aboutsummaryrefslogtreecommitdiffstats
path: root/drivers (follow)
AgeCommit message (Collapse)AuthorFilesLines
2020-02-20bnxt_en: Improve device shutdown method.Vasundhara Volam1-2/+2
Especially when bnxt_shutdown() is called during kexec, we need to disable MSIX and disable Bus Master to completely quiesce the device. Make these 2 calls unconditionally in the shutdown method. Fixes: c20dc142dd7b ("bnxt_en: Disable bus master during PCI shutdown and driver unload.") Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by: Michael Chan <michael.chan@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20net: thunderx: workaround BGX TX Underflow issueTim Harvey2-3/+68
While it is not yet understood why a TX underflow can easily occur for SGMII interfaces resulting in a TX wedge. It has been found that disabling/re-enabling the LMAC resolves the issue. Signed-off-by: Tim Harvey <tharvey@gateworks.com> Reviewed-by: Robert Jones <rjones@gateworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20ionic: fix fw_status readShannon Nelson2-4/+8
The fw_status field is only 8 bits, so fix the read. Also, we only want to look at the one status bit, to allow for future use of the other bits, and watch for a bad PCI read. Fixes: 97ca486592c0 ("ionic: add heartbeat check") Signed-off-by: Shannon Nelson <snelson@pensando.io> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20net: macb: Properly handle phylink on at91rm9200Alexandre Belloni2-28/+33
at91ether_init was handling the phy mode and speed but since the switch to phylink, the NCFGR register got overwritten by macb_mac_config(). The issue is that the RM9200_RMII bit and the MACB_CLK_DIV32 field are cleared but never restored as they conflict with the PAE, GBE and PCSSEL bits. Add new capability to differentiate between EMAC and the other versions of the IP and use it to set and avoid clearing the relevant bits. Also, this fixes a NULL pointer dereference in macb_mac_link_up as the EMAC doesn't use any rings/bufffers/queues. Fixes: 7897b071ac3b ("net: macb: convert to phylink") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20s390/qeth: fix off-by-one in RX copybreak checkJulian Wiedmann1-1/+1
The RX copybreak is intended as the _max_ value where the frame's data should be copied. So for frame_len == copybreak, don't build an SG skb. Fixes: 4a71df50047f ("qeth: new qeth device driver") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20s390/qeth: don't warn for napi with 0 budgetJulian Wiedmann1-1/+0
Calling napi->poll() with 0 budget is a legitimate use by netpoll. Fixes: a1c3ed4c9ca0 ("qeth: NAPI support for l2 and l3 discipline") Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-20s390/qeth: vnicc Fix EOPNOTSUPP precedenceAlexandra Winter1-16/+13
When getting or setting VNICC parameters, the error code EOPNOTSUPP should have precedence over EBUSY. EBUSY is used because vnicc feature and bridgeport feature are mutually exclusive, which is a temporary condition. Whereas EOPNOTSUPP indicates that the HW does not support all or parts of the vnicc feature. This issue causes the vnicc sysfs params to show 'blocked by bridgeport' for HW that does not support VNICC at all. Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support") Signed-off-by: Alexandra Winter <wintera@linux.ibm.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-19ice: Wait for VF to be reset/ready before configurationBrett Creeley2-61/+76
The configuration/command below is failing when the VF in the xml file is already bound to the host iavf driver. pci_0000_af_0_0.xml: <interface type='hostdev' managed='yes'> <source> <address type='pci' domain='0x0000' bus='0xaf' slot='0x0' function='0x0'/> </source> <mac address='00:de:ad:00:11:01'/> </interface> > virsh attach-device domain_name pci_0000_af_0_0.xml error: Failed to attach device from pci_0000_af_0_0.xml error: Cannot set interface MAC/vlanid to 00:de:ad:00:11:01/0 for ifname ens1f1 vf 0: Device or resource busy This is failing because the VF has not been completely removed/reset after being unbound (via the virsh command above) from the host iavf driver and ice_set_vf_mac() checks if the VF is disabled before waiting for the reset to finish. Fix this by waiting for the VF remove/reset process to happen before checking if the VF is disabled. Also, since many functions for VF administration on the PF were more or less calling the same 3 functions (ice_wait_on_vf_reset(), ice_is_vf_disabled(), and ice_check_vf_init()) move these into the helper function ice_check_vf_ready_for_cfg(). Then call this function in any flow that attempts to configure/query a VF from the PF. Lastly, increase the maximum wait time in ice_wait_on_vf_reset() to 800ms, and modify/add the #define(s) that determine the wait time. This was done for robustness because in rare/stress cases VF removal can take a max of ~800ms and previously the wait was a max of ~300ms. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-02-19ice: Don't tell the OS that link is going downMichal Swiatkowski1-7/+0
Remove code that tell the OS that link is going down when user change flow control via ethtool. When link is up it isn't certain that link goes down after 0x0605 aq command. If link doesn't go down, OS thinks that link is down, but physical link is up. To reset this state user have to take interface down and up. If link goes down after 0x0605 command, FW send information about that and after that driver tells the OS that the link goes down. So this code in ethtool is unnecessary. Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-02-19ice: Don't reject odd values of usecs set by userBrett Creeley2-12/+39
