| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
In addition to PCIe and Display Port tunnels it is also possible to
create tunnels that forward DMA traffic from the host interface adapter
(NHI) to a NULL port that is connected to another domain through a
Thunderbolt cable. These tunnels can be used to carry software messages
such as networking packets.
To support this we introduce another tunnel type (TB_TUNNEL_DMA) that
supports paths from NHI to NULL port and back.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently ICM has been handling XDomain UUID exchange so there was no
need to have it in the driver yet. However, since now we are going to
add the same capabilities to the software connection manager it needs to
be handled properly.
For this reason modify the driver XDomain protocol handling so that if
the remote domain UUID is not filled in the core will query it first and
only then start the normal property exchange flow.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We run all XDomain requests during discovery in tb->wq and since it only
runs one work at the time it means that sending back reply to the other
domain may be delayed too much depending whether there is an active
XDomain discovery request running.
To make sure we can send reply to the other domain as soon as possible
run tb_xdp_handle_request() in system workqueue instead. Since the
device can be hot-removed in the middle we need to make sure the domain
structure is still around when the function is run so increase reference
count before we schedule the reply work.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Now that we have capability to discover existing tunnels during driver
load there is no point tearing down tunnels when the driver gets
unloaded. Instead we can just leave them running. If user disconnects
devices while there is no Thunderbolt driver loaded, tunneled protocol
hotplug happens and is handled by the corresponding driver (pciehp in
case of PCIe tunnel, GFX driver in case of DP tunnel).
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
NFC (non flow control) credits is actually 20-bit field so update
tb_port_add_nfc_credits() to handle this properly. This allows us to set
NFC credits for Display Port path in subsequent patches.
Also make sure the function does not update the hardware if the
underlying switch is already unplugged.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We will be needing these routines to find Display Port adapters as well
so modify them to take port type as the second parameter.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The only way to expand Thunderbolt topology is through the NULL adapter
ports (typically ports 1, 2, 3 and 4). There is no point handling
Thunderbolt hotplug events on any other port.
Add a helper function (tb_port_is_null()) that can be used to determine
if the port is NULL port, and use it in software connection manager code
when hotplug event is handled.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Currently the software connection manager (tb.c) has only supported
creating a single PCIe tunnel, no PCIe device daisy chaining has been
supported so far. This updates the software connection manager so that
it now can create PCIe tunnels for full chain of six devices.
Because PCIe allows DMA and opens possibility for DMA attacks we change
security level to "user" meaning that PCIe tunneling requires that the
userspace authorizes the devices first. This makes it possible to block
PCIe tunneling completely while still allowing other types of tunnels to
be automatically created.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In Apple Macs the boot firmware (EFI) connects all devices automatically
when the system is started, before it hands over to the OS. Instead of
ignoring we discover all those PCIe tunnels and record them using our
internal structures, just like we do when a device is connected after
the OS is already up.
By doing this we can properly tear down tunnels when devices are
disconnected. Also this allows us to resume the existing tunnels after
system suspend/resume cycle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
State of the connected devices and tunnel configuration is not known
during resume. For example some paths may not be complete anymore if the
user has unplugged the related devices. So instead of marking all paths
as inactive we go ahead and deactivate them explicitly before we restart
them.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Now that we can allocate hop IDs per port on a path, we can take
advantage of this and create tunnels covering longer paths than just
between two adjacent switches. PCIe actually does not need this as it
is typically a daisy chain between two adjacent switches but this way we
do not need to hard-code creation of the tunnel.
While there add name to struct tb_path to make debugging easier, and
update kernel-doc comments.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We need to be able to walk from one port to another when we are creating
paths where there are multiple switches between two ports. For this
reason introduce a new function tb_next_port_on_path().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
|
|
Currently the driver only assigns remote port for the primary port if in
case of dual link. This makes things such as walking from one port to
another more complex than necessary because the code needs to change
from secondary to primary port if the path that is established is
created using secondary links.
