aboutsummaryrefslogtreecommitdiffstats
path: root/drivers (follow)
AgeCommit message (Collapse)AuthorFilesLines
2016-05-17drivers: net: Don't print unpopulated net_device nameHarvey Hunt3-10/+20
For ethernet devices, net_device.name will be eth%d before register_netdev() is called. Don't print the net_device name until the format string is replaced. Signed-off-by: Harvey Hunt <harvey.hunt@imgtec.com> Cc: Marcel Ziswiler <marcel@ziswiler.com> Cc: Robert Jarzmik <robert.jarzmik@free.fr> Cc: Barry Song <Baohua.Song@csr.com> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17qed: add support for dcbx.Sudarsana Reddy Kalluru10-8/+825
This patch adds the necessary driver support for Management Firmware to configure the device/firmware with the dcbx results. Management Firmware is responsible for communicating the DCBX and driving the negotiation, but the driver has responsibility of receiving async notification and configuring the results in hw/fw. This patch also adds the dcbx support for future protocols (e.g., FCoE) as preparation to their imminent submission. Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17ravb: Add missing free_irq() calls to ravb_close()Geert Uytterhoeven1-1/+6
When reopening the network device on ra7795/salvator-x, e.g. after a DHCP timeout: IP-Config: Reopening network devices... genirq: Flags mismatch irq 139. 00000000 (eth0:ch0:rx_be) vs. 00000000 (ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch0:rx_be IP-Config: Failed to open eth0 IP-Config: No network devices available The "mismatch" is due to requesting an IRQ that is already in use, while IRQF_PROBE_SHARED wasn't set. However, the real cause is that ravb_close() doesn't release any of the R-Car Gen3-specific secondary IRQs. Add the missing free_irq() calls to fix this. Fixes: f51bdc236b6c5835 ("ravb: Add dma queue interrupt support") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17qed: Remove a stray tabDan Carpenter1-1/+1
This line was indented more than it should be. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-17Merge branch '10GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queueDavid S. Miller1-6/+6
Jeff Kirsher says: ==================== 10GbE Intel Wired LAN Driver Updates 2016-05-16 This series contains 2 fixes to ixgbe only. Emil fixes transmit hangs when enabling SRIOV by swapping the parameters in GENMASK in order to generate the correct mask. Alex fixes his previous patch b83e30104bd9 ("ixgbe/ixgbevf: Add support for GSO partial") where he somehow transposed the location of setting the VLAN features in netdev->features and the configuration of the vlan_features. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fec-mpc52xx: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-24/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fec-mpc52xx: use phydev from struct net_devicePhilippe Reynes1-23/+20
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is setEzequiel Garcia1-1/+6
Commit f748be531d70 ("stmmac: support new GMAC4") reverted a previous fix by mistake. This commit re-applies said fix: commit dec2165ff38a99f937fe61875d102c6c8596c815 Author: Sonic Zhang <sonic.zhang@analog.com> Date: Thu Jan 22 14:55:57 2015 +0800 stmmac: hardware TX COE doesn't work when force_thresh_dma_mode is set Clear the TX COE bit when force_thresh_dma_mode is set even hardware dma capability says support. Tested on BF609. Signed-off-by: Sonic Zhang <sonic.zhang@analog.com> Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by: David S. Miller <davem@davemloft.net> Tested on LPC4350 Hitex board. Fixes: f748be531d70 ("stmmac: support new GMAC4") Signed-off-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar> Tested-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fs-enet: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-24/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: fs-enet: use phydev from struct net_devicePhilippe Reynes5-26/+18
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: ftgmac100: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-14/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: ftgmac100: use phydev from struct net_devicePhilippe Reynes1-16/+8
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: gianfar: use phy_ethtool_{get|set}_link_ksettingsPhilippe Reynes1-25/+2
There are two generics functions phy_ethtool_{get|set}_link_ksettings, so we can use them instead of defining the same code in the driver. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: ethernet: gianfar: use phydev from struct net_devicePhilippe Reynes3-32/+35
The private structure contain a pointer to phydev, but the structure net_device already contain such pointer. So we can remove the pointer phydev in the private structure, and update the driver to use the one contained in struct net_device. Signed-off-by: Philippe Reynes <tremyfr@gmail.com> Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16ixgbe: Fix VLAN features errorAlexander Duyck1-4/+4