Currently if a user sets an odd [tx|rx]-usecs value through ethtool, the request is denied because the hardware is set to have an ITR granularity of 2us. This caused poor customer experience. Fix this by aligning to a register allowed value, which results in rounding down. Also, print a once per ring container type message to be clear about our intentions. Also, change the ITR_TO_REG define to be the bitwise and of the ITR setting and the ICE_ITR_MASK. This makes the purpose of ITR_TO_REG more obvious. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2020-02-19nfc: pn544: Fix occasional HW initialization failureDmitry Osipenko1-0/+1
The PN544 driver checks the "enable" polarity during of driver's probe and it's doing that by turning ON and OFF NFC with different polarities until enabling succeeds. It takes some time for the hardware to power-down, and thus, to deassert the IRQ that is raised by turning ON the hardware. Since the delay after last power-down of the polarity-checking process is missed in the code, the interrupt may trigger immediately after installing the IRQ handler (right after the checking is done), which results in IRQ handler trying to touch the disabled HW and ends with marking NFC as 'DEAD' during of the driver's probe: pn544_hci_i2c 1-002a: NFC: nfc_en polarity : active high pn544_hci_i2c 1-002a: NFC: invalid len byte shdlc: llc_shdlc_recv_frame: NULL Frame -> link is dead This patch fixes the occasional NFC initialization failure on Nexus 7 device. Signed-off-by: Dmitry Osipenko <digetx@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18net/mlx5: DR, Handle reformat capability over sw-steering tablesErez Shitrit1-2/+7
On flow table creation, send the relevant flags according to what the FW currently supports. When FW doesn't support reformat option over SW-steering managed table, the driver shouldn't pass this. Fixes: 988fd6b32d07 ("net/mlx5: DR, Pass table flags at creation to lower layer") Signed-off-by: Erez Shitrit <erezsh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5: Fix lowest FDB pool sizePaul Blakey1-1/+1
The pool sizes represent the pool sizes in the fw. when we request a pool size from fw, it will return the next possible group. We track how many pools the fw has left and start requesting groups from the big to the small. When we start request 4k group, which doesn't exists in fw, fw wants to allocate the next possible size, 64k, but will fail since its exhausted. The correct smallest pool size in fw is 128 and not 4k. Fixes: 39ac237ce009 ("net/mlx5: E-Switch, Refactor chains and priorities") Signed-off-by: Paul Blakey <paulb@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5e: Don't clear the whole vf config when switching modesDmytro Linkin2-3/+7
There is no need to reset all vf config (except link state) between legacy and switchdev modes changes. Also, set link state to AUTO, when legacy enabled. Fixes: 3b83b6c2e024 ("net/mlx5e: Clear VF config when switching modes") Signed-off-by: Dmytro Linkin <dmitrolin@mellanox.com> Reviewed-by: Roi Dayan <roid@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5: DR, Fix matching on vport gvmiHamdan Igbaria1-1/+4
Set vport gvmi in the tag, only when source gvmi is set in the bit mask. Fixes: 26d688e3 ("net/mlx5: DR, Add Steering entry (STE) utilities") Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com> Reviewed-by: Alex Vesker <valex@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5e: Fix crash in recovery flow without devlink reporterAya Levin1-1/+1
When health reporters are not supported, recovery function is invoked directly, not via devlink health reporters. In this direct flow, the recover function input parameter was passed incorrectly and is causing a kernel oops. This patch is fixing the input parameter. Following call trace is observed on rx error health reporting. Internal error: Oops: 96000007 [#1] PREEMPT SMP Process kworker/u16:4 (pid: 4584, stack limit = 0x00000000c9e45703) Call trace: mlx5e_rx_reporter_err_rq_cqe_recover+0x30/0x164 [mlx5_core] mlx5e_health_report+0x60/0x6c [mlx5_core] mlx5e_reporter_rq_cqe_err+0x6c/0x90 [mlx5_core] mlx5e_rq_err_cqe_work+0x20/0x2c [mlx5_core] process_one_work+0x168/0x3d0 worker_thread+0x58/0x3d0 kthread+0x108/0x134 Fixes: c50de4af1d63 ("net/mlx5e: Generalize tx reporter's functionality") Signed-off-by: Aya Levin <ayal@mellanox.com> Signed-off-by: Parav Pandit <parav@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5e: Reset RQ doorbell counter before moving RQ state from RST to RDYAya Levin4-9/+43
Initialize RQ doorbell counters to zero prior to moving an RQ from RST to RDY state. Per HW spec, when RQ is back to RDY state, the descriptor ID on the completion is reset. The doorbell record must comply. Fixes: 8276ea1353a4 ("net/mlx5e: Report and recover from CQE with error on RQ") Signed-off-by: Aya Levin <ayal@mellanox.com> Reported-by: Tariq Toukan <tariqt@mellanox.com> Reviewed-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net/mlx5: Fix sleep while atomic in mlx5_eswitch_get_vepaHuy Nguyen1-11/+3
rtnl_bridge_getlink is protected by rcu lock, so mlx5_eswitch_get_vepa cannot take mutex lock. Two possible issues can happen: 1. User at the same time change vepa mode via RTM_SETLINK command. 2. User at the same time change the switchdev mode via devlink netlink interface. Case 1 cannot happen because rtnl executes one message in order. Case 2 can happen but we do not expect user to change the switchdev mode when changing vepa. Even if a user does it, so he will read a value which is no longer valid. Fixes: 8da202b24913 ("net/mlx5: E-Switch, Add support for VEPA in legacy mode.") Signed-off-by: Huy Nguyen <huyn@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2020-02-18net: phy: broadcom: Fix a typo ("firsly")Jonathan Neuschäfer1-2/+2
