| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use correct define ALE_SUPER for ALE Multicast Address Table Entry
Supervisory Packet (SUPER) bit setting instead of ALE_BLOCKED. No issues
were observed till now as it have never been set, but it's going to be used
by new CPSW switch driver.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop unnecessary wrapper function cpsw_tx_packet_submit() which is used
only in one place.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_alloc_etherdev_mqs() and simplify code.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drop pinctrl_pm_select_default_state call from probe as default
pinctrl state is set by DD core.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use local variable struct device *dev in probe to simplify code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update cpsw_split_res() to accept struct cpsw_common instead of
struct net_device to simplify code.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All TI drivers CPSW/NETCP can't work without ALE, hence simplify
build of those drivers by always linking cpsw_ale and drop
CONFIG_TI_CPSW_ALE config option.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both drivers CPSW and EMAC can't work without CPDMA, hence simplify build
of those drivers by always linking davinci_cpdma and drop TI_DAVINCI_CPDMA
config option.
Note. the davinci_emac driver module was changed to "ti_davinci_emac" to
make build work.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace textual license with SPDX-License-Identifier.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add options to strictly validate messages and dump messages,
sometimes perhaps validating dump messages non-strictly may
be required, so add an option for that as well.
Since none of this can really be applied to existing commands,
set the options everwhere using the following spatch:
@@
identifier ops;
expression X;
@@
struct genl_ops ops[] = {
...,
{
.cmd = X,
+ .validate = GENL_DONT_VALIDATE_STRICT | GENL_DONT_VALIDATE_DUMP,
...
},
...
};
For new commands one should just not copy the .validate 'opt-out'
flags and thus get strict validation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even if the NLA_F_NESTED flag was introduced more than 11 years ago, most
netlink based interfaces (including recently added ones) are still not
setting it in kernel generated messages. Without the flag, message parsers
not aware of attribute semantics (e.g. wireshark dissector or libmnl's
mnl_nlmsg_fprintf()) cannot recognize nested attributes and won't display
the structure of their contents.
Unfortunately we cannot just add the flag everywhere as there may be
userspace applications which check nlattr::nla_type directly rather than
through a helper masking out the flags. Therefore the patch renames
nla_nest_start() to nla_nest_start_noflag() and introduces nla_nest_start()
as a wrapper adding NLA_F_NESTED. The calls which add NLA_F_NESTED manually
are rewritten to use nla_nest_start().
Except for changes in include/net/netlink.h, the patch was generated using
this semantic patch:
@@ expression E1, E2; @@
-nla_nest_start(E1, E2)
+nla_nest_start_noflag(E1, E2)
@@ expression E1, E2; @@
-nla_nest_start_noflag(E1, E2 | NLA_F_NESTED)
+nla_nest_start(E1, E2)
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds four tracepoints to nbd, enabling separate tracing of payload
and header sending/receipt.
In the send path for headers that have already been sent, we also
explicitly initialize the handle so it can be referenced by the later
tracepoint.
Signed-off-by: Andrew Hall <hall@fb.com>
Signed-off-by: Matt Mullins <mmullins@fb.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
This adds a tracepoint that can both observe the nbd request being sent
to the server, as well as modify that request , e.g., setting a flag in
the request that will cause the server to collect detailed tracing data.
The struct request * being handled is included to permit correlation
with the block tracepoints.
Signed-off-by: Matt Mullins <mmullins@fb.com>
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Johannes Berg says:
====================
Various updates, notably:
* extended key ID support (from 802.11-2016)
* per-STA TX power control support
* mac80211 TX performance improvements
* HE (802.11ax) updates
* mesh link probing support
* enhancements of multi-BSSID support (also related to HE)
* OWE userspace processing support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's meaningless to trigger reset when failed to send command to IMP,
because the failure is usually caused by no authority, illegal command
and so on. When that happened, we just need to return the status code
for further debugging.
Signed-off-by: Weihang Li <liweihang@hisilicon.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a check for the hns3_put_ring_config() to prevent
double free, and for more readable, move the NULL assignment of
priv->ring_data into the hns3_put_ring_config().
