| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
First set of patches for 4.21. Most notable here is support for
Quantenna's QSR1000/QSR2000 chipsets and more flexible ways to provide
nvram files for brcmfmac.
Major changes:
brcmfmac
* add support for first trying to get a board specific nvram file
* add support for getting nvram contents from EFI variables
qtnfmac
* use single PCIe driver for all platforms and rename
Kconfig option CONFIG_QTNFMAC_PEARL_PCIE to CONFIG_QTNFMAC_PCIE
* add support for QSR1000/QSR2000 (Topaz) family of chipsets
ath10k
* add support for WCN3990 firmware crash recovery
* add firmware memory dump support for QCA4019
wil6210
* add firmware error recovery while in AP mode
ath9k
* remove experimental notice from dynack feature
iwlwifi
* PCI IDs for some new 9000-series cards
* improve antenna usage on connection problems
* new firmware debugging infrastructure
* some more work on 802.11ax
* improve support for multiple RF modules with 22000 devices
cordic
* move cordic macros and defines to a public header file
* convert brcmsmac and b43 to fully use cordic library
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All DaVinci boards still supported in board files now define nvmem
cells containing the MAC address. We want to stop using the setup
callback from at24 so the MAC address for those users will no longer
be provided over platform data. If we didn't get a valid MAC in pdata,
try nvmem before resorting to a random MAC.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We've switched all users to nvmem_get_mac_address(). Remove the now
dead code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We now have a generalized helper routine to read the MAC address from
nvmem which takes struct device as argument. The nvmem subsystem will
then try device tree first before all other potential providers.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support to dump PF PCIe registers using ethtool -d
for HNS3 PF Driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds "ethtool -d" support for HNS3 VF Driver.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So far the two functions consider neither member eee_enabled nor
eee_active. Therefore network drivers have to do this in some kind
of glue code. I think this can be avoided.
Getting EEE parameters:
When not advertising any EEE mode, we can't consider EEE to be enabled.
Therefore interpret "EEE enabled" as "we advertise at least one EEE
mode". It's similar with "EEE active": interpret it as "EEE modes
advertised by both link partner have at least one mode in common".
Setting EEE parameters:
If eee_enabled isn't set, don't advertise any EEE mode and restart
aneg if needed to switch off EEE. If eee_enabled is set and
data->advertised is empty (e.g. because EEE was disabled), advertise
everything we support as default. This way EEE can easily switched
on/off by doing ethtool --set-eee <if> eee on/off, w/o any additional
parameters.
The changes to both functions shouldn't break any existing user.
Once the changes have been applied, at least some users can be
simplified.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Creating a VXLAN device with is underlay in the non-default VRF makes
egress route lookup fail or incorrect since it will resolve in the
default VRF, and ingress fail because the socket listens in the default
VRF.
This patch binds the underlying UDP tunnel socket to the l3mdev of the
lower device of the VXLAN device. This will listen in the proper VRF and
output traffic from said l3mdev, matching l3mdev routing rules and
looking up the correct routing table.
When the VXLAN device does not have a lower device, or the lower device
is in the default VRF, the socket will not be bound to any interface,
keeping the previous behaviour.
The underlay l3mdev is deduced from the VXLAN lower device
(IFLA_VXLAN_LINK).
+----------+ +---------+
| | | |
| vrf-blue | | vrf-red |
| | | |
+----+-----+ +----+----+
| |
| |
+----+-----+ +----+----+
| | | |
| br-blue | | br-red |
| | | |
+----+-----+ +---+-+---+
| | |
| +-----+ +-----+
| | |
+----+-----+ +------+----+ +----+----+
| | lower device | | | |
| eth0 | <- - - - - - - | vxlan-red | | tap-red | (... more taps)
| | | | | |
+----------+ +-----------+ +---------+
Signed-off-by: Alexis Bauvin <abauvin@scaleway.com>
Reviewed-by: Amine Kherbouche <akherbouche@scaleway.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Tested-by: Amine Kherbouche <akherbouche@scaleway.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Load firmware version based on 'fw_load_policy' devlink parameter. The
driver supports these two options:
* DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_DRIVER (0)
Default, load firmware version preferred by the driver
* DEVLINK_PARAM_FW_LOAD_POLICY_VALUE_FLASH (1)
Load firmware currently stored in flash
The second option, 'flash', allow the device to run with different firmware
version than preferred by the driver for testing and/or debugging purposes.