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-18qede: Fix race between rdma destroy workqueue and link change eventMichal Kalderon2-1/+30
If an event is added while the rdma workqueue is being destroyed it could lead to several races, list corruption, null pointer dereference during queue_work or init_queue. This fixes the race between the two flows which can occur during shutdown. A kref object and a completion object are added to the rdma_dev structure, these are initialized before the workqueue is created. The refcnt is used to indicate work is being added to the workqueue and ensures the cleanup flow won't start while we're in the middle of adding the event. Once the work is added, the refcnt is decreased and the cleanup flow is safe to run. Fixes: cee9fbd8e2e ("qede: Add qedr framework") Signed-off-by: Ariel Elior <ariel.elior@marvell.com> Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-17net: cnic: fix spelling mistake "reserverd" -> "reserved"Alexandre Belloni1-2/+2
The reserved member should be named reserved3. Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-17net: mscc: fix in frame extractionHoratiu Vultur1-0/+8
Each extracted frame on Ocelot has an IFH. The frame and IFH are extracted by reading chuncks of 4 bytes from a register. In case the IFH and frames were read corretly it would try to read the next frame. In case there are no more frames in the queue, it checks if there were any previous errors and in that case clear the queue. But this check will always succeed also when there are no errors. Because when extracting the IFH the error is checked against 4(number of bytes read) and then the error is set only if the extraction of the frame failed. So in a happy case where there are no errors the err variable is still 4. So it could be a case where after the check that there are no more frames in the queue, a frame will arrive in the queue but because the error is not reseted, it would try to flush the queue. So the frame will be lost. The fix consist in resetting the error after reading the IFH. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ethernet: dm9000: Handle -EPROBE_DEFER in dm9000_parse_dt()Paul Cercueil1-0/+2
The call to of_get_mac_address() can return -EPROBE_DEFER, for instance when the MAC address is read from a NVMEM driver that did not probe yet. Cc: H. Nikolaus Schaller <hns@goldelico.com> Cc: Mathieu Malaterre <malat@debian.org> Signed-off-by: Paul Cercueil <paul@crapouillou.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Fix 16-bit IO operationMarek Vasut1-2/+2
The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that BE[3:0] signals are active high. This contradicts the measurements of the behavior of the actual chip, where these signals behave as active low. For example, to read the CIDER register, the bus must expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Fix 16-bit data accessMarek Vasut1-2/+2
The packet data written to and read from Micrel KSZ8851-16MLLI must be byte-swapped in 16-bit mode, add this byte-swapping. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: ks8851-ml: Remove 8-bit bus accessorsMarek Vasut1-40/+5
This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown, however the speculation is that this was some sort of attempt to support the 8-bit bus mode. As per the KS8851-16MLL documentation, all two registers accessed via the 8-bit accessors are internally 16-bit registers, so reading them using 16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read outright, as it is already a concatenation of two 8-bit reads of that register. The KS_RXQCR accesses are 8-bit only, however writing the top 8 bits of the register is OK as well, since the driver caches the entire 16-bit register value anyway. Finally, the driver is not used by any hardware in the kernel right now. The only hardware available to me is one with 16-bit bus, so I have no way to test the 8-bit bus mode, however it is unlikely this ever really worked anyway. If the 8-bit bus mode is ever required, it can be easily added by adjusting the 16-bit accessors to do 2 consecutive accesses, which is how this should have been done from the beginning. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16bonding: fix lockdep warning in bond_get_stats()Taehee Yoo1-3/+50
In the "struct bonding", there is stats_lock. This lock protects "bond_stats" in the "struct bonding". bond_stats is updated in the bond_get_stats() and this function would be executed concurrently. So, the lock is needed. Bonding interfaces would be nested. So, either stats_lock should use dynamic lockdep class key or stats_lock should be used by spin_lock_nested(). In the current code, stats_lock is using a dynamic lockdep class key. But there is no updating stats_lock_key routine So, lockdep warning will occur. Test commands: ip link add bond0 type bond ip link add bond1 type bond ip link set bond0 master bond1 ip link set bond0 nomaster ip link set bond1 master bond0 Splat looks like: [ 38.420603][ T957] 5.5.0+ #394 Not tainted [ 38.421074][ T957] ------------------------------------------------------ [ 38.421837][ T957] ip/957 is trying to acquire lock: [ 38.422399][ T957] ffff888063262cd8 (&bond->stats_lock_key#2){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.423528][ T957] [ 38.423528][ T957] but task is already holding lock: [ 38.424526][ T957] ffff888065fd2cd8 (&bond->stats_lock_key){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.426075][ T957] [ 38.426075][ T957] which lock already depends on the new lock. [ 38.426075][ T957] [ 38.428536][ T957] [ 38.428536][ T957] the existing dependency chain (in reverse order) is: [ 38.429475][ T957] [ 38.429475][ T957] -> #1 (&bond->stats_lock_key){+.