| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Except for the usbuvc driver (with has an embedded media_device
struct on it), the other drivers have a pointer to media_device.
On those drivers, replace their own implementation for the core
one. That warrants that those subdev drivers will fill the
media_device info the same way.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
On USB drivers, the dev struct is usually filled with the USB
device. That would mean that the name of the driver specified
by media_device.dev.driver.name would be "usb", instead of the
name of the actual driver that created the media entity.
Add an optional field at the internal struct to allow drivers
to override the driver name.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The mutex lock at rc_register_device() was added by commit 08aeb7c9a42a
("[media] rc: add locking to fix register/show race").
It is meant to avoid race issues when trying to open a sysfs file while
the RC register didn't complete.
Adding a lock there causes troubles, as detected by the Kernel lock
debug instrumentation at the Kernel:
======================================================
[ INFO: possible circular locking dependency detected ]
4.5.0-rc3+ #46 Not tainted
-------------------------------------------------------
systemd-udevd/2681 is trying to acquire lock:
(s_active#171){++++.+}, at: [<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
but task is already holding lock:
(&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&dev->lock){+.+.+.}:
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff822de966>] mutex_lock_nested+0xb6/0x860
[<ffffffffa0721f2b>] show_protocols+0x3b/0x3f0 [rc_core]
[<ffffffff81cdaba5>] dev_attr_show+0x45/0xc0
[<ffffffff8171f1b3>] sysfs_kf_seq_show+0x203/0x3c0
[<ffffffff8171a6a1>] kernfs_seq_show+0x121/0x1b0
[<ffffffff81617c71>] seq_read+0x2f1/0x1160
[<ffffffff8171c911>] kernfs_fop_read+0x321/0x460
[<ffffffff815abc20>] __vfs_read+0xe0/0x3d0
[<ffffffff815ae90e>] vfs_read+0xde/0x2d0
[<ffffffff815b1d01>] SyS_read+0x111/0x230
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
-> #0 (s_active#171){++++.+}:
[<ffffffff81244f24>] __lock_acquire+0x4304/0x5990
[<ffffffff8124817d>] lock_acquire+0x13d/0x320
[<ffffffff81717d3a>] __kernfs_remove+0x58a/0x810
[<ffffffff8171a115>] kernfs_remove_by_name_ns+0x45/0xa0
[<ffffffff81721592>] remove_files.isra.0+0x72/0x190
[<ffffffff8172174b>] sysfs_remove_group+0x9b/0x150
[<ffffffff81721854>] sysfs_remove_groups+0x54/0xa0
[<ffffffff81cd97d0>] device_remove_attrs+0xb0/0x140
[<ffffffff81cdb27c>] device_del+0x38c/0x6b0
[<ffffffffa0724b8b>] rc_register_device+0x8cb/0x1450 [rc_core]
[<ffffffffa1326a7b>] dvb_usb_remote_init+0x66b/0x14d0 [dvb_usb]
[<ffffffffa1321c81>] dvb_usb_device_init+0xf21/0x1860 [dvb_usb]
[<ffffffffa13517dc>] dib0700_probe+0x14c/0x410 [dvb_usb_dib0700]
[<ffffffff81dbb1dd>] usb_probe_interface+0x45d/0x940
[<ffffffff81ce7e7a>] driver_probe_device+0x21a/0xc30
[<ffffffff81ce89b1>] __driver_attach+0x121/0x160
[<ffffffff81ce21bf>] bus_for_each_dev+0x11f/0x1a0
[<ffffffff81ce6cdd>] driver_attach+0x3d/0x50
[<ffffffff81ce5df9>] bus_add_driver+0x4c9/0x770
[<ffffffff81cea39c>] driver_register+0x18c/0x3b0
[<ffffffff81db6e98>] usb_register_driver+0x1f8/0x440
[<ffffffffa074001e>] dib0700_driver_init+0x1e/0x1000 [dvb_usb_dib0700]
[<ffffffff810021b1>] do_one_initcall+0x141/0x300
[<ffffffff8144d8eb>] do_init_module+0x1d0/0x5ad
[<ffffffff812f27b6>] load_module+0x6666/0x9ba0
[<ffffffff812f5fe8>] SyS_finit_module+0x108/0x130
[<ffffffff822e8636>] entry_SYSCALL_64_fastpath+0x16/0x76
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&dev->lock);
lock(s_active#171);
lock(&dev->lock);
lock(s_active#171);
*** DEADLOCK ***
3 locks held by systemd-udevd/2681:
#0: (&dev->mutex){......}, at: [<ffffffff81ce8933>] __driver_attach+0xa3/0x160
#1: (&dev->mutex){......}, at: [<ffffffff81ce8941>] __driver_attach+0xb1/0x160
#2: (&dev->lock){+.+.+.}, at: [<ffffffffa0724def>] rc_register_device+0xb2f/0x1450 [rc_core]
In this specific case, some error happened during device init,
causing IR to be disabled.
