Age | Commit message (Collapse) | Author | Files | Lines |
|
Pull ACPI fix from Rafael Wysocki:
"Prevent device references acquired by bus_find_device() in
acpi_dev_present() from being leaked (Andy Shevchenko)"
* tag 'acpi-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / utils: Drop reference in test for device presence
|
|
Pull power management fixes from Rafael Wysocki:
"These rearrange some code in the generic power domains (genpd)
framework to avoid a potential deadlock and make the turbostat utility
behave more as expected.
Specifics:
- Rearrange the generic power domains (genpd) code to avoid a
potential deadlock possible due to its interactions with the clock
framework (Jiada Wang)
- Make turbostat return the exit status of the command run under it
if that command fails (David Arcari)"
* tag 'pm-5.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / Domains: Avoid a potential deadlock
tools/power turbostat: return the exit status of a command
|
|
Pull MMC fixes from Ulf Hansson:
"A couple of MMC host fixes intended for v5.1:
- alcor: Fix DMA reads
- renesas_sdhi: Limit block count to 16-bit for old revisions
- sdhci-omap: Fixup support for read-only pins
- mxcmmc: Revert support for highmem pages
- davinci/pxamci: Fix clang build warnings"
* tag 'mmc-v5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi: limit block count to 16 bit for old revisions
mmc: alcor: fix DMA reads
mmc: sdhci-omap: Set caps2 to indicate no physical write protect pin
mmc: mxcmmc: "Revert mmc: mxcmmc: handle highmem pages"
mmc: davinci: remove extraneous __init annotation
mmc: pxamci: fix enum type confusion
|
|
After the original patch network starts to crash on heavy load.
It's not fully clear why this additional register read has such side
effects, but removing it fixes the issue.
Thanks also to Alex for his contribution and hints.
[0] https://marc.info/?t=155268170400002&r=1&w=2
Fixes: e782410ed237 ("r8169: improve spurious interrupt detection")
Reported-by: VDR User <user.vdr@gmail.com>
Tested-by: VDR User <user.vdr@gmail.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver sets a default domain id (FLPT_DEFAULT_DID) in the
first level only pasid entry, but saves a different domain id
in @sdev->did. The value saved in @sdev->did will be used to
invalidate the translation caches. Hence, the driver might
result in invalidating the caches with a wrong domain id.
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Fixes: 1c4f88b7f1f92 ("iommu/vt-d: Shared virtual address in scalable mode")
Signed-off-by: Liu Yi L <yi.l.liu@intel.com>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The spec states in 10.4.16 that the Protected Memory Enable
Register should be treated as read-only for implementations
not supporting protected memory regions (PLMR and PHMR fields
reported as Clear in the Capability register).
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Cc: mark gross <mgross@intel.com>
Suggested-by: Ashok Raj <ashok.raj@intel.com>
Fixes: f8bab73515ca5 ("intel-iommu: PMEN support")
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
If a 32 bit allocation request is too big to possibly succeed, it
early exits with a failure and then should never update max32_alloc_
size. This patch fixes current code, now the size is only updated if
the slow path failed while walking the tree. Without the fix the
allocation may enter the slow path again even if there was a failure
before of a request with the same or a smaller size.
Cc: <stable@vger.kernel.org> # 4.20+
Fixes: bee60e94a1e2 ("iommu/iova: Optimise attempts to allocate iova from 32bit address range")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Robert Richter <rrichter@marvell.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Pull drm fixes from Dave Airlie:
"i915, amdgpu, vmwgfx, exynos, nouveau and udl fixes.
Seems to be lots of little minor ones for regressions in rc1, and some
cleanups. The exynos one is the largest one, and is for a hw
difference between exynos versions"
* tag 'drm-fixes-2019-03-22' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/dmem: empty chunk do not have a buffer object associated with them.
drm/nouveau/debugfs: Fix check of pm_runtime_get_sync failure
drm/nouveau/dmem: Fix a NULL vs IS_ERR() check
drm/nouveau/dmem: remove set but not used variable 'drm'
drm/exynos/mixer: fix MIXER shadow registry synchronisation code
drm/vmwgfx: Don't double-free the mode stored in par->set_mode
drm/vmwgfx: Return 0 when gmrid::get_node runs out of ID's
drm/amdgpu: fix invalid use of change_bit
drm/amdgpu: revert "cleanup setting bulk_movable"
drm/i915: Sanity check mmap length against object size
drm/i915: Fix off-by-one in reporting hanging process
drm/i915/bios: assume eDP is present on port A when there is no VBT
drm/udl: use drm_gem_object_put_unlocked.
