| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On SAM9X60, slewrate should be enabled on pins with a switching frequency
below 50Mhz. Since most of our pins do not exceed this value, we enable
slewrate by default. Pins with a switching value that exceeds 50Mhz will
have to explicitly disable slewrate.
This patch changes the ABI. However, the slewrate macros are only used
by SAM9X60 and, at this moment, there are no device-tree files available
for this platform.
Suggested-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Link: https://lore.kernel.org/r/20191101092031.24896-1-codrin.ciubotariu@microchip.com
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
pinctrl: sh-pfc: Updates for v5.5 (take two)
- Add support for the new R-Car M3-W+ (r8a77961) SoC,
- Small fixes and cleanups.
|
|
The definitions for bit field [19:18] of the Peripheral Function Select
Register 3 were accidentally copied from bit field [20], leading to
duplicates for the TCLK1_B function, and missing TCLK0, CAN_CLK_B, and
ET0_ETXD4 functions.
Fix this by adding the missing GPIO_FN_CAN_CLK_B and GPIO_FN_ET0_ETXD4
enum values, and correcting the functions.
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191024131308.16659-1-geert+renesas@glider.be
|
|
Add support for the Pin Function Controller in the R-Car M3-W+
(R8A77961) SoC.
R-Car M3-W+ is pin compatible with R-Car M3-W (R8A77960), which allows
for both SoCs to share a driver.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-4-geert+renesas@glider.be
|
|
Rename CONFIG_PINCTRL_PFC_R8A7796 for R-Car M3-W (R8A77960) to
CONFIG_PINCTRL_PFC_R8A77960, to avoid confusion with R-Car M3-W+
(R8A77961), which will use CONFIG_PINCTRL_PFC_R8A77961.
Extend the dependency of CONFIG_PINCTRL_PFC_R8A77960 from
CONFIG_ARCH_R8A7796 to CONFIG_ARCH_R8A77960, to relax dependencies for a
future rename of the SoC configuration symbol.
Rename r8a7796_pinmux_info to r8a77960_pinmux_info, as it contains an
r8a77960-based name.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191023122955.12420-3-geert+renesas@glider.be
|
|
As platform_get_irq() now prints an error when the interrupt does not
exist, counting interrupts by looping until failure causes the printing
of scary messages like:
sh-pfc e6060000.pin-controller: IRQ index 0 not found
Fix this by using the platform_irq_count() helper instead.
Fixes: 7723f4c5ecdb8d83 ("driver core: platform: Add an error message to platform_get_irq*()")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20191016142601.28255-1-geert+renesas@glider.be
|
|
pinctrl: sh-pfc: Updates for v5.5
- Add support for the new RZ/G2N (r8a774b1) SoC,
- Small fixes and cleanups.
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191016141217.21520-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20191016141053.23740-1-yuehaibing@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Linux 5.4-rc4
|
|
Pull irq fixes from Thomas Gleixner:
"A small set of irq chip driver fixes and updates:
- Update the SIFIVE PLIC interrupt driver to use the fasteoi handler
to address the shortcomings of the existing flow handling which was
prone to lose interrupts
- Use the proper limit for GIC interrupt line numbers
- Add retrigger support for the recently merged Anapurna Labs Fabric
interrupt controller to make it complete
- Enable the ATMEL AIC5 interrupt controller driver on the new
SAM9X60 SoC"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/sifive-plic: Switch to fasteoi flow
irqchip/gic-v3: Fix GIC_LINE_NR accessor
irqchip/atmel-aic5: Add support for sam9x60 irqchip
irqchip/al-fic: Add support for irq retrigger
|
|
Pull networking fixes from David Miller:
"I was battling a cold after some recent trips, so quite a bit piled up
meanwhile, sorry about that.
Highlights:
1) Fix fd leak in various bpf selftests, from Brian Vazquez.
2) Fix crash in xsk when device doesn't support some methods, from
Magnus Karlsson.
3) Fix various leaks and use-after-free in rxrpc, from David Howells.
4) Fix several SKB leaks due to confusion of who owns an SKB and who
should release it in the llc code. From Eric Biggers.
5) Kill a bunc of KCSAN warnings in TCP, from Eric Dumazet.
6) Jumbo packets don't work after resume on r8169, as the BIOS resets
the chip into non-jumbo mode during suspend. From Heiner Kallweit.
7) Corrupt L2 header during MPLS push, from Davide Caratti.