+.}: [ 38.430273][ T957] _raw_spin_lock+0x30/0x70 [ 38.430812][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ 38.431451][ T957] dev_get_stats+0x1ec/0x270 [ 38.432088][ T957] bond_get_stats+0x1a5/0x4d0 [bonding] [ 38.432767][ T957] dev_get_stats+0x1ec/0x270 [ 38.433322][ T957] rtnl_fill_stats+0x44/0xbe0 [ 38.433866][ T957] rtnl_fill_ifinfo+0xeb2/0x3720 [ 38.434474][ T957] rtmsg_ifinfo_build_skb+0xca/0x170 [ 38.435081][ T957] rtmsg_ifinfo_event.part.33+0x1b/0xb0 [ 38.436848][ T957] rtnetlink_event+0xcd/0x120 [ 38.437455][ T957] notifier_call_chain+0x90/0x160 [ 38.438067][ T957] netdev_change_features+0x74/0xa0 [ 38.438708][ T957] bond_compute_features.isra.45+0x4e6/0x6f0 [bonding] [ 38.439522][ T957] bond_enslave+0x3639/0x47b0 [bonding] [ 38.440225][ T957] do_setlink+0xaab/0x2ef0 [ 38.440786][ T957] __rtnl_newlink+0x9c5/0x1270 [ 38.441463][ T957] rtnl_newlink+0x65/0x90 [ 38.442075][ T957] rtnetlink_rcv_msg+0x4a8/0x890 [ 38.442774][ T957] netlink_rcv_skb+0x121/0x350 [ 38.443451][ T957] netlink_unicast+0x42e/0x610 [ 38.444282][ T957] netlink_sendmsg+0x65a/0xb90 [ 38.444992][ T957] ____sys_sendmsg+0x5ce/0x7a0 [ 38.445679][ T957] ___sys_sendmsg+0x10f/0x1b0 [ 38.446365][ T957] __sys_sendmsg+0xc6/0x150 [ 38.447007][ T957] do_syscall_64+0x99/0x4f0 [ 38.447668][ T957] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 38.448538][ T957] [ 38.448538][ T957] -> #0 (&bond->stats_lock_key#2){+.+.}: [ 38.449554][ T957] __lock_acquire+0x2d8d/0x3de0 [ 38.450148][ T957] lock_acquire+0x164/0x3b0 [ 38.450711][ T957] _raw_spin_lock+0x30/0x70 [ 38.451292][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ 38.451950][ T957] dev_get_stats+0x1ec/0x270 [ 38.452425][ T957] bond_get_stats+0x1a5/0x4d0 [bonding] [ 38.453362][ T957] dev_get_stats+0x1ec/0x270 [ 38.453825][ T957] rtnl_fill_stats+0x44/0xbe0 [ 38.454390][ T957] rtnl_fill_ifinfo+0xeb2/0x3720 [ 38.456257][ T957] rtmsg_ifinfo_build_skb+0xca/0x170 [ 38.456998][ T957] rtmsg_ifinfo_event.part.33+0x1b/0xb0 [ 38.459351][ T957] rtnetlink_event+0xcd/0x120 [ 38.460086][ T957] notifier_call_chain+0x90/0x160 [ 38.460829][ T957] netdev_change_features+0x74/0xa0 [ 38.461752][ T957] bond_compute_features.isra.45+0x4e6/0x6f0 [bonding] [ 38.462705][ T957] bond_enslave+0x3639/0x47b0 [bonding] [ 38.463476][ T957] do_setlink+0xaab/0x2ef0 [ 38.464141][ T957] __rtnl_newlink+0x9c5/0x1270 [ 38.464897][ T957] rtnl_newlink+0x65/0x90 [ 38.465522][ T957] rtnetlink_rcv_msg+0x4a8/0x890 [ 38.466215][ T957] netlink_rcv_skb+0x121/0x350 [ 38.466895][ T957] netlink_unicast+0x42e/0x610 [ 38.467583][ T957] netlink_sendmsg+0x65a/0xb90 [ 38.468285][ T957] ____sys_sendmsg+0x5ce/0x7a0 [ 38.469202][ T957] ___sys_sendmsg+0x10f/0x1b0 [ 38.469884][ T957] __sys_sendmsg+0xc6/0x150 [ 38.470587][ T957] do_syscall_64+0x99/0x4f0 [ 38.471245][ T957] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 38.472093][ T957] [ 38.472093][ T957] other info that might help us debug this: [ 38.472093][ T957] [ 38.473438][ T957] Possible unsafe locking scenario: [ 38.473438][ T957] [ 38.474898][ T957] CPU0 CPU1 [ 38.476234][ T957] ---- ---- [ 38.480171][ T957] lock(&bond->stats_lock_key); [ 38.480808][ T957] lock(&bond->stats_lock_key#2); [ 38.481791][ T957] lock(&bond->stats_lock_key); [ 38.482754][ T957] lock(&bond->stats_lock_key#2); [ 38.483416][ T957] [ 38.483416][ T957] *** DEADLOCK *** [ 38.483416][ T957] [ 38.484505][ T957] 3 locks held by ip/957: [ 38.485048][ T957] #0: ffffffffbccf6230 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x457/0x890 [ 38.486198][ T957] #1: ffff888065fd2cd8 (&bond->stats_lock_key){+.+.}, at: bond_get_stats+0x90/0x4d0 [bonding] [ 38.487625][ T957] #2: ffffffffbc9254c0 (rcu_read_lock){....}, at: bond_get_stats+0x5/0x4d0 [bonding] [ 38.488897][ T957] [ 38.488897][ T957] stack backtrace: [ 38.489646][ T957] CPU: 1 PID: 957 Comm: ip Not tainted 5.5.0+ #394 [ 38.490497][ T957] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 38.492810][ T957] Call Trace: [ 38.493219][ T957] dump_stack+0x96/0xdb [ 38.493709][ T957] check_noncircular+0x371/0x450 [ 38.494344][ T957] ? lookup_address+0x60/0x60 [ 38.494923][ T957] ? print_circular_bug.isra.35+0x310/0x310 [ 38.495699][ T957] ? hlock_class+0x130/0x130 [ 38.496334][ T957] ? __lock_acquire+0x2d8d/0x3de0 [ 38.496979][ T957] __lock_acquire+0x2d8d/0x3de0 [ 38.497607][ T957] ? register_lock_class+0x14d0/0x14d0 [ 38.498333][ T957] ? check_chain_key+0x236/0x5d0 [ 38.499003][ T957] lock_acquire+0x164/0x3b0 [ 38.499800][ T957] ? bond_get_stats+0x90/0x4d0 [bonding] [ 38.500706][ T957] _raw_spin_lock+0x30/0x70 [ 38.501435][ T957] ? bond_get_stats+0x90/0x4d0 [bonding] [ 38.502311][ T957] bond_get_stats+0x90/0x4d0 [bonding] [ ... ] But, there is another problem. The dynamic lockdep class key is protected by RTNL, but bond_get_stats() would be called outside of RTNL. So, it would use an invalid dynamic lockdep class key. In order to fix this issue, stats_lock uses spin_lock_nested() instead of a dynamic lockdep key. The bond_get_stats() calls bond_get_lowest_level_rcu() to get the correct nest level value, which will be used by spin_lock_nested(). The "dev->lower_level" indicates lower nest level value, but this value is invalid outside of RTNL. So, bond_get_lowest_level_rcu() returns valid lower nest level value in the RCU critical section. bond_get_lowest_level_rcu() will be work only when LOCKDEP is enabled. Fixes: 089bca2caed0 ("bonding: use dynamic lockdep key instead of subclass") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16bonding: add missing netdev_update_lockdep_key()Taehee Yoo2-0/+4