Let's fix it by adding a var that will tell when the device is
initialized. Any calls before that will return a -EINVAL.
That should prevent the race issues.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Instead of copying exactly the same code on all USB devices,
add an ancillary routine that will create and fill the
struct media_device with the values imported from the USB
device.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The tvp5150 decoder has different input connectors. The actual list of
HW inputs depends on the device version but all have at least these 3:
1) Composite0
2) Composite1
3) S-Video
and some variants have a 4th possible input connector:
4) Signal generator
The driver currently uses the .s_routing callback to switch the input
connector but since these are separate HW blocks, it's better to use
media entities to represent the input connectors and their source pads
linked with the decoder's sink pad.
This allows user-space to use the MEDIA_IOC_SETUP_LINK ioctl to choose
the input connector. For example using the media-ctl user-space tool:
$ media-ctl -r -l '"Composite0":0->"tvp5150 1-005c":0[1]'
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add a header file for the tvp5150 input connectors constants that
can be shared between the driver and Device Tree source files.
[mchehab@osg.samsung.com: rename tvp5150.h also at em28xx-cards.c]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Not all tvp5150 variants support the same, for example some have an
internal signal generator that can output a black screen.
So the device id and rom version have to be stored in the driver's
state to know what variant is a given device.
While being there, remove some redundant comments about the device
version since there is already calls to v4l2_info() with that info.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
If the parallel mbus configuration is not correct, the endpoint
device node isn't currently put again in the error path. Fix it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
V4L2 sub-devices might need to do initialization that depends on being
registered with a V4L2 device. As an example, sub-devices with Media
Controller support may need to register entities and create pad links.
Execute the registered_async callback after the sub-device has been
registered with the V4L2 device so the driver can do any needed init.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The module is used only as a library for now. Remove module init and exit
routines to show this.
While here, remove FSF snail address and attach EXPORT_SYMBOL() macros to
corresponding functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
v4l2_ctrl_add_ctrl() interface has no users since its introduction in
commit 0996517cf8ea ("V4L/DVB: v4l2: Add new control handling framework")
and its functionality is covered by v4l2_ctrl_new() and derivative
interfaces, so it is safe to remove the interface from the kernel.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This transmitter now supports configuring the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This receiver now supports reading the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This receiver now supports reading the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
HDMI and DisplayPort both support IT Content Type information that
tells the receiver what type of material the video is, graphics such
as from a PC desktop, Photo, Cinema or Game (low-latency).
This patch adds controls for receivers and transmitters to get/set
this information.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use the helper to enumerate and set DV timings instead of a custom code.
This will ease debugging too, as it is consistent with other drivers.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Remove an unnecassary cast in the argument to kfree.