In order to always assign both remote pointers we need to prevent the
scanning code from following the secondary link. Failing to do that
might cause problems as the same switch may be enumerated twice (or
removed in case of unplug). Handle that properly by introducing a new
function tb_port_has_remote() that returns true only for the primary
port. We also update tb_is_upstream_port() to support both dual link
ports, make it take const port pointer and move it below
tb_upstream_port() to keep similar functions close.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Each port has a separate path configuration space that is used for
finding the next hop (switch) in the path. HopID is an index to this
configuration space. HopIDs 0 - 7 are reserved by the protocol.
In order to get next available HopID for each direction we provide two
pairs of helper functions that can be used to allocate and release
HopIDs for a given port.
While there remove obsolete TODO comment.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.
We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In order to tunnel non-PCIe traffic as well rename tunnel_pci.[ch] to
tunnel.[ch] to reflect this fact. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The adapter specific capability either is there or not if the port does
not hold an adapter. Instead of always finding it on-demand we read the
offset just once when the port is initialized.
While there we update the struct port documentation to follow kernel-doc
format.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We need to wait until all buffers have been drained before the path can
be considered disabled. Do this for every hop in a path.
This adds another bit field to struct tb_regs_hop even if we are trying
to get rid of them but we can clean them up another day.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Thunderbolt 2 devices and beyond link controller needs to be notified
when a switch is going to be suspended by setting bit 31 in LC_SX_CTRL
register. Add this functionality to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Thunderbolt 2 devices and beyond need to have additional bits set in
link controller specific registers. This includes two bits in LC_SX_CTRL
that tell the link controller which lane is connected and whether it is
upstream facing or not.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
We will be adding more link controller functionality in subsequent
patches and it does not make sense to keep all that in switch.c, so
separate LC functionality into its own file.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Light Ridge has an issue where reading the next capability pointer
location in port config space the read data is not cleared. It is fine
to read capabilities each after another so only thing we need to do is
to make sure we issue dummy read after tb_port_find_cap() is finished to
avoid the issue in next read.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Light Ridge and Eagle Ridge both need to have TMU access enabled before
port space can be fully accessed so make sure it happens on those. This
allows us to get rid of the offset quirk in tb_port_find_cap().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Maximum depth in Thunderbolt topology is 6 so make sure it is not
possible to allocate switches that exceed the depth limit.
While at it update tb_switch_alloc() to use upper/lower_32_bits()
following tb_switch_alloc_safe_mode().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
switch_lock was introduced because it allowed serialization of device
authorization requests from userspace without need to take the big
domain lock (tb->lock). This was fine because device authorization with
ICM is just one command that is sent to the firmware. Now that we start
to handle all tunneling in the driver switch_lock is not enough because
we need to walk over the topology to establish paths.
For this reason drop switch_lock from the driver completely in favour of
big domain lock.
There is one complication, though. If userspace is waiting for the lock
in tb_switch_set_authorized(), it keeps the device_del() from removing
the sysfs attribute because it waits for active users to release the
attribute first which leads into following splat:
INFO: task kworker/u8:3:73 blocked for more than 61 seconds.
Tainted: G W 5.1.0-rc1+ #244
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
kworker/u8:3 D12976 73 2 0x80000000
Workqueue: thunderbolt0 tb_handle_hotplug [thunderbolt]
Call Trace:
? __schedule+0x2e5/0x740
? _raw_spin_lock_irqsave+0x12/0x40
? prepare_to_wait_event+0xc5/0x160
schedule+0x2d/0x80
__kernfs_remove.part.17+0x183/0x1f0
? finish_wait+0x80/0x80
kernfs_remove_by_name_ns+0x4a/0x90
remove_files.isra.1+0x2b/0x60
sysfs_remove_group+0x38/0x80
sysfs_remove_groups+0x24/0x40
device_remove_attrs+0x3d/0x70
device_del+0x14c/0x360
device_unregister+0x15/0x50
tb_switch_remove+0x9e/0x1d0 [thunderbolt]
tb_handle_hotplug+0x119/0x5a0 [thunderbolt]
? process_one_work+0x1b7/0x420
process_one_work+0x1b7/0x420
worker_thread+0x37/0x380
? _raw_spin_unlock_irqrestore+0xf/0x30
? process_one_work+0x420/0x420
kthread+0x118/0x130
? kthread_create_on_node+0x60/0x60
ret_from_fork+0x35/0x40
We deal this by following what network stack did for some of their
attributes and use mutex_trylock() with restart_syscall(). This makes
userspace release the attribute allowing sysfs attribute removal to
progress before the write is restarted and eventually fail when the
attribute is removed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
If switch is already disconnected there is no point sending it commands
and waiting for timeout. Instead in that case return error immediately.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
tb_switch_find_by_route() does the same already so use it instead and
remove duplicated get_switch_at_route().
