| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Kalle Valo says:
====================
wireless-drivers-next patches for v5.5
Last set of patches for v5.5. Major features here 802.11ax support for
qtnfmac and airtime fairness support to mt76. And naturally smaller
fixes and improvements all over.
Major changes:
qtnfmac
* add 802.11ax support in AP mode
* enable offload bridging support
iwlwifi
* support TX/RX antennas reporting
mt76
* mt7615 smart carrier sense support
* aggregation statistics via debugfs
* airtime fairness (ATF) support
* mt76x0 OF mac address support
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
When a phydev is created, the speed and duplex are set to zero and
-1 respectively, rather than using the predefined SPEED_UNKNOWN and
DUPLEX_UNKNOWN constants.
There is a window at initialisation time where we may report link
down using the 0/-1 values. Tidy this up and use the predefined
constants, so debug doesn't complain with:
"Unsupported (update phy-core.c)/Unsupported (update phy-core.c)"
when the speed and duplex settings are printed.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
There are no users of phy_ethtool_sset() in the kernel anymore, and
as of commit 3c1bcc8614db ("net: ethernet: Convert phydev advertize
and supported from u32 to link mode"), the implementation is slightly
buggy - it doesn't correctly check the masked advertising mask as it
used to.
Remove it, and update the phy documentation to refer to its replacement
function.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
If there's no traffic on a channel, its ARFS expiry work will never get
scheduled by efx_poll() as that isn't being run.
So make efx_filter_rfs_expire() reschedule itself to run after 30 seconds.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Report the number of successful and failed insertions, and also the
current count of filters, to aid in tuning e.g. rps_flow_cnt.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
In high connection count usage, the NIC's filter table may be filled with
sufficiently many ARFS filters that further insertions fail. As this
does not represent a correctness issue, do not log the resulting MCDI
errors. Add a debug-level message under the (by default disabled)
rx_status category instead; and take the opportunity to do a little extra
expiry work.
Since there are now multiple workitems able to call __efx_filter_rfs_expire
on a given channel, it is possible for them to race and thus pass quotas
which, combined, exceed rfs_filter_count. Thus, don't WARN_ON if we loop
all the way around the table with quota left over.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: David Ahern <dahern@digitalocean.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
The old rfs_filters_added method for determining the quota could potentially
allow the NIC to become filled with old filters, which never get tested for
expiry. Instead, explicitly make expiry check work depend on the number of
filters installed, and don't count checking slots without filters in as
doing work. This guarantees that each filter will be checked for expiry at
least once every thirty seconds (assuming the channel to which it belongs is
NAPI polling actively) regardless of fill level.
Signed-off-by: Edward Cree <ecree@solarflare.com>
Tested-by: David Ahern <dahern@digitalocean.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Jeff Kirsher says:
====================
This series contains updates to the ice driver only.
Bruce updates the driver to store the number of functions the device has
so that it won't have to compute it when setting safe mode capabilities.
Adds a check to adjust the reporting of capabilities for devices with
more than 4 ports, which differ for devices with less than 4 ports.
Brett adds a helper function to determine if the VF is allowed to do
VLAN operations based on the host's VF configuration. Also adds a new
function that initializes VLAN stripping (enabled/disabled) for the VF
based on the device supported capabilities. Adds a check if the vector
index is valid with the respect to the number of transmit and receive
queues configured when we set coalesce settings for DCB. Adds a check
if the promisc_mask contains ICE_PROMISC_VLAN_RX or ICE_PROMISC_VLAN_TX
so that VLAN 0 promiscuous rules to be removed. Add a helper macro for
a commonly used de-reference of a pointer to &pf->dev->pdev.
Jesse fixes an issue where if an invalid virtchnl request from the VF,
the driver would return uninitialized data to the VF from the PF stack,
so ensure the stack variable is initialized earlier. Add helpers to the
virtchnl interface make the reporting of strings consistent and help
reduce stack space. Implements VF statistics gathering via the kernel
ndo_get_vf_stats().
Akeem ensures we disable the state flag for each VF when its resources
are returned to the device.
Tony does additional cleanup in the driver to ensure the when we
allocate and free memory within the same function, we should not be
using devm_* variants; use regular alloc and free functions.
