| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
alloc_etherdev has a generic OOM/unable to alloc message.
Remove the duplicative messages after alloc_etherdev calls.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rtl8169_get_regs operates under RTNL and rtl task mutex whereas
rtl_set_rx_mode is either called under RTNL or rtl task mutex protection.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
Simpler, more consistent, with negligible cost in non-critical paths.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
- atomic bit operations are globally visible
- pending status is always cleared before execution
- scheduled works are either idempotent or only required to happen once
after a series of originating events, say link events for instance
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Suggested-by: Michał Mirosław <mirqus@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
With infinite gratitude to Eric Dumazet for allowing me to identify
the error.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
|
|
This code is clearly unused, since it has a #error right
in it. Given the vintage of sun3 hardware, it is probably
safe to assume that there is little interest in adding new
functionality to the driver now, so just delete the unused
block of code.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Sam Creasey <sammy@sammy.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The reorganization of the driver layout in drivers/net
left behind some stale paths in comments and in Kconfig
help text. Bring them up to date. No actual change to
any code takes place here.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This function returns the page offset of the buffer, which can be
calculated based on either its DMA address or its virtual address. It
used to use the virtual address and we would cast that to unsigned
long, as anything smaller would result in a compiler warning. Now
that it's using the DMA address we should use unsigned int, matching
the return type. It is also unnecessary to use __force.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
<linux/mtd/mtd.h> no longer defines DEBUG so we do not need to
un-define it here.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
|
|
The irq handler was a mess.
See 7ab87ff4c770eed71e3777936299292739fcd0fe ("via-rhine: move work from
irq handler to softirq and beyond") for similar changes. One can notice:
- all non-napi tasks are explicitely scheduled trough a single work queue.
- hiding software tx queue start behind the rtl_hw_start method is mildly
natural. Move it in the caller where needed.
- as can be seen from the heavy use of bh disabling locks, the driver is
not safe for irq context messages with netconsole. It is still quite
usable for general messaging though. Tested ok with concurrent registers
dump (ethtool -d) + background traffic + "echo t > /proc/sysrq-trigger".
Tested with old PCI chipset, PCIe 8168 and 810x:
- XID 0c900800 RTL8168evl/8111evl
- XID 18000000 RTL8168b/8111b
- XID 98000000 RTL8169sc/8110sc
- XID 083000c0 RTL8168d/8111d
- XID 081000c0 RTL8168d/8111d
- XID 00b00000 RTL8105e
- XID 04a00000 RTL8102e
As a side note, the comments in f11a377b3f4e897d11f0e8d1fc688667e2f19708
("r8169: avoid losing MSI interrupts") does not seem completely clear: if
I hack the driver further to stop acking the irq link event bit, MSI
interrupts keep being delivered (RTL8168b/8111b, XID 18000000).
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
Though motivated by the move of the driver to a single work queue of
sequential events and removal of hard irq processing, it looks safe as
a standalone change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
I see no good reason to keep both rtl8169_reinit_task and rtl8169_reset_task:
- rtl8169_reinit_task adds a software failure point which does relate to
any hardware state
- they handle hardware the same. Remember that rtl8169_reinit_task was
introduced in the 8169 only era to handle PCI errors way before the 8168
asked for pll and firmware ops and compare :
rtl8169_reinit_task | rtl8169_reset_task
----------------------------+--------------------------
rtl8169_wait_for_quiescence | rtl8169_hw_reset
rtl8169_update_counters | rtl8169_wait_for_quiescence
rtl8169_hw_reset | rtl_hw_start
rtl8169_rx_missed | rtl8169_check_link_status
rtl_pll_power_down |
rtl_request_firmware |
rtl8169_init_phy |
rtl_pll_power_up |
rtl_hw_start |
rtl8169_check_link_status |
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Hayes Wang <hayeswang@realtek.com>
|
|
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The generic lib.c file contains code relative to the various MACs, NVM and
Manageability supported by the driver. This patch splits the file into
three which are specific to those areas similar to how the PHY-specific
code is in phy.c and code specific to the 80003es2lan, 8257x, and ichX
MAC families are in their own files. The generic code that is applicable
to all MAC/PHY parts supported by the driver remains in netdev.c, param.c
and ethtool.c files. No change in functionality, just moving code
around for ease of maintenance, with some whitespace and other checkpatch
cleanups.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
__er16flash() is not meant to be called directly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Convert the last instances of strncpy() to the preferred strlcpy().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
To ease searching for debug message strings, concatenate strings that span
multiple lines even if the resulting line exceeds 80 columns; these will
not cause checkpatch warnings.
Also, add '\n' and remove unnecessary '\r' from a few debug strings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When setting the Low Power Link Up (LPLU, a.k.a. reverse auto-negotiation)
on 82577/8278/82579, do not restart auto-negotiation if reset of the Phy is
blocked by the Manageability Engine.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
During bi-directional stress on some 82566/82567 devices, some received
packets were dropped. Increasing the Receive Packet Buffer Allocation
resolves this.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When going to Sx with an ICHx/PCH device, the default Low Power Link Up
(LPLU, a.k.a. reverse auto-negotiation) behavior should be whatever is set
in the NVM. However, the function e1000_suspend_workarounds_ich8lan()
called when going to Sx always enabled LPLU in all power states.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The workaround which toggles the LANPHYPC (LAN PHY Power Control) value bit
to force the MAC-Phy interconnect into PCIe mode from SMBus mode during
driver load and resume should always be done except if PHY resets are
blocked by the Manageability Engine (ME). Previously, the toggle was done
only if PHY resets are blocked and the ME was disabled.