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
|
|
This field is not used anywhere so remove it.
Reported-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
The XDomain protocol messages may start as soon as Thunderbolt control
channel is started. This means that if the other host starts sending
ThunderboltIP packets early enough they will be passed to the network
driver which then gets confused because its resume hook is not called
yet.
Fix this by unregistering the ThunderboltIP protocol handler when
suspending and registering it back on resume.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
|
|
uuid in add_switch is allocted via kmemdup which can fail. The patch
logs the error and cleans up the allocated memory for switch.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
No check is enforced for the return value of kzalloc,
which may lead to NULL-pointer dereference.
The patch fixes this issue.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
kmemdup can fail and return a NULL pointer. The patch modifies the
signature of tb_xdp_schedule_request and passes the failure error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In enumerate_services, ida_simple_get on failure can return an error and
leaks memory. The patch ensures that the dev_set_name is set on non
failure cases, and releases memory during failure.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Memory allocated via kmemdup might fail and return a NULL pointer.
This patch adds a check on the return value of kmemdup and passes the
error upstream.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Reviewed-by: Mukesh Ojha <mojha@codeaurora.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
kmemdup may fail and return NULL. The fix adds a check and returns
NULL in case it fails to avoid NULL pointer dereferecen.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
In case kzalloc fails, the fix releases resources and returns
-ENOMEM to avoid the NULL pointer dereference.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
|
|
Pull xen fix from Juergen Gross:
"A fix for a Xen bug introduced by David's series for excluding
ballooned pages in vmcores"
* tag 'for-linus-5.1b-rc1b-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/balloon: Fix mapping PG_offline pages to user space
|
|
Pull device-dax updates from Dan Williams:
"New device-dax infrastructure to allow persistent memory and other
"reserved" / performance differentiated memories, to be assigned to
the core-mm as "System RAM".
Some users want to use persistent memory as additional volatile
memory. They are willing to cope with potential performance
differences, for example between DRAM and 3D Xpoint, and want to use
typical Linux memory management apis rather than a userspace memory
allocator layered over an mmap() of a dax file. The administration
model is to decide how much Persistent Memory (pmem) to use as System
RAM, create a device-dax-mode namespace of that size, and then assign
it to the core-mm. The rationale for device-dax is that it is a
generic memory-mapping driver that can be layered over any "special
purpose" memory, not just pmem. On subsequent boots udev rules can be
used to restore the memory assignment.
One implication of using pmem as RAM is that mlock() no longer keeps
data off persistent media. For this reason it is recommended to enable
NVDIMM Security (previously merged for 5.0) to encrypt pmem contents
at rest. We considered making this recommendation an actively enforced
requirement, but in the end decided to leave it as a distribution /
administrator policy to allow for emulation and test environments that
lack security capable NVDIMMs.
Summary:
- Replace the /sys/class/dax device model with /sys/bus/dax, and
include a compat driver so distributions can opt-in to the new ABI.
- Allow for an alternative driver for the device-dax address-range
- Introduce the 'kmem' driver to hotplug / assign a device-dax
address-range to the core-mm.
- Arrange for the device-dax target-node to be onlined so that the
newly added memory range can be uniquely referenced by numa apis"
NOTE! I'm not entirely happy with the whole "PMEM as RAM" model because
we currently have special - and very annoying rules in the kernel about
accessing PMEM only with the "MC safe" accessors, because machine checks
inside the regular repeat string copy functions can be fatal in some
(not described) circumstances.