Henry implements code to query and set the number of channels on the
primary VSI for a PF via ethtool.
Jake cleans up needless NULL checks in ice_sched_cleanup_all().
Kevin updates the firmware API version to align with current NVM images.
v2: Added "Fixes:" tag to patch 5 commit description and added the use
of netif_is_rxfh_configured() in patch 13 to see if RSS has been
configured by the user, if so do not overwrite that configuration.
====================
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Pull input fix from Dmitry Torokhov:
"Just a single revert as RMI mode should not have been enabled for this
model [yet?]"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - enable RMI mode for X1 Extreme 2nd Generation"
|
|
Export necessary stats for traffic flowing through MQPRIO QoS offload
Tx path.
v2:
- No change.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Implement and export UDP segmentation offload (USO) support for both
NIC and MQPRIO QoS offload Tx path. Update appropriate logic in Tx to
parse GSO info in skb and configure FW_ETH_TX_EO_WR request needed to
perform USO.
v2:
- Remove inline keyword from write_eo_udp_wr() in sge.c. Let the
compiler decide.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
The FW_ETH_TX_EO_WR used for sending UDP Segmentation Offload (USO)
requests expects the headers to be part of the descriptor and the
payload to be part of the SGL containing the DMA mapped addresses.
Hence, the DMA address in the first entry of the SGL can start after
the packet headers. Currently, unmap_sgl() tries to unmap from this
wrong offset, instead of the originally mapped DMA address.
So, use existing unmap_skb() instead, which takes originally saved DMA
addresses as input. Update all necessary Tx paths to save the original
DMA addresses, so that unmap_skb() can unmap them properly.
v2:
- No change.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Minor conflict in drivers/s390/net/qeth_l2_main.c, kept the lock
from commit c8183f548902 ("s390/qeth: fix potential deadlock on
workqueue flush"), removed the code which was removed by commit
9897d583b015 ("s390/qeth: consolidate some duplicated HW cmd code").
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
This reverts commit 68b9c5066e39af41d3448abfc887c77ce22dd64d.
Ugh, I really dropped the ball on this one :\. So as it turns out RMI4
works perfectly fine on the X1 Extreme Gen 2 except for one thing I
didn't notice because I usually use the trackpoint: clicking with the
touchpad. Somehow this is broken, in fact we don't even seem to indicate
BTN_LEFT as a valid event type for the RMI4 touchpad. And, I don't even
see any RMI4 events coming from the touchpad when I press down on it.
This only seems to work for PS/2 mode.
Since that means we have a regression, and PS/2 mode seems to work fine
for the time being - revert this for now. We'll have to do a more
thorough investigation on this.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://lore.kernel.org/r/20191119234534.10725-1-lyude@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Pull networking fixes from David Miller:
1) Validate tunnel options length in act_tunnel_key, from Xin Long.
2) Fix DMA sync bug in gve driver, from Adi Suresh.
3) TSO kills performance on some r8169 chips due to HW issues, disable
by default in that case, from Corinna Vinschen.
4) Fix clock disable mismatch in fec driver, from Chubong Yuan.
5) Fix interrupt status bits define in hns3 driver, from Huazhong Tan.
6) Fix workqueue deadlocks in qeth driver, from Julian Wiedmann.
7) Don't napi_disable() twice in r8152 driver, from Hayes Wang.
8) Fix SKB extension memory leak, from Florian Westphal.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
r8152: avoid to call napi_disable twice
MAINTAINERS: Add myself as maintainer of virtio-vsock
udp: drop skb extensions before marking skb stateless
net: rtnetlink: prevent underflows in do_setvfinfo()
can: m_can_platform: remove unnecessary m_can_class_resume() call
can: m_can_platform: set net_device structure as driver data
hv_netvsc: Fix send_table offset in case of a host bug
hv_netvsc: Fix offset usage in netvsc_send_table()
net-ipv6: IPV6_TRANSPARENT - check NET_RAW prior to NET_ADMIN
sfc: Only cancel the PPS workqueue if it exists
nfc: port100: handle command failure cleanly
net-sysfs: fix netdev_queue_add_kobject() breakage
r8152: Re-order napi_disable in rtl8152_close
net: qca_spi: Move reset_count to struct qcaspi
net: qca_spi: fix receive buffer size check
net/ibmvnic: Ignore H_FUNCTION return from H_EOI to tolerate XIVE mode
Revert "net/ibmvnic: Fix EOI when running in XIVE mode"
net/mlxfw: Verify FSM error code translation doesn't exceed array size
net/mlx5: Update the list of the PCI supported devices
net/mlx5: Fix auto group size calculation
...
|
|
Update FW API minor version to align to current value advertised
by FW in new NVM images.
