aboutsummaryrefslogtreecommitdiffstats
path: root/drivers (follow)
AgeCommit message (Collapse)AuthorFilesLines
2016-11-30sfc: separate out SFC4000 ("Falcon") support into new sfc-falcon driverEdward Cree44-1220/+18213
Rationale: The differences between Falcon and Siena are in many ways larger than those between Siena and EF10 (despite Siena being nominally "Falcon- architecture"); for instance, Falcon has no MCPU, so there is no MCDI. Removing Falcon support from the sfc driver should simplify the latter, and avoid the possibility of Falcon support being broken by changes to sfc (which are rarely if ever tested on Falcon, it being end-of-lifed hardware). The sfc-falcon driver created in this changeset is essentially a copy of the sfc driver, but with Siena- and EF10-specific code, including MCDI, removed and with the "efx_" identifier prefix changed to "ef4_" (for "EFX 4000- series") to avoid collisions when both drivers are built-in. This changeset removes Falcon from the sfc driver's PCI ID table; then in sfc I've removed obvious Falcon-related code: I removed the Falcon NIC functions, Falcon PHY code, and EFX_REV_FALCON_*, then fixed up everything that referenced them. Also, increment minor version of both drivers (to 4.1). For now, CONFIG_SFC selects CONFIG_SFC_FALCON, so that updating old configs doesn't cause Falcon support to disappear; but that should be undone at some point in the future. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-30cpsw: ethtool: add support for nway resetYegor Yefremov1-0/+13
This patch adds support for ethtool's '-r' command. Restarting N-WAY negotiation can be useful to activate newly changed EEE settings etc. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-30cpsw: ethtool: add support for getting/setting EEE registersYegor Yefremov1-0/+26
Add the ability to query and set Energy Efficient Ethernet parameters via ethtool for applicable devices. This patch doesn't activate full EEE support in cpsw driver, but it enables reading and writing EEE advertising settings. This way one can disable advertising EEE for certain speeds. Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Acked-by: Rami Rosen <roszenrami@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29hv_netvsc: remove excessive logging on MTU changeVitaly Kuznetsov2-7/+7
When we change MTU or the number of channels on a netvsc device we get the following logged: hv_netvsc bf5edba8...: net device safe to remove hv_netvsc: hv_netvsc channel opened successfully hv_netvsc bf5edba8...: Send section size: 6144, Section count:2560 hv_netvsc bf5edba8...: Device MAC 00:15:5d:1e:91:12 link state up This information is useful as debug at most. Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com> Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29mlxsw: core: Change order of operations in removal pathIdo Schimmel1-1/+1
We call bus->init() before allocating 'lag.mapping'. Change the order of operations in removal path to reflect that. This makes the error path of mlxsw_core_bus_device_register() symmetric with mlxsw_core_bus_device_unregister(). Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29mlxsw: core: Add missing rollback in error pathIdo Schimmel1-0/+1
Without this rollback, the thermal zone is still registered during the error path, whereas its private data is freed upon the destruction of the underlying bus device due to the use of devm_kzalloc(). This results in use after free. Fix this by calling mlxsw_thermal_fini() from the appropriate place in the error path. Fixes: a50c1e35650b ("mlxsw: core: Implement thermal zone") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29mlxsw: spectrum_buffers: Limit size of poolsIdo Schimmel1-0/+3
The shared buffer pools are containers whose size is used to calculate the maximum usage for packets from / to a specific port / {port, PG/TC}, when dynamic threshold is employed. While it's perfectly fine for the sum of the pools to exceed the maximum size of the shared buffer, a single pool cannot. Add a check when the pool size is set and forbid sizes larger than the maximum size of the shared buffer. Without the patch: $ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype dynamic // No error is returned With the patch: $ devlink sb pool set pci/0000:03:00.0 pool 0 size 999999999 thtype dynamic devlink answers: Invalid argument Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29mlxsw: resources: Add maximum buffer sizeIdo Schimmel1-0/+2