For example, testing a firmware bug fix.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After flashing new firmware during the driver initialization flow (reload
or not), the driver should do a firmware reset when it gets -EAGAIN in
order to load the new one.
Signed-off-by: Shalom Toledo <shalomt@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns:
drivers/net/usb/aqc111.c:1326:37: warning: suggest braces around
initialization of subobject [-Wmissing-braces]
struct aqc111_wol_cfg wol_cfg = { 0 };
^
{}
1 warning generated.
Use memset to initialize the object to take compiler instrumentation out
of the equation.
Fixes: e58ba4544c77 ("net: usb: aqc111: Add support for wake on LAN by MAGIC packet")
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c: In function 'rmnet_map_do_flow_control':
drivers/net/ethernet/qualcomm/rmnet/rmnet_map_command.c:23:36: warning:
variable 'cmd' set but not used [-Wunused-but-set-variable]
struct rmnet_map_control_command *cmd;
'cmd' not used anymore now, should also be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The userspace may need to control the carrier state.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Didier Pallard <didier.pallard@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 1c30d1836aeb ("mlxsw: spectrum: Enable VxLAN enslavement to
bridges") enabled the enslavement of VxLAN devices to bridges that have
mlxsw ports (or their upper) as slaves. This patch extends mlxsw to also
support VLAN-aware bridges.
The patch is similar in nature to mentioned commit, but there is one
major difference. With VLAN-aware bridges, the VxLAN device's VNI is
mapped to the VLAN that is configured as PVID and egress untagged on the
bridge port.
Therefore, the driver is extended to listen to VLAN configuration on
VxLAN devices of interest and enable / disable NVE encapsulation on the
corresponding 802.1Q FIDs.
To prevent ambiguity, the driver makes sure that a given VLAN is not
configured as PVID and egress untagged on multiple VxLAN devices. This
sanitization takes place both when a port is enslaved to a bridge with
existing VxLAN devices and when a VLAN is added to / removed from a
VxLAN device of interest.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vxlan_join() function resolves the FID on which the VNI should be
set and then sets the VNI. Currently, the FID is simply resolved
according to the ifindex of the bridge device to which the VxLAN device
is enslaved. This works because only VLAN-unaware bridges are supported.
With VLAN-aware bridges the FID would need to be resolved based on the
VLAN to which the VNI is mapped to.
Add the VLAN ID to the argument list of the function.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function mlxsw_sp_bridge_vxlan_leave() is currently split between
VLAN-aware and VLAN-unaware bridges, but actually both types can use the
same function.
The function needs to resolve the FID that corresponds to the VxLAN
device and disable NVE encapsulation on it. Instead of looking up the
FID differently for VLAN-aware and VLAN-unaware bridges, we can always
use the VxLAN's device VNI.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In a similar fashion to commit 564c6d727aca ("mlxsw: spectrum_fid: Add
APIs to lookup FID without creating it"), add a corresponding API to
lookup 802.1Q FIDs.
This is a prerequisite to VxLAN support with VLAN-aware bridges and will
allow us to resolve a 802.1Q FID by its VLAN when an FDB entry is added
on the bridge port of the VxLAN device.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All L2 queues funnel through this flow, so this would cover the
regular RSS queues, as well queues created for VFs, mqos queues,
xdp queues, etc.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the doorbelling entities are outside of the core module.
L2 queues, Roce queues, iscsi and fcoe all need to register.