8) Prevent possible infinite loop in tc_ctl_action, from Eric
Dumazet.
9) Get register bits right in bcmgenet driver, based upon chip
version. From Florian Fainelli.
10) Fix mutex problems in microchip DSA driver, from Marek Vasut.
11) Cure race between route lookup and invalidation in ipv4, from Wei
Wang.
12) Fix performance regression due to false sharing in 'net'
structure, from Eric Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (145 commits)
net: reorder 'struct net' fields to avoid false sharing
net: dsa: fix switch tree list
net: ethernet: dwmac-sun8i: show message only when switching to promisc
net: aquantia: add an error handling in aq_nic_set_multicast_list
net: netem: correct the parent's backlog when corrupted packet was dropped
net: netem: fix error path for corrupted GSO frames
macb: propagate errors when getting optional clocks
xen/netback: fix error path of xenvif_connect_data()
net: hns3: fix mis-counting IRQ vector numbers issue
net: usb: lan78xx: Connect PHY before registering MAC
vsock/virtio: discard packets if credit is not respected
vsock/virtio: send a credit update when buffer size is changed
mlxsw: spectrum_trap: Push Ethernet header before reporting trap
net: ensure correct skb->tstamp in various fragmenters
net: bcmgenet: reset 40nm EPHY on energy detect
net: bcmgenet: soft reset 40nm EPHYs before MAC init
net: phy: bcm7xxx: define soft_reset for 40nm EPHY
net: bcmgenet: don't set phydev->link from MAC
net: Update address for MediaTek ethernet driver in MAINTAINERS
ipv4: fix race condition between route lookup and invalidation
...
|
|
Printing the info message every time more than the max number of mac
addresses are requested generates unnecessary log spam. Showing it only
when the hw is not already in promiscous mode is equally informative
without being annoying.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add an error handling in aq_nic_set_multicast_list, it may not
work when hw_multicast_list_set error; and at the same time
it will remove gcc Wunused-but-set-variable warning.
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Reviewed-by: Igor Russkikh <igor.russkikh@aquantia.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_clk, rx_clk, and tsu_clk are optional. Currently the macb driver
marks clock as not available if it receives an error when trying to get
a clock. This is wrong, because a clock controller might return
-EPROBE_DEFER if a clock is not available, but will eventually become
available.
In these cases, the driver would probe successfully but will never be
able to adjust the clocks, because the clocks were not available during
probe, but became available later.
For example, the clock controller for the ZynqMP is implemented in the
PMU firmware and the clocks are only available after the firmware driver
has been probed.
Use devm_clk_get_optional() in instead of devm_clk_get() to get the
optional clock and propagate all errors to the calling function.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Tested-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
xenvif_connect_data() calls module_put() in case of error. This is
wrong as there is no related module_get().
Remove the superfluous module_put().
Fixes: 279f438e36c0a7 ("xen-netback: Don't destroy the netdev until the vif is shut down")
Cc: <stable@vger.kernel.org> # 3.12
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Paul Durrant <paul@xen.org>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the num_msi_left means the vector numbers of NIC,
but if the PF supported RoCE, it contains the vector numbers
of NIC and RoCE(Not expected).
This may cause interrupts lost in some case, because of the
NIC module used the vector resources which belongs to RoCE.
This patch adds a new variable num_nic_msi to store the vector
numbers of NIC, and adjust the default TQP numbers and rss_size
according to the value of num_nic_msi.
Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc fixes from Andrew Morton:
"Rather a lot of fixes, almost all affecting mm/"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (26 commits)
scripts/gdb: fix debugging modules on s390
kernel/events/uprobes.c: only do FOLL_SPLIT_PMD for uprobe register
mm/thp: allow dropping THP from page cache
mm/vmscan.c: support removing arbitrary sized pages from mapping
mm/thp: fix node page state in split_huge_page_to_list()
proc/meminfo: fix output alignment
mm/init-mm.c: include <linux/mman.h> for vm_committed_as_batch
mm/filemap.c: include <linux/ramfs.h> for generic_file_vm_ops definition
mm: include <linux/huge_mm.h> for is_vma_temporary_stack
zram: fix race between backing_dev_show and backing_dev_store
mm/memcontrol: update lruvec counters in mem_cgroup_move_account
ocfs2: fix panic due to ocfs2_wq is null
hugetlbfs: don't access uninitialized memmaps in pfn_range_valid_gigantic()
mm: memblock: do not enforce current limit for memblock_phys* family
mm: memcg: get number of pages on the LRU list in memcgroup base on lru_zone_size
mm/gup: fix a misnamed "write" argument, and a related bug
mm/gup_benchmark: add a missing "w" to getopt string
ocfs2: fix error handling in ocfs2_setattr()
mm: memcg/slab: fix panic in __free_slab() caused by premature memcg pointer release
mm/memunmap: don't access uninitialized memmap in memunmap_pages()
...