We need to be able to limit the size of shared buffer pools, so query the maximum size from the device during init. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29mlxsw: switchib: add MLXSW_PCI dependencyArnd Bergmann1-1/+1
The newly added switchib driver fails to link if MLXSW_PCI=m: drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function^Cmlxsw_sib_module_exit': switchib.c:(.exit.text+0x8): undefined reference to `mlxsw_pci_driver_unregister' switchib.c:(.exit.text+0x10): undefined reference to `mlxsw_pci_driver_unregister' drivers/net/ethernet/mellanox/mlxsw/mlxsw_switchib.o: In function `mlxsw_sib_module_init': switchib.c:(.init.text+0x28): undefined reference to `mlxsw_pci_driver_register' switchib.c:(.init.text+0x38): undefined reference to `mlxsw_pci_driver_register' switchib.c:(.init.text+0x48): undefined reference to `mlxsw_pci_driver_unregister' The other two such sub-drivers have a dependency, so add the same one here. In theory we could allow this driver if MLXSW_PCI is disabled, but it's probably not worth it. Fixes: d1ba52638456 ("mlxsw: switchib: Introduce SwitchIB and SwitchIB silicon driver") Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29net: phy: Fix use after free in phy_detach()Geert Uytterhoeven1-2/+2
If device_release_driver(&phydev->mdio.dev) is called, it releases all resources belonging to the PHY device. Hence the subsequent call to phy_led_triggers_unregister() will access already freed memory when unregistering the LEDs. Move the call to phy_led_triggers_unregister() before the possible call to device_release_driver() to fix this. Fixes: 2e0bc452f4721520 ("net: phy: leds: add support for led triggers on phy link state change") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Zach Brown <zach.brown@ni.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29stmmac: fix comments, make debug output consistentPavel Machek2-7/+10
Fix comments, add some new, and make debugfs output consistent. Signed-off-by: Pavel Machek <pavel@denx.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29net: phy: add an option to disable EEE advertisementjbrunet2-9/+74
This patch adds an option to disable EEE advertisement in the generic PHY by providing a mask of prohibited modes corresponding to the value found in the MDIO_AN_EEE_ADV register. On some platforms, PHY Low power idle seems to be causing issues, even breaking the link some cases. The patch provides a convenient way for these platforms to disable EEE advertisement and work around the issue. Signed-off-by: Jerome Brunet <jbrunet@baylibre.com> Tested-by: Yegor Yefremov <yegorslists@googlemail.com> Tested-by: Andreas Färber <afaerber@suse.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29net: stmmac: enable tx queue 0 for gmac4 IPs synthesized with multiple TX queuesNiklas Cassel2-1/+14
The dwmac4 IP can synthesized with 1-8 number of tx queues. On an IP synthesized with DWC_EQOS_NUM_TXQ > 1, all txqueues are disabled by default. For these IPs, the bitfield TXQEN is R/W. Always enable tx queue 0. The write will have no effect on IPs synthesized with DWC_EQOS_NUM_TXQ == 1. The driver does still not utilize more than one tx queue in the IP. Signed-off-by: Niklas Cassel <niklas.cassel@axis.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29net: arc_emac: add dependencies on associated arches and compile testPeter Robinson1-2/+3
Add dependencies on the architectures that support these devices and add compile test to ensure ongoing code build coverage. Signed-off-by: Peter Robinson <pbrobinson@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-29mlx4: give precise rx/tx bytes/packets countersEric Dumazet4-23/+58