|
|
- Parially revert a bulk move clean up change to fix a ref count bug
- Fix invalid use of change_bit that caused a crash on PPC64 and ARM64
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321020933.3508-1-alexander.deucher@amd.com
|
|
Two fixes CC'd stable. One fix for a long-standing a bit hard-to-trigger fbdev
modesetting bug and one out-of-bo-id fix.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190321112026.114328-1-thellstrom@vmware.com
|
|
- Fix page fault issue at Mixer device
. This patch fixes the page fault issue by correcting sychronization
method for updating shadow registers for Mixer device.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Inki Dae <inki.dae@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1553162223-10090-1-git-send-email-inki.dae@samsung.com
|
|
A protection on our mmap against attempts to map past the end of the object;
plus a fix off-by-one in our hang report and a protection;
and a fix for eDP panels on Gen9 platforms on VBT absence.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190320201451.GA7993@intel.com
|
|
Some minor nouveau dmem and other fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Ben Skeggs <bskeggs@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CABDvA==kMkD6n-cS9KpQBcTU1E8p7Wc+H1ZuOhSfD7yTFJVvkw@mail.gmail.com
|
|
Empty chunk do not have a bo associated with them so no need to pin/unpin
on suspend/resume.
This fix suspend/resume on 5.1rc1 when NOUVEAU_SVM is enabled.
Signed-off-by: Jérôme Glisse <jglisse@redhat.com>
Reviewed-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Tested-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: dri-devel@lists.freedesktop.org
Cc: nouveau@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
pm_runtime_get_sync returns negative on failure.
Fixes: eaeb9010bb4b ("drm/nouveau/debugfs: Wake up GPU before doing any reclocking")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The hmm_devmem_add() function doesn't return NULL, it returns error
pointers.
Fixes: 5be73b690875 ("drm/nouveau/dmem: device memory helpers for SVM")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/nouveau/nouveau_dmem.c: In function 'nouveau_dmem_free':
drivers/gpu/drm/nouveau/nouveau_dmem.c:103:22: warning:
variable 'drm' set but not used [-Wunused-but-set-variable]
struct nouveau_drm *drm;
^
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
When there is only one byte in a frag, the current calculation
using "(size + HNS3_MAX_BD_SIZE - 1) >> HNS3_MAX_BD_SIZE_OFFSET"
will return zero, because HNS3_MAX_BD_SIZE is 65535 and
HNS3_MAX_BD_SIZE_OFFSET is 16. So it will cause tx error when
a frag's size is one byte.
This patch fixes it by using DIV_ROUND_UP.
Fixes: 3fe13ed95dd3 ("net: hns3: avoid mult + div op in critical data path")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Both PCLK and HCLK are "required" clocks according to macb devicetree
documentation. There is a chance that devm_clk_get doesn't return a
negative error but just a NULL clock structure instead. In such a case
the driver proceeds as usual and uses pclk value 0 to calculate MDC
divisor which is incorrect. Hence fix the same in clock initialization.
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the DP83825I ethernet PHY to the DP83822 driver.
These devices share the same WoL register bits and addresses.
The phy_driver init was made into a macro as there may be future
devices appended to this driver that will share the register space.
http://www.ti.com/lit/gpn/dp83825i
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix sparse warning:
drivers/irqchip/irq-mvebu-sei.c:481:23: warning:
symbol 'mvebu_sei_ap806_caps' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <jason@lakedaemon.net>
Cc: <andrew@lunn.ch>
Cc: <gregory.clement@bootlin.com>
Cc: <sebastian.hesselbarth@gmail.com>
Cc: <marc.zyngier@arm.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Link: https://lkml.kernel.org/r/20190321151448.15600-1-yuehaibing@huawei.com
|
|
Pull irqchip updates for 5.1 from Marc Zyngier:
- irqsteer error handling fix
- GICv3 range coalescing fix
- stm32 coprocessor coexistence fixes
- mbigen MSI teardown fix
- non-DT secondary GIC infrastructure removed
- various cleanups (brcmstb-l2, mmp)
- new DT bindings (r8a774c0)
|
|
mbigen_write_msg clears eventid bits of a mbigen register
when free a interrupt, because msi_domain_deactivate memset
struct msg to zero. Then multiple mbigen pins with zero eventid
will report the same interrupt number.
