsec0 link dummy0 type macsec
ip link add macsec1 link macsec0 type macsec
modprobe -rv macsec
[ 208.629433] unregister_netdevice: waiting for macsec0 to become free. Usage count = 1
Steps of exit routine of macsec module are below.
1. Calls ->dellink() in __rtnl_link_unregister().
2. Checks refcnt and wait refcnt to be 0 if refcnt is not 0 in
netdev_run_todo().
3. Calls ->priv_destruvtor() in netdev_run_todo().
Step2 checks refcnt, but step3 decreases refcnt.
So, step2 waits forever.
This patch makes the macsec module do not hold a refcnt of the lower
device because it already holds a refcnt of the lower device with
netdev_upper_dev_link().
Fixes: c09440f7dcb3 ("macsec: introduce IEEE 802.1AE driver")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
team interface could be nested and it's lock variable could be nested too.
But this lock uses static lockdep key and there is no nested locking
handling code such as mutex_lock_nested() and so on.
so the Lockdep would warn about the circular locking scenario that
couldn't happen.
In order to fix, this patch makes the team module to use dynamic lock key
instead of static key.
Test commands:
ip link add team0 type team
ip link add team1 type team
ip link set team0 master team1
ip link set team0 nomaster
ip link set team1 master team0
ip link set team1 nomaster
Splat that looks like:
[ 40.364352] WARNING: possible recursive locking detected
[ 40.364964] 5.4.0-rc3+ #96 Not tainted
[ 40.365405] --------------------------------------------
[ 40.365973] ip/750 is trying to acquire lock:
[ 40.366542] ffff888060b34c40 (&team->lock){+.+.}, at: team_set_mac_address+0x151/0x290 [team]
[ 40.367689]
but task is already holding lock:
[ 40.368729] ffff888051201c40 (&team->lock){+.+.}, at: team_del_slave+0x29/0x60 [team]
[ 40.370280]
other info that might help us debug this:
[ 40.371159] Possible unsafe locking scenario:
[ 40.371942] CPU0
[ 40.372338] ----
[ 40.372673] lock(&team->lock);
[ 40.373115] lock(&team->lock);
[ 40.373549]
*** DEADLOCK ***
[ 40.374432] May be due to missing lock nesting notation
[ 40.375338] 2 locks held by ip/750:
[ 40.375851] #0: ffffffffabcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0
[ 40.376927] #1: ffff888051201c40 (&team->lock){+.+.}, at: team_del_slave+0x29/0x60 [team]
[ 40.377989]
stack backtrace:
[ 40.378650] CPU: 0 PID: 750 Comm: ip Not tainted 5.4.0-rc3+ #96
[ 40.379368] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 40.380574] Call Trace:
[ 40.381208] dump_stack+0x7c/0xbb
[ 40.381959] __lock_acquire+0x269d/0x3de0
[ 40.382817] ? register_lock_class+0x14d0/0x14d0
[ 40.383784] ? check_chain_key+0x236/0x5d0
[ 40.384518] lock_acquire+0x164/0x3b0
[ 40.385074] ? team_set_mac_address+0x151/0x290 [team]
[ 40.385805] __mutex_lock+0x14d/0x14c0
[ 40.386371] ? team_set_mac_address+0x151/0x290 [team]
[ 40.387038] ? team_set_mac_address+0x151/0x290 [team]
[ 40.387632] ? mutex_lock_io_nested+0x1380/0x1380
[ 40.388245] ? team_del_slave+0x60/0x60 [team]
[ 40.388752] ? rcu_read_lock_sched_held+0x90/0xc0
[ 40.389304] ? rcu_read_lock_bh_held+0xa0/0xa0
[ 40.389819] ? lock_acquire+0x164/0x3b0
[ 40.390285] ? lockdep_rtnl_is_held+0x16/0x20
[ 40.390797] ? team_port_get_rtnl+0x90/0xe0 [team]
[ 40.391353] ? __module_text_address+0x13/0x140
[ 40.391886] ? team_set_mac_address+0x151/0x290 [team]
[ 40.392547] team_set_mac_address+0x151/0x290 [team]
[ 40.393111] dev_set_mac_address+0x1f0/0x3f0
[ ... ]
Fixes: 3d249d4ca7d0 ("net: introduce ethernet teaming device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All bonding device has same lockdep key and subclass is initialized with
nest_level.