mlx4 stats are chaotic because a deferred work queue is responsible to update them every 250 ms. Even sampling stats every one second with "sar -n DEV 1" gives variations like the following : lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65 07:39:22 eth0 146877.00 3265554.00 9467.15 4828168.50 07:39:23 eth0 146587.00 3260329.00 9448.15 4820445.98 07:39:24 eth0 146894.00 3259989.00 9468.55 4819943.26 07:39:25 eth0 110368.00 2454497.00 7113.95 3629012.17 <<>> 07:39:26 eth0 146563.00 3257502.00 9447.25 4816266.23 07:39:27 eth0 145678.00 3258292.00 9389.79 4817414.39 07:39:28 eth0 145268.00 3253171.00 9363.85 4809852.46 07:39:29 eth0 146439.00 3262185.00 9438.97 4823172.48 07:39:30 eth0 146758.00 3264175.00 9459.94 4826124.13 07:39:31 eth0 146843.00 3256903.00 9465.44 4815381.97 Average: eth0 142827.50 3179259.70 9206.30 4700578.16 This patch allows rx/tx bytes/packets counters being folded at the time we need stats. We now can fetch stats every 1 ms if we want to check NIC behavior on a small time window. It is also easier to detect anomalies. lpaa23:~# sar -n DEV 1 10 | grep eth0 | cut -c1-65 07:42:50 eth0 142915.00 3177696.00 9212.06 4698270.42 07:42:51 eth0 143741.00 3200232.00 9265.15 4731593.02 07:42:52 eth0 142781.00 3171600.00 9202.92 4689260.16 07:42:53 eth0 143835.00 3192932.00 9271.80 4720761.39 07:42:54 eth0 141922.00 3165174.00 9147.64 4679759.21 07:42:55 eth0 142993.00 3207038.00 9216.78 4741653.05 07:42:56 eth0 141394.06 3154335.64 9113.85 4663731.73 07:42:57 eth0 141850.00 3161202.00 9144.48 4673866.07 07:42:58 eth0 143439.00 3180736.00 9246.05 4702755.35 07:42:59 eth0 143501.00 3210992.00 9249.99 4747501.84 Average: eth0 142835.66 3182165.93 9206.98 4704874.08 Signed-off-by: Eric Dumazet <edumazet@google.com> Cc: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28geneve: fix ip_hdr_len reserved for geneve6 tunnel.Haishuang Yan1-1/+1
It shold reserved sizeof(ipv6hdr) for geneve in ipv6 tunnel. Fixes: c3ef5aa5e5 ('geneve: Merge ipv4 and ipv6 geneve_build_skb()') Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net: dsa: mv88e6xxx: Fix mv88e6xxx_g1_irq_free() interrupt countAndreas Färber1-1/+1
mv88e6xxx_g1_irq_setup() sets up chip->g1_irq.nirqs interrupt mappings, so free the same amount. This will be 8 or 9 in practice, less than 16. Fixes: dc30c35be720 ("net: dsa: mv88e6xxx: Implement interrupt support.") Cc: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Andreas Färber <afaerber@suse.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Add CQE compression user controlShaker Daibes5-13/+51
The user can now override the automatic driver decision using the rx_cqe_compress flag, which is the preference for CQE compression. The flag is initialized with the automatic driver decision. Signed-off-by: Shaker Daibes <shakerd@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Moves pflags to priv->paramsShaker Daibes3-12/+14
pflags is a configuration parameter for the netdev, naturally it belongs to priv->params. Also introduce MLX5E_GET_PFLAG Signed-off-by: Shaker Daibes <shakerd@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Add support for loopback selftestSaeed Mahameed4-3/+227
Extend the self diagnostic tests to support loopback test. The loopback test doesn't require the offline flag, it will use the generic dev_queue_xmit and a dedicated packet_type to capture and verify mlx5e selftest loopback packets. Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Add support for ethtool self diagnostics testKamal Heib4-2/+139
The self diagnostics test implementaion include the following features: 1. Link Test: Check that link is in up state. 2. Speed Test: Check that link was negotiated correctly. 3. Health Test: Check the device health. Signed-off-by: Kamal Heib <kamalh@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Add DCBX control interfaceHuy Nguyen1-3/+24
Use setdcbx interface to set the DCBX mode to firmware or os. If setdcbx is called with mode value of zero, the DCBX mode is set to firmware. Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: ConnectX-4 firmware support for DCBXHuy Nguyen3-28/+94
DBCX by default is controlled by firmware where dcbx capability bit is set. In this mode, firmware is responsible for reading/sending the TLV packets from/to the remote partner. This patch sets up the infrastructure to move between HOST/FW DCBX control mode. Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5: Add DCBX firmware commands supportHuy Nguyen1-0/+20