Found using Coccinelle. The semantic patch used to find this is as follows:
//<smpl>
@@
type T;
expression *f;
@@
- kfree((T *)(f));
+ kfree(f);
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Auto-gain and auto-exposure clusters in the ov9650 driver have both a
size of 2, not 3 controls. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Instead of having lots of #ifdefs inside au0828-core due to
V4L2, move the dependencies to au0828-video.c. That allows
removing all those ifdefs, as au0828-video is only compiled if
CONFIG_VIDEO_AU0828_V4L2.
This fixes the following warnings reported by Kbuild test
with a random config with au0828 enabled, but V4L2 is disabled.
All warnings (new ones prefixed by >>):
drivers/media/usb/au0828/au0828-core.c: In function 'au0828_usb_probe':
>> drivers/media/usb/au0828/au0828-core.c:463:1: warning: label 'done' defined but not used [-Wunused-label]
done:
^
drivers/media/usb/au0828/au0828-core.c: At top level:
drivers/media/usb/au0828/au0828-core.c:250:12: warning: 'au0828_create_media_graph' defined but not used [-Wunused-function]
static int au0828_create_media_graph(struct au0828_dev *dev)
^
Tested with a WinTV HVR 950Q (USB ID: 2040:7200)
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
It doesn't make sense to try to create the analog TV graph,
if the device fails to register at V4L2, or if it doesn't have
V4L2 support.
Thanks to Shuah for pointing this issue.
Reported-by: Shuah Khan <shuahkh@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Register saa7134 at the media controller core and provide
support for both analog TV and DVB.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Instead of copyping the same code on all PCI devices that
would have a media controller, add a core ancillary routine.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The saa7134_input.tv field was used to indicate if an input had
a RF signal for TV input. This is not needed anymore, as the input
type can be checked directly by the driver.
Also, due to a past bug when setting the TV standard at the
demod, all inputs should have this field set, with is wrong.
This reduces the size of the saa7134_boards by about 8KB,
on i386 (and probably twice on 64 bits), with is a nice
colateral effect:
text data bss dec hex filename
241047 136831 66356 444234 6c74a drivers/media/pci/saa7134/saa7134.o.old
240851 128895 66292 436038 6a746 drivers/media/pci/saa7134/saa7134.o
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
It doesn't make any sense to only update the TV standard for TV,
as composite and S-Video inputs also need it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Currently, the saa7134 driver is hardcoding input names on each
board entry. More modern drivers define, instead, an enum for each
input type.
While the current logic works, it adds extra complexity at the driver,
as it needs to discover the type of the input using some euristics.
Instead, let's standardize the input types and use a type, instead of
a name on all places.
That will allow further patches to properly report the input type
via VIDIOC_G_INPUT and to remove an extra field from the struct to
identify if the input is for TV.
Please notice that several boards define an input for receiving composite
signals via a S-Video connector. The name of such input was inconsistent,
so this patch cleans it and make it to be properly reported the
same way for all boards.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Allow devices to pass an optional argument to register the DVB
driver at the media controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Now that the core has a function to create the media graph,
we can get rid of the specialized code at em28xx.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The em28xx_v4l2_create_media_graph() is almost generic enough to
be at the core, as an ancillary function. Make it even more generic,
by getting rid of em28xx-specific code, relying only at the
media_device, in order to discover all entities found on PC-customer's
hardware and add it at the V4L2 core.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
|
|
Pull ARM SoC fixes from Olof Johansson:
"The first real batch of fixes for this release cycle, so there are a
few more than usual.
Most of these are fixes and tweaks to board support (DT bugfixes,
etc). I've also picked up a couple of small cleanups that seemed
innocent enough that there was little reason to wait (const/
__initconst and Kconfig deps).
Quite a bit of the changes on OMAP were due to fixes to no longer
write to rodata from assembly when ARM_KERNMEM_PERMS was enabled, but
there were also other fixes.
Kirkwood had a bunch of gpio fixes for some boards. OMAP had RTC
fixes on OMAP5, and Nomadik had changes to MMC parameters in DT.