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The test results show that the maximum time of hardware return
to mac link state is 500MS.The software needs to set twice the
maximum time of hardware return state (1000MS).
If not modified, the loopback test returns probability failure.
Signed-off-by: liuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configure pause, current implementation returns directly
after setup PFC without setup BP, which is not sufficient.
So this patch fixes it, only return while setting PFC failed.
Fixes: 44e59e375bf7 ("net: hns3: do not return GE PFC setting err when initializing")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the hardware does not handle mailboxes and the hardware
reset include TQP reset, so it is unnecessary to reset TQP
in the hclgevf_ae_stop() while doing VF reset. Also it is
unnecessary to reset the remaining TQP when one reset fails.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch uses a reserved byte in the hclge_mbx_vf_to_pf_cmd
to save the need_resp flag, so when PF received the mailbox,
it can use it to decise whether send a response to VF.
For hclge_set_vf_uc_mac_addr(), it should use mbx_need_resp flag
to decide whether send response to VF.
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since irq handler and mailbox task will both update arq's count,
so arq's count should use atomic_t instead of u32, otherwise
its value may go wrong finally.
Fixes: 07a0556a3a73 ("net: hns3: Changes to support ARQ(Asynchronous Receive Queue)")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCLGEVF_STATE_CMD_DISABLE is more suitable than
HCLGEVF_STATE_RST_HANDLING to stop sending keep alive msg,
since HCLGEVF_STATE_RST_HANDLING only be set when the reset
task is running.
Fixes: c59a85c07e77 ("net: hns3: stop sending keep alive msg to PF when VF is resetting")
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bdinfo handled in hns3_handle_bdinfo is only valid on the
last BD of the current packet, currently the bd info may be handled
based on the first BD if the packet has more than two BDs, which
may cause rx error.
This patch fixes it by using the last BD of the current packet in
hns3_handle_bdinfo.
Also, hns3_set_rx_skb_rss_type has used RSS hash value from the last
BD of the current packet, so remove the same last BD calculation in
hns3_set_rx_skb_rss_type and call it from hns3_handle_bdinfo.
Fixes: e55970950556 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hns3_desc_unused() returns how many BD have been cleaned, but new
buffer has not been attached to them. The register of
HNS3_RING_RX_RING_FBDNUM_REG returns how many BD need allocating new
buffer to or need to cleaned. So the remaining BD need to be clean
is HNS3_RING_RX_RING_FBDNUM_REG - hns3_desc_unused().
Also, new buffer can not attach to the pending BD when the last BD is
not handled, because memcpy has not been done on the first pending BD.
This patch fixes by subtracting the pending BD num from unused_count
after 'HNS3_RING_RX_RING_FBDNUM_REG - unused_count' is used to calculate
the BD bum need to be clean.
Fixes: e55970950556 ("net: hns3: Add handling of GRO Pkts not fully RX'ed in NAPI poll")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
hns3_clean_tx_ring calls hns3_nic_reclaim_one_desc to clean
buffers and set ring->next_to_clean, then hns3_nic_net_xmit
reuses the cleaned buffers. But there are no memory barriers
when buffers gets recycled, so the recycled buffers can be
corrupted.
This patch uses smp_store_release to update ring->next_to_clean
and smp_load_acquire to read ring->next_to_clean to properly
hand off buffers from hns3_clean_tx_ring to hns3_nic_net_xmit.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Device may be shutdown without the hardware being reinitialized, in
which case we want to ensure we cleanup properly.
This is especially important for kexec with traffic flowing.
The shutdown procedures resembles the remove procedures, so we can reuse
those common tasks.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/nfc/st95hf/core.c: In function 'st95hf_irq_thread_handler':
drivers/nfc/st95hf/core.c:786:26: warning:
variable 'nfcddev' set but not used [-Wunused-but-set-variable]
drivers/nfc/st95hf/core.c:784:17: warning:
variable 'dev' set but not used [-Wunused-but-set-variable]
They are never used since introduction in
commit cab47333f0f7 ("NFC: Add STMicroelectronics ST95HF driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY's behave differently when being reset. Some reset registers to
defaults, some don't. Some trigger an autoneg restart, some don't.