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The code in ice_sched_cleanup_all checks whether the port info is NULL
prior to calling ice_sched_clear_port. However, ice_sched_clear_port
already checks whether port info is non-NULL.
More importantly, it also checks whether the port structure has been
initialized by checking its port_state field as well.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add code to query and set the number of channels on the primary VSI for a
PF. This is accessed from the 'ethtool -l' and 'ethtool -L' commands,
respectively. Though the ice driver supports asymmetric queues report an
IRQ vector that has both Rx and Tx queues attached and is counted as a
'combined' channel.
Signed-off-by: Henry Tieman <henry.w.tieman@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When code reaches the "out" label, n is guaranteed to be valid so we can
unconditionally call neigh_release.
Also change the label to release_neigh to better reflect the fact that
we unconditionally free the neighbour and also match other labels
convention.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Improve mlx5e_route_lookup_ipv6 function structure by avoiding #ifdef then
return -EOPNOTSUPP in the middle of the function code.
To do so, we stub out mlx5e_tc_tun_create_header_ipv6 which is the only
caller of this helper function to avoid calling it altogether
when ipv6 is compiled out, which should also cleanup some compiler
warnings of unused variables.
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Eli Cohen <eli@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add support for SW steering matching on Geneve header fields:
- VNI
- OAM
- protocol type
- options length
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add definition for flex parser tunneling header for Geneve.
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Refactor flex parser tunnel code:
- Add definition for flex parser tunneling header for VXLAN-GPE
- Use macros for VXLAN-GPE SW steering when building STE
- Refactor the code to reflect that this is a VXLAN GPE
only code and not a general flex parser code.
This also significantly simplifies addition of more
flex parser protocols, such as Geneve.
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The MODIFY_HCA_VPORT_CONTEXT uses field_selector to mask fields needed
to be written, other fields are required to be zero according to the
HW specification. The supported fields are controlled by bitfield
and limited to vport state, node and port GUIDs.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the
ip -s link show dev <PF> command.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The virtchannel interface was repeating a lot of strings
and wasting storage space in the kernel. There was also
inconsistent messages for the same thing. Consolidate all
those messages and bit checks into a couple of helper functions.
Also, reduce stack space usage by simplifying getting the pointer
to the pf using a helper.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We use &pf->dev->pdev all over the code. Add a simple
macro to do this for us. When multiple de-references
like this are being done add a local struct device
variable.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In situations where we alloc and free memory within the same function do
not use the devm_* variants; use regular alloc and free functions. Remove
any unused vars if there are no usages after these changes.
Also, replace an allocate and copy with kmemdup() and remove an
unnecessary memset() to 0 after a kzalloc().
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently ice_clear_vsi_promisc() detects if the VLAN ID sent is not 0
and sets the recipe_id to ICE_SW_LKUP_PROMISC_VLAN in that case and
ICE_SW_LKUP_PROMISC if the VLAN_ID is 0. However this doesn't allow VLAN
0 promiscuous rules to be removed, but they can be added. Fix this by
checking if the promisc_mask contains ICE_PROMISC_VLAN_RX or
ICE_PROMISC_VLAN_TX. This change was made to match what is being done
for ice_set_vsi_promisc().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently there can be a case where a DCB map is applied and there are
more interrupt vectors (vsi->num_q_vectors) than Rx queues (vsi->num_rxq)
and Tx queues (vsi->num_txq). If we try to set coalesce settings in this
case it will report a false failure. Fix this by checking if vector index
is valid with respect to the number of Tx and Rx queues configured.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It is wrong to set PF disable state flag for all VFs when freeing VF
resources - Instead, we should set VF disable state flag for each VF with
its resources being returned to the device. Right now, all VF opcodes,
mailbox communication to clear its resources as well fails - since we
already indicate that PF is in disable state, with all VFs not active. In
addition, we don't need to notify VF that PF is intending to reset it, if
it is already in disabled state.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the case of an invalid virtchannel request the driver
would return uninitialized data to the VF from the PF stack
which is a bug. Fix by initializing the stack variable
earlier in the function before any return paths can be taken.