It looks like at some point I somehow transposed the location of setting the VLAN features in netdev->features and the configuration of the vlan_features. As a result the driver is now generating a warning about vlan_features being setup incorrectly. This patch corrects that by placing the update of netdev->features to include the VLAN features so that it is after the point where we write netdev->features into netdev->vlan_features. Fixes: b83e30104bd9 ("ixgbe/ixgbevf: Add support for GSO partial") Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-16ixgbe: use correct mask when enabling sriovEmil Tantilov1-2/+2
Swap the parameters in GENMASK in order to generate the correct mask. This change fixes Tx hangs when enabling SRIOV. Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-05-16qed: VFs gracefully accept lack of PMYuval Mintz1-1/+1
VF's probe might log that it has no PM capability in its PCI configuration space. As this is a valid configuration, silence such prints. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Allow more than 16 VFsYuval Mintz1-0/+3
In multi-function modes, PFs are currently limited to using 16 VFs - But that limitation would also currently apply in case there's a single PCI function exposed, where no such restriction should have existed. This lifts the restriction for the default mode; User should be able to start the maximum number of VFs as appear in the PCI config space. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Reset link on IOV disableManish Chopra1-39/+51
PF updates its VFs' bulletin boards with link configurations whenever the physical carrier changes or whenever hyper-user explicitly requires some setting of the VFs link via the hypervisor's PF. Since the bulletin board is getting cleaned as part of the IOV disable flow on the PF side, re-enabling sriov would lead to a VF that sees the carrier as 'down', until an event causing the PF to re-fill the bulletin with the link configuration would occur. To fix this we simply refelect the link state during the flows, giving the later VFs a default reflecting the PFs link state. Signed-off-by: Manish Chopra <Manish.Chopra@qlogic.com> Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Improve VF interrupt resetYuval Mintz4-60/+41
During FLR flow, need to make sure HW is no longer capable of writing to host memory as part of its interrupt mechanisms. While we're at it, unify the logic cleaning the driver's status-blocks into using a single API function for both PFs and VFs. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16qed: Correct PF-sanity checkYuval Mintz1-3/+3
Seems like something broke in commit 1408cc1fa48c ("qed: Introduce VFs") and the function no longer verifies that the vf is indeed a valid one. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/mlx4_core: Fix access to uninitialized indexTariq Toukan1-2/+2
Prevent using uninitialized or negative index when handling steering entries. Fixes: b12d93d63c32 ('mlx4: Add support for promiscuous mode in the new steering model.') Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16Merge branch 'for-upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/bluetooth/bluetooth-nextDavid S. Miller2-0/+3
Johan Hedberg says: ==================== pull request: bluetooth-next 2016-05-14 Here are two more Bluetooth patches for the 4.7 kernel which we wanted to get into net-next before the merge window opens. Please let me know if there are any issues pulling. Thanks. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100-spi: add support to specify MAC address by device treeAkinobu Mita3-4/+8
This adds support to specify the MAC address by 'mac-address' or 'local-mac-address' properties in the device tree. These are common properties for the Ethernet controller. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100: increase TX timeout periodAkinobu Mita1-1/+0
This increases TX timeout period from one second to 5 seconds which is the default value if the driver doesn't explicitly set net_device->watchdog_timeo. The one second timeout is too short for W5100 with SPI interface mode which doesn't support burst READ/WRITE processing in the SPI transfer. If the packet is transmitted while RX packets are being received at a very high rate, the TX transmittion work in the workqueue is delayed and the watchdog timer is expired. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100: fix MAC filtering for W5500Akinobu Mita1-4/+13
W5500 has different bit position for MAC filter in Socket n mode register from W5100 and W5200. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: w5100: remove unused is_w5200()Akinobu Mita1-5/+0
The is_w5200() function is not used anymore by the commit which adds the W5500 support. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Cc: Mike Sinkovsky <msink@permonline.ru> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16lxt: simplify lxt970_config_init()Sergei Shtylyov1-5/+1
This function declares the 'err' local variable for no good reason, get rid of it. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16lxt: simplify lxt97[01]_config_intr()Sergei Shtylyov1-12/+4
Both these functions declare the 'err' local variables for no good reason, get rid of them. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: dsa: mv88e6xxx: remove bridge workVivien Didelot2-34/+8