So let's also set the autoneg restart bit when resetting. Then PHY
behavior should be more consistent. Clearing BMCR_ISOLATE serves the
same purpose and is borrowed from genphy_restart_aneg.
BMCR holds the speed / duplex settings in fixed mode. Therefore
we may have an issue if a soft reset resets BMCR to its default.
So better call genphy_setup_forced() afterwards in fixed mode.
We've seen no related complaint in the last >10 yrs, so let's
treat it as an improvement.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All Apple products use the same protocol for tethering over USB.
To simplify the code and make it future proof, use
USB_VENDOR_AND_INTERFACE_INFO() instead of
USB_DEVICE_AND_INTERFACE_INFO() to automatically detect and support
all existing and future Apple products using the same interface.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, refactor code a
bit and mark switch cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/broadcom/cnic.c: In function ‘cnic_cm_process_kcqe’:
drivers/net/ethernet/broadcom/cnic.c:4044:11: warning: this statement may fall through [-Wimplicit-fallthrough=]
opcode = L4_KCQE_OPCODE_VALUE_CLOSE_COMP;
drivers/net/ethernet/broadcom/cnic.c:4050:2: note: here
case L4_KCQE_OPCODE_VALUE_RESET_RECEIVED:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c: In function ‘fwevtq_handler’:
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:520:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
cpl = (void *)p;
~~~~^~~~~~~~~~~
drivers/net/ethernet/chelsio/cxgb4vf/cxgb4vf_main.c:524:2: note: here
case CPL_SGE_EGR_UPDATE: {
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
In file included from drivers/net/wimax/i2400m/debug-levels.h:30,
from drivers/net/wimax/i2400m/control.c:86:
drivers/net/wimax/i2400m/control.c: In function ‘i2400m_report_tlv_system_state’:
./include/linux/wimax/debug.h:200:4: warning: this statement may fall through [-Wimplicit-fallthrough=]
do { \
^
./include/linux/wimax/debug.h:404:36: note: in expansion of macro ‘_d_printf’
#define d_printf(l, _dev, f, a...) _d_printf(l, "", _dev, f, ## a)
^~~~~~~~~
drivers/net/wimax/i2400m/control.c:354:3: note: in expansion of macro ‘d_printf’
d_printf(1, dev, "entering BS-negotiated idle mode\n");
^~~~~~~~
drivers/net/wimax/i2400m/control.c:355:2: note: here
case I2400M_SS_DISCONNECTING:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warnings:
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-drv.c: In function ‘xgbe_set_hwtstamp_settings’:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1614:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1616:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_EVENT:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1625:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1627:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_SYNC:
^~~~
In file included from drivers/net/ethernet/amd/xgbe/xgbe-drv.c:129:
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1392:9: warning: this statement may fall through [-Wimplicit-fallthrough=]
(_var) |= (((_val) & ((0x1 << (_width)) - 1)) << (_index)); \
~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-common.h:1419:2: note: in expansion of macro ‘SET_BITS’
SET_BITS((_var), \
^~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1636:3: note: in expansion of macro ‘XGMAC_SET_BITS’
XGMAC_SET_BITS(mac_tscr, MAC_TSCR, TSVER2ENA, 1);
^~~~~~~~~~~~~~
drivers/net/ethernet/amd/xgbe/xgbe-drv.c:1638:2: note: here
case HWTSTAMP_FILTER_PTP_V1_L4_DELAY_REQ:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comments are modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When building the L3 HW header for non-IP packets, trust the cast type
that was passed as parameter. qeth_l3_get_cast_type() has most likely
also used h_dest to determine the cast type, so we get the same
result, and can remove that duplicated code.
In the unlikely case that we would get a _different_ cast type, then
that's based off a route lookup and should be considered authoritative.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This de-duplicates the L2 and L3 cast-type code, and makes the L2 code
a bit more robust by removing the fragile assumption that skb->data
always points to the Ethernet Header. This would break in code paths
where we pushed the HW header onto the skb.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The QETH_MAX_BUFFER_ELEMENTS() macro effectively returns a constant
value. To avoid some redundant pointer chasing and computations in the
xmit hot path, cache this value in the queue struct.