But actual nest_level value can be changed when a lower device is attached.
And at this moment, the subclass should be updated but it seems to be
unsafe.
So this patch makes bonding use dynamic lockdep key instead of the
subclass.
Test commands:
ip link add bond0 type bond
for i in {1..5}
do
let A=$i-1
ip link add bond$i type bond
ip link set bond$i master bond$A
done
ip link set bond5 master bond0
Splat looks like:
[ 307.992912] WARNING: possible recursive locking detected
[ 307.993656] 5.4.0-rc3+ #96 Tainted: G W
[ 307.994367] --------------------------------------------
[ 307.995092] ip/761 is trying to acquire lock:
[ 307.995710] ffff8880513aac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.997045]
but task is already holding lock:
[ 307.997923] ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 307.999215]
other info that might help us debug this:
[ 308.000251] Possible unsafe locking scenario:
[ 308.001137] CPU0
[ 308.001533] ----
[ 308.001915] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.002609] lock(&(&bond->stats_lock)->rlock#2/2);
[ 308.003302]
*** DEADLOCK ***
[ 308.004310] May be due to missing lock nesting notation
[ 308.005319] 3 locks held by ip/761:
[ 308.005830] #0: ffffffff9fcc42b0 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x466/0x8a0
[ 308.006894] #1: ffff88805fcbac60 (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0xb8/0x500 [bonding]
[ 308.008243] #2: ffffffff9f9219c0 (rcu_read_lock){....}, at: bond_get_stats+0x9f/0x500 [bonding]
[ 308.009422]
stack backtrace:
[ 308.010124] CPU: 0 PID: 761 Comm: ip Tainted: G W 5.4.0-rc3+ #96
[ 308.011097] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 308.012179] Call Trace:
[ 308.012601] dump_stack+0x7c/0xbb
[ 308.013089] __lock_acquire+0x269d/0x3de0
[ 308.013669] ? register_lock_class+0x14d0/0x14d0
[ 308.014318] lock_acquire+0x164/0x3b0
[ 308.014858] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.015520] _raw_spin_lock_nested+0x2e/0x60
[ 308.016129] ? bond_get_stats+0xb8/0x500 [bonding]
[ 308.017215] bond_get_stats+0xb8/0x500 [bonding]
[ 308.018454] ? bond_arp_rcv+0xf10/0xf10 [bonding]
[ 308.019710] ? rcu_read_lock_held+0x90/0xa0
[ 308.020605] ? rcu_read_lock_sched_held+0xc0/0xc0
[ 308.021286] ? bond_get_stats+0x9f/0x500 [bonding]
[ 308.021953] dev_get_stats+0x1ec/0x270
[ 308.022508] bond_get_stats+0x1d1/0x500 [bonding]
Fixes: d3fff6c443fe ("net: add netdev_lockdep_set_classes() helper")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IFF_BONDING means bonding master or bonding slave device.
->ndo_add_slave() sets IFF_BONDING flag and ->ndo_del_slave() unsets
IFF_BONDING flag.
bond0<--bond1
Both bond0 and bond1 are bonding device and these should keep having
IFF_BONDING flag until they are removed.
But bond1 would lose IFF_BONDING at ->ndo_del_slave() because that routine
do not check whether the slave device is the bonding type or not.
This patch adds the interface type check routine before removing
IFF_BONDING flag.