And apparently the PMEM modules can cause that a lot more than regular
RAM. The argument is that this happens because PMEM doesn't necessarily
get scrubbed at boot like RAM does, but that is planned to be added for
the user space tooling.
Quoting Dan from another email:
"The exposure can be reduced in the volatile-RAM case by scanning for
and clearing errors before it is onlined as RAM. The userspace tooling
for that can be in place before v5.1-final. There's also runtime
notifications of errors via acpi_nfit_uc_error_notify() from
background scrubbers on the DIMM devices. With that mechanism the
kernel could proactively clear newly discovered poison in the volatile
case, but that would be additional development more suitable for v5.2.
I understand the concern, and the need to highlight this issue by
tapping the brakes on feature development, but I don't see PMEM as RAM
making the situation worse when the exposure is also there via DAX in
the PMEM case. Volatile-RAM is arguably a safer use case since it's
possible to repair pages where the persistent case needs active
application coordination"
* tag 'devdax-for-5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
device-dax: "Hotplug" persistent memory for use like normal RAM
mm/resource: Let walk_system_ram_range() search child resources
mm/memory-hotplug: Allow memory resources to be children
mm/resource: Move HMM pr_debug() deeper into resource code
mm/resource: Return real error codes from walk failures
device-dax: Add a 'modalias' attribute to DAX 'bus' devices
device-dax: Add a 'target_node' attribute
device-dax: Auto-bind device after successful new_id
acpi/nfit, device-dax: Identify differentiated memory with a unique numa-node
device-dax: Add /sys/class/dax backwards compatibility
device-dax: Add support for a dax override driver
device-dax: Move resource pinning+mapping into the common driver
device-dax: Introduce bus + driver model
device-dax: Start defining a dax bus model
device-dax: Remove multi-resource infrastructure
device-dax: Kill dax_region base
device-dax: Kill dax_region ida
|
|
Pull more SCSI updates from James Bottomley:
"This is the final round of mostly small fixes and performance
improvements to our initial submit.
The main regression fix is the ia64 simscsi build failure which was
missed in the serial number elimination conversion"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (24 commits)
scsi: ia64: simscsi: use request tag instead of serial_number
scsi: aacraid: Fix performance issue on logical drives
scsi: lpfc: Fix error codes in lpfc_sli4_pci_mem_setup()
scsi: libiscsi: Hold back_lock when calling iscsi_complete_task
scsi: hisi_sas: Change SERDES_CFG init value to increase reliability of HiLink
scsi: hisi_sas: Send HARD RESET to clear the previous affiliation of STP target port
scsi: hisi_sas: Set PHY linkrate when disconnected
scsi: hisi_sas: print PHY RX errors count for later revision of v3 hw
scsi: hisi_sas: Fix a timeout race of driver internal and SMP IO
scsi: hisi_sas: Change return variable type in phy_up_v3_hw()
scsi: qla2xxx: check for kstrtol() failure
scsi: lpfc: fix 32-bit format string warning
scsi: lpfc: fix unused variable warning
scsi: target: tcmu: Switch to bitmap_zalloc()
scsi: libiscsi: fall back to sendmsg for slab pages
scsi: qla2xxx: avoid printf format warning
scsi: lpfc: resolve static checker warning in lpfc_sli4_hba_unset
scsi: lpfc: Correct __lpfc_sli_issue_iocb_s4 lockdep check
scsi: ufs: hisi: fix ufs_hba_variant_ops passing
scsi: qla2xxx: Fix panic in qla_dfs_tgt_counters_show
...