Make the APIs available for these drivers.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Light L2 queues are doorbelling entities. Modify the implementation
to keep the doorbell data necessary for doorbelling in well known
location instead of recomputing every time. Register the LL2 queue
with doorbell recovery mechanism.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Slow path queue is a doorbelling entity. Register it with the overflow mechanism.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of an attention from the doorbell queue block, analyze the HW
indications. In case of a doorbell overflow, execute a doorbell recovery.
Since there can be spurious indications (race conditions between multiple PFs),
schedule a periodic task for checking whether a doorbell overflow may have been
missed. After a set time with no indications, terminate the periodic task.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the database used to register doorbelling entities, and APIs for adding
and deleting entries, and logic for traversing the database and doorbelling
once on behalf of all entities.
Signed-off-by: Ariel Elior <Ariel.Elior@cavium.com>
Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com>
Signed-off-by: Tomer Tayar <Tomer.Tayar@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW reconfiguration timeouts are a common indicator of FW trouble.
To make debugging easier print requested update and control word
when reconfiguration fails.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When troubleshooting incorrect FW capabilities it's useful to know
where the faulty TLV is located. Add offset to all errors messages.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW/HW can generally support the standard networking offloads
on representors without any trouble. Add the ability for FW
to advertise which features should be available on representors.
Because representors are muxed on top of the vNIC we need to listen
on feature changes of their lower devices, and update their features
appropriately.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we never needed to keep a networking locks around
representors accesses, we only accessed them when device was
reconfigured (under nfp pf->lock) or on fast path (under RCU).
Now we want to be able to iterate over all representors during
notifications, so make sure representor assignment is done
under RTNL lock.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our representors are software devices built on top of the PF
vNIC, the queuing should only happen at the vNIC netdevice.
Allow representors to run qdisc-less.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our representors are software devices built on top of the PF
vNIC, the only state they have are per-cpu stats, so make
the TX run locklessly.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: John Hurley <john.hurley@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for TSO over representors make sure the port id
prepend will always fit in the frame. The current max header
length is 255, which is ample, so assume worst case scenario
of 8 byte prepend and save ourselves the conditionals.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSO-related offsets in the descriptor should not include
the length of the prepended metadata. Adjust them. Note that
this could not have caused issues in the past as we don't
support TSO with metadata prepend as of this patch.
Signed-off-by: Michael Rapson <michael.rapson@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
nd_q is only used at the very end of nfp_net_tx(), there is no need
to initialize it early.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move temporary variables in scope of the loop in nfp_net_tx_complete(),
and add a temp for txbuf software structure. This saves us 0.2% of CPU.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Chained descriptors for fragments need to duplicate all the descriptor
fields of the skb head, so we copy the descriptor and then modify the
relevant fields. This is wasteful, because the top half of the descriptor
will get overwritten entirely while the bottom half is not modified at all.
Copy only the bottom half. This saves us 0.3% of CPU in a GSO test.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Total number of VFs supported by PF is used to determine the last
byte of VF's mac address. Number of VFs supported is not always
16, use the variable nvfs to get the number of VFs supported
rather than hard coding it to 16.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Reported-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
skb_linearization can fail due to memory allocation failure.
In such a case, the driver will drop the packet. In such a case
The driver used to print an error message.
This patch replaces this error message by a dedicated statistic.
Signed-off-by: Michael Shteinbok <michael.shteinbok@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add comments in the switch statement for XDP action to indicate
fallthrough is intended.
Signed-off-by: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since the wol state forces to be initialized after reset, the state should
be preserved in suspend/resume sequence.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If wol state of phy hardware is enabled after reset, phy_ethtool_get_wol()
returns that wol.wolopts is true.
However, since net_device.wol_enabled is zero and this doesn't apply wol
state until calling ethtool_set_wol(), so mdio_bus_phy_may_suspend()
returns true, that is, it's in a state where phy can suspend even though
wol state is enabled.