After bond_release(), netdev_update_lockdep_key() should be called. But both ioctl path and attribute path don't call netdev_update_lockdep_key(). This patch adds missing netdev_update_lockdep_key(). Test commands: ip link add bond0 type bond ip link add bond1 type bond ifenslave bond0 bond1 ifenslave -d bond0 bond1 ifenslave bond1 bond0 Splat looks like: [ 29.501182][ T1046] WARNING: possible circular locking dependency detected [ 29.501945][ T1039] hardirqs last disabled at (1962): [<ffffffffac6c807f>] handle_mm_fault+0x13f/0x700 [ 29.503442][ T1046] 5.5.0+ #322 Not tainted [ 29.503447][ T1046] ------------------------------------------------------ [ 29.504277][ T1039] softirqs last enabled at (1180): [<ffffffffade00678>] __do_softirq+0x678/0x981 [ 29.505443][ T1046] ifenslave/1046 is trying to acquire lock: [ 29.505886][ T1039] softirqs last disabled at (1169): [<ffffffffac19c18a>] irq_exit+0x17a/0x1a0 [ 29.509997][ T1046] ffff88805d5da280 (&dev->addr_list_lock_key#3){+...}, at: dev_mc_sync_multiple+0x95/0x120 [ 29.511243][ T1046] [ 29.511243][ T1046] but task is already holding lock: [ 29.512192][ T1046] ffff8880460f2280 (&dev->addr_list_lock_key#4){+...}, at: bond_enslave+0x4482/0x47b0 [bonding] [ 29.514124][ T1046] [ 29.514124][ T1046] which lock already depends on the new lock. [ 29.514124][ T1046] [ 29.517297][ T1046] [ 29.517297][ T1046] the existing dependency chain (in reverse order) is: [ 29.518231][ T1046] [ 29.518231][ T1046] -> #1 (&dev->addr_list_lock_key#4){+...}: [ 29.519076][ T1046] _raw_spin_lock+0x30/0x70 [ 29.519588][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.520208][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.520862][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ 29.521640][ T1046] __bond_opt_set+0x1ff/0xbb0 [bonding] [ 29.522438][ T1046] __bond_opt_set_notify+0x2b/0xf0 [bonding] [ 29.523251][ T1046] bond_opt_tryset_rtnl+0x92/0xf0 [bonding] [ 29.524082][ T1046] bonding_sysfs_store_option+0x8a/0xf0 [bonding] [ 29.524959][ T1046] kernfs_fop_write+0x276/0x410 [ 29.525620][ T1046] vfs_write+0x197/0x4a0 [ 29.526218][ T1046] ksys_write+0x141/0x1d0 [ 29.526818][ T1046] do_syscall_64+0x99/0x4f0 [ 29.527430][ T1046] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 29.528265][ T1046] [ 29.528265][ T1046] -> #0 (&dev->addr_list_lock_key#3){+...}: [ 29.529272][ T1046] __lock_acquire+0x2d8d/0x3de0 [ 29.529935][ T1046] lock_acquire+0x164/0x3b0 [ 29.530638][ T1046] _raw_spin_lock+0x30/0x70 [ 29.531187][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.531790][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.532451][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ 29.533163][ T1046] __bond_opt_set+0x1ff/0xbb0 [bonding] [ 29.533789][ T1046] __bond_opt_set_notify+0x2b/0xf0 [bonding] [ 29.534595][ T1046] bond_opt_tryset_rtnl+0x92/0xf0 [bonding] [ 29.535500][ T1046] bonding_sysfs_store_option+0x8a/0xf0 [bonding] [ 29.536379][ T1046] kernfs_fop_write+0x276/0x410 [ 29.537057][ T1046] vfs_write+0x197/0x4a0 [ 29.537640][ T1046] ksys_write+0x141/0x1d0 [ 29.538251][ T1046] do_syscall_64+0x99/0x4f0 [ 29.538870][ T1046] entry_SYSCALL_64_after_hwframe+0x49/0xbe [ 29.539659][ T1046] [ 29.539659][ T1046] other info that might help us debug this: [ 29.539659][ T1046] [ 29.540953][ T1046] Possible unsafe locking scenario: [ 29.540953][ T1046] [ 29.541883][ T1046] CPU0 CPU1 [ 29.542540][ T1046] ---- ---- [ 29.543209][ T1046] lock(&dev->addr_list_lock_key#4); [ 29.543880][ T1046] lock(&dev->addr_list_lock_key#3); [ 29.544873][ T1046] lock(&dev->addr_list_lock_key#4); [ 29.545863][ T1046] lock(&dev->addr_list_lock_key#3); [ 29.546525][ T1046] [ 29.546525][ T1046] *** DEADLOCK *** [ 29.546525][ T1046] [ 29.547542][ T1046] 5 locks held by ifenslave/1046: [ 29.548196][ T1046] #0: ffff88806044c478 (sb_writers#5){.+.+}, at: vfs_write+0x3bb/0x4a0 [ 29.549248][ T1046] #1: ffff88805af00890 (&of->mutex){+.+.}, at: kernfs_fop_write+0x1cf/0x410 [ 29.550343][ T1046] #2: ffff88805b8b54b0 (kn->count#157){.+.+}, at: kernfs_fop_write+0x1f2/0x410 [ 29.551575][ T1046] #3: ffffffffaecf4cf0 (rtnl_mutex){+.+.}, at: bond_opt_tryset_rtnl+0x5f/0xf0 [bonding] [ 29.552819][ T1046] #4: ffff8880460f2280 (&dev->addr_list_lock_key#4){+...}, at: bond_enslave+0x4482/0x47b0 [bonding] [ 29.554175][ T1046] [ 29.554175][ T1046] stack backtrace: [ 29.554907][ T1046] CPU: 0 PID: 1046 Comm: ifenslave Not tainted 5.5.0+ #322 [ 29.555854][ T1046] Hardware name: innotek GmbH VirtualBox/VirtualBox, BIOS VirtualBox 12/01/2006 [ 29.557064][ T1046] Call Trace: [ 29.557504][ T1046] dump_stack+0x96/0xdb [ 29.558054][ T1046] check_noncircular+0x371/0x450 [ 29.558723][ T1046] ? print_circular_bug.isra.35+0x310/0x310 [ 29.559486][ T1046] ? hlock_class+0x130/0x130 [ 29.560100][ T1046] ? __lock_acquire+0x2d8d/0x3de0 [ 29.560761][ T1046] __lock_acquire+0x2d8d/0x3de0 [ 29.561366][ T1046] ? register_lock_class+0x14d0/0x14d0 [ 29.562045][ T1046] ? find_held_lock+0x39/0x1d0 [ 29.562641][ T1046] lock_acquire+0x164/0x3b0 [ 29.563199][ T1046] ? dev_mc_sync_multiple+0x95/0x120 [ 29.563872][ T1046] _raw_spin_lock+0x30/0x70 [ 29.564464][ T1046] ? dev_mc_sync_multiple+0x95/0x120 [ 29.565146][ T1046] dev_mc_sync_multiple+0x95/0x120 [ 29.565793][ T1046] bond_enslave+0x448d/0x47b0 [bonding] [ 29.566487][ T1046] ? bond_update_slave_arr+0x940/0x940 [bonding] [ 29.567279][ T1046] ? bstr_printf+0xc20/0xc20 [ 29.567857][ T1046] ? stack_trace_consume_entry+0x160/0x160 [ 29.568614][ T1046] ? deactivate_slab.isra.77+0x2c5/0x800 [ 29.569320][ T1046] ? check_chain_key+0x236/0x5d0 [ 29.569939][ T1046] ? sscanf+0x93/0xc0 [ 29.570442][ T1046] ? vsscanf+0x1e20/0x1e20 [ 29.571003][ T1046] bond_option_slaves_set+0x1a3/0x370 [bonding] [ ... ] Fixes: ab92d68fc22f ("net: core: add generic lockdep keys") Signed-off-by: Taehee Yoo <ap420073@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16NFC: pn544: Fix a typo in a debug messageChristophe JAILLET1-1/+1