Test commands:
ip link add bond0 type bond
ip link add bond1 type bond
ip link set bond1 master bond0
ip link set bond1 nomaster
ip link del bond1 type bond
ip link add bond1 type bond
Splat looks like:
[ 226.665555] proc_dir_entry 'bonding/bond1' already registered
[ 226.666440] WARNING: CPU: 0 PID: 737 at fs/proc/generic.c:361 proc_register+0x2a9/0x3e0
[ 226.667571] Modules linked in: bonding af_packet sch_fq_codel ip_tables x_tables unix
[ 226.668662] CPU: 0 PID: 737 Comm: ip Not tainted 5.4.0-rc3+ #96
[ 226.669508] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 226.670652] RIP: 0010:proc_register+0x2a9/0x3e0
[ 226.671612] Code: 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 39 01 00 00 48 8b 04 24 48 89 ea 48 c7 c7 a0 0b 14 9f 48 8b b0 e
0 00 00 00 e8 07 e7 88 ff <0f> 0b 48 c7 c7 40 2d a5 9f e8 59 d6 23 01 48 8b 4c 24 10 48 b8 00
[ 226.675007] RSP: 0018:ffff888050e17078 EFLAGS: 00010282
[ 226.675761] RAX: dffffc0000000008 RBX: ffff88805fdd0f10 RCX: ffffffff9dd344e2
[ 226.676757] RDX: 0000000000000001 RSI: 0000000000000008 RDI: ffff88806c9f6b8c
[ 226.677751] RBP: ffff8880507160f3 R08: ffffed100d940019 R09: ffffed100d940019
[ 226.678761] R10: 0000000000000001 R11: ffffed100d940018 R12: ffff888050716008
[ 226.679757] R13: ffff8880507160f2 R14: dffffc0000000000 R15: ffffed100a0e2c1e
[ 226.680758] FS: 00007fdc217cc0c0(0000) GS:ffff88806c800000(0000) knlGS:0000000000000000
[ 226.681886] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 226.682719] CR2: 00007f49313424d0 CR3: 0000000050e46001 CR4: 00000000000606f0
[ 226.683727] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 226.684725] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 226.685681] Call Trace:
[ 226.687089] proc_create_seq_private+0xb3/0xf0
[ 226.687778] bond_create_proc_entry+0x1b3/0x3f0 [bonding]
[ 226.691458] bond_netdev_event+0x433/0x970 [bonding]
[ 226.692139] ? __module_text_address+0x13/0x140
[ 226.692779] notifier_call_chain+0x90/0x160
[ 226.693401] register_netdevice+0x9b3/0xd80
[ 226.694010] ? alloc_netdev_mqs+0x854/0xc10
[ 226.694629] ? netdev_change_features+0xa0/0xa0
[ 226.695278] ? rtnl_create_link+0x2ed/0xad0
[ 226.695849] bond_newlink+0x2a/0x60 [bonding]
[ 226.696422] __rtnl_newlink+0xb9f/0x11b0
[ 226.696968] ? rtnl_link_unregister+0x220/0x220
[ ... ]
Fixes: 0b680e753724 ("[PATCH] bonding: Add priv_flag to avoid event mishandling")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some interface types could be nested.
(VLAN, BONDING, TEAM, MACSEC, MACVLAN, IPVLAN, VIRT_WIFI, VXLAN, etc..)
These interface types should set lockdep class because, without lockdep
class key, lockdep always warn about unexisting circular locking.
In the current code, these interfaces have their own lockdep class keys and
these manage itself. So that there are so many duplicate code around the
/driver/net and /net/.
This patch adds new generic lockdep keys and some helper functions for it.
This patch does below changes.
a) Add lockdep class keys in struct net_device
- qdisc_running, xmit, addr_list, qdisc_busylock
- these keys are used as dynamic lockdep key.
b) When net_device is being allocated, lockdep keys are registered.
- alloc_netdev_mqs()
c) When net_device is being free'd llockdep keys are unregistered.
- free_netdev()
d) Add generic lockdep key helper function
- netdev_register_lockdep_key()
- netdev_unregister_lockdep_key()
- netdev_update_lockdep_key()
e) Remove unnecessary generic lockdep macro and functions
f) Remove unnecessary lockdep code of each interfaces.