|
|
Pull more block layer changes from Jens Axboe:
"This is a collection of both stragglers, and fixes that came in after
I finalized the initial pull. This contains:
- An MD pull request from Song, with a few minor fixes
- Set of NVMe patches via Christoph
- Pull request from Konrad, with a few fixes for xen/blkback
- pblk fix IO calculation fix (Javier)
- Segment calculation fix for pass-through (Ming)
- Fallthrough annotation for blkcg (Mathieu)"
* tag 'for-5.1/block-post-20190315' of git://git.kernel.dk/linux-block: (25 commits)
blkcg: annotate implicit fall through
nvme-tcp: support C2HData with SUCCESS flag
nvmet: ignore EOPNOTSUPP for discard
nvme: add proper write zeroes setup for the multipath device
nvme: add proper discard setup for the multipath device
nvme: remove nvme_ns_config_oncs
nvme: disable Write Zeroes for qemu controllers
nvmet-fc: bring Disconnect into compliance with FC-NVME spec
nvmet-fc: fix issues with targetport assoc_list list walking
nvme-fc: reject reconnect if io queue count is reduced to zero
nvme-fc: fix numa_node when dev is null
nvme-fc: use nr_phys_segments to determine existence of sgl
nvme-loop: init nvmet_ctrl fatal_err_work when allocate
nvme: update comment to make the code easier to read
nvme: put ns_head ref if namespace fails allocation
nvme-trace: fix cdw10 buffer overrun
nvme: don't warn on block content change effects
nvme: add get-feature to admin cmds tracer
md: Fix failed allocation of md_register_thread
It's wrong to add len to sector_nr in raid10 reshape twice
...
|
|
Pull KVM updates from Paolo Bonzini:
"ARM:
- some cleanups
- direct physical timer assignment
- cache sanitization for 32-bit guests
s390:
- interrupt cleanup
- introduction of the Guest Information Block
- preparation for processor subfunctions in cpu models
PPC:
- bug fixes and improvements, especially related to machine checks
and protection keys
x86:
- many, many cleanups, including removing a bunch of MMU code for
unnecessary optimizations
- AVIC fixes
Generic:
- memcg accounting"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (147 commits)
kvm: vmx: fix formatting of a comment
KVM: doc: Document the life cycle of a VM and its resources
MAINTAINERS: Add KVM selftests to existing KVM entry
Revert "KVM/MMU: Flush tlb directly in the kvm_zap_gfn_range()"
KVM: PPC: Book3S: Add count cache flush parameters to kvmppc_get_cpu_char()
KVM: PPC: Fix compilation when KVM is not enabled
KVM: Minor cleanups for kvm_main.c
KVM: s390: add debug logging for cpu model subfunctions
KVM: s390: implement subfunction processor calls
arm64: KVM: Fix architecturally invalid reset value for FPEXC32_EL2
KVM: arm/arm64: Remove unused timer variable
KVM: PPC: Book3S: Improve KVM reference counting
KVM: PPC: Book3S HV: Fix build failure without IOMMU support
Revert "KVM: Eliminate extra function calls in kvm_get_dirty_log_protect()"
x86: kvmguest: use TSC clocksource if invariant TSC is exposed
KVM: Never start grow vCPU halt_poll_ns from value below halt_poll_ns_grow_start
KVM: Expose the initial start value in grow_halt_poll_ns() as a module parameter
KVM: grow_halt_poll_ns() should never shrink vCPU halt_poll_ns
KVM: x86/mmu: Consolidate kvm_mmu_zap_all() and kvm_mmu_zap_mmio_sptes()
KVM: x86/mmu: WARN if zapping a MMIO spte results in zapping children
...
|
|
Pull IOMMU fix from Joerg Roedel:
"Fix a NULL-pointer dereference issue in the ACPI device matching code
of the AMD IOMMU driver"
* tag 'iommu-fix-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix NULL dereference bug in match_hid_uid
|
|
Pull ARM updates from Russell King:
- An improvement from Ard Biesheuvel, who noted that the identity map
setup was taking a long time due to flush_cache_louis().
- Update a comment about dma_ops from Wolfram Sang.
- Remove use of "-p" with ld, where this flag has been a no-op since
2004.
- Remove the printing of the virtual memory layout, which is no longer
useful since we hide pointers.
- Correct SCU help text.
- Remove legacy TWD registration method.
- Add pgprot_device() implementation for mapping PCI sysfs resource
files.
- Initialise PFN limits earlier for kmemleak.
- Fix argument count to match macro definition (affects clang builds)
- Use unified assembler language almost everywhere for clang, and other
clang improvements (from Stefan Agner, Nathan Chancellor).
- Support security extension for noMMU and other noMMU cleanups (from
Vladimir Murzin).