|
|
CPU0: CPU1:
backing_dev_show backing_dev_store
...... ......
file = zram->backing_dev;
down_read(&zram->init_lock); down_read(&zram->init_init_lock)
file_path(file, ...); zram->backing_dev = backing_dev;
up_read(&zram->init_lock); up_read(&zram->init_lock);
gets the value of zram->backing_dev too early in backing_dev_show, which
resultin the value being NULL at the beginning, and not NULL later.
backtrace:
d_path+0xcc/0x174
file_path+0x10/0x18
backing_dev_show+0x40/0xb4
dev_attr_show+0x20/0x54
sysfs_kf_seq_show+0x9c/0x10c
kernfs_seq_show+0x28/0x30
seq_read+0x184/0x488
kernfs_fop_read+0x5c/0x1a4
__vfs_read+0x44/0x128
vfs_read+0xa0/0x138
SyS_read+0x54/0xb4
Link: http://lkml.kernel.org/r/1571046839-16814-1-git-send-email-chenwandun@huawei.com
Signed-off-by: Chenwandun <chenwandun@huawei.com>
Acked-by: Minchan Kim <minchan@kernel.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky.work@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org> [4.14+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Uninitialized memmaps contain garbage and in the worst case trigger kernel
BUGs, especially with CONFIG_PAGE_POISONING. They should not get touched.
Right now, when trying to soft-offline a PFN that resides on a memory
block that was never onlined, one gets a misleading error with
CONFIG_PAGE_POISONING:
:/# echo 5637144576 > /sys/devices/system/memory/soft_offline_page
[ 23.097167] soft offline: 0x150000 page already poisoned
But the actual result depends on the garbage in the memmap.
soft_offline_page() can only work with online pages, it returns -EIO in
case of ZONE_DEVICE. Make sure to only forward pages that are online
(iow, managed by the buddy) and, therefore, have an initialized memmap.
Add a check against pfn_to_online_page() and similarly return -EIO.
Link: http://lkml.kernel.org/r/20191010141200.8985-1-david@redhat.com
Fixes: f1dd2cd13c4b ("mm, memory_hotplug: do not associate hotadded memory to zones until online") [visible after d0dc12e86b319]
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: <stable@vger.kernel.org> [4.13+]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request from Keith that address deadlocks, double resets,
memory leaks, and other regression.
- Fixup elv_support_iosched() for bio based devices (Damien)
- Fixup for the ahci PCS quirk (Dan)
- Socket O_NONBLOCK handling fix for io_uring (me)
- Timeout sequence io_uring fixes (yangerkun)
- MD warning fix for parameter default_layout (Song)
- blkcg activation fixes (Tejun)
- blk-rq-qos node deletion fix (Tejun)
* tag 'for-linus-2019-10-18' of git://git.kernel.dk/linux-block:
nvme-pci: Set the prp2 correctly when using more than 4k page
io_uring: fix logic error in io_timeout
io_uring: fix up O_NONBLOCK handling for sockets
md/raid0: fix warning message for parameter default_layout
libata/ahci: Fix PCS quirk application
blk-rq-qos: fix first node deletion of rq_qos_del()
blkcg: Fix multiple bugs in blkcg_activate_policy()
io_uring: consider the overflow of sequence for timeout req
nvme-tcp: fix possible leakage during error flow
nvmet-loop: fix possible leakage during error flow
block: Fix elv_support_iosched()
nvme-tcp: Initialize sk->sk_ll_usec only with NET_RX_BUSY_POLL
nvme: Wait for reset state when required
nvme: Prevent resets during paused controller state
nvme: Restart request timers in resetting state
nvme: Remove ADMIN_ONLY state
nvme-pci: Free tagset if no IO queues
nvme: retain split access workaround for capability reads
nvme: fix possible deadlock when nvme_update_formats fails
|
|
Pull ceph fixes from Ilya Dryomov:
"A future-proofing decoding fix from Jeff intended for stable and a
patch for a mostly benign race from Dongsheng"
* tag 'ceph-for-5.4-rc4' of git://github.com/ceph/ceph-client:
rbd: cancel lock_dwork if the wait is interrupted
ceph: just skip unrecognized info in ceph_reply_info_extra
|
|
Pull device mapper fixes from Mike Snitzer:
- Fix DM snapshot deadlock that can occur due to COW throttling
preventing locks from being released.