Add set/query commands for DCBX_PARAM register Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Read ETS settings directly from firmwareHuy Nguyen3-25/+56
Issue description: Current implementation saves the ETS settings from user in a temporal soft copy and returns this settings when user queries the ETS settings. With the new DCBX firmware, the ETS settings can be changed by firmware when the DCBX is in firmware controlled mode. Therefore, user will obtain wrong values from the temporal soft copy. Solution: 1. Read the ETS settings directly from firmware. 2. For tc_tsa: a. Initialize tc_tsa to vendor IEEE_8021QAZ_TSA_VENDOR at netdev creation. b. When reading ETS setting from FW, if the traffic class bandwidth is less than 100, set tc_tsa to IEEE_8021QAZ_TSA_ETS. This implementation solves the scenarios when the DCBX is in FW control and willing bit is on which means the ETS setting is dictated by remote switch. Also check ETS capability where needed. Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Support DCBX CEE APIHuy Nguyen3-2/+366
Add DCBX CEE API interface for ConnectX-4. Configurations are stored in a temporary structure and are applied to the card's firmware when the CEE's setall callback function is called. Note: priority group in CEE is equivalent to traffic class in ConnectX-4 hardware spec. bw allocation per priority in CEE is not supported because ConnectX-4 only supports bw allocation per traffic class. user priority in CEE does not have an equivalent term in ConnectX-4. Therefore, user priority to priority mapping in CEE is not supported. Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net/mlx5e: Add qos capability checkHuy Nguyen1-1/+2
Make sure firmware supports qos before exposing the DCB API. Signed-off-by: Huy Nguyen <huyn@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28virtio-net: enable multiqueue by defaultJason Wang1-2/+7
We use single queue even if multiqueue is enabled and let admin to enable it through ethtool later. This is used to avoid possible regression (small packet TCP stream transmission). But looks like an overkill since: - single queue user can disable multiqueue when launching qemu - brings extra troubles for the management since it needs extra admin tool in guest to enable multiqueue - multiqueue performs much better than single queue in most of the cases So this patch enables multiqueue by default: if #queues is less than or equal to #vcpu, enable as much as queue pairs; if #queues is greater than #vcpu, enable #vcpu queue pairs. Cc: Hannes Frederic Sowa <hannes@redhat.com> Cc: Michael S. Tsirkin <mst@redhat.com> Cc: Neil Horman <nhorman@redhat.com> Cc: Jeremy Eder <jeder@redhat.com> Cc: Marko Myllynen <myllynen@redhat.com> Cc: Maxime Coquelin <maxime.coquelin@redhat.com> Signed-off-by: Jason Wang <jasowang@redhat.com> Acked-by: Neil Horman <nhorman@tuxdriver.com> Acked-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net: dsa: mv88e6xxx: add missing comment for MV88E6097Stefan Eichenberger1-0/+1
Add a missing comment for the MV88E6097 because of unification. Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-28net: dsa: mv88e6xxx: add g1_irqs definition for MV88E6097Stefan Eichenberger1-0/+1
Add the missing definition of g1_irqs for MV88E6097. Signed-off-by: Stefan Eichenberger <stefan.eichenberger@netmodule.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-27bpf: drop unnecessary context cast from BPF_PROG_RUNDaniel Borkmann1-1/+1
Since long already bpf_func is not only about struct sk_buff * as input anymore. Make it generic as void *, so that callers don't need to cast for it each time they call BPF_PROG_RUN(). Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Alexei Starovoitov <ast@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-27sfc: remove unneeded variableDan Carpenter2-9/+1
We don't use ->heap_buf after commit 46d1efd852cc ("sfc: remove Software TSO") so let's remove the last traces. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-27Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-nextDavid S. Miller186-1148/+1553