In this inconsistency, phy_suspend() returns -EBUSY, and at last,
suspend sequence fails with the following message:
dpm_run_callback(): mdio_bus_phy_suspend+0x0/0x58 returns -16
PM: Device 65000000.ethernet-ffffffff:01 failed to suspend: error -16
PM: Some devices failed to suspend, or early wake event detected
In order to fix the above issue, this patch forces to set initial wol state
to disabled as default.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch introduces suspend and resume functions to ave driver.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I ended up tracking down some rather nasty issues with f2fs (and other
filesystem modules) constantly crashing on my kernel down to a
combination of out of bounds memory accesses, one of which was coming
from brcmfmac during module load:
[ 30.891382] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4356-sdio for chip BCM4356/2
[ 30.894437] ==================================================================
[ 30.901581] BUG: KASAN: global-out-of-bounds in brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.909935] Read of size 1 at addr ffff2000024865df by task kworker/6:2/387
[ 30.916805]
[ 30.918261] CPU: 6 PID: 387 Comm: kworker/6:2 Tainted: G O 4.20.0-rc3Lyude-Test+ #19
[ 30.927251] Hardware name: amlogic khadas-vim2/khadas-vim2, BIOS 2018.07-rc2-armbian 09/11/2018
[ 30.935964] Workqueue: events brcmf_driver_register [brcmfmac]
[ 30.941641] Call trace:
[ 30.944058] dump_backtrace+0x0/0x3e8
[ 30.947676] show_stack+0x14/0x20
[ 30.950968] dump_stack+0x130/0x1c4
[ 30.954406] print_address_description+0x60/0x25c
[ 30.959066] kasan_report+0x1b4/0x368
[ 30.962683] __asan_report_load1_noabort+0x18/0x20
[ 30.967547] brcmf_fw_alloc_request+0x42c/0x480 [brcmfmac]
[ 30.967639] brcmf_sdio_probe+0x163c/0x2050 [brcmfmac]
[ 30.978035] brcmf_ops_sdio_probe+0x598/0xa08 [brcmfmac]
[ 30.983254] sdio_bus_probe+0x190/0x398
[ 30.983270] really_probe+0x2a0/0xa70
[ 30.983296] driver_probe_device+0x1b4/0x2d8
[ 30.994901] __driver_attach+0x200/0x280
[ 30.994914] bus_for_each_dev+0x10c/0x1a8
[ 30.994925] driver_attach+0x38/0x50
[ 30.994935] bus_add_driver+0x330/0x608
[ 30.994953] driver_register+0x140/0x388
[ 31.013965] sdio_register_driver+0x74/0xa0
[ 31.014076] brcmf_sdio_register+0x14/0x60 [brcmfmac]
[ 31.023177] brcmf_driver_register+0xc/0x18 [brcmfmac]
[ 31.023209] process_one_work+0x654/0x1080
[ 31.032266] worker_thread+0x4f0/0x1308
[ 31.032286] kthread+0x2a8/0x320
[ 31.039254] ret_from_fork+0x10/0x1c
[ 31.039269]
[ 31.044226] The buggy address belongs to the variable:
[ 31.044351] brcmf_firmware_path+0x11f/0xfffffffffffd3b40 [brcmfmac]
[ 31.055601]
[ 31.057031] Memory state around the buggy address:
[ 31.061800] ffff200002486480: 04 fa fa fa fa fa fa fa 00 00 00 00 00 00 00 00
[ 31.068983] ffff200002486500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.068993] >ffff200002486580: 00 00 00 00 00 00 00 00 fa fa fa fa 00 00 00 00
[ 31.068999] ^
[ 31.069017] ffff200002486600: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 31.096521] ffff200002486680: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
[ 31.096528] ==================================================================
[ 31.096533] Disabling lock debugging due to kernel taint
It appears that when trying to determine the length of the string in the
alternate firmware path, we make the mistake of not handling the case
where the firmware path is empty correctly. Since strlen(mp_path) can
return 0, we'll end up accessing mp_path[-1] when the firmware_path
isn't provided through the module arguments.
So, fix this by just setting the end char to '\0' by default, and only
changing it if we have a non-zero length. Additionally, use strnlen()
with BRCMF_FW_ALTPATH_LEN instead of strlen() just to be extra safe.