- Fix DM cache's GFP_NOWAIT allocation failure error paths by switching
to GFP_NOIO.
- Make __hash_find() static in the DM clone target.
* tag 'for-5.4/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix bugs when a GFP_NOWAIT allocation fails
dm snapshot: rework COW throttling to fix deadlock
dm snapshot: introduce account_start_copy() and account_end_copy()
dm clone: Make __hash_find static
|
|
Pull iommu fixes from Joerg Roedel:
- Fixes for page-table issues on Mali GPUs
- Missing free in an error path for ARM-SMMU
- PASID decoding in the AMD IOMMU Event log code
- Another update for the locking fixes in the AMD IOMMU driver
- Reduce the calls to platform_get_irq() in the IPMMU-VMSA and Rockchip
IOMMUs to get rid of the warning message added to this function
recently
* tag 'iommu-fixes-v5.4-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Check PM_LEVEL_SIZE() condition in locked section
iommu/amd: Fix incorrect PASID decoding from event log
iommu/ipmmu-vmsa: Only call platform_get_irq() when interrupt is mandatory
iommu/rockchip: Don't use platform_get_irq to implicitly count irqs
iommu/io-pgtable-arm: Support all Mali configurations
iommu/io-pgtable-arm: Correct Mali attributes
iommu/arm-smmu: Free context bitmap in the err path of arm_smmu_init_domain_context
|
|
As soon as the netdev is registers, the kernel can start using the
interface. If the driver connects the MAC to the PHY after the netdev
is registered, there is a race condition where the interface can be
opened without having the PHY connected.
Change the order to close this race condition.
Fixes: 92571a1aae40 ("lan78xx: Connect phy early")
Reported-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devlink maintains packets and bytes statistics for each trap. Since
eth_type_trans() was called to set the skb's protocol, the data pointer
no longer points to the start of the packet and the bytes accounting is
off by 14 bytes.
Fix this by pushing the skb's data pointer to the start of the packet.
Fixes: b5ce611fd96e ("mlxsw: spectrum: Add devlink-trap support")
Reported-by: Alex Kushnarov <alexanderk@mellanox.com>
Tested-by: Alex Kushnarov <alexanderk@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull MMC fixes from Ulf Hansson:
"MMC host:
- sdhci-iproc: Prevent some spurious interrupts
- renesas_sdhi/sh_mmcif: Avoid false warnings about IRQs not found
MEMSTICK host:
- jmb38x_ms: Fix an error handling path at ->probe()"
* tag 'mmc-v5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
memstick: jmb38x_ms: Fix an error handling path in 'jmb38x_ms_probe()'
mmc: sdhci-iproc: fix spurious interrupts on Multiblock reads with bcm2711
mmc: sh_mmcif: Use platform_get_irq_optional() for optional interrupt
mmc: renesas_sdhi: Do not use platform_get_irq() to count interrupts
|
|
The EPHY integrated into the 40nm Set-Top Box devices can falsely
detect energy when connected to a disabled peer interface. When the
peer interface is enabled the EPHY will detect and report the link
as active, but on occasion may get into a state where it is not
able to exchange data with the connected GENET MAC. This issue has
not been observed when the link parameters are auto-negotiated;
however, it has been observed with a manually configured link.
It has been empirically determined that issuing a soft reset to the
EPHY when energy is detected prevents it from getting into this bad
state.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It turns out that the "Workaround for putting the PHY in IDDQ mode"
used by the internal EPHYs on 40nm Set-Top Box chips when powering
down puts the interface to the GENET MAC in a state that can cause
subsequent MAC resets to be incomplete.
Rather than restore the forced soft reset when powering up internal
PHYs, this commit moves the invocation of phy_init_hw earlier in
the MAC initialization sequence to just before the MAC reset in the
open and resume functions. This allows the interface to be stable
and allows the MAC resets to be successful.
The bcmgenet_mii_probe() function is split in two to accommodate
this. The new function bcmgenet_mii_connect() handles the first
half of the functionality before the MAC initialization, and the
bcmgenet_mii_config() function is extended to provide the remaining
PHY configuration following the MAC initialization.