All in all, mostly the usual mix of various fixes"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (46 commits)
ARM: multi_v7_defconfig: enable DW_WATCHDOG
ARM: nomadik: fix up SD/MMC DT settings
ARM64: tegra: Add chosen node for tegra132 norrin
ARM: realview: use "depends on" instead of "if" after prompt
ARM: tango: use "depends on" instead of "if" after prompt
ARM: tango: use const and __initconst for smp_operations
ARM: realview: use const and __initconst for smp_operations
bus: uniphier-system-bus: revive tristate prompt
arm64: dts: Add missing DMA Abort interrupt to Juno
bus: vexpress-config: Add missing of_node_put
ARM: dts: am57xx: sbc-am57x: correct Eth PHY settings
ARM: dts: am57xx: cl-som-am57x: fix CPSW EMAC pinmux
ARM: dts: am57xx: sbc-am57x: fix UART3 pinmux
ARM: dts: am57xx: cl-som-am57x: update SPI Flash frequency
ARM: dts: am57xx: cl-som-am57x: set HOST mode for USB2
ARM: dts: am57xx: sbc-am57x: fix SB-SOM EEPROM I2C address
ARM: dts: LogicPD Torpedo: Revert Duplicative Entries
ARM: dts: am437x: pixcir_tangoc: use correct flags for irq types
ARM: dts: am4372: fix irq type for arm twd and global timer
ARM: dts: at91: sama5d4 xplained: fix phy0 IRQ type
...
|
|
Pull mailbox fixes from Jassi Brar:
- fix getting element from the pcc-channels array by simply indexing
into it
- prevent building mailbox-test driver for archs that don't have IOMEM
* 'mailbox-devel' of git://git.linaro.org/landing-teams/working/fujitsu/integration:
mailbox: Fix dependencies for !HAS_IOMEM archs
mailbox: pcc: fix channel calculation in get_pcc_channel()
|
|
Pull USB fixes from Greg KH:
"Here are some USB fixes for 4.5-rc3.
The usual, xhci fixes for reported issues, combined with some small
gadget driver fixes, and a MAINTAINERS file update. All have been in
linux-next with no reported issues"
* tag 'usb-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
xhci: harden xhci_find_next_ext_cap against device removal
xhci: Fix list corruption in urb dequeue at host removal
usb: host: xhci-plat: fix NULL pointer in probe for device tree case
usb: xhci-mtk: fix AHB bus hang up caused by roothubs polling
usb: xhci-mtk: fix bpkts value of LS/HS periodic eps not behind TT
usb: xhci: apply XHCI_PME_STUCK_QUIRK to Intel Broxton-M platforms
usb: xhci: set SSIC port unused only if xhci_suspend succeeds
usb: xhci: add a quirk bit for ssic port unused
usb: xhci: handle both SSIC ports in PME stuck quirk
usb: dwc3: gadget: set the OTG flag in dwc3 gadget driver.
Revert "xhci: don't finish a TD if we get a short-transfer event mid TD"
MAINTAINERS: fix my email address
usb: dwc2: Fix probe problem on bcm2835
Revert "usb: dwc2: Move reset into dwc2_get_hwparams()"
usb: musb: ux500: Fix NULL pointer dereference at system PM
usb: phy: mxs: declare variable with initialized value
usb: phy: msm: fix error handling in probe.
|
|
Pull staging and IIO driver fixes from Greg KH:
"Here are some IIO and staging driver fixes for 4.5-rc3.