Fixes: 1071a8358a28 ("ice: Implement virtchnl commands for AVF support")
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently when adding/deleting vlans in ice_vc_process_vlan_msg()
we are calling ice_vsi_manage_vlan_stripping() to enable/disable
when adding and deleting a VLAN respectively. This is wrong
because adding/deleting VLANs has nothing to do with configuring
VLAN stripping. VLAN stripping is configured through the
following VIRTCHNL operations:
VIRTCHNL_OP_ENABLE_VLAN_STRIPPING
VIRTCHNL_OP_DISABLE_VLAN_STRIPPING
Unfortunately we can't just remove this because then stripping
will never be configured on VF initialization. Fix this by
adding a new function that initializes (disables/enables) VLAN
stripping for the VF based on the device supported capabilities.
This allows us to remove the call to
ice_vsi_manage_vlan_stripping() in ice_vc_process_vlan_msg().
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently if the host disables VLAN offloads on the VF by
not setting the VIRTCHNL_VF_OFFLOAD_VLAN capability bit
we will still honor VF VLAN configuration messages over
VIRTCHNL. These messages (i.e. enable/disable VLAN stripping
and VLAN filtering) should be blocked when the feature
is not supported. Fix that by adding a helper function to
determine if the VF is allowed to do VLAN operations based
on the host's VF configuration.
Also, mirror the VF communicated capabilities in the host's
VF configuration.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Firmware always returns 8 as the max number of supported TCs. However on
devices with more than 4 ports, the maximum number of TCs per port is
limited to 4. Check and, if necessary, correct the reporting of
capabilities for devices with more than 4 ports.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Store the number of functions the device has and use this number when
setting safe mode capabilities instead of calculating it.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Co-developed-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Kevin Scott <kevin.c.scott@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix following sparse warnings:
drivers/net/dsa/ocelot/felix.c:351:6: warning: symbol 'felix_txtstamp' was not declared. Should it be static?
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call napi_disable() twice would cause dead lock. There are three situations
may result in the issue.
1. rtl8152_pre_reset() and set_carrier() are run at the same time.
2. Call rtl8152_set_tunable() after rtl8152_close().
3. Call rtl8152_set_ringparam() after rtl8152_close().
For #1, use the same solution as commit 84811412464d ("r8152: Re-order
napi_disable in rtl8152_close"). For #2 and #3, add checking the flag
of IFF_UP and using napi_disable/napi_enable during mutex.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Two sets of fixes in here, one for amdgpu, and one for i915.
The amdgpu ones are pretty small, i915's CI system seems to have a few
problems in the last week or so, there is one major regression fix for
fb_mmap, but there are a bunch of other issues fixed in there as well,
oops, screen flashes and rcu related.
amdgpu:
- Remove experimental flag for navi14
- Fix confusing power message failures on older VI parts
- Hang fix for gfxoff when using the read register interface
- Two stability regression fixes for Raven
i915:
- Fix kernel oops on dumb_create ioctl on no crtc situation
- Fix bad ugly colored flash on VLV/CHV related to gamma LUT update
- Fix unity of the frequencies reported on PMU
- Fix kernel oops on set_page_dirty using better locks around it
- Protect the request pointer with RCU to prevent it being freed
while we might need still
- Make pool objects read-only
- Restore physical addresses for fb_map to avoid corrupted page
table"
* tag 'drm-fixes-2019-11-22' of git://anongit.freedesktop.org/drm/drm:
drm/i915/fbdev: Restore physical addresses for fb_mmap()
Revert "drm/amd/display: enable S/G for RAVEN chip"
drm/amdgpu: disable gfxoff on original raven
drm/amdgpu: disable gfxoff when using register read interface
drm/amd/powerplay: correct fine grained dpm force level setting
drm/amd/powerplay: issue no PPSMC_MSG_GetCurrPkgPwr on unsupported ASICs
drm/amdgpu: remove experimental flag for Navi14
drm/i915: make pool objects read-only
drm/i915: Protect request peeking with RCU
drm/i915/userptr: Try to acquire the page lock around set_page_dirty()
drm/i915/pmu: "Frequency" is reported as accumulated cycles
drm/i915: Preload LUTs if the hw isn't currently using them
drm/i915: Don't oops in dumb_create ioctl if we have no crtcs
|
|
The function m_can_runtime_resume() is getting recursively called from
m_can_class_resume(). This results in a lock up.
