Age | Commit message (Collapse) | Author | Files | Lines |
|
drivers/net/ethernet/amazon/ena/ena_netdev.c: In function ena_xdp_xmit_buff:
drivers/net/ethernet/amazon/ena/ena_netdev.c:316:19: warning:
variable rx_ring set but not used [-Wunused-but-set-variable]
commit 548c4940b9f1 ("net: ena: Implement XDP_TX action")
left behind this unused variable.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need to set variable 'mbus' static
since new value always be assigned before use it.
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passing NULL to ppp_pernet causes a crash via BUG_ON.
Dereferencing net in net_generic() also has the same effect.
This patch removes the redundant BUG_ON check on the same parameter.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2019-12-27
The following pull-request contains BPF updates for your *net-next* tree.
We've added 127 non-merge commits during the last 17 day(s) which contain
a total of 110 files changed, 6901 insertions(+), 2721 deletions(-).
There are three merge conflicts. Conflicts and resolution looks as follows:
1) Merge conflict in net/bpf/test_run.c:
There was a tree-wide cleanup c593642c8be0 ("treewide: Use sizeof_field() macro")
which gets in the way with b590cb5f802d ("bpf: Switch to offsetofend in
BPF_PROG_TEST_RUN"):
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, priority) +
sizeof_field(struct __sk_buff, priority),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, priority),
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
There are a few occasions that look similar to this. Always take the chunk with
offsetofend(). Note that there is one where the fields differ in here:
<<<<<<< HEAD
if (!range_is_zero(__skb, offsetof(struct __sk_buff, tstamp) +
sizeof_field(struct __sk_buff, tstamp),
=======
if (!range_is_zero(__skb, offsetofend(struct __sk_buff, gso_segs),
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
Just take the one with offsetofend() /and/ gso_segs. Latter is correct due to
850a88cc4096 ("bpf: Expose __sk_buff wire_len/gso_segs to BPF_PROG_TEST_RUN").
2) Merge conflict in arch/riscv/net/bpf_jit_comp.c:
(I'm keeping Bjorn in Cc here for a double-check in case I got it wrong.)
<<<<<<< HEAD
if (is_13b_check(off, insn))
return -1;
emit(rv_blt(tcc, RV_REG_ZERO, off >> 1), ctx);
=======
emit_branch(BPF_JSLT, RV_REG_T1, RV_REG_ZERO, off, ctx);
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
Result should look like:
emit_branch(BPF_JSLT, tcc, RV_REG_ZERO, off, ctx);
3) Merge conflict in arch/riscv/include/asm/pgtable.h:
<<<<<<< HEAD
=======
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
#define vmemmap ((struct page *)VMEMMAP_START)
>>>>>>> 7c8dce4b166113743adad131b5a24c4acc12f92c
Only take the BPF_* defines from there and move them higher up in the
same file. Remove the rest from the chunk. The VMALLOC_* etc defines
got moved via 01f52e16b868 ("riscv: define vmemmap before pfn_to_page
calls"). Result:
[...]
#define __S101 PAGE_READ_EXEC
#define __S110 PAGE_SHARED_EXEC
#define __S111 PAGE_SHARED_EXEC
#define VMALLOC_SIZE (KERN_VIRT_SIZE >> 1)
#define VMALLOC_END (PAGE_OFFSET - 1)
#define VMALLOC_START (PAGE_OFFSET - VMALLOC_SIZE)
#define BPF_JIT_REGION_SIZE (SZ_128M)
#define BPF_JIT_REGION_START (PAGE_OFFSET - BPF_JIT_REGION_SIZE)
#define BPF_JIT_REGION_END (VMALLOC_END)
/*
* Roughly size the vmemmap space to be large enough to fit enough
* struct pages to map half the virtual address space. Then
* position vmemmap directly below the VMALLOC region.
*/
#define VMEMMAP_SHIFT \
(CONFIG_VA_BITS - PAGE_SHIFT - 1 + STRUCT_PAGE_MAX_SHIFT)
#define VMEMMAP_SIZE BIT(VMEMMAP_SHIFT)
#define VMEMMAP_END (VMALLOC_START - 1)
#define VMEMMAP_START (VMALLOC_START - VMEMMAP_SIZE)
[...]