All of them, except one, are for IIO drivers, and one is for a speakup
driver fix caused by some earlier patches, to resolve a reported build
failure"
* tag 'staging-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Staging: speakup: Fix allyesconfig build on mn10300
iio: dht11: Use boottime
iio: ade7753: avoid uninitialized data
iio: pressure: mpl115: fix temperature offset sign
iio: imu: Fix dependencies for !HAS_IOMEM archs
staging: iio: Fix dependencies for !HAS_IOMEM archs
iio: adc: Fix dependencies for !HAS_IOMEM archs
iio: inkern: fix a NULL dereference on error
iio:adc:ti_am335x_adc Fix buffered mode by identifying as software buffer.
iio: light: acpi-als: Report data as processed
iio: dac: mcp4725: set iio name property in sysfs
iio: add HAS_IOMEM dependency to VF610_ADC
iio: add IIO_TRIGGER dependency to STK8BA50
iio: proximity: lidar: correct return value
iio-light: Use a signed return type for ltr501_match_samp_freq()
|
|
Pull drm fixes from Dave Airlie:
"Fixes all over the place:
- amdkfd: two static checker fixes
- mst: a bunch of static checker and spec/hw interaction fixes
- amdgpu: fix Iceland hw properly, and some fiji bugs, along with
some write-combining fixes.
- exynos: some regression fixes
- adv7511: fix some EDID reading issues"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (38 commits)
drm/dp/mst: deallocate payload on port destruction
drm/dp/mst: Reverse order of MST enable and clearing VC payload table.
drm/dp/mst: move GUID storage from mgr, port to only mst branch
drm/dp/mst: change MST detection scheme
drm/dp/mst: Calculate MST PBN with 31.32 fixed point
drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil
drm/mst: Add range check for max_payloads during init
drm/mst: Don't ignore the MST PBN self-test result
drm: fix missing reference counting decrease
drm/amdgpu: disable uvd and vce clockgating on Fiji
drm/amdgpu: remove exp hardware support from iceland
drm/amdgpu: load MEC ucode manually on iceland
drm/amdgpu: don't load MEC2 on topaz
drm/amdgpu: drop topaz support from gmc8 module
drm/amdgpu: pull topaz gmc bits into gmc_v7
drm/amdgpu: The VI specific EXE bit should only apply to GMC v8.0 above
drm/amdgpu: iceland use CI based MC IP
drm/amdgpu: move gmc7 support out of CIK dependency
drm/amdgpu/gfx7: enable cp inst/reg error interrupts
drm/amdgpu/gfx8: enable cp inst/reg error interrupts
...
|
|
Pull power management and ACPI fixes from Rafael Wysocki:
"These are: a fix for a recently introduced false-positive warnings
about PM domain pointers being changed inappropriately (harmless but
annoying), an MCH size workaround quirk for one more platform, a
compiler warning fix (generic power domains framework), an ACPI LPSS
(Intel SoCs) driver fixup and a cleanup of the ACPI CPPC core code.
Specifics:
- PM core fix to avoid false-positive warnings generated when the
pm_domain field is cleared for a device that appears to be bound to
a driver (Rafael Wysocki).
- New MCH size workaround quirk for Intel Haswell-ULT (Josh Boyer).
- Fix for an "unused function" compiler warning in the generic power
domains framework (Ulf Hansson).
- Fixup for the ACPI driver for Intel SoCs (acpi-lpss) to set the PM
domain pointer of a device properly in one place that was
overlooked by a recent PM core update (Andy Shevchenko).