Take this as opportunity to shrink some of the queue struct's fields to
their appropriate value range, slightly reducing its total size.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the first initialization of a queue, its Output Buffers are in a
clean state with no attached resources. On every subsequent
initialization, qeth_l?_stop_card() has previously put them in a clean
state via qeth_drain_output_queues(). So the call to
qeth_clear_output_buffer() is redundant and can be removed.
While at it, move the initialization of the queue's card pointer into
the queue allocation. It never changes afterwards.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We have helper macros for all possible device types, replace all
remaining open-coded accesses to the type fields.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't keep track of Input Buffer states, so remove the comments that
make it sound like the qeth_qdio_buffer_states enum applies to
Input Buffers.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's unclear what exact purpose this seqno may have served in the past.
But it's certainly no longer used anymore, as the following
napi_gro_receive() will straight away clear this part of the cb again.
Suggested-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clang produces a harmless warning for each use for the qeth_adp_supported
macro:
drivers/s390/net/qeth_l2_main.c:559:31: warning: implicit conversion from enumeration type 'enum qeth_ipa_setadp_cmd' to
different enumeration type 'enum qeth_ipa_funcs' [-Wenum-conversion]
if (qeth_adp_supported(card, IPA_SETADP_SET_PROMISC_MODE))
~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/s390/net/qeth_core.h:179:41: note: expanded from macro 'qeth_adp_supported'
qeth_is_ipa_supported(&c->options.adp, f)
~~~~~~~~~~~~~~~~~~~~~ ^
Add a version of this macro that uses the correct types, and
remove the unused qeth_adp_enabled() macro that has the same
problem.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow Extended Key ID to be used with hwsim.
Hwsim can only communicate with other hwsim cards, allowing it to bypass
creation of A-MPDUs in the first place.
Mixing keyIDs in an A-MPDU is therefore impossible and can never cause
interoperability issues with other cards.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[reword comment slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
P2P device interface type was not indicated in the supported
interface types even when hwsim was configured with p2p device
support. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Implement ndo_get_devlink_port and allow switch_id and port_name to be
handled by devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the existing way to create netdevsim over rtnetlink and move the
netdev creation/destruction to dev probe, so for every probed port,
a netdevsim-netdev instance is created.
Adjust selftests to work with new interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to test flows in core, it is beneficial to maintain previously
supported possibility to add and delete ports during netdevsim lifetime.
Do it by extending device sysfs attrs by "new_port" and "del_port".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement netdevsim bus probing of netdevsim devices. For every probed
device create a devlink instance. According to the user-passed value,
create a number of ports represented by devlink port instances.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the model where dev is represented by devlink and ports are
represented by devlink ports, make debugfs file names independent
on netdev names. Change the topology to the one illustrated
by the following example:
$ ls /sys/kernel/debug/netdevsim/
netdevsim1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/
bpf_bind_accept bpf_bind_verifier_delay bpf_bound_progs ports
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/
0 1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/
bpf_map_accept bpf_offloaded_id bpf_tc_accept bpf_tc_non_bound_accept bpf_xdpdrv_accept bpf_xdpoffload_accept dev ipsec
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -l
lrwxrwxrwx 1 root root 0 Apr 13 15:58 /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -> ../../../netdevsim1
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation of parent_id/switch_id does not follow the
original idea of being unique. The values are "0", "1", etc. Instead of
that, generate 32 random bytes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Grygorii Strashko
Johannes Berg
Michal Kubecek
Andrew Hall
Matt Mullins
David S. Miller
Weihang Li
Huazhong Tan
liuzhongzhu
Yunsheng Lin
Dirk van der Merwe
YueHaibing
Heiner Kallweit
Guenter Roeck
Gustavo A. R. Silva
Julian Wiedmann
Arnd Bergmann
Alexander Wetzel
Avraham Stern
Jiri Pirko