After this patch, each interface modules don't need to maintain
their lockdep keys.
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current code doesn't limit the number of nested devices.
Nested devices would be handled recursively and this needs huge stack
memory. So, unlimited nested devices could make stack overflow.
This patch adds upper_level and lower_level, they are common variables
and represent maximum lower/upper depth.
When upper/lower device is attached or dettached,
{lower/upper}_level are updated. and if maximum depth is bigger than 8,
attach routine fails and returns -EMLINK.
In addition, this patch converts recursive routine of
netdev_walk_all_{lower/upper} to iterator routine.
Test commands:
ip link add dummy0 type dummy
ip link add link dummy0 name vlan1 type vlan id 1
ip link set vlan1 up
for i in {2..55}
do
let A=$i-1
ip link add vlan$i link vlan$A type vlan id $i
done
ip link del dummy0
Splat looks like:
[ 155.513226][ T908] BUG: KASAN: use-after-free in __unwind_start+0x71/0x850
[ 155.514162][ T908] Write of size 88 at addr ffff8880608a6cc0 by task ip/908
[ 155.515048][ T908]
[ 155.515333][ T908] CPU: 0 PID: 908 Comm: ip Not tainted 5.4.0-rc3+ #96
[ 155.516147][ T908] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 155.517233][ T908] Call Trace:
[ 155.517627][ T908]
[ 155.517918][ T908] Allocated by task 0:
[ 155.518412][ T908] (stack is not available)
[ 155.518955][ T908]
[ 155.519228][ T908] Freed by task 0:
[ 155.519885][ T908] (stack is not available)
[ 155.520452][ T908]
[ 155.520729][ T908] The buggy address belongs to the object at ffff8880608a6ac0
[ 155.520729][ T908] which belongs to the cache names_cache of size 4096
[ 155.522387][ T908] The buggy address is located 512 bytes inside of
[ 155.522387][ T908] 4096-byte region [ffff8880608a6ac0, ffff8880608a7ac0)
[ 155.523920][ T908] The buggy address belongs to the page:
[ 155.524552][ T908] page:ffffea0001822800 refcount:1 mapcount:0 mapping:ffff88806c657cc0 index:0x0 compound_mapcount:0
[ 155.525836][ T908] flags: 0x100000000010200(slab|head)
[ 155.526445][ T908] raw: 0100000000010200 ffffea0001813808 ffffea0001a26c08 ffff88806c657cc0
[ 155.527424][ T908] raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000
[ 155.528429][ T908] page dumped because: kasan: bad access detected
[ 155.529158][ T908]
[ 155.529410][ T908] Memory state around the buggy address:
[ 155.530060][ T908] ffff8880608a6b80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 155.530971][ T908] ffff8880608a6c00: fb fb fb fb fb f1 f1 f1 f1 00 f2 f2 f2 f3 f3 f3
[ 155.531889][ T908] >ffff8880608a6c80: f3 fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 155.532806][ T908] ^
[ 155.533509][ T908] ffff8880608a6d00: fb fb fb fb fb fb fb fb fb f1 f1 f1 f1 00 00 00
[ 155.534436][ T908] ffff8880608a6d80: f2 f3 f3 f3 f3 fb fb fb 00 00 00 00 00 00 00 00
[ ... ]
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If copy_net_ns() failed after net_alloc(), net->key_domain is leaked.