- Removal of a redundant function declaration in the ACPI CPPC core
code (Timur Tabi)"
* tag 'pm+acpi-4.5-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM: Avoid false-positive warnings in dev_pm_domain_set()
PM / Domains: Silence compiler warning for an unused function
ACPI / CPPC: remove redundant mbox_send_message() declaration
ACPI / LPSS: set PM domain via helper setter
PNP: Add Haswell-ULT to Intel MCH size workaround
|
|
* pm-core:
PM: Avoid false-positive warnings in dev_pm_domain_set()
ACPI / LPSS: set PM domain via helper setter
* pm-domains:
PM / Domains: Silence compiler warning for an unused function
|
|
Pull media fixes from Mauro Carvalho Chehab:
- vb2: fix a vb2_thread regression and DVB read() breakages
- vsp1: fix compilation and links creation
- s5k6a3: Fix VIDIOC_SUBDEV_G_FMT ioctl for TRY format
- exynos4-is: fix a build issue, format negotiation and sensor detection
- Fix a regression with pvrusb2 and ir-kbd-i2c
- atmel-isi: fix debug message which only show the first format
- tda1004x: fix a tuning bug if G_PROPERTY is called too early
- saa7134-alsa: fix a bug at device unbinding/driver removal
- Fix build of one driver if !HAS_DMA
- soc_camera: cleanup control device on async_unbind
* tag 'media/v4.5-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] saa7134-alsa: Only frees registered sound cards
[media] vb2-core: call threadio->fnc() if !VB2_BUF_STATE_ERROR
[media] vb2: fix nasty vb2_thread regression
[media] tda1004x: only update the frontend properties if locked
[media] media: i2c: Don't export ir-kbd-i2c module alias
[media] exynos4-is: make VIDEO_SAMSUNG_EXYNOS4_IS tristate
[media] media: Kconfig: add dependency of HAS_DMA
[media] exynos4-is: Wait for 100us before opening sensor
[media] exynos4-is: Open shouldn't fail when sensor entity is not linked
[media] s5k6a3: Fix VIDIOC_SUBDEV_G_FMT ioctl for TRY format
[media] exynos4-is: fix a format string bug
[media] drivers/media: vsp1_video: fix compile error
[media] atmel-isi: fix debug message which only show the first format
[media] soc_camera: cleanup control device on async_unbind
[media] v4l: vsp1: Fix wrong entities links creation
|
|
Pull watchdog fixes from Wim Van Sebroeck:
"This fixes several Kconfig dependencies, a compilation warning in
pcwd_usb, a failure to abort the sp805 wdt after a ping and the
max63xx wdt's MODULE_LICENSE"
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: Fix dependencies for !HAS_IOMEM archs
watchdog: imgdpc: select WATCHDOG_CORE
watchdog: tango: rename ARCH_TANGOX to ARCH_TANGO
watchdog: pcwd_usb: fix compilation warning
watchdog: sp805: ping fails to abort wdt reset
watchdog: max63xx: make module's license marker match the header
|
|
displayport multistream fixes from AMD.
* 'drm-fixes-mst' of git://people.freedesktop.org/~airlied/linux:
drm/dp/mst: deallocate payload on port destruction
drm/dp/mst: Reverse order of MST enable and clearing VC payload table.
drm/dp/mst: move GUID storage from mgr, port to only mst branch
drm/dp/mst: change MST detection scheme
drm/dp/mst: Calculate MST PBN with 31.32 fixed point
drm: Add drm_fixp_from_fraction and drm_fixp2int_ceil
drm/mst: Add range check for max_payloads during init
drm/mst: Don't ignore the MST PBN self-test result
drm: fix missing reference counting decrease
|
|
This is needed to properly deallocate port payload
after downstream branch get unplugged.
In order to do this unplugged MST topology should
be preserved, to find first alive port on path to
unplugged MST topology, and send payload deallocation
request to branch device of found port.
For this mstb and port kref's are used in reversed
order to track when port and branch memory could be
freed.
Added additional functions to find appropriate mstb
as described above.
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
On DELL U3014 if you clear the table before enabling MST it sometimes
hangs the receiver.
Signed-off-by: Andrey Grodzovsky <Andrey.Grodzovsky@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Previous implementation does not handle case below: boot up one MST branch
to DP connector of ASIC. After boot up, hot plug 2nd MST branch to DP output
of 1st MST, GUID is not created for 2nd MST branch. When downstream port of
2nd MST branch send upstream request, it fails because 2nd MST branch GUID
is not available.
New Implementation: only create GUID for MST branch and save it within Branch.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
1. Get edid for all connected MST displays, not only on logical ports,
in the same thread as MST topology detection is done:
There are displays that have branches inside w/o logical ports.