Now that the bridge code defers the switchdev port state setting, there is no need to defer the port STP state change within the mv88e6xxx code. Thus get rid of the driver's bridge work code. This also fixes a race condition where the DSA layer assumes that the bridge code already set the unbridged port's STP state to Disabled before restoring the Forwarding state. As a consequence, this also fixes the FDB flush for the unbridged port which now correctly occurs during the Forwarding to Disabled transition. Fixes: 0bc05d585d38 ("switchdev: allow caller to explicitly request attr_set as deferred") Reported-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: vrf: protect changes to private data with rcuDavid Ahern1-23/+47
One cpu can be processing packets which includes using the cached route entries in the vrf device's private data and on another cpu the device gets deleted which releases the routes and sets the pointers in net_vrf to NULL. This results in datapath dereferencing a NULL pointer. Fix by protecting access to dst's with rcu. Fixes: 193125dbd8eb ("net: Introduce VRF device driver") Fixes: 35402e313663 ("net: Add IPv6 support to VRF device") Signed-off-by: David Ahern <dsa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/mlx5e: Hardware offloaded flower filter statistics supportAmir Vadai3-7/+69
Introduce support in updating statistics of offloaded TC flower classifiers. Currently only the DROP action is supported. Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/mlx5_core: Flow counters infrastructureAmir Vadai4-2/+236
If a counter has the aging flag set when created, it is added to a list of counters that will be queried periodically from a workqueue. query result and last use timestamp are cached. add/del counter must be very efficient since thousands of such operations might be issued in a second. There is only a single reference to counters without aging, therefore no need for locks. But, counters with aging enabled are stored in a list. In order to make code as lockless as possible, all the list manipulation and access to hardware is done from a single context - the periodic counters query thread. The hardware supports multiple counters per FTE, however currently we are using one counter for each FTE. Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/mlx5_core: Introduce flow steering destination of type counterAmir Vadai4-10/+102
When adding a flow steering rule with a counter, need to supply a destination of type MLX5_FLOW_DESTINATION_TYPE_COUNTER, with a pointer to a struct mlx5_fc. Also, MLX5_FLOW_CONTEXT_ACTION_COUNT bit should be set in the action. Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/mlx5_core: Firmware commands to support flow countersAmir Vadai3-0/+77
Getting packet/byte statistics on flows is done through flow counters. Implement the firmware commands to alloc, free and query flow counters. Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net/mlx5_core: Use a macro in mlx5_command_str()Amir Vadai1-171/+132
Use a macro instead of copying the OP name. Signed-off-by: Amir Vadai <amirva@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: pxa168_eth: Use dma_wmb/rmb where appropriateJisheng Zhang1-4/+4
Update the pxa168_eth driver to use the dma_rmb/wmb calls instead of the full barriers in order to improve performance: reduced 97ns/39ns on average in tx/rx path on Marvell BG4CT platform. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16net: pxa168_eth: use {readl|writel}_relaxed instead of readl/writelJisheng Zhang1-2/+2
Since appropriate memory barriers are already there, use the relaxed version to improve performance a bit. Signed-off-by: Jisheng Zhang <jszhang@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16vxlan: set mac_header correctly in GPE modeJiri Benc1-0/+1
For VXLAN-GPE, the interface is ARPHRD_NONE, thus we need to reset mac_header after pulling the outer header. v2: Put the code to the existing conditional block as suggested by Shmulik Ladkani. Fixes: e1e5314de08b ("vxlan: implement GPE") Signed-off-by: Jiri Benc <jbenc@redhat.com> Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16xen-netback: use hash value from the frontendPaul Durrant1-0/+27
My recent patch to include/xen/interface/io/netif.h defines a new extra info type that can be used to pass hash values between backend and guest frontend. This patch adds code to xen-netback to use the value in a hash extra info fragment passed from the guest frontend in a transmit-side (i.e. netback receive side) packet to set the skb hash accordingly. Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16xen-netback: pass hash value to the frontendPaul Durrant2-14/+77
My recent patch to include/xen/interface/io/netif.h defines a new extra info type that can be used to pass hash values between backend and guest frontend. This patch adds code to xen-netback to pass hash values calculated for guest receive-side packets (i.e. netback transmit side) to the frontend. Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16xen-netback: add control protocol implementationPaul Durrant5-3/+502