Kalle Valo says: ==================== wireless-drivers-next patches for 4.10 Major changes: iwlwifi * finalize and enable dynamic queue allocation * use dev_coredumpmsg() to prevent locking the driver * small fix to pass the AID to the FW * use FW PS decisions with multi-queue ath9k * add device tree bindings * switch to use mac80211 intermediate software queues to reduce latency and fix bufferbloat wl18xx * allow scanning in AP mode ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-27ptp: gianfar: Use high resolution frequency method.Ulrik De Bie1-8/+13
This patch depends on commit d8d263541913 ("ptp: Introduce a high resolution frequency adjustment method.") The gianfar devices offer a frequency resolution of about 0.46 ppb (depends on actual value of tmr_add, for the calculation assumed 0x80000000). This patch lets users of the device benefit from the increased frequency resolution when tuning the clock. Thanks to the rounding the maximum error between the requested frequency and the applied frequency will then be about 0.23 ppb. Tested on a v3.3.8 kernel on a real gianfar device. Verified compilation on net-next (currently at v4.9-rc5). Signed-off-by: Ulrik De Bie <ulrik.debie-os@e2big.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-27mlx4: do not use priv->stats_lock in mlx4_en_auto_moderation()Eric Dumazet1-4/+2
Per RX ring packets/bytes counters are not protected by global priv->stats_lock. Better not confuse the reader, and use READ_ONCE() to show we read these counters without surrounding synchronization. Interrupt moderation is best effort, and we do not really care of ultra precise counters. Signed-off-by: Eric Dumazet <edumazet@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller57-278/+581
udplite conflict is resolved by taking what 'net-next' did which removed the backlog receive method assignment, since it is no longer necessary. Two entries were added to the non-priv ethtool operations switch statement, one in 'net' and one in 'net-next, so simple overlapping changes. Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-26Merge branch 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linuxLinus Torvalds1-39/+25
Pull i2c fixes from Wolfram Sang: "Here is a revert and two bugfixes for the I2C designware driver. Please note that we are still hunting down a regression for the i2c-octeon driver. While there is a fix pending, we have unclear feedback from the testers currently. An rc8 would be quite helpful for this case" * 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: Revert "i2c: designware: do not disable adapter after transfer" i2c: designware: fix rx fifo depth tracking i2c: designware: report short transfers
2016-11-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds12-19/+28
Pull networking fixes from David Miller: 1) Fix leak in fsl/fman driver, from Dan Carpenter. 2) Call flow dissector initcall earlier than any networking driver can register and start to use it, from Eric Dumazet. 3) Some dup header fixes from Geliang Tang. 4) TIPC link monitoring compat fix from Jon Paul Maloy. 5) Link changes require EEE re-negotiation in bcm_sf2 driver, from Florian Fainelli. 6) Fix bogus handle ID passed into tfilter_notify_chain(), from Roman Mashak. 7) Fix dump size calculation in rtnl_calcit(), from Zhang Shengju. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits) tipc: resolve connection flow control compatibility problem mvpp2: use correct size for memset net/mlx5: drop duplicate header delay.h net: ieee802154: drop duplicate header delay.h ibmvnic: drop duplicate header seq_file.h fsl/fman: fix a leak in tgec_free() net: ethtool: don't require CAP_NET_ADMIN for ETHTOOL_GLINKSETTINGS tipc: improve sanity check for received domain records tipc: fix compatibility bug in link monitoring net: ethernet: mvneta: Remove IFF_UNICAST_FLT which is not implemented dwc_eth_qos: drop duplicate headers net sched filters: fix filter handle ID in tfilter_notify_chain() net: dsa: bcm_sf2: Ensure we re-negotiate EEE during after link change bnxt: do not busy-poll when link is down udplite: call proper backlog handlers ipv6: bump genid when the IFA_F_TENTATIVE flag is clear net/mlx4_en: Free netdev resources under state lock net: revert "net: l2tp: Treat NET_XMIT_CN as success in l2tp_eth_dev_xmit" rtnetlink: fix the wrong minimal dump size getting from rtnl_calcit() bnxt_en: Fix a VXLAN vs GENEVE issue ...