The ending character of the string shoulb be \n, not \b. Fixes: 17936b43f0fd ("NFC: Standardize logging style") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: dsa: b53: Ensure the default VID is untaggedFlorian Fainelli1-0/+3
We need to ensure that the default VID is untagged otherwise the switch will be sending tagged frames and the results can be problematic. This is especially true with b53 switches that use VID 0 as their default VLAN since VID 0 has a special meaning. Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID") Fixes: 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation") Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: socket: remove extra call to synchronize_netJason A. Donenfeld1-1/+0
synchronize_net() is a wrapper around synchronize_rcu(), so there's no point in having synchronize_net and synchronize_rcu back to back, despite the documentation comment suggesting maybe it's somewhat useful, "Wait for packets currently being received to be done." This commit removes the extra call. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Suggested-by: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: send: account for mtu=0 devicesJason A. Donenfeld2-8/+15
It turns out there's an easy way to get packets queued up while still having an MTU of zero, and that's via persistent keep alive. This commit makes sure that in whatever condition, we don't wind up dividing by zero. Note that an MTU of zero for a wireguard interface is something quasi-valid, so I don't think the correct fix is to limit it via min_mtu. This can be reproduced easily with: ip link add wg0 type wireguard ip link add wg1 type wireguard ip link set wg0 up mtu 0 ip link set wg1 up wg set wg0 private-key <(wg genkey) wg set wg1 listen-port 1 private-key <(wg genkey) peer $(wg show wg0 public-key) wg set wg0 peer $(wg show wg1 public-key) persistent-keepalive 1 endpoint 127.0.0.1:1 However, while min_mtu=0 seems fine, it makes sense to restrict the max_mtu. This commit also restricts the maximum MTU to the greatest number for which rounding up to the padding multiple won't overflow a signed integer. Packets this large were always rejected anyway eventually, due to checks deeper in, but it seems more sound not to even let the administrator configure something that won't work anyway. We use this opportunity to clean up this function a bit so that it's clear which paths we're expecting. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Cc: Eric Dumazet <eric.dumazet@gmail.com> Reviewed-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16wireguard: receive: reset last_under_load to zeroJason A. Donenfeld1-2/+5
This is a small optimization that prevents more expensive comparisons from happening when they are no longer necessary, by clearing the last_under_load variable whenever we wind up in a state where we were under load but we no longer are. Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com> Suggested-by: Matt Dunwoodie <ncon@noconroy.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: phy: restore mdio regs in the iproc mdio driverArun Parameswaran1-0/+20
The mii management register in iproc mdio block does not have a retention register so it is lost on suspend. Save and restore value of register while resuming from suspend. Fixes: bb1a619735b4 ("net: phy: Initialize mdio clock at probe function") Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com> Signed-off-by: Scott Branden <scott.branden@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix out of range usage of active_vlans arrayDmitry Bogdanov1-1/+1
fix static checker warning: drivers/net/ethernet/aquantia/atlantic/aq_filters.c:166 aq_check_approve_fvlan() error: passing untrusted data to 'test_bit()' Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Fixes: 7975d2aff5af: ("net: aquantia: add support of rx-vlan-filter offload") Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: possible fault in transition to hibernationPavel Belous1-5/+8
during hibernation freeze, aq_nic_stop could be invoked on a stopped device. That may cause panic on access to not yet allocated vector/ring structures. Add a check to stop device if it is not yet stopped. Similiarly after freeze in hibernation thaw, aq_nic_start could be invoked on a not initialized net device. Result will be the same. Add a check to start device if it is initialized. In our case, this is the same as started. Fixes: 8aaa112a57c1 ("net: atlantic: refactoring pm logic") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix potential error handlingPavel Belous1-1/+3