We need not call m_can_class_resume() during m_can_runtime_resume().
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The current code is failing during clock prepare enable because of not
getting proper clock from platform device.
[ 0.852089] Call trace:
[ 0.854516] 0xffff0000fa22a668
[ 0.857638] clk_prepare+0x20/0x34
[ 0.861019] m_can_runtime_resume+0x2c/0xe4
[ 0.865180] pm_generic_runtime_resume+0x28/0x38
[ 0.869770] __rpm_callback+0x16c/0x1bc
[ 0.873583] rpm_callback+0x24/0x78
[ 0.877050] rpm_resume+0x428/0x560
[ 0.880517] __pm_runtime_resume+0x7c/0xa8
[ 0.884593] m_can_clk_start.isra.9.part.10+0x1c/0xa8
[ 0.889618] m_can_class_register+0x138/0x370
[ 0.893950] m_can_plat_probe+0x120/0x170
[ 0.897939] platform_drv_probe+0x4c/0xa0
[ 0.901924] really_probe+0xd8/0x31c
[ 0.905477] driver_probe_device+0x58/0xe8
[ 0.909551] device_driver_attach+0x68/0x70
[ 0.913711] __driver_attach+0x9c/0xf8
[ 0.917437] bus_for_each_dev+0x50/0xa0
[ 0.921251] driver_attach+0x20/0x28
[ 0.924804] bus_add_driver+0x148/0x1fc
[ 0.928617] driver_register+0x6c/0x124
[ 0.932431] __platform_driver_register+0x48/0x50
[ 0.937113] m_can_plat_driver_init+0x18/0x20
[ 0.941446] do_one_initcall+0x4c/0x19c
[ 0.945259] kernel_init_freeable+0x1d0/0x280
[ 0.949591] kernel_init+0x10/0x100
[ 0.953057] ret_from_fork+0x10/0x18
[ 0.956614] Code: 00000000 00000000 00000000 00000000 (fa22a668)
[ 0.962681] ---[ end trace 881f71bd609de763 ]---
[ 0.967301] Kernel panic - not syncing: Attempted to kill init!
A device driver for CAN controller hardware registers itself with the
Linux network layer as a network device. So, the driver data for m_can
should ideally be of type net_device.
Fixes: f524f829b75a ("can: m_can: Create a m_can platform framework")
Signed-off-by: Pankaj Sharma <pankj.sharma@samsung.com>
Signed-off-by: Sriram Dash <sriram.dash@samsung.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When virt_wifi interface is created, virt_wifi_newlink() is called and
it calls register_netdevice().
if register_netdevice() fails, it internally would call
->priv_destructor(), which is virt_wifi_net_device_destructor() and
it frees netdev. but virt_wifi_newlink() still use netdev.
So, use-after-free would occur in virt_wifi_newlink().
Test commands:
ip link add dummy0 type dummy
modprobe bonding
ip link add bonding_masters link dummy0 type virt_wifi
Splat looks like:
[ 202.220554] BUG: KASAN: use-after-free in virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.221659] Read of size 8 at addr ffff888061629cb8 by task ip/852
[ 202.222896] CPU: 1 PID: 852 Comm: ip Not tainted 5.4.0-rc5 #3
[ 202.223765] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006
[ 202.225073] Call Trace:
[ 202.225532] dump_stack+0x7c/0xbb
[ 202.226869] print_address_description.constprop.5+0x1be/0x360
[ 202.229362] __kasan_report+0x12a/0x16f
[ 202.230714] kasan_report+0xe/0x20
[ 202.232595] virt_wifi_newlink+0x88b/0x9a0 [virt_wifi]
[ 202.233370] __rtnl_newlink+0xb9f/0x11b0
[ 202.244909] rtnl_newlink+0x65/0x90
[ ... ]
Cc: stable@vger.kernel.org
Fixes: c7cdba31ed8b ("mac80211-next: rtnetlink wifi simulation device")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20191121122645.9355-1-ap420073@gmail.com
[trim stack dump a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Some devices ship with the controller default address, like the
Orange Pi 3 (BCM4345C5).