Fixes: 484bfa1507bf ("Revert "net: bcmgenet: Software reset EPHY after power on"")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.
This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When commit 28b2e0d2cd13 ("net: phy: remove parameter new_link from
phy_mac_interrupt()") removed the new_link parameter it set the
phydev->link state from the MAC before invoking phy_mac_interrupt().
However, once commit 88d6272acaaa ("net: phy: avoid unneeded MDIO
reads in genphy_read_status") was added this initialization prevents
the proper determination of the connection parameters by the function
genphy_read_status().
This commit removes that initialization to restore the proper
functionality.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull ACPI fixes from Rafael Wysocki:
"Fix possible use-after-free in the ACPI CPPC support code (John Garry)
and prevent the ACPI HMAT parsing code from using possibly incorrect
data coming from the platform firmware (Daniel Black)"
* tag 'acpi-5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: CPPC: Set pcc_data[pcc_ss_id] to NULL in acpi_cppc_processor_exit()
ACPI: HMAT: ACPI_HMAT_MEMORY_PD_VALID is deprecated since ACPI-6.3
|
|
Pull power management fixes from Rafael Wysocki:
"These include a fix for a recent regression in the ACPI CPU
performance scaling code, a PCI device power management fix,
a system shutdown fix related to cpufreq, a removal of an ACPI
suspend-to-idle blacklist entry and a build warning fix.
Specifics:
- Fix possible NULL pointer dereference in the ACPI processor scaling
initialization code introduced by a recent cpufreq update (Rafael
Wysocki).
- Fix possible deadlock due to suspending cpufreq too late during
system shutdown (Rafael Wysocki).
- Make the PCI device system resume code path be more consistent with
its PM-runtime counterpart to fix an issue with missing delay on
transitions from D3cold to D0 during system resume from
suspend-to-idle on some systems (Rafael Wysocki).
- Drop Dell XPS13 9360 from the LPS0 Idle _DSM blacklist to make it
use suspend-to-idle by default (Mario Limonciello).
- Fix build warning in the core system suspend support code (Ben
Dooks)"
* tag 'pm-5.4-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: processor: Avoid NULL pointer dereferences at init time
PCI: PM: Fix pci_power_up()
PM: sleep: include <linux/pm_runtime.h> for pm_wq
cpufreq: Avoid cpufreq_suspend() deadlock on system shutdown
ACPI: PM: Drop Dell XPS13 9360 from LPS0 Idle _DSM blacklist
|
|
Pull scsi fixes from Martin Petersen:
"These two commits were in a separate postmerge branch due to a
dependency on changes merged for 5.4 in the block tree.
They fix two issues in the intersection of the request cleanup changes
from block (b7e9e1fb7a92) and the request batching changes
(8930a6c20791) that were made to SCSI during the 5.4 cycle"
* tag 'mkp-scsi-postmerge' of git://git.kernel.org/pub/scm/linux/kernel/git/mkp/scsi:
scsi: core: fix dh and multipathing for SCSI hosts without request batching
scsi: core: fix missing .cleanup_rq for SCSI hosts without request batching
|
|
The increase_address_space() function has to check the PM_LEVEL_SIZE()
condition again under the domain->lock to avoid a false trigger of the
WARN_ON_ONCE() and to avoid that the address space is increase more
often than necessary.
Reported-by: Qian Cai <cai@lca.pw>
Fixes: 754265bcab78 ("iommu/amd: Fix race in increase_address_space()")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Pull NVMe updates from Keith:
"This is a collection of bug fixes committed since the previous pull
request that address deadlocks, double resets, memory leaks, and other
regression."
* 'nvme-5.4' of git://git.infradead.org/nvme:
nvme-pci: Set the prp2 correctly when using more than 4k page
nvme-tcp: fix possible leakage during error flow
nvmet-loop: fix possible leakage during error flow
nvme-tcp: Initialize sk->sk_ll_usec only with NET_RX_BUSY_POLL
nvme: Wait for reset state when required
nvme: Prevent resets during paused controller state
nvme: Restart request timers in resetting state
nvme: Remove ADMIN_ONLY state
nvme-pci: Free tagset if no IO queues
nvme: retain split access workaround for capability reads
nvme: fix possible deadlock when nvme_update_formats fails
|
|
In the current code, the nvme is using a fixed 4k PRP entry size,
but if the kernel use a page size which is more than 4k, we should
consider the situation that the bv_offset may be larger than the
dev->ctrl.page_size. Otherwise we may miss setting the prp2 and then
cause the command can't be executed correctly.