Code inspection found that in case of mapping error we do return current 'ret' value. But beside error, it is used to count number of descriptors allocated for the packet. In that case map_skb function could return '1'. Changing it to return zero (number of mapped descriptors for skb) Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: fix use after free kasan warnPavel Belous2-6/+5
skb->len is used to calculate statistics after xmit invocation. Under a stress load it may happen that skb will be xmited, rx interrupt will come and skb will be freed, all before xmit function is even returned. Eventually, skb->len will access unallocated area. Moving stats calculation into tx_clean routine. Fixes: 018423e90bee ("net: ethernet: aquantia: Add ring support code") Reported-by: Christophe Vu-Brugier <cvubrugier@fastmail.fm> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Pavel Belous <pbelous@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: better loopback mode handlingNikita Danilov2-5/+13
Add checks to not enable multiple loopback modes simultaneously, It was also discovered that for dma loopback to function correctly promisc mode should be enabled on device. Fixes: ea4b4d7fc106 ("net: atlantic: loopback tests via private flags") Signed-off-by: Nikita Danilov <ndanilov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: ptp gpio adjustmentsEgor Pomozov3-1/+17
Clock adjustment data should be passed to FW as well, otherwise in some cases a drift was observed when using GPIO features. Signed-off-by: Egor Pomozov <epomozov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: check rpc result and wait for rpc addressIgor Russkikh1-2/+17
Artificial HW reliability tests revealed a possible hangup in the driver. Normally, when device disappears from bus, all register reads returns 0xFFFFFFFF. At remote procedure invocation towards FW there is a logic where result is compared with -1 in a loop. That caused an infinite loop if hardware due to some issues disappears from bus. Add extra result checks to prevent this. Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: atlantic: checksum compat issueDmitry Bezrukov3-4/+7
Yet another checksum offload compatibility issue was found. The known issue is that AQC HW marks tcp packets with 0xFFFF checksum as invalid (1). This is workarounded in driver, passing all the suspicious packets up to the stack for further csum validation. Another HW problem (2) is that it hides invalid csum of LRO aggregated packets inside of the individual descriptors. That was workarounded by forced scan of all LRO descriptors for checksum errors. However the scan logic was joint for both LRO and multi-descriptor packets (jumbos). And this causes the issue. We have to drop LRO packets with the detected bad checksum because of (2), but we have to pass jumbo packets to stack because of (1). When using windows tcp partner with jumbo frames but with LSO disabled driver discards such frames as bad checksummed. But only LRO frames should be dropped, not jumbos. On such a configurations tcp stream have a chance of drops and stucks. (1) 76f254d4afe2 ("net: aquantia: tcp checksum 0xffff being handled incorrectly") (2) d08b9a0a3ebd ("net: aquantia: do not pass lro session with invalid tcp checksum") Fixes: d08b9a0a3ebd ("net: aquantia: do not pass lro session with invalid tcp checksum") Signed-off-by: Dmitry Bezrukov <dbezrukov@marvell.com> Signed-off-by: Igor Russkikh <irusskikh@marvell.com> Signed-off-by: Dmitry Bogdanov <dbogdanov@marvell.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-16net: macb: ensure interface is not suspended on at91rm9200Alexandre Belloni1-1/+5
Because of autosuspend, at91ether_start is called with clocks disabled. Ensure that pm_runtime doesn't suspend the interface as soon as it is opened as there is no pm_runtime support is the other relevant parts of the platform support for at91rm9200. Fixes: d54f89af6cc4 ("net: macb: Add pm runtime support") Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds33-785/+421
Pull networking fixes from David Miller: 1) Fix interrupt name truncation in mv88e6xxx dsa driver, from Andrew Lunn. 2) Process generic XDP even if SKB is cloned, from Toke Høiland-Jørgensen. 3) Fix leak of kernel memory to userspace in smc, from Eric Dumazet. 4) Add some missing netlink attribute validation to matchall and flower, from Davide Caratti. 5) Send icmp responses properly when NAT has been applied to the frame before we get to the tunnel emitting the icmp, from Jason Donenfeld. 6) Make sure there is enough SKB headroom when adding dsa tags for qca and ar9331. From Per Forlin. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (62 commits) netdevice.h: fix all kernel-doc and Sphinx warnings net: dsa: tag_ar9331: Make sure there is headroom for tag net: dsa: tag_qca: Make sure there is headroom for tag net, ip6_tunnel: enhance tunnel locate with link check net/smc: no peer ID in CLC decline for SMCD net/smc: transfer fasync_list in case of fallback net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples() net: hns3: fix VF bandwidth does not take effect in some case net: hns3: add management table after IMP reset mac80211: fix wrong 160/80+80 MHz setting cfg80211: add missing policy for NL80211_ATTR_STATUS_CODE xfrm: interface: use icmp_ndo_send helper wireguard: device: use icmp_ndo_send helper sunvnet: use icmp_ndo_send helper gtp: use icmp_ndo_send helper icmp: introduce helper for nat'd source address in network device context net/sched: flower: add missing validation of TCA_FLOWER_FLAGS net/sched: matchall: add missing validation of TCA_MATCHALL_FLAGS net/flow_dissector: remove unexist field description page_pool: refill page when alloc.count of pool is zero ...