2016-11-26Merge branch 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimmLinus Torvalds2-3/+5
Pull libnvdimm fixes from Dan Williams: - Fix a crash that occurs at driver initialization if the memory region is already busy (request_mem_region() fails). - Fix a vma validation check that mistakenly allows a private device- dax mapping to be established. Device-dax explicitly forbids private mappings so it can guarantee a given fault granularity and backing memory type. Both of these fixes have soaked in -next and are tagged for -stable. * 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: device-dax: fail all private mapping attempts device-dax: check devm_nsio_enable() return value
2016-11-25mlxsw: spectrum: Add policers for trap groupsNogah Frankel1-2/+72
Configure policers and connect them to trap groups. While many trap groups share policer's configuration they don't share the actual policer because each trap group represents a different flow / protocol and we don't want one of them to be able to exceed its rate on behalf of another. For example, if STP and LLDP gets to send 128 packets/sec each, if we put them in one 256 packets/sec policer, one can send 200 packets while the other only 50. Note that IP2ME covers lots of flows, so it's limit is set to match the cpu ability to handle data. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: reg: Add QoS Policer Configuration RegisterNogah Frankel1-0/+141
The QPCR register is used to create and control policers. A policer can discard or change the color of packets that are trapped by a specific trap. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: resources: Add max cpu policers resourceNogah Frankel1-0/+2
Add a new resource to resources query: max cpu policers which tells us how many policers can be used to limit the data rate to the cpu port. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: Create a different trap group list for each deviceNogah Frankel3-34/+77
Trap groups can be used to control traps priority, both in terms of which trap "wins" if a packet matches two traps (priority) and in terms of packets from which trap group will be scheduled to the cpu first (tc). They can also be used to set rate limiters (policers) on them (will be added in the next patches). Currently, we support two trap groups. In Spectrum we want a better resolution, so every protocol / flow will have a different trap group, so we can control its parameters separately. Once the policers will be implemented, it will also allow us limit the rate of each protocol by itself. This patch change the trap group list to include: * the emad trap group, which is shared for all the devices. * Switchx2's trap groups, which are a copy of the current trap groups. * Spectrum's new trap groups, in order to match the above guidelines. (Switchib is using only the emad trap group, so it require no changes). This patch also includes new configuration for Spectrum's trap groups, with primary priority order within them. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: spectrum: Add BGP trapNogah Frankel2-0/+2
Add a trap for BGP protocol that was previously trapped by the generic trap for IP2ME. This trap will allow us to have better control (over priority and rate) of the traffic. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: Change trap groups settingNogah Frankel4-40/+92
Trap groups have many options which we currently set to default values. In the next patches we will use many of them with non-default values. Some of these options have no default value, so this patch sets them as params for the trap group set function. Others almost always use the same values, so the set function will use this default values. In the rare cases when they will need to be with other values, these values can be set directly (using the macros for fields in registers). Parameters without default value: TC - the traffic class for packets that hit this trap group. (old default is the max tc) priority - if one packet hits multiple trap groups, the group with the higher priority will "catch" it. (old default is 0) policer - limit rate policer (old default is disabled) Default parameters: swid - switch id, relevant for the emad trap only, ignored on Spectrum. (new default is 0) rdq - CPU receive descriptor queue (new default is identical to trap group id) Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: resources: Add max trap groups resourceNogah Frankel1-0/+2
Add the max number of trap groups to resource query. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Reviewed-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: core: Change emad trap group settingsNogah Frankel5-39/+39
Currently, the emad trap init was done in the core. In the future we will want to add some changes to the traps groups, according to device type. This commit create a driver function to create the trap group for the emad, so later it can be changed by devices. It also changes the emad registration to use the new generic functions. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: Add option to choose trap groupNogah Frankel4-21/+22
Currently, we set the trap group to pre-determined option, based on whether it is an rx or event trap. This commit adds a possibility to chose the trap group, so it can be set to different values in the following patches. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: Change trap set functionNogah Frankel5-44/+49
Change trap setting function so instead of determining the trap group by trap id, it gets it as a parameter (so later we can have different trap groups for Spectrum and Switchx2). Add "is_ctrl" parameter to the trap setting function. It control whether the trapped packets wait in a designated control buffer or in their default one. This parameter is ignored by Switchx2 and Switchib. Add these parameters to the traps array in Spectrum, Switchx2 and Switchib. Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-11-25mlxsw: switchib: Use generic listener struct for eventsNogah Frankel1-35/+27
Change the event handling in Switchib to be comptible with Spectrum and Switchx2. Use the generic listener struct for the events. Init and fini them by loop (and not by calling each event by its name). Signed-off-by: Nogah Frankel <nogahf@mellanox.com> Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.