Let me know if there are any other issues.
Anyway, the main changes are:
1) Extend bpftool to produce a struct (aka "skeleton") tailored and specific
to a provided BPF object file. This provides an alternative, simplified API
compared to standard libbpf interaction. Also, add libbpf extern variable
resolution for .kconfig section to import Kconfig data, from Andrii Nakryiko.
2) Add BPF dispatcher for XDP which is a mechanism to avoid indirect calls by
generating a branch funnel as discussed back in bpfconf'19 at LSF/MM. Also,
add various BPF riscv JIT improvements, from Björn Töpel.
3) Extend bpftool to allow matching BPF programs and maps by name,
from Paul Chaignon.
4) Support for replacing cgroup BPF programs attached with BPF_F_ALLOW_MULTI
flag for allowing updates without service interruption, from Andrey Ignatov.
5) Cleanup and simplification of ring access functions for AF_XDP with a
bonus of 0-5% performance improvement, from Magnus Karlsson.
6) Enable BPF JITs for x86-64 and arm64 by default. Also, final version of
audit support for BPF, from Daniel Borkmann and latter with Jiri Olsa.
7) Move and extend test_select_reuseport into BPF program tests under
BPF selftests, from Jakub Sitnicki.
8) Various BPF sample improvements for xdpsock for customizing parameters
to set up and benchmark AF_XDP, from Jay Jayatheerthan.
9) Improve libbpf to provide a ulimit hint on permission denied errors.
Also change XDP sample programs to attach in driver mode by default,
from Toke Høiland-Jørgensen.
10) Extend BPF test infrastructure to allow changing skb mark from tc BPF
programs, from Nikita V. Shirokov.
11) Optimize prologue code sequence in BPF arm32 JIT, from Russell King.
12) Fix xdp_redirect_cpu BPF sample to manually attach to tracepoints after
libbpf conversion, from Jesper Dangaard Brouer.
13) Minor misc improvements from various others.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Post-xmas food coma recovery fixes. Only three fixes for i915 since I
expect most people are holidaying.
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix"
* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Hold reference to intel_frontbuffer as we track activity
drm/i915/gt: Ratelimit display power w/a
drm/i915/pmu: Ensure monotonic rc6
|
|
Pull power management fixes from Rafael Wysocki:
"Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
remove redundant Kconfig dependencies from multiple devfreq drivers
(Leonard Crestez)"
* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
|
|
Pull libata fixes from Jens Axboe:
"Two things in here:
- First half of a series that fixes ahci_brcm, also marked for
stable. The other part of the series is going into 5.6 (Florian)
- sata_nv regression fix that is also marked for stable (Sascha)"
* tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block:
ata: ahci_brcm: Add missing clock management during recovery
ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE
ata: ahci_brcm: Fix AHCI resources management
ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
libata: Fix retrieving of active qcs
|
|
Pull block fixes from Jens Axboe:
"Only thing here are the changes from Arnd from last week, which now
have the appropriate header include to ensure they actually compile if
COMPAT is enabled"
* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
compat_ioctl: block: handle Persistent Reservations
compat_ioctl: block: handle add zone open, close and finish ioctl
compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
pktcdvd: fix regression on 64-bit architectures
|
|
Pull GPIO fixes from Linus Walleij:
"A set of fixes for the v5.5 series:
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which is
causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and work
properly.
- Fix the Kconfig on the Tegra driver"
* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra186: Allow building on Tegra194-only configurations
gpio: pca953x: Switch to bitops in IRQ callbacks
gpiolib: fix up emulated open drain outputs
MAINTAINERS: Append missed file to the database
gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
gpio: aspeed: avoid return type warning
gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
gpio: Fix error message on out-of-range GPIO in lookup table
gpio: mpc8xxx: Add platform device to gpiochip->parent
gpio: xtensa: fix driver build
|
|
While testing max vlan configuration on the PF, firmware gets
assert as driver was configuring number of vlans more than what
is supported per port/engine, it was figured out that there is an
implicit vlan (hidden default vlan consuming hardware cam entry resource)
which is configured default for all the clients (PF/VFs) on client_init
ramrod by the adapter implicitly, so when allocating resources among the
PFs this implicit vlan should be considered or total vlan entries should
be reduced by one to accommodate that default/implicit vlan entry.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although it has same value as MAX_MAC_CREDIT_E2,
use MAX_VLAN_CREDIT_E2 appropriately.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit f677fcb9aeb6 ("s390/qeth: ensure linear access to packet headers"),
the CQ-specific skbs are allocated with a slightly bigger linear part
than necessary. Shrink it down to the maximum that's needed by
qeth_extract_skb().