The eventid clear call trace:
free_irq
__free_irq
irq_shutdown
irq_domain_deactivate_irq
__irq_domain_deactivate_irq
__irq_domain_deactivate_irq
msi_domain_deactivate
platform_msi_write_msg
mbigen_write_msg
Signed-off-by: Jianguo Chen <chenjianguo3@huawei.com>
[maz: massaged subject]
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The rising configuration status register (rtsr) is not banked.
As it is shared with the co-processor, it should not be written at probe
time, else the co-processor configuration will be lost.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Falling and rising configuration and status registers are not banked.
As they are shared with M4 co-processor, they should not be cleared
at probe time, else M4 co-processor configuration will be lost.
Fixes: f9fc1745501e ("irqchip/stm32: Add host and driver data structures")
Signed-off-by: Loic Pallardy <loic.pallardy@st.com>
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Fix sparse warning:
drivers/irqchip/irq-mmp.c:182:29: warning:
symbol 'mmp_irq_domain_ops' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Fix sparse warnings:
drivers/irqchip/irq-brcmstb-l2.c:278:12: warning:
symbol 'brcmstb_l2_edge_intc_of_init' was not declared. Should it be static?
drivers/irqchip/irq-brcmstb-l2.c:285:12: warning:
symbol 'brcmstb_l2_lvl_intc_of_init' was not declared. Should it be static?
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
R-Car Gen2 has two different SDHI incarnations in the same chip. The
older one does not support the recently introduced 32 bit register
access to the block count register. Make sure we use this feature only
after the first known version.
Thanks to the Renesas Testing team for this bug report!
Fixes: 5603731a15ef ("mmc: tmio: fix access width of Block Count Register")
Reported-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Tested-by: Phong Hoang <phong.hoang.wz@renesas.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Setting max_blk_count to 1 here was causing the mmc block layer
to always use the MMC_READ_SINGLE_BLOCK command here, which the
driver does not DMA-accelerate.
Drop the max_blk_ settings here. The mmc host defaults suffice,
along with the max_segs and max_seg_size settings, which I have
now documented in more detail.
Now each MMC command reads 4 512-byte blocks, using DMA instead of
PIO. On my SD card, this increases read performance (measured with dd)
from 167kb/sec to 4.6mb/sec.
Link: http://lkml.kernel.org/r/CAD8Lp47L5T3jnAjBiPs1cQ+yFA3L6LJtgFvMETnBrY63-Zdi2g@mail.gmail.com
Signed-off-by: Daniel Drake <drake@endlessm.com>
Reviewed-by: Oleksij Rempel <linux@rempel-privat.de>
Fixes: c5413ad815a6 ("mmc: add new Alcor Micro Cardreader SD/MMC driver")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
After commit 6d5cd068ee59fba ("mmc: sdhci: use WP GPIO in
sdhci_check_ro()") and commit 39ee32ce486756f ("mmc: sdhci-omap: drop
->get_ro() implementation"), sdhci-omap relied on SDHCI_PRESENT_STATE
to check if the card is read-only, if wp-gpios is not populated
in device tree. However SDHCI_PRESENT_STATE in sdhci-omap does not have
correct read-only state.
sdhci-omap can be used by platforms with both micro SD slot and standard
SD slot with physical write protect pin (using GPIO). Set caps2 to
MMC_CAP2_NO_WRITE_PROTECT based on if wp-gpios property is populated or
not.
This fix is required since existing device-tree node doesn't have
"disable-wp" property and to preserve old-dt compatibility.
Fixes: 6d5cd068ee59fba ("mmc: sdhci: use WP GPIO in sdhci_check_ro()")
Fixes: 39ee32ce486756f ("mmc: sdhci-omap: drop ->get_ro() implementation")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit b189e7589f6d3411e85c6b7ae6eef158f08f388f.