- Remove unnecessary SMP bringup code (which was incorrectly copy'n'
pasted from the ARM platform implementations) and remove it from the
arch code to discourge further copys of it appearing.
- Add Cortex A9 erratum preventing kexec working on some SoCs.
- AMBA bus identification updates from Mike Leach.
- More use of raw spinlocks to avoid -RT kernel issues (from Yang Shi
and Sebastian Andrzej Siewior).
- MCPM hyp/svc mode mismatch fixes from Marek Szyprowski.
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm: (32 commits)
ARM: 8849/1: NOMMU: Fix encodings for PMSAv8's PRBAR4/PRLAR4
ARM: 8848/1: virt: Align GIC version check with arm64 counterpart
ARM: 8847/1: pm: fix HYP/SVC mode mismatch when MCPM is used
ARM: 8845/1: use unified assembler in c files
ARM: 8844/1: use unified assembler in assembly files
ARM: 8843/1: use unified assembler in headers
ARM: 8841/1: use unified assembler in macros
ARM: 8840/1: use a raw_spinlock_t in unwind
ARM: 8839/1: kprobe: make patch_lock a raw_spinlock_t
ARM: 8837/1: coresight: etmv4: Update ID register table to add UCI support
ARM: 8836/1: drivers: amba: Update component matching to use the CoreSight UCI values.
ARM: 8838/1: drivers: amba: Updates to component identification for driver matching.
ARM: 8833/1: Ensure that NEON code always compiles with Clang
ARM: avoid Cortex-A9 livelock on tight dmb loops
ARM: smp: remove arch-provided "pen_release"
ARM: actions: remove boot_lock and pen_release
ARM: oxnas: remove CPU hotplug implementation
ARM: qcom: remove unnecessary boot_lock
ARM: 8832/1: NOMMU: Limit visibility for CONFIG_FLASH_{MEM_BASE,SIZE}
ARM: 8831/1: NOMMU: pmsa-v8: remove unneeded semicolon
...
|
|
Pull NTB updates from Jon Mason:
- fixes for switchtec debugability and mapping table entries
- NTB transport improvements
- a reworking of the peer_db_addr for better abstraction
* tag 'ntb-5.1' of git://github.com/jonmason/ntb:
NTB: add new parameter to peer_db_addr() db_bit and db_data
NTB: ntb_transport: Ensure the destination buffer is mapped for TX DMA
NTB: ntb_transport: Free MWs in ntb_transport_link_cleanup()
ntb_hw_switchtec: Added support of >=4G memory windows
ntb_hw_switchtec: NT req id mapping table register entry number should be 512
ntb_hw_switchtec: debug print 64bit aligned crosslink BAR Numbers
|
|
Pull fbdev updates from Bartlomiej Zolnierkiewicz:
"Just a couple of small fixes and cleanups:
- fix memory access if logo is bigger than the screen (Manfred
Schlaegl)
- silence fbcon logo on 'quiet' boots (Prarit Bhargava)
- use kvmalloc() for scrollback buffer in fbcon (Konstantin Khorenko)
- misc fixes (Colin Ian King, YueHaibing, Matteo Croce, Mathieu
Malaterre, Anders Roxell, Arnd Bergmann)
- misc cleanups (Rob Herring, Lubomir Rintel, Greg Kroah-Hartman,
Jani Nikula, Michal Vokáč)"
* tag 'fbdev-v5.1' of git://github.com/bzolnier/linux:
fbdev: mbx: fix a misspelled variable name
fbdev: omap2: fix warnings in dss core
video: fbdev: Fix potential NULL pointer dereference
fbcon: Silence fbcon logo on 'quiet' boots
printk: Export console_printk
ARM: dts: imx28-cfa10036: Fix the reset gpio signal polarity
video: ssd1307fb: Do not hard code active-low reset sequence
dt-bindings: display: ssd1307fb: Remove reset-active-low from examples
fbdev: fbmem: fix memory access if logo is bigger than the screen
video/fbdev: refactor video= cmdline parsing
fbdev: mbx: fix up debugfs file creation
fbdev: omap2: no need to check return value of debugfs_create functions
video: fbdev: geode: remove ifdef OLPC noise
video: offb: annotate implicit fall throughs
omapfb: fix typo
fbdev: Use of_node_name_eq for node name comparisons
fbcon: use kvmalloc() for scrollback buffer
fbdev: chipsfb: remove set but not used variable 'size'
fbdev/via: fix spelling mistake "Expandsion" -> "Expansion"
|
|
Pull i2c fixes from Wolfram Sang:
"A set of driver bugfixes and an improvement for a core helper"
* 'i2c/for-current-fixed' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: i2c-designware-platdrv: Always use a dynamic adapter number
i2c: i2c-designware-platdrv: Cleanup setting of the adapter number
i2c: add extra check to safe DMA buffer helper
i2c: i2c-stm32f7: Fix SDADEL minimum formula
i2c: rcar: explain the lockless design
i2c: rcar: fix concurrency issue related to ICDMAER
i2c: sis630: correct format strings
i2c: mediatek: modify threshold passed to i2c_get_dma_safe_msg_buf()
|
|
Pull drm fixes and updates from Dave Airlie:
"A few various fixes pulls and one late etnaviv pull but it was nearly
all fixes anyways.