So in case another SST display connected downstream system can
end-up in situation when 3 DOWN requests sent: two for
‘remote i2c read’ and one for ‘enum path resources’, making slots full.
2. Call notification callback in one place in the end of topology discovery/update:
This is done to reduce number of events sent to userspace in case complex
topology discovery is going, adding multiple number of connectors;
3. Remove notification callback call from short pulse interrupt processing function:
This is done in order not to block interrupt processing function, in case any
MST request will be made from it. Notification will be send from topology
discovery/update work item.
Signed-off-by: Mykola Lysenko <Mykola.Lysenko@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Cc: stable@vger.kernel.org
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Our PBN value overflows the 20 bits integer part of the 20.12
fixed point. We need to use 31.32 fixed point to avoid this.
This happens with display clocks larger than 293122 (at 24 bpp),
which we see with the Sharp (and similar) 4k tiled displays.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: stable@vger.kernel.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
max_payload is limited by the space we have in
drm_dp_mst_topology_mgr::vcpi_mask,payload_mask. We need to track
max_payloads+1 IDs in these masks, see drm_dp_mst_assign_payload_id().
Add a sanity check for this.
Caught by coverity.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Otherwise this call would have no effect.
Caught by Coverity.
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: David Weinehall <david.weinehall@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
In drm_dp_mst_allocate_vcpi, it returns true in two paths,
but in one path, there is no reference couting decrease.
Signed-off-by: Insu Yun <wuninsu@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
- fix and enable iceland/topaz support
- handle WC on platforms that don't support it
* 'drm-fixes-4.5' of git://people.freedesktop.org/~agd5f/linux:
drm/amdgpu: disable uvd and vce clockgating on Fiji
drm/amdgpu: remove exp hardware support from iceland
drm/amdgpu: load MEC ucode manually on iceland
drm/amdgpu: don't load MEC2 on topaz
drm/amdgpu: drop topaz support from gmc8 module
drm/amdgpu: pull topaz gmc bits into gmc_v7
drm/amdgpu: The VI specific EXE bit should only apply to GMC v8.0 above
drm/amdgpu: iceland use CI based MC IP
drm/amdgpu: move gmc7 support out of CIK dependency
drm/amdgpu/gfx7: enable cp inst/reg error interrupts
drm/amdgpu/gfx8: enable cp inst/reg error interrupts
drm/amdgpu: mask out WC from BO on unsupported arches
drm/radeon: mask out WC from BO on unsupported arches
drm: add helper to check for wc memory support
drm/amdgpu: no need to load MC firmware on fiji
|
|
two static checker fixes.
* tag 'drm-amdkfd-fixes-2016-01-28' of git://people.freedesktop.org/~gabbayo/linux:
drm/amdkfd: Remove unnecessary cast in kfree
drm/amdgpu: fix non-ANSI declaration of amdgpu_amdkfd_gfx_*_get_functions()
|
|
Just regression fixes.
- Fix build warning and error without PM configuration
- Fix no display issue on Snow board reported by Michal Suchanek,
http://www.spinics.net/lists/dri-devel/msg99473.html
* 'exynos-drm-fixes' of git://git.kernel.org:/pub/scm/linux/kernel/git/daeinki/drm-exynos:
drm/exynos: dp: Fix panel and bridge lookup logic
drm: exynos: make PM functions as __maybe_unused
drm/exynos: fix building without CONFIG_PM_SLEEP
|
Mauro Carvalho Chehab
Javier Martinez Canillas
Andy Shevchenko
Vladimir Zapolskiy
Hans Verkuil
Jean-Michel Hautbois
Amitoj Kaur Chawla
Guennadi Liakhovetski
Linus Torvalds
Rafael J. Wysocki
Dave Airlie
Mykola Lysenko
Andrey Grodzovsky
Hersen Wu
Harry Wentland
Imre Deak
Insu Yun