Unable to handle kernel paging request at virtual address c8358000
pgd = efa405c3
[c8358000] *pgd=00000000
Internal error: Oops: 805 [#1] PREEMPT ARM
CPU: 0 PID: 711 Comm: kworker/0:2 Not tainted 4.20.0+ #30
Hardware name: Freescale i.MX27 (Device Tree Support)
Workqueue: events mxcmci_datawork
PC is at mxcmci_datawork+0xbc/0x2ac
LR is at mxcmci_datawork+0xac/0x2ac
pc : [<c04e33c8>] lr : [<c04e33b8>] psr: 60000013
sp : c6c93f08 ip : 24004180 fp : 00000008
r10: c8358000 r9 : c78b3e24 r8 : c6c92000
r7 : 00000000 r6 : c7bb8680 r5 : c7bb86d4 r4 : c78b3de0
r3 : 00002502 r2 : c090b2e0 r1 : 00000880 r0 : 00000000
Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment user
Control: 0005317f Table: a68a8000 DAC: 00000055
Process kworker/0:2 (pid: 711, stack limit = 0x389543bc)
Stack: (0xc6c93f08 to 0xc6c94000)
3f00: c7bb86d4 00000000 00000000 c6cbfde0 c7bb86d4 c7ee4200
3f20: 00000000 c0907ea8 00000000 c7bb86d8 c0907ea8 c012077c c6cbfde0 c7bb86d4
3f40: c6cbfde0 c6c92000 c6cbfdf4 c09280ba c0907ea8 c090b2e0 c0907ebc c0120c18
3f60: c6cbfde0 00000000 00000000 c6cbb580 c7ba7c40 c7837edc c6cbb598 00000000
3f80: c6cbfde0 c01208f8 00000000 c01254fc c7ba7c40 c0125400 00000000 00000000
3fa0: 00000000 00000000 00000000 c01010d0 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000
[<c04e33c8>] (mxcmci_datawork) from [<c012077c>] (process_one_work+0x1f0/0x338)
[<c012077c>] (process_one_work) from [<c0120c18>] (worker_thread+0x320/0x474)
[<c0120c18>] (worker_thread) from [<c01254fc>] (kthread+0xfc/0x118)
[<c01254fc>] (kthread) from [<c01010d0>] (ret_from_fork+0x14/0x24)
Exception stack(0xc6c93fb0 to 0xc6c93ff8)
3fa0: 00000000 00000000 00000000 00000000
3fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
3fe0: 00000000 00000000 00000000 00000000 00000013 00000000
Code: e3500000 1a000059 e5153050 e5933038 (e48a3004)
---[ end trace 54ca629b75f0e737 ]---
note: kworker/0:2[711] exited with preempt_count 1
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Fixes: b189e7589f6d ("mmc: mxcmmc: handle highmem pages")
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
MIXER on Exynos5 SoCs uses different synchronisation method than Exynos4
to update internal state (shadow registers).
Apparently the driver implements it incorrectly. The rule should be
as follows:
- do not request updating registers until previous request was finished,
ie. MXR_CFG_LAYER_UPDATE_COUNT must be 0.
- before setting registers synchronisation on VSYNC should be turned off,
ie. MXR_STATUS_SYNC_ENABLE should be reset,
- after finishing MXR_STATUS_SYNC_ENABLE should be set again.
The patch hopefully implements it correctly.
Below sample kernel log from page fault caused by the bug:
[ 25.670038] exynos-sysmmu 14650000.sysmmu: 14450000.mixer: PAGE FAULT occurred at 0x2247b800
[ 25.677888] ------------[ cut here ]------------
[ 25.682164] kernel BUG at ../drivers/iommu/exynos-iommu.c:450!