Fix this, by freeing key_domain in error path.
syzbot report:
BUG: memory leak
unreferenced object 0xffff8881175007e0 (size 32):
comm "syz-executor902", pid 7069, jiffies 4294944350 (age 28.400s)
hex dump (first 32 bytes):
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000a83ed741>] kmemleak_alloc_recursive include/linux/kmemleak.h:43 [inline]
[<00000000a83ed741>] slab_post_alloc_hook mm/slab.h:439 [inline]
[<00000000a83ed741>] slab_alloc mm/slab.c:3326 [inline]
[<00000000a83ed741>] kmem_cache_alloc_trace+0x13d/0x280 mm/slab.c:3553
[<0000000059fc92b9>] kmalloc include/linux/slab.h:547 [inline]
[<0000000059fc92b9>] kzalloc include/linux/slab.h:742 [inline]
[<0000000059fc92b9>] net_alloc net/core/net_namespace.c:398 [inline]
[<0000000059fc92b9>] copy_net_ns+0xb2/0x220 net/core/net_namespace.c:445
[<00000000a9d74bbc>] create_new_namespaces+0x141/0x2a0 kernel/nsproxy.c:103
[<000000008047d645>] unshare_nsproxy_namespaces+0x7f/0x100 kernel/nsproxy.c:202
[<000000005993ea6e>] ksys_unshare+0x236/0x490 kernel/fork.c:2674
[<0000000019417e75>] __do_sys_unshare kernel/fork.c:2742 [inline]
[<0000000019417e75>] __se_sys_unshare kernel/fork.c:2740 [inline]
[<0000000019417e75>] __x64_sys_unshare+0x16/0x20 kernel/fork.c:2740
[<00000000f4c5f2c8>] do_syscall_64+0x76/0x1a0 arch/x86/entry/common.c:296
[<0000000038550184>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
syzbot also reported other leak in copy_net_ns -> setup_net.
This problem is already fixed by cf47a0b882a4e5f6b34c7949d7b293e9287f1972.
Fixes: 9b242610514f ("keys: Network namespace domain tag")
Reported-and-tested-by: syzbot+3b3296d032353c33184b@syzkaller.appspotmail.com
Signed-off-by: Takeshi Misawa <jeliantsurux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Payload offload rule should also check the length of the match.
Moreover, check for unsupported link-layer fields:
nft --debug=netlink add rule firewall zones vlan id 100
...
[ payload load 2b @ link header + 0 => reg 1 ]
this loads 2byte base on ll header and offset 0.
This also fixes unsupported raw payload match.
Fixes: 92ad6325cb89 ("netfilter: nf_tables: add hardware offload support")
Signed-off-by: wenxu <wenxu@ucloud.cn>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
syzbot reported the following issue :
BUG: KCSAN: data-race in update_defense_level / update_defense_level
read to 0xffffffff861a6260 of 4 bytes by task 3006 on cpu 1:
update_defense_level+0x621/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:177
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
write to 0xffffffff861a6260 of 4 bytes by task 7333 on cpu 0:
update_defense_level+0xa62/0xb30 net/netfilter/ipvs/ip_vs_ctl.c:205
defense_work_handler+0x3d/0xd0 net/netfilter/ipvs/ip_vs_ctl.c:225
process_one_work+0x3d4/0x890 kernel/workqueue.c:2269
worker_thread+0xa0/0x800 kernel/workqueue.c:2415
kthread+0x1d4/0x200 drivers/block/aoe/aoecmd.c:1253
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Reported by Kernel Concurrency Sanitizer on:
CPU: 0 PID: 7333 Comm: kworker/0:5 Not tainted 5.4.0-rc3+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: events defense_work_handler
Indeed, old_secure_tcp is currently a static variable, while it
needs to be a per netns variable.