Fixes: dff824b2aadb ("nvme-pci: optimize mapping of small single segment requests")
Cc: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
* acpi-tables:
ACPI: HMAT: ACPI_HMAT_MEMORY_PD_VALID is deprecated since ACPI-6.3
|
|
When enabling KASAN and DEBUG_TEST_DRIVER_REMOVE, I find this KASAN
warning:
[ 20.872057] BUG: KASAN: use-after-free in pcc_data_alloc+0x40/0xb8
[ 20.878226] Read of size 4 at addr ffff00236cdeb684 by task swapper/0/1
[ 20.884826]
[ 20.886309] CPU: 19 PID: 1 Comm: swapper/0 Not tainted 5.4.0-rc1-00009-ge7f7df3db5bf-dirty #289
[ 20.894994] Hardware name: Huawei D06 /D06, BIOS Hisilicon D06 UEFI RC0 - V1.16.01 03/15/2019
[ 20.903505] Call trace:
[ 20.905942] dump_backtrace+0x0/0x200
[ 20.909593] show_stack+0x14/0x20
[ 20.912899] dump_stack+0xd4/0x130
[ 20.916291] print_address_description.isra.9+0x6c/0x3b8
[ 20.921592] __kasan_report+0x12c/0x23c
[ 20.925417] kasan_report+0xc/0x18
[ 20.928808] __asan_load4+0x94/0xb8
[ 20.932286] pcc_data_alloc+0x40/0xb8
[ 20.935938] acpi_cppc_processor_probe+0x4e8/0xb08
[ 20.940717] __acpi_processor_start+0x48/0xb0
[ 20.945062] acpi_processor_start+0x40/0x60
[ 20.949235] really_probe+0x118/0x548
[ 20.952887] driver_probe_device+0x7c/0x148
[ 20.957059] device_driver_attach+0x94/0xa0
[ 20.961231] __driver_attach+0xa4/0x110
[ 20.965055] bus_for_each_dev+0xe8/0x158
[ 20.968966] driver_attach+0x30/0x40
[ 20.972531] bus_add_driver+0x234/0x2f0
[ 20.976356] driver_register+0xbc/0x1d0
[ 20.980182] acpi_processor_driver_init+0x40/0xe4
[ 20.984875] do_one_initcall+0xb4/0x254
[ 20.988700] kernel_init_freeable+0x24c/0x2f8
[ 20.993047] kernel_init+0x10/0x118
[ 20.996524] ret_from_fork+0x10/0x18
[ 21.000087]
[ 21.001567] Allocated by task 1:
[ 21.004785] save_stack+0x28/0xc8
[ 21.008089] __kasan_kmalloc.isra.9+0xbc/0xd8
[ 21.012435] kasan_kmalloc+0xc/0x18
[ 21.015913] pcc_data_alloc+0x94/0xb8
[ 21.019564] acpi_cppc_processor_probe+0x4e8/0xb08
[ 21.024343] __acpi_processor_start+0x48/0xb0
[ 21.028689] acpi_processor_start+0x40/0x60
[ 21.032860] really_probe+0x118/0x548
[ 21.036512] driver_probe_device+0x7c/0x148
[ 21.040684] device_driver_attach+0x94/0xa0
[ 21.044855] __driver_attach+0xa4/0x110
[ 21.048680] bus_for_each_dev+0xe8/0x158
[ 21.052591] driver_attach+0x30/0x40
[ 21.056155] bus_add_driver+0x234/0x2f0
[ 21.059980] driver_register+0xbc/0x1d0
[ 21.063805] acpi_processor_driver_init+0x40/0xe4
[ 21.068497] do_one_initcall+0xb4/0x254
[ 21.072322] kernel_init_freeable+0x24c/0x2f8
[ 21.076667] kernel_init+0x10/0x118
[ 21.080144] ret_from_fork+0x10/0x18
[ 21.083707]
[ 21.085186] Freed by task 1:
[ 21.088056] save_stack+0x28/0xc8
[ 21.091360] __kasan_slab_free+0x118/0x180
[ 21.095445] kasan_slab_free+0x10/0x18
[ 21.099183] kfree+0x80/0x268
[ 21.102139] acpi_cppc_processor_exit+0x1a8/0x1b8
[ 21.106832] acpi_processor_stop+0x70/0x80
[ 21.110917] really_probe+0x174/0x548
[ 21.114568] driver_probe_device+0x7c/0x148
[ 21.118740] device_driver_attach+0x94/0xa0
[ 21.122912] __driver_attach+0xa4/0x110
[ 21.126736] bus_for_each_dev+0xe8/0x158
[ 21.130648] driver_attach+0x30/0x40
[ 21.134212] bus_add_driver+0x234/0x2f0
[ 21.0x10/0x18
[ 21.161764]
[ 21.163244] The buggy address belongs to the object at ffff00236cdeb600
[ 21.163244] which belongs to the cache kmalloc-256 of size 256