Fixes: 2baa3aaee27f ("brcmfmac: introduce brcmf_fw_alloc_request() function")
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Arend van Spriel <arend.vanspriel@broadcom.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Arend Van Spriel <arend.vanspriel@broadcom.com>
Cc: Himanshu Jha <himanshujha199640@gmail.com>
Cc: Dan Haab <dhaab@luxul.com>
Cc: Jia-Shyr Chuang <saint.chuang@cypress.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: <stable@vger.kernel.org> # v4.17+
Signed-off-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ARM systems with UEFI may have both devicetree (of) and DMI data in this
case we end up setting brcmf_mp_device.board_type twice.
In this case we should prefer the devicetree data, because:
1) The devicerree data is more reliable
2) Some ARM systems (e.g. the Raspberry Pi 3 models) support both UEFI and
classic uboot booting, the devicetree data is always there, so using it
makes sure we ask for the same nvram file independent of how we booted.
This commit moves the brcmf_dmi_probe call to before the brcmf_of_probe
call, so that the latter can override the value of the first if both are
set.
Fixes: bd1e82bb420a ("brcmfmac: Set board_type from DMI on x86 based ...")
Cc: Peter Robinson <pbrobinson@gmail.com>
Tested-and-reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The newest firmwares provide STA info using v7 of the struct. As v7
isn't backward compatible, a union is needed.
Even though brcmfmac does not use any of the new info it's important to
provide the proper struct buffer. Without this change new firmwares will
fallback to the very limited v3 instead of something in between such as
v4.
Signed-off-by: Dan Haab <dan.haab@luxul.com>
Reviewed-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Kernel library has a common cordic algorithm which is identical
to internally implemented one, so use it and drop the duplicate
implementation.
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The cordic routine for calculating sines and cosines that was added in
commit 6f98e62a9f1b ("b43: update cordic code to match current specs")
contains an error whereby a quantity declared u32 can in fact go negative.
This problem was detected by Priit Laes who is switching b43 to use the
routine in the library functions of the kernel.
Fixes: 986504540306 ("b43: make cordic common (LP-PHY and N-PHY need it)")
Reported-by: Priit Laes <plaes@plaes.org>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Stable <stable@vger.kernel.org> # 2.6.34
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Current driver includes macro that is available from general cordic
library. Use that and drop unused duplicate and unneeded internal
definitions.
Signed-off-by: Priit Laes <plaes@plaes.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Marc Kleine-Budde says:
====================
This is a pull request for net-next/master consisting of 18 patches.
The first patch is by Colin Ian King and fixes the spelling in the ucan
driver.
The next three patches target the xilinx driver. YueHaibing's patch
fixes the return type of ndo_start_xmit function. Two patches by
Shubhrajyoti Datta add support for the CAN FD 2.0 controllers.
Flavio Suligoi's patch for the sja1000 driver add support for the ASEM
CAN raw hardware.
Wolfram Sang's and Kuninori Morimoto's patches switch the rcar driver to
use SPDX license identifiers.
The remaining 111 patches improve the flexcan driver. Pankaj Bansal's
patch enables the driver in Kconfig on all architectures with IOMEM
support. The next four patches by me fix indention, add missing
parentheses and comments. Aisheng Dong's patches add self wake support
and document it in the DT bindings. The remaining patches by Pankaj
Bansal first fix the loopback support and prepare the driver for the
CAN-FD support needed for the LX2160A SoC. The actual CAN-FD support
will be added in a later patch series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial conflict in net/core/filter.c, a locally computed
'sdif' is now an argument to the function.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
David S. Miller
Bartosz Golaszewski
Jian Shen
Heiner Kallweit
Alexis Bauvin
Shalom Toledo
Nathan Chancellor
YueHaibing
Nicolas Dichtel
Ido Schimmel
Ariel Elior
Jakub Kicinski
Ganesh Goudar
Michael Shteinbok
Ioana Ciocoi Radulescu
Kunihiko Hayashi
Lyude Paul
Hans de Goede
Dan Haab
Priit Laes
Larry Finger