Fixes: a0840e2e165a ("IPVS: netns, ip_vs_ctl local vars moved to ipvs struct.")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
if the IPVS module is removed while the sync daemon is starting, there is
a small gap where try_module_get() might fail getting the refcount inside
ip_vs_use_count_inc(). Then, the refcounts of IPVS module are unbalanced,
and the subsequent call to stop_sync_thread() causes the following splat:
WARNING: CPU: 0 PID: 4013 at kernel/module.c:1146 module_put.part.44+0x15b/0x290
Modules linked in: ip_vs(-) nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 veth ip6table_filter ip6_tables iptable_filter binfmt_misc intel_rapl_msr intel_rapl_common crct10dif_pclmul crc32_pclmul ext4 mbcache jbd2 ghash_clmulni_intel snd_hda_codec_generic ledtrig_audio snd_hda_intel snd_intel_nhlt snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm aesni_intel crypto_simd cryptd glue_helper joydev pcspkr snd_timer virtio_balloon snd soundcore i2c_piix4 nfsd auth_rpcgss nfs_acl lockd grace sunrpc ip_tables xfs libcrc32c ata_generic pata_acpi virtio_net net_failover virtio_blk failover virtio_console qxl drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops ata_piix ttm crc32c_intel serio_raw drm virtio_pci libata virtio_ring virtio floppy dm_mirror dm_region_hash dm_log dm_mod [last unloaded: nf_defrag_ipv6]
CPU: 0 PID: 4013 Comm: modprobe Tainted: G W 5.4.0-rc1.upstream+ #741
Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
RIP: 0010:module_put.part.44+0x15b/0x290
Code: 04 25 28 00 00 00 0f 85 18 01 00 00 48 83 c4 68 5b 5d 41 5c 41 5d 41 5e 41 5f c3 89 44 24 28 83 e8 01 89 c5 0f 89 57 ff ff ff <0f> 0b e9 78 ff ff ff 65 8b 1d 67 83 26 4a 89 db be 08 00 00 00 48
RSP: 0018:ffff888050607c78 EFLAGS: 00010297
RAX: 0000000000000003 RBX: ffffffffc1420590 RCX: ffffffffb5db0ef9
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffffc1420590
RBP: 00000000ffffffff R08: fffffbfff82840b3 R09: fffffbfff82840b3
R10: 0000000000000001 R11: fffffbfff82840b2 R12: 1ffff1100a0c0f90
R13: ffffffffc1420200 R14: ffff88804f533300 R15: ffff88804f533ca0
FS: 00007f8ea9720740(0000) GS:ffff888053800000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f3245abe000 CR3: 000000004c28a006 CR4: 00000000001606f0
Call Trace:
stop_sync_thread+0x3a3/0x7c0 [ip_vs]
ip_vs_sync_net_cleanup+0x13/0x50 [ip_vs]
ops_exit_list.isra.5+0x94/0x140
unregister_pernet_operations+0x29d/0x460
unregister_pernet_device+0x26/0x60
ip_vs_cleanup+0x11/0x38 [ip_vs]
__x64_sys_delete_module+0x2d5/0x400
do_syscall_64+0xa5/0x4e0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x7f8ea8bf0db7
Code: 73 01 c3 48 8b 0d b9 80 2c 00 f7 d8 64 89 01 48 83 c8 ff c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 b8 b0 00 00 00 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 89 80 2c 00 f7 d8 64 89 01 48
RSP: 002b:00007ffcd38d2fe8 EFLAGS: 00000206 ORIG_RAX: 00000000000000b0
RAX: ffffffffffffffda RBX: 0000000002436240 RCX: 00007f8ea8bf0db7
RDX: 0000000000000000 RSI: 0000000000000800 RDI: 00000000024362a8
RBP: 0000000000000000 R08: 00007f8ea8eba060 R09: 00007f8ea8c658a0
R10: 00007ffcd38d2a60 R11: 0000000000000206 R12: 0000000000000000
R13: 0000000000000001 R14: 00000000024362a8 R15: 0000000000000000
irq event stamp: 4538
hardirqs last enabled at (4537): [<ffffffffb6193dde>] quarantine_put+0x9e/0x170
hardirqs last disabled at (4538): [<ffffffffb5a0556a>] trace_hardirqs_off_thunk+0x1a/0x20
softirqs last enabled at (4522): [<ffffffffb6f8ebe9>] sk_common_release+0x169/0x2d0
softirqs last disabled at (4520): [<ffffffffb6f8eb3e>] sk_common_release+0xbe/0x2d0
Check the return value of ip_vs_use_count_inc() and let its caller return
proper error. Inside do_ip_vs_set_ctl() the module is already refcounted,
we don't need refcount/derefcount there. Finally, in register_ip_vs_app()
and start_sync_thread(), take the module refcount earlier and ensure it's
released in the error path.