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For non-linear packets, get the skb for attaching the page fragments
from napi_get_frags() so that it can be recycled during GRO.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To reduce the path length and levels of indirection, move the RX
processing from the sub-drivers into the core.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By re-attaching RX, TX, and CTL rings during connect() rather than
assuming they are freshly allocated (i.e. assuming the counters are zero),
and avoiding forcing state to Closed in netback_remove() it is possible
for vif instances to be unbound and re-bound from and to (respectively) a
running guest.
Dynamic unbind/bind is a highly useful feature for a backend module as it
allows it to be unloaded and re-loaded (i.e. updated) without requiring
domUs to be halted.
This has been tested by running iperf as a server in the test VM and
then running a client against it in a continuous loop, whilst also
running:
while true;
do echo vif-$DOMID-$VIF >unbind;
echo down;
rmmod xen-netback;
echo unloaded;
modprobe xen-netback;
cd $(pwd);
brctl addif xenbr0 vif$DOMID.$VIF;
ip link set vif$DOMID.$VIF up;
echo up;
sleep 5;
done
in dom0 from /sys/bus/xen-backend/drivers/vif to continuously unbind,
unload, re-load, re-bind and re-plumb the backend.
Clearly a performance drop was seen but no TCP connection resets were
observed during this test and moreover a parallel SSH connection into the
guest remained perfectly usable throughout.
Signed-off-by: Paul Durrant <pdurrant@amazon.com>
Reviewed-by: Wei Liu <wei.liu@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: bee8259dd31f ("net: phy: add driver for aquantia phy")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the error path some fragments remain DMA mapped. Adding a fix
that unmaps all the fragments. Rework cleanup path to be simpler.
Fixes: 8151ee88bad5 ("dpaa_eth: use page backed rx buffers")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On RTL8211F the RX and TX delays (2ns) can be configured in two ways:
- pin strapping (RXD1 for the TX delay and RXD0 for the RX delay, LOW
means "off" and HIGH means "on") which is read during PHY reset
- using software to configure the TX and RX delay registers
So far only the configuration using pin strapping has been supported.
Add support for enabling or disabling the RGMII RX delay based on the
phy-mode to be able to get the RX delay into a known state. This is
important because the RX delay has to be coordinated between the PHY,
MAC and the PCB design (trace length). With an invalid RX delay applied
(for example if both PHY and MAC add a 2ns RX delay) Ethernet may not
work at all.
Also add debug logging when configuring the RX delay (just like the TX
delay) because this is a common source of problems.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RGMII requires a delay of 2ns between the data and the clock signal.
There are at least three ways this can happen. One possibility is by
having the PHY generate this delay.
This is a common source for problems (for example with slow TX speeds or
packet loss when sending data). The TX delay configuration of the
RTL8211F PHY can be set either by pin-strappping the RXD1 pin (HIGH
means enabled, LOW means disabled) or through configuring a paged
register. The setting from the RXD1 pin is also reflected in the
register.
Add debug logging to the TX delay configuration on RTL8211F so it's
easier to spot these issues (for example if the TX delay is enabled for
both, the RTL8211F PHY and the MAC).
This is especially helpful because there is no public datasheet for the
RTL8211F PHY available with all the RX/TX delay specifics.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As explained in previous patches, the driver no longer needs to maintain
a list of identical FIB entries (i.e, same {tb_id, prefix, prefix
length}) and therefore each FIB node can only store one FIB entry.
Remove the FIB entry list and simplify the code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After the last patch mlxsw_sp_fib{4,6}_node_entry_link() and
mlxsw_sp_fib{4,6}_node_entry_unlink() are identical and can therefore be
consolidated into the same common function.