My recent patch to include/xen/interface/io/netif.h defines a new shared ring (in addition to the rx and tx rings) for passing control messages from a VM frontend driver to a backend driver. A previous patch added the necessary boilerplate for mapping the control ring from the frontend, should it be created. This patch adds implementations for each of the defined protocol messages. Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Cc: Wei Liu <wei.liu2@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16xen-netback: add control ring boilerplatePaul Durrant4-30/+277
My recent patch to include/xen/interface/io/netif.h defines a new shared ring (in addition to the rx and tx rings) for passing control messages from a VM frontend driver to a backend driver. This patch adds the necessary code to xen-netback to map this new shared ring, should it be created by a frontend, but does not add implementations for any of the defined protocol messages. These are added in a subsequent patch for clarity. Signed-off-by: Paul Durrant <paul.durrant@citrix.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16hv_netvsc: set nvdev link after populating chn_tableVitaly Kuznetsov1-11/+18
Crash in netvsc_send() is observed when netvsc device is re-created on mtu change/set channels. The crash is caused by dereferencing of NULL channel pointer which comes from chn_table. The root cause is a mixture of two facts: - we set nvdev pointer in net_device_context in alloc_net_device() before we populate chn_table. - we populate chn_table[0] only. The issue could be papered over by checking channel != NULL in netvsc_send() but populating the whole chn_table and writing the nvdev pointer afterwards seems more appropriate. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16hv_netvsc: synchronize netvsc_change_mtu()/netvsc_set_channels() with netvsc_remove()Vitaly Kuznetsov1-2/+7
When netvsc device is removed during mtu change or channels setup we get into troubles as both paths are trying to remove the device. Synchronize them with start_remove flag and rtnl lock. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16hv_netvsc: get rid of struct net_device pointer in struct netvsc_deviceVitaly Kuznetsov4-64/+72
Simplify netvsvc pointer graph by getting rid of the redundant ndev pointer. We can always get a pointer to struct net_device from somewhere else. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16hv_netvsc: untangle the pointer messVitaly Kuznetsov4-122/+99
We have the following structures keeping netvsc adapter state: - struct net_device - struct net_device_context - struct netvsc_device - struct rndis_device - struct hv_device and there are pointers/dependencies between them: - struct net_device_context is contained in struct net_device - struct hv_device has driver_data pointer which points to 'struct net_device' OR 'struct netvsc_device' depending on driver's state (!). - struct net_device_context has a pointer to 'struct hv_device'. - struct netvsc_device has pointers to 'struct hv_device' and 'struct net_device_context'. - struct rndis_device has a pointer to 'struct netvsc_device'. Different functions get different structures as parameters and use these pointers for traveling. The problem is (in addition to keeping in mind this complex graph) that some of these structures (struct netvsc_device and struct rndis_device) are being removed and re-created on mtu change (as we implement it as re-creation of hyper-v device) so our travel using these pointers is dangerous. Simplify this to a the following: - add struct netvsc_device pointer to struct net_device_context (which is a part of struct net_device and thus never disappears) - remove struct hv_device and struct net_device_context pointers from struct netvsc_device - replace pointer to 'struct netvsc_device' with pointer to 'struct net_device'. - always keep 'struct net_device' in hv_device driver_data. We'll end up with the following 'circular' structure: net_device: [net_device_context] -> netvsc_device -> rndis_device -> net_device -> hv_device -> net_device On MTU change we'll be removing the 'netvsc_device -> rndis_device' branch and re-creating it making the synchronization easier. There is one additional redundant pointer left, it is struct net_device link in struct netvsc_device, it is going to be removed in a separate commit. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16hv_netvsc: use start_remove flag to protect netvsc_link_change()Vitaly Kuznetsov1-4/+17
netvsc_link_change() can race with netvsc_change_mtu() or netvsc_set_channels() as these functions destroy struct netvsc_device and rndis filter. Use start_remove flag for syncronization. As netvsc_change_mtu()/netvsc_set_channels() are called with rtnl lock held we need to take it before checking start_remove value in netvsc_link_change(). Reported-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16hv_netvsc: move start_remove flag to net_device_contextVitaly Kuznetsov3-6/+13
struct netvsc_device is destroyed on mtu change so keeping the protection flag there is not a good idea. Move it to struct net_device_context which is preserved. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-05-16phy: add support for a reset-gpio specificationUwe Kleine-König1-0/+8
The framework only asserts (for now) that the reset gpio is not active. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Reviewed-by: Roger Quadros <rogerq@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.