[ 21.175750] The buggy address is located 132 bytes inside of
[ 21.175750] 256-byte region [ffff00236cdeb600, ffff00236cdeb700)
[ 21.187473] The buggy address belongs to the page:
[ 21.192254] page:fffffe008d937a00 refcount:1 mapcount:0 mapping:ffff002370c0fa00 index:0x0 compound_mapcount: 0
[ 21.202331] flags: 0x1ffff00000010200(slab|head)
[ 21.206940] raw: 1ffff00000010200 dead000000000100 dead000000000122 ffff002370c0fa00
[ 21.214671] raw: 0000000000000000 00000000802a002a 00000001ffffffff 0000000000000000
[ 21.222400] page dumped because: kasan: bad access detected
[ 21.227959]
[ 21.229438] Memory state around the buggy address:
[ 21.234218] ffff00236cdeb580: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 21.241427] ffff00236cdeb600: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.248637] >ffff00236cdeb680: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.255845] ^
[ 21.259062] ffff00236cdeb700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 21.266272] ffff00236cdeb780: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 21.273480] ==================================================================
It seems that global pcc_data[pcc_ss_id] can be freed in
acpi_cppc_processor_exit(), but we may later reference this value, so
NULLify it when freed.
Also remove the useless setting of data "pcc_channel_acquired", which
we're about to free.
Fixes: 85b1407bf6d2 ("ACPI / CPPC: Make CPPC ACPI driver aware of PCC subspace IDs")
Signed-off-by: John Garry <john.garry@huawei.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
* pm-cpufreq:
ACPI: processor: Avoid NULL pointer dereferences at init time
cpufreq: Avoid cpufreq_suspend() deadlock on system shutdown
* pm-sleep:
PM: sleep: include <linux/pm_runtime.h> for pm_wq
ACPI: PM: Drop Dell XPS13 9360 from LPS0 Idle _DSM blacklist
|
|
The KSZ8795 PHY ID is in fact used by KSZ8794/KSZ8795/KSZ8765 switches.
Update the PHY ID and name to reflect that, as this family of switches
is commonly refered to as KSZ87xx
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ8051 PHY and the KSZ8794/KSZ8795/KSZ8765 switch share exactly the
same PHY ID. Since KSZ8051 is higher in the ksphy_driver[] list of PHYs
in the micrel PHY driver, it is used even with the KSZ87xx switch. This
is wrong, since the KSZ8051 configures registers of the PHY which are
not present on the simplified KSZ87xx switch PHYs and misconfigures
other registers of the KSZ87xx switch PHYs.
Fortunatelly, it is possible to tell apart the KSZ8051 PHY from the
KSZ87xx switch by checking the Basic Status register Bit 0, which is
read-only and indicates presence of the Extended Capability Registers.
The KSZ8051 PHY has those registers while the KSZ87xx switch does not.
This patch implements simple check for the presence of this bit for
both the KSZ8051 PHY and KSZ87xx switch, to let both use the correct
PHY driver instance.
Fixes: 9d162ed69f51 ("net: phy: micrel: add support for KSZ8795")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"This is this weeks fixes for drm.
The dma-resv one is probably the more important one a fair few people
have reported it, besides that it's a couple of panfrost, a few i915
and a few amdgpu fixes.
One radeon patch to fix some ppc64 related issues caused an x86
regression so is getting reverted for now.