Perform the consolidation.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Host routes that perform decapsulation of IP in IP tunnels have a
special adjacency entry linked to them. This entry stores information
such as the expected underlay source IP. When the route is deleted this
entry needs to be freed.
The allocation of the adjacency entry happens in
mlxsw_sp_fib4_entry_type_set(), but it is freed in
mlxsw_sp_fib4_node_entry_unlink().
Create a new function - mlxsw_sp_fib4_entry_type_unset() - and free the
adjacency entry there.
This will allow us to consolidate mlxsw_sp_fib{4,6}_node_entry_unlink()
in the next patch.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the driver no longer maintains a list of identical routes there is
no route to promote when a route is deleted.
Remove that code that took care of it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the networking stack takes care of only notifying the routes of
interest, we do not need to maintain a list of identical routes.
Remove the check that tests if the route is the first route in the FIB
node.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the LACP actor/partner state is now part of the uapi, rename the
3ad state defines with LACP prefix. The LACP prefix is preferred over
BOND_3AD as the LACP standard moved to 802.1AX.
Fixes: 826f66b30c2e3 ("bonding: move 802.3ad port state flags to uapi")
Signed-off-by: Andy Roulin <aroulin@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The InES at the ZHAW offers a PTP time stamping IP core. The FPGA
logic recognizes and time stamps PTP frames on the MII bus. This
patch adds a driver for the core along with a device tree binding to
allow hooking the driver to MII buses.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 1588 standard defines one step operation for both Sync and
PDelay_Resp messages. Up until now, hardware with P2P one step has
been rare, and kernel support was lacking. This patch adds support of
the mode in anticipation of new hardware developments.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When parsing a PHY node, register its time stamper, if any, and attach
the instance to the PHY device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While PHY time stamping drivers can simply attach their interface
directly to the PHY instance, stand alone drivers require support in
order to manage their services. Non-PHY MII time stamping drivers
have a control interface over another bus like I2C, SPI, UART, or via
a memory mapped peripheral. The controller device will be associated
with one or more time stamping channels, each of which sits snoops in
on a MII bus.
This patch provides a glue layer that will enable time stamping
channels to find their controlling device.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the stack supports time stamping in PHY devices. However,
there are newer, non-PHY devices that can snoop an MII bus and provide
time stamps. In order to support such devices, this patch introduces
a new interface to be used by both PHY and non-PHY devices.
In addition, the one and only user of the old PHY time stamping API is
converted to the new interface.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
An upcoming patch will change how the PHY time stamping functions are
registered with the networking stack, and adapting this driver would
entail adding forward declarations for four time stamping methods.
However, forward declarations are considered to be stylistic defects.
This patch avoids the issue by moving the probe and remove methods
immediately above the phy_driver interface structure.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netcp_ethss driver tests fields of the phy_device in order to
determine whether to defer to the PHY's time stamping functionality.
This patch replaces the open coded logic with an invocation of the
proper methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macvlan layer tests fields of the phy_device in order to determine
whether to invoke the PHY's tsinfo ethtool callback. This patch
replaces the open coded logic with an invocation of the proper
methods.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae241 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f829794 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 6bb86fefa086faba7b60bb452300b76a47cde1a5
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c40368 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c403683 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.
In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.
The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).
Fixes: 742d4d40831d ("s390/qeth: convert remaining legacy cmd callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.
Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.
Rework the code to take this lock, and drop a redundant state check in a
helper function.
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.
The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).
Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.
Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that mlxsw is converted to use the new FIB notifications it is
possible to delete the old ones and use the new replace / append /
delete notifications.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the new notifications mlxsw does not need to handle identical
routes itself, as this is taken care of by the core IPv6 code.
Instead, mlxsw only needs to take care of inserting and removing routes
from the device.
Convert mlxsw to use the new IPv6 route notifications and simplify the
code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not
call dst_confirm_neigh(), we still set it to false to keep consistency with
IPv6 code.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Simplify the code by moving the call to rtl_enable_eee() from the
individual PHY configs to rtl8169_init_phy().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|