Change since v1:
- better return values in case of failure of ip_vs_use_count_inc(),
thanks to Julian Anastasov
- no need to increase/decrease the module refcount in ip_vs_set_ctl(),
thanks to Julian Anastasov
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Simon Horman <horms@verge.net.au>
|
|
The LAN8740, like the 8720, also requires a reset after enabling clock.
The datasheet [1] 3.8.5.1 says:
"During a Hardware reset, an external clock must be supplied
to the XTAL1/CLKIN signal."
I have observed this issue on a custom i.MX6 based board with
the LAN8740A.
[1] http://ww1.microchip.com/downloads/en/DeviceDoc/8740a.pdf
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Having Rx-only AF_XDP sockets can potentially lead to a crash in the
system by a NULL pointer dereference in xsk_umem_consume_tx(). This
function iterates through a list of all sockets tied to a umem and
checks if there are any packets to send on the Tx ring. Rx-only
sockets do not have a Tx ring, so this will cause a NULL pointer
dereference. This will happen if you have registered one or more
Rx-only sockets to a umem and the driver is checking the Tx ring even
on Rx, or if the XDP_SHARED_UMEM mode is used and there is a mix of
Rx-only and other sockets tied to the same umem.
Fixed by only putting sockets with a Tx component on the list that
xsk_umem_consume_tx() iterates over.
Fixes: ac98d8aab61b ("xsk: wire upp Tx zero-copy functions")
Reported-by: Kal Cutter Conley <kal.conley@dectris.com>
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Link: https://lore.kernel.org/bpf/1571645818-16244-1-git-send-email-magnus.karlsson@intel.com
|
|
UDP IPv6 packets auto flowlabels are using a 32bit secret
(static u32 hashrnd in net/core/flow_dissector.c) and
apply jhash() over fields known by the receivers.
Attackers can easily infer the 32bit secret and use this information
to identify a device and/or user, since this 32bit secret is only
set at boot time.
Really, using jhash() to generate cookies sent on the wire
is a serious security concern.
Trying to change the rol32(hash, 16) in ip6_make_flowlabel() would be
a dead end. Trying to periodically change the secret (like in sch_sfq.c)
could change paths taken in the network for long lived flows.
Let's switch to siphash, as we did in commit df453700e8d8
("inet: switch IP ID generator to siphash")
Using a cryptographically strong pseudo random function will solve this
privacy issue and more generally remove other weak points in the stack.
Packet schedulers using skb_get_hash_perturb() benefit from this change.
Fixes: b56774163f99 ("ipv6: Enable auto flow labels by default")
Fixes: 42240901f7c4 ("ipv6: Implement different admin modes for automatic flow labels")
Fixes: 67800f9b1f4e ("ipv6: Call skb_get_hash_flowi6 to get skb->hash in ip6_make_flowlabel")
Fixes: cb1ce2ef387b ("ipv6: Implement automatic flow label generation on transmit")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Berger <jonathann1@walla.com>
Reported-by: Amit Klein <aksecurity@gmail.com>
Reported-by: Benny Pinkas <benny@pinkas.net>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Anson Huang
Jakub Kicinski
Xin Long
Jiangfeng Xiao
Eran Ben Elisha
Vladimir Oltean
Navid Emamdoost
Will Deacon
Daniel Wagner
Arnd Bergmann
Benjamin Herrenschmidt
Tejun Heo
Eric Dumazet
Nishad Kamdar
Paolo Abeni
zhanglin
Raju Rangoju
Guillaume Nault
Ursula Braun
Ben Dooks (Codethink)
Vincent Prince
Taehee Yoo
Takeshi Misawa
wenxu
Davide Caratti
Martin Fuzzey
Magnus Karlsson