Summary:
dma-resv:
- shared fences for lima/panfrost
ttm:
- prefault regression fix
- lifetime fix
panfrost:
- stopped job timeout fix
- missing register values
amdgpu:
- smu7 powerplay fix
- bail earlier for cik/si detection
- navi SDMA fix
radeon:
- revert a ppc64 shutdown fix that broke x86
i915:
- VBT information handling fix
- Circular locking fix
- preemption vs resubmission virtual requests fix"
* tag 'drm-fixes-2019-10-18' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Fixup preempt-to-busy vs resubmission of a virtual request
drm/i915/userptr: Never allow userptr into the mappable GGTT
drm/i915: Favor last VBT child device with conflicting AUX ch/DDC pin
drm/i915/execlists: Refactor -EIO markup of hung requests
drm/panfrost: Handle resetting on timeout better
drm/panfrost: Add missing GPU feature registers
drm/ttm: fix handling in ttm_bo_add_mem_to_lru
drm/ttm: Restore ttm prefaulting
drm/ttm: fix busy reference in ttm_mem_evict_first
drm/amdgpu/sdma5: fix mask value of POLL_REGMEM packet for pipe sync
drm/amdgpu: Bail earlier when amdgpu.cik_/si_support is not set to 1
Revert "drm/radeon: Fix EEH during kexec"
drm/msm/dsi: Implement reset correctly
dma-buf/resv: fix exclusive fence get
drm/edid: Add 6 bpc quirk for SDC panel in Lenovo G50
drm/tiny: Kconfig: Remove always-y THERMAL dep. from TINYDRM_REPAPER
drm/amdgpu/powerplay: fix typo in mvdd table setup
|
|
-dma-resv: Change shared_count to post-increment to fix lima crash (Qiang)
-ttm: A couple fixes related to lifetime and restore prefault behavior
(Christian & Thomas)
-panfrost: Fill in missing feature reg values and fix stoppedjob timeouts
(Steven)
Cc: Qiang Yu <yuq825@gmail.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Christian König <christian.koenig@amd.com>
Cc: Steven Price <steven.price@arm.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20191017203419.GA142909@art_vandelay
|
|
drm-fixes-5.4-2019-10-16:
amdgpu:
- Powerplay fix for SMU7 parts
- Bail earlier when cik/si support is not set to 1
- Fix an SDMA issue on navi
radeon:
- revert a PPC fix which broken x86
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191017022443.3853-1-alexander.deucher@amd.com
|
|
The KSZ driver uses one regmap per register width (8/16/32), each with
it's own lock, but accessing the same set of registers. In theory, it
is possible to create a race condition between these regmaps, although
the underlying bus (SPI or I2C) locking should assure nothing bad will
really happen and the accesses would be correct.
To make the driver do the right thing, add one single shared mutex for
all the regmaps used by the driver instead. This assures that even if
some future hardware is on a bus which does not serialize the accesses
the same way SPI or I2C does, nothing bad will happen.
Note that the status_mutex was unused and only initied, hence it was
renamed and repurposed as the regmap mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The KSZ87xx driver calls mutex_init() on mutexes already inited in
ksz_common.c ksz_switch_register(). Do not do it twice, drop the
reinitialization.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: David S. Miller <davem@davemloft.net>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: George McCollister <george.mccollister@gmail.com>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Cc: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The stmmac_pcs_ctrl_ane() expects a register address as
argument 1, but for some reason the mac_device_info is
being passed.
Fix the warning (and possible bug) from sparse:
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: warning: incorrect type in argument 1 (different address spaces)
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: expected void [noderef] <asn:2> *ioaddr
drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:2613:17: got struct mac_device_info *hw
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on when MC connects the DPNI to a MAC, Tx FQIDs may
not be available during probe time.
Read the FQIDs each time the link goes up to avoid using invalid
values. In case an error occurs or an invalid value is retrieved,
fall back to QDID-based enqueueing.
Fixes: 1fa0f68c9255 ("dpaa2-eth: Use FQ-based DPIO enqueue API")
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add IRQ for the DPNI endpoint change event, resolving the issue
when a dynamically created DPNI gets a randomly generated hw address
when the endpoint is a DPMAC object.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Codrin Ciubotariu
Linus Walleij
Geert Uytterhoeven
YueHaibing
Linus Torvalds
Mans Rullgard
Chenwandun
Michael Tretter
Juergen Gross
Yonglong Liu
David Hildenbrand
Andrew Lunn
Ido Schimmel
Doug Berger
Joerg Roedel
Jens Axboe
Kevin Hao
Rafael J. Wysocki
John Garry
Marek Vasut
Dave Airlie
Ben Dooks (Codethink)
Ioana Radulescu
Florin Chiculita