[ 25.687971] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 25.693778] Modules linked in:
[ 25.696816] CPU: 5 PID: 1553 Comm: fb-release_test Not tainted 5.0.0-rc7-01157-g5f86b1566bdd #136
[ 25.705646] Hardware name: SAMSUNG EXYNOS (Flattened Device Tree)
[ 25.711710] PC is at exynos_sysmmu_irq+0x1c0/0x264
[ 25.716470] LR is at lock_is_held_type+0x44/0x64
v2: added missing MXR_CFG_LAYER_UPDATE bit setting in mixer_enable_sync
Reported-by: Marian Mihailescu <mihailescu2m@gmail.com>
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The event pool used for queueing commands is destroyed fairly early in the
ibmvscsi_remove() code path. Since, this happens prior to the call so
scsi_remove_host() it is possible for further calls to queuecommand to be
processed which manifest as a panic due to a NULL pointer dereference as
seen here:
PANIC: "Unable to handle kernel paging request for data at address
0x00000000"
Context process backtrace:
DSISR: 0000000042000000 ????Syscall Result: 0000000000000000
4 [c000000002cb3820] memcpy_power7 at c000000000064204
[Link Register] [c000000002cb3820] ibmvscsi_send_srp_event at d000000003ed14a4
5 [c000000002cb3920] ibmvscsi_send_srp_event at d000000003ed14a4 [ibmvscsi] ?(unreliable)
6 [c000000002cb39c0] ibmvscsi_queuecommand at d000000003ed2388 [ibmvscsi]
7 [c000000002cb3a70] scsi_dispatch_cmd at d00000000395c2d8 [scsi_mod]
8 [c000000002cb3af0] scsi_request_fn at d00000000395ef88 [scsi_mod]
9 [c000000002cb3be0] __blk_run_queue at c000000000429860
10 [c000000002cb3c10] blk_delay_work at c00000000042a0ec
11 [c000000002cb3c40] process_one_work at c0000000000dac30
12 [c000000002cb3cd0] worker_thread at c0000000000db110
13 [c000000002cb3d80] kthread at c0000000000e3378
14 [c000000002cb3e30] ret_from_kernel_thread at c00000000000982c
The kernel buffer log is overfilled with this log:
[11261.952732] ibmvscsi: found no event struct in pool!
This patch reorders the operations during host teardown. Start by calling
the SRP transport and Scsi_Host remove functions to flush any outstanding
work and set the host offline. LLDD teardown follows including destruction
of the event pool, freeing the Command Response Queue (CRQ), and unmapping
any persistent buffers. The event pool destruction is protected by the
scsi_host lock, and the pool is purged prior of any requests for which we
never received a response. Finally, move the removal of the scsi host from
our global list to the end so that the host is easily locatable for
debugging purposes during teardown.
Cc: <stable@vger.kernel.org> # v2.6.12+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For each ibmvscsi host created during a probe or destroyed during a remove
we either add or remove that host to/from the global ibmvscsi_head
list. This runs the risk of concurrent modification.
This patch adds a simple spinlock around the list modification calls to
prevent concurrent updates as is done similarly in the ibmvfc driver and
ipr driver.
Fixes: 32d6e4b6e4ea ("scsi: ibmvscsi: add vscsi hosts to global list_head")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Make sure we don't try to enqueue XDP_REDIRECT frames to an
inexistent FQ.
While it is guaranteed not to have more than one queue per core,
having fewer queues than CPUs on an interface is a valid
configuration.
Fixes: d678be1dc1ec ("dpaa2-eth: add XDP_REDIRECT support")
Reported-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip is sold either with an SPI interface (KSZ8851SNL) or
with a so-called non-PCI interface (KSZ8851-16MLL). When the driver
for the latter was introduced with commit a55c0a0ed415 ("drivers/net:
ks8851_mll ethernet network driver"), it duplicated the register macros
introduced by the driver for the former with commit 3ba81f3ece3c ("net:
Micrel KS8851 SPI network driver").
The chips are almost identical, so the duplication seems unwarranted.
There are a handful of bits which are in use on the KSZ8851-16MLL but
reserved on the KSZ8851SNL, and vice-versa, but there are no actual
collisions.
Thus, remove the duplicate definitions from the KSZ8851-16MLL driver.
Mark all bits which differ between the two chips. Move the SPI frame
opcodes, which are specific to KSZ8851SNL, to its driver.
The KSZ8851-16MLL driver added a RXFCTR_THRESHOLD_MASK macro which is a
duplication of the RXFCTR_RXFCT_MASK macro, rename it where it's used.
Same for P1MBCR_FORCE_FDX, which duplicates the BMCR_FULLDPLX macro and
OBCR_ODS_16MA, which duplicates OBCR_ODS_16mA.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the header file accompanying the ks8851 driver, the P1SCLMD register
macros are misnamed, they actually pertain to the P1CR register.
The P1CR macros in turn pertain to the P1SR register, see pages 65 to 68
of the spec:
http://www.hqchip.com/uploads/pdf/201703/47c98946d6c97a4766e14db3f24955f2.pdf
The misnomers have no negative consequences so far because the macros
aren't used by ks8851.c, but that's about to change.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 chip's initial carrier state is down. A Link Change Interrupt
is signaled once interrupts are enabled if the carrier is up.
The ks8851 driver has it backwards by assuming that the initial carrier
state is up. The state is therefore misrepresented if the interface is
opened with no cable attached. Fix it.