The rest of the patch is just indentation changes as a consequence of the
updated workaround.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Internal stress testing with jumbo frames shows the reliability of ICH9 and
ICH10D devices is improved in certain corner cases by disabling the Early
Receive feature. To reduce the performance impact caused by disabling this
feature, the packet buffer sizes and relevant flow control settings are
modified accordingly.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Replace checksummed and discard booleans from efx_handle_rx_event()
with a bitmask, added to the flags field.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Currently we use type u64 for byte counts, which can very quickly
exceed 2^32, and unsigned long for packet counts, which do not. But
it can still take only 20-something minutes to send or receive 2^32
packets, and not all tools properly handle overflow even if they
sample more often than this.
The MAC statistics are all updated synchronously, so it costs very
little to make them all 64-bit regardless of native word size.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Rename efx_set_multicast_list() to efx_set_rx_mode(), in line
with the operation name net_device_ops::ndo_set_rx_mode.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The out-of-tree version of the sfc driver used to run a self-test on
each device before registering it. Although this was never included
in-tree, some functions have checks for this special case which is not
really possible.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
SFC4000 boards also have an EEPROM exposed as MTD.
The boot configuration is accessed through MTD.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The SFC9000-family controllers have firmware to manage all board
peripherals including temperature, heat sink continuity and voltage
sensors. The firmware reports sensor alarms, which we log, and
will shut down the board if necessary.
Some users may want to monitor their boards more closely, so add an
hwmon driver that exposes all sensors reported by the firmware. Move
efx_mcdi_sensor_event() into the new file so it can share the array of
sensor labels with the hwmon driver.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Interrupts are normally generated by the event queues, moderated by
timers. However, they may also be triggered by detection of a 'fatal'
error condition (e.g. memory parity error) or by the host writing to
certain CSR fields as part of a self-test.
The IRQ level/index used for these on Falcon rev B0 and Siena is set
by the KER_INT_LEVE_SEL field and cached by the driver in
efx_nic::fatal_irq_level. Since this value is also relevant to
self-tests rename the field to just 'irq_level'.
Avoid unnecessary cache traffic by using a per-channel 'last_irq_cpu'
field and only writing to the per-controller field when the interrupt
matches efx_nic::irq_level. Remove the volatile qualifier and use
ACCESS_ONCE in the places we read these fields.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
This reverts commit 6369545945b90daa1a73fca174da9194c398417c in
drivers/net/ethernet/sfc/falcon.c.
Unlike the INT_ISR0 register on later controller revisions, the
NET_IVEC_INT_Q bits written to memory are only ever set for
interrupting event queues, not for any other interrupt sources.
By definition there can only be one legacy interrupt handler per
function, so there is no need to worry about detecting a fatal
interrupt more than once.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We cannot safely assume that the NAPI handler will complete within the
20 ms that we allow for the event self-test. The handler may be
deferred for longer than this, particularly on realtime kernels.
Instead, check whether either an event has been handled or (as in the
old failure path) whether an interrupt has been received and an event
has been delivered but not yet handled. Use napi_disable() to
synchronize with the NAPI handler before checking, since it will
clear events before updating eventq_read_ptr.
Remove the test result chan.N.eventq.poll, since it is not an error
if the NAPI handler does not run during the test.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
We currently assume that the timer quantum for Siena is 5 us, the same
as for Falcon. This is not correct; timer ticks are generated on a
rota which takes a minimum of 768 cycles (each event delivery or other
timer change will delay it by 3 cycles). The timer quantum should be
6.144 or 3.072 us depending on whether turbo mode is active.
Replace EFX_IRQ_MOD_RESOLUTION with a timer_quantum_ns field in struct
efx_nic, initialised by the efx_nic_type::probe function.
While we're at it, replace EFX_IRQ_MOD_MAX with a timer_period_max
field in struct efx_nic_type.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
The netif_dbg() macro is defined in <linux/netdevice.h>. If the DEBUG
macro is defined, it logs a message at 'debug' level, otherwise it
does nothing.
In net_driver.h we define DEBUG if EFX_ENABLE_DEBUG is defined, but
this is too late for those source files that already got a
definition of netif_dbg() by including <linux/netdevice.h>
Get rid of EFX_ENABLE_DEBUG, and only define and test DEBUG.
In mtd.c, we do not use DEBUG as a condition flag but are forced to
use the DEBUG macro-function from <linux/mtd/mtd.h>. Undefine DEBUG
before including it.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
|
Both implementations of efx_nic_type::reconfigure_mac operation
push the multicast hash filter to the hardware. It is therefore
redundant to call efx_nic_type::push_multicast_hash as well.
efx_mcdi_mac_reconfigure() also uses this operation, but the
implementation for Siena just uses MCDI anyway. Merge that into
efx_mcdi_mac_reconfigure().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
|
Joe Perches
Francois Romieu
David S. Miller
Paul Gortmaker
Ben Hutchings
Bruce Allan
Matthew Slattery