2020-02-14Merge tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pmLinus Torvalds6-34/+170
Pull power management fixes from Rafael Wysocki: "Fix three issues related to the handling of wakeup events signaled through the ACPI SCI while suspended to idle (Rafael Wysocki) and unexport an internal cpufreq variable (Yangtao Li)" * tag 'pm-5.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: ACPI: PM: s2idle: Prevent spurious SCIs from waking up the system ACPICA: Introduce acpi_any_gpe_status_set() ACPI: PM: s2idle: Avoid possible race related to the EC GPE ACPI: EC: Fix flushing of pending work cpufreq: Make cpufreq_global_kobject static
2020-02-14Merge tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drmLinus Torvalds51-251/+1131
Pull drm fixes from Dave Airlie: "The core has a build fix for edid code on certain compilers/arches/, one MST fix and one vgem fix. Regular amdgpu fixes, and a couple of small driver fixes. The i915 fixes are bit larger than normal for this stage, but they were having CI issues last week, and they hadn't sent any fixes last week due to this. core: - edid build fix mst: - fix NULL ptr deref vgem: - fix close after free msm: - better dma-api usage sun4i: - disable allow_fb_modifiers amdgpu: - Additional OD fixes for navi - Misc display fixes - VCN 2.5 DPG fix - Prevent build errors on PowerPC on some configs - GDS EDC fix i915: - dsi/acpi fixes - gvt locking and allocation fixes - gem/gt fixes - bios timing parameters fix" * tag 'drm-fixes-2020-02-14' of git://anongit.freedesktop.org/drm/drm: (50 commits) drm/i915: Mark the removal of the i915_request from the sched.link drm/i915/execlists: Reclaim the hanging virtual request drm/i915/execlists: Take a reference while capturing the guilty request drm/i915/execlists: Offline error capture drm/i915/gt: Allow temporary suspension of inflight requests drm/i915: Keep track of request among the scheduling lists drm/i915/gem: Tighten checks and acquiring the mmap object drm/i915: Fix preallocated barrier list append drm/i915/gt: Acquire ce->active before ce->pin_count/ce->pin_mutex drm/i915: Tighten atomicity of i915_active_acquire vs i915_active_release drm/i915: Stub out i915_gpu_coredump_put drm/amdgpu:/navi10: use the ODCAP enum to index the caps array drm/amdgpu: update smu_v11_0_pptable.h drm/amdgpu: correct comment to clear up the confusion drm/amd/display: DCN2.x Do not program DPPCLK if same value drm/amd/display: Don't map ATOM_ENABLE to ATOM_INIT drm/amdgpu/vcn2.5: fix warning drm/amdgpu: limit GDS clearing workaround in cold boot sequence drm/amdgpu: fix amdgpu pmu to use hwc->config instead of hwc->conf amdgpu: Prevent build errors regarding soft/hard-float FP ABI tags ...
2020-02-14net: hns3: fix a copying IPv6 address error in hclge_fd_get_flow_tuples()Guangbin Huang1-6/+9
The IPv6 address defined in struct in6_addr is specified as big endian, but there is no specified endian in struct hclge_fd_rule_tuples, so it will cause a problem if directly use memcpy() to copy ipv6 address between these two structures since this field in struct hclge_fd_rule_tuples is little endian. This patch fixes this problem by using be32_to_cpu() to convert endian of IPv6 address of struct in6_addr before copying. Fixes: d93ed94fbeaf ("net: hns3: add aRFS support for PF") Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net: hns3: fix VF bandwidth does not take effect in some caseYonglong Liu1-1/+1
When enabling 4 TC after setting the bandwidth of VF, the bandwidth of VF will resume to default value, because of the qset resources changed in this case. This patch fixes it by using a fixed VF's qset resources according to HNAE3_MAX_TC macro. Fixes: ee9e44248f52 ("net: hns3: add support for configuring bandwidth of VF on the host") Signed-off-by: Yonglong Liu <liuyonglong@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14net: hns3: add management table after IMP resetYufeng Mo1-0/+7
In the current process, the management table is missing after the IMP reset. This patch adds the management table to the reset process. Fixes: f5aac71c0327 ("net: hns3: add manager table initialization for hardware") Signed-off-by: Yufeng Mo <moyufeng@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-14Merge branch 'pm-cpufreq'Rafael J. Wysocki1-3/+2
* pm-cpufreq: cpufreq: Make cpufreq_global_kobject static
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.