The Link Change interrupt is sometimes not signaled unless the P1MBSR
register (which contains the Link Status bit) is read on ->ndo_open().
This might be a hardware erratum. Read the register by calling
mii_check_link(), which has the desirable side effect of setting the
carrier state to down if the cable was detached while the interface was
closed.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver currently requests the IRQ before registering the
net_device. Because the net_device name is used as IRQ name and is
still "eth%d" when the IRQ is requested, it's impossibe to tell IRQs
apart if multiple ks8851 chips are present. Most other drivers delay
requesting the IRQ until the net_device is opened. Do the same.
The driver doesn't enable interrupts on the chip before opening the
net_device and disables them when closing it, so there doesn't seem to
be a need to request the IRQ already on probe.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 73fdeb82e963 ("net: ks8851: Add optional vdd_io regulator and
reset gpio") amended the ks8851 driver to briefly assert the chip's
reset pin on probe. It also amended the probe routine's error path to
reassert the reset pin if a subsequent initialization step fails.
However the commit misplaced reassertion of the reset pin in the error
path such that it is not performed if the check of the Chip ID and
Enable Register (CIDER) fails. The error path is therefore slightly
asymmetrical to the probe routine's body. Fix it.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ks8851 driver lets the chip auto-dequeue received packets once they
have been read in full. It achieves that by setting the ADRFE flag in
the RXQCR register ("Auto-Dequeue RXQ Frame Enable").
However if allocation of a packet's socket buffer or retrieval of the
packet over the SPI bus fails, the packet will not have been read in
full and is not auto-dequeued. Such partial retrieval of a packet
confuses the chip's RX queue management: On the next RX interrupt,
the first packet read from the queue will be the one left there
previously and this one can be retrieved without issues. But for any
newly received packets, the frame header status and byte count registers
(RXFHSR and RXFHBCR) contain bogus values, preventing their retrieval.
The chip allows explicitly dequeueing a packet from the RX queue by
setting the RRXEF flag in the RXQCR register ("Release RX Error Frame").
This could be used to dequeue the packet in case of an error, but if
that error is a failed SPI transfer, it is unknown if the packet was
transferred in full and was auto-dequeued or if it was only transferred
in part and requires an explicit dequeue. The safest approach is thus
to always dequeue packets explicitly and forgo auto-dequeueing.
Without this change, I've witnessed packet retrieval break completely
when an SPI DMA transfer fails, requiring a chip reset. Explicit
dequeueing magically fixes this and makes packet retrieval absolutely
robust for me.
The chip's documentation suggests auto-dequeuing and uses the RRXEF
flag only to dequeue error frames which the driver doesn't want to
retrieve. But that seems to be a fair-weather approach.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We found out that for v2 hw, a SATA disk can not be written to after the
system comes up.
In commit ffb1c820b8b6 ("scsi: hisi_sas: remove the check of sas_dev status
in hisi_sas_I_T_nexus_reset()"), we introduced a path where we may issue an
internal abort for a SATA device, but without following it with a
softreset.
We need to always follow an internal abort with a software reset, as per HW
programming flow, so add this.
Fixes: ffb1c820b8b6 ("scsi: hisi_sas: remove the check of sas_dev status in hisi_sas_I_T_nexus_reset()")
Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The lpi_range_list is supposed to be sorted in ascending order of
->base_id (at least if the range merging is to work), but the current
comparison function returns a positive value if rb->base_id >
ra->base_id, which means that list_sort() will put A after B in that
case - and vice versa, of course.
Fixes: 880cb3cddd16 (irqchip/gic-v3-its: Refactor LPI allocator)
Cc: stable@vger.kernel.org (v4.19+)
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
|
|
When calling vmw_fb_set_par(), the mode stored in par->set_mode gets free'd
twice. The first free is in vmw_fb_kms_detach(), the second is near the
end of vmw_fb_set_par() under the name of 'old_mode'. The mode-setting code
only works correctly if the mode doesn't actually change. Removing
'old_mode' in favor of using par->set_mode directly fixes the problem.
Cc: <stable@vger.kernel.org>
Fixes: a278724aa23c ("drm/vmwgfx: Implement fbdev on kms v2")
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Deepak Rawat <drawat@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
If it's not a system error and get_node implementation accommodate the
buffer object then it should return 0 with memm::mm_node set to NULL.
v2: Test for id != -ENOMEM instead of id == -ENOSPC.