Allow the bootloader to set a valid address through the device tree.
Signed-off-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
In the vmx crypto Makefile we assign to a variable called TARGET and
pass that to the aesp8-ppc.pl and ghashp8-ppc.pl scripts.
The variable is meant to describe what flavour of powerpc we're
building for, eg. either 32 or 64-bit, and big or little endian.
Unfortunately TARGET is a fairly common name for a make variable, and
if it happens that TARGET is specified as a command line parameter to
make, the value specified on the command line will override our value.
In particular this can happen if the kernel Makefile is driven by an
external Makefile that uses TARGET for something.
This leads to weird build failures, eg:
nonsense at /build/linux/drivers/crypto/vmx/ghashp8-ppc.pl line 45.
/linux/drivers/crypto/vmx/Makefile:20: recipe for target 'drivers/crypto/vmx/ghashp8-ppc.S' failed
Which shows that we passed an empty value for $(TARGET) to the perl
script, confirmed with make V=1:
perl /linux/drivers/crypto/vmx/ghashp8-ppc.pl > drivers/crypto/vmx/ghashp8-ppc.S
We can avoid this confusion by using override, to tell make that we
don't want anything to override our variable, even a value specified
on the command line. We can also use a less common name, given the
script calls it "flavour", let's use that.
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
On big endian kernel, the GXL crypto driver does not works.
This patch do the necessary modification to permit it to work on BE
kernel (removing bitfield and adds some cpu_to_le32).
Fixes: 48fe583fe541 ("crypto: amlogic - Add crypto accelerator for amlogic GXL")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
On big endian kernel, the sun8i-ce crypto driver does not works.
This patch do the necessary modification to permit it to work on BE
kernel (setting descriptor entries as __le32 and adding some cpu_to_le32)
Fixes: 06f751b61329 ("crypto: allwinner - Add sun8i-ce Crypto Engine")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch enables COMPILE_TEST on the ks-sa-rng driver.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In case of in-place decryption, the "lastc" buffer is used to copy
the last ciphertext block before the decryption of the message. It
is later used to update the req->iv of the skcipher_request.
"lastc" variable is not used to interact with the hardware, there
is no restriction to be of type "u32". Change the type of "lastc"
to "u8".
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The req->iv of the skcipher_request is expected to contain the
last ciphertext block when the {en,de}crypt operation is done.
In case of in-place decryption, copy the ciphertext in an
intermediate buffer before decryption.
This fixes the following tcrypt tests:
alg: skcipher: atmel-cbc-des encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
00000000: fe dc ba 98 76 54 32 10
alg: skcipher: atmel-cbc-tdes encryption test failed (wrong output IV) on test vector 0, cfg="in-place"
00000000: 7d 33 88 93 0f 93 b2 42
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When testing BigEndian kernel, the sun4i-ss was failling all crypto
tests.
This patch fix endian issues with it.
Fixes: 6298e948215f ("crypto: sunxi-ss - Add Allwinner Security System crypto accelerator")
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
Jakub Kicinski
Russell King
Edward Cree
Linus Torvalds
Rahul Lakkireddy
Lyude Paul
Kevin Scott
Jacob Keller
Henry Tieman
Eli Cohen
Saeed Mahameed
Yevgeny Kliteynik
Leon Romanovsky
Jesse Brandeburg
Brett Creeley
Tony Nguyen
Akeem G Abodunrin
Bruce Allan
Chen Wandun
Hayes Wang
Pankaj Sharma
Taehee Yoo
Andre Heider
Michael Ellerman
Corentin Labbe
Corentin Labbe
Herbert Xu
Tudor Ambarus