etnaviv:
- late next pull
- mmu mapping fix
- build non-ARM arches
- misc fixes
i915:
- HDCP state handling fix
- shrinker interaction fix
- atomic state leak fix
qxl:
- kick out framebuffers early fix
amdgpu:
- Powerplay fixes
- DC fixes
- BACO turned off for now on vega20
- Locking fix
- KFD MQD fix
- gfx9 golden register updates"
* tag 'drm-next-2019-03-15' of git://anongit.freedesktop.org/drm/drm: (43 commits)
drm/amdgpu: Update gc golden setting for vega family
drm/amd/powerplay: correct power reading on fiji
drm/amd/powerplay: set max fan target temperature as 105C
drm/i915: Relax mmap VMA check
drm/i915: Fix atomic state leak when resetting HDMI link
drm/i915: Acquire breadcrumb ref before cancelling
drm/i915/selftests: Always free spinner on __sseu_prepare error
drm/i915: Reacquire priolist cache after dropping the engine lock
drm/i915: Protect i915_active iterators from the shrinker
drm/i915: HDCP state handling in ddi_update_pipe
drm/qxl: remove conflicting framebuffers earlier
drm/fb-helper: call vga_remove_vgacon automatically.
drm: move i915_kick_out_vgacon to vgaarb
drm/amd/display: don't call dm_pp_ function from an fpu block
drm: add __user attribute to ptr_to_compat()
drm/amdgpu: clear PDs/PTs only after initializing them
drm/amd/display: Pass app_tf by value rather than by reference
Revert "drm/amdgpu: use BACO reset on vega20 if platform support"
drm/amd/powerplay: show the right override pcie parameters
drm/amd/powerplay: honor the OD settings
...
|
|
Add a non-NULL check to fix potential NULL pointer dereference
Cleanup code to call function once.
Signed-off-by: Aaron Ma <aaron.ma@canonical.com>
Fixes: 2bf9a0a12749b ('iommu/amd: Add iommu support for ACPI HID devices')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The XEN balloon driver - in contrast to other balloon drivers - allows
to map some inflated pages to user space. Such pages are allocated via
alloc_xenballooned_pages() and freed via free_xenballooned_pages().
The pfn space of these allocated pages is used to map other things
by the hypervisor using hypercalls.
Pages marked with PG_offline must never be mapped to user space (as
this page type uses the mapcount field of struct pages).
So what we can do is, clear/set PG_offline when allocating/freeing an
inflated pages. This way, most inflated pages can be excluded by
dumping tools and the "reused for other purpose" balloon pages are
correctly not marked as PG_offline.
Fixes: 77c4adf6a6df (xen/balloon: mark inflated pages PG_offline)
Reported-by: Julien Grall <julien.grall@arm.com>
Tested-by: Julien Grall <julien.grall@arm.com>
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
|
Mika Westerberg
Aditya Pakki
Kangjie Lu
Linus Torvalds
Aaron Ma
David Hildenbrand