Cc: <stable@vger.kernel.org>
Fixes: 4eb085e42fde ("drm/vmwgfx: Convert to new IDA API")
Signed-off-by: Deepak Rawat <drawat@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
|
|
clang points out a harmless signed integer overflow:
drivers/net/ethernet/3com/3c515.c:1530:66: error: implicit conversion from 'int' to 'short' changes value from 32783 to -32753 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast | RxProm;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~
drivers/net/ethernet/3com/3c515.c:1532:52: error: implicit conversion from 'int' to 'short' changes value from 32775 to -32761 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxMulticast | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
drivers/net/ethernet/3com/3c515.c:1534:38: error: implicit conversion from 'int' to 'short' changes value from 32773 to -32763 [-Werror,-Wconstant-conversion]
new_mode = SetRxFilter | RxStation | RxBroadcast;
~ ~~~~~~~~~~~~~~~~~~~~~~~~^~~~~~~~~~~~~
Make the variable unsigned to avoid the overflow.
Fixes: Linux-2.1.128pre1
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lockdep warns that prepare_lock and genpd->mlock can cause a deadlock
the deadlock scenario is like following:
First thread is probing cs2000
cs2000_probe()
clk_register()
__clk_core_init()
clk_prepare_lock() ----> acquires prepare_lock
cs2000_recalc_rate()
i2c_smbus_read_byte_data()
rcar_i2c_master_xfer()
dma_request_chan()
rcar_dmac_of_xlate()
rcar_dmac_alloc_chan_resources()
pm_runtime_get_sync()
__pm_runtime_resume()
rpm_resume()
rpm_callback()
genpd_runtime_resume() ----> acquires genpd->mlock
Second thread is attaching any device to the same PM domain
genpd_add_device()
genpd_lock() ----> acquires genpd->mlock
cpg_mssr_attach_dev()
of_clk_get_from_provider()
__of_clk_get_from_provider()
__clk_create_clk()
clk_prepare_lock() ----> acquires prepare_lock
Since currently no PM provider access genpd's critical section
in .attach_dev, and .detach_dev callbacks, so there is no need to protect
these two callbacks with genpd->mlock.
This patch avoids a potential deadlock by moving out .attach_dev and .detach_dev
from genpd->mlock, so that genpd->mlock won't be held when prepare_lock is acquired
in .attach_dev and .detach_dev
Signed-off-by: Jiada Wang <jiada_wang@mentor.com>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When commit 8661423eea1a ("ACPI / utils: Add new acpi_dev_present
helper") introduced acpi_dev_present(), it missed the fact that
bus_find_device() took a reference on the device found by it and
the callers of acpi_dev_present() don't drop that reference.
Drop the reference on the device in acpi_dev_present().
Fixes: 8661423eea1a ("ACPI / utils: Add new acpi_dev_present helper")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When using 16K DMA buffers and ring mode, the DES3 refill is not working
correctly as the function is using a bogus pointer for checking the
private data. As a result stale pointers will remain in the RX descriptor
ring, so DMA will now likely overwrite/corrupt some already freed memory.
As simple reproducer, just receive some UDP traffic:
# ifconfig eth0 down; ifconfig eth0 mtu 9000; ifconfig eth0 up
# iperf3 -c 192.168.253.40 -u -b 0 -R
If you didn't crash by now check the RX descriptors to find non-contiguous
RX buffers:
cat /sys/kernel/debug/stmmaceth/eth0/descriptors_status
[...]
1 [0x2be5020]: 0xa3220321 0x9ffc1ffc 0x72d70082 0x130e207e
^^^^^^^^^^^^^^^^^^^^^
2 [0x2be5040]: 0xa3220321 0x9ffc1ffc 0x72998082 0x1311a07e
^^^^^^^^^^^^^^^^^^^^^
A simple ping test will now report bad data:
# ping -s 8200 192.168.253.40
PING 192.168.253.40 (192.168.253.40) 8200(8228) bytes of data.
8208 bytes from 192.168.253.40: icmp_seq=1 ttl=64 time=1.00 ms
wrong data byte #8144 should be 0xd0 but was 0x88
Fix the wrong pointer. Also we must refill DES3 only if the DMA buffer
size is 16K.
Fixes: 54139cf3bb33 ("net: stmmac: adding multiple buffers for rx")
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Acked-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|