| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The size is always equal to 1 page so let's use this. Later on this will
be used for other checks which use page shifts to check the granularity
of access.
This should cause no behavioral change.
Cc: stable@vger.kernel.org # v4.12+
Reviewed-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Alex Williamson <alex.williamson@redhat.com>
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This driver can spam the kernel log with multiple messages of:
net eth0: eth0: allmulti set
Usually 4 or 8 at a time (probably because of using ConnMan).
This message doesn't seem useful, so let's demote it from dev_info()
to dev_dbg().
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
octeon_mgmt driver doesn't drop RX frames that are 1-4 bytes bigger than
MTU set for the corresponding interface. The problem is in the
AGL_GMX_RX0/1_FRM_MAX register setting, which should not account for VLAN
tagging.
According to Octeon HW manual:
"For tagged frames, MAX increases by four bytes for each VLAN found up to a
maximum of two VLANs, or MAX + 8 bytes."
OCTEON_FRAME_HEADER_LEN "define" is fine for ring buffer management, but
should not be used for AGL_GMX_RX0/1_FRM_MAX.
The problem could be easily reproduced using "ping" command. If affected
system has default MTU 1500, other host (having MTU >= 1504) can
successfully "ping" the affected system with payload size 1473-1476,
resulting in IP packets of size 1501-1504 accepted by the mgmt driver.
Fixed system still accepts IP packets of 1500 bytes even with VLAN tagging,
because the limits are lifted in HW as expected, for every VLAN tag.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
[why] dp hbr2 eye diagram pattern for raven asic is not stabled.
workaround is to use tp4 pattern. But this should not be
applied to asic before raven.
[how] add new bool varilable in asic caps. for raven asic,
use the workaround. for carrizo, vega, do not use workaround.
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Fixes: 2c773de2 (drm/amdgpu: defer test IBs on the rings at boot (V3))
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Avoid excuting set_feature command if there is no supported bit in
Optional Asynchronous Events Supported (OAES).
Fixes: c0561f82 ("nvme: submit AEN event configuration on startup")
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Weiping Zhang <zhangweiping@didichuxing.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If the controller supports effects and goes down during the passthru admin
command we will deadlock during namespace revalidation.
[ 363.488275] INFO: task kworker/u16:5:231 blocked for more than 120 seconds.
[ 363.488290] Not tainted 4.17.0+ #2
[ 363.488296] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 363.488303] kworker/u16:5 D 0 231 2 0x80000000
[ 363.488331] Workqueue: nvme-reset-wq nvme_reset_work [nvme]
[ 363.488338] Call Trace:
[ 363.488385] schedule+0x75/0x190
[ 363.488396] rwsem_down_read_failed+0x1c3/0x2f0
[ 363.488481] call_rwsem_down_read_failed+0x14/0x30
[ 363.488504] down_read+0x1d/0x80
[ 363.488523] nvme_stop_queues+0x1e/0xa0 [nvme_core]
[ 363.488536] nvme_dev_disable+0xae4/0x1620 [nvme]
[ 363.488614] nvme_reset_work+0xd1e/0x49d9 [nvme]
[ 363.488911] process_one_work+0x81a/0x1400
[ 363.488934] worker_thread+0x87/0xe80
[ 363.488955] kthread+0x2db/0x390
[ 363.488977] ret_from_fork+0x35/0x40
Fixes: 84fef62d135b6 ("nvme: check admin passthru command effects")
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Reviewed-by: Keith Busch <keith.busch@linux.intel.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch has fix for TX timeout while running bi-directional
traffic with 100 Mbps using 5762.
Signed-off-by: Sanjeev Bansal <sanjeevb.bansal@broadcom.com>
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Siva Reddy Kallam <siva.kallam@broadcom.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Testing has uncovered a failure case that is not handled properly. In the
event that a login fails and we are not able to recover on the spot, we
return 0 from do_reset, preventing any error recovery code from being
triggered. Additionally, the state is set to "probed" meaning that when we
are able to trigger the error recovery, the driver always comes up in the
probed state. To handle the case properly, we need to return a failure code
here and set the adapter state to the state that we entered the reset in
indicating the state that we would like to come out of the recovery reset
in.
Signed-off-by: John Allen <jallen@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The skb size calculation in lan78xx_tx_bh is in race with the start_xmit,
which could lead to rare kernel oopses. So protect the whole skb walk with
a spin lock. As a benefit we can unlink the skb directly.
This patch was tested on Raspberry Pi 3B+
Link: https://github.com/raspberrypi/linux/issues/2608
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Floris Bos <bos@je-eigen-domein.nl>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new rx packet arrives, the rx path will decide whether to reuse
the remainder of the page or not according to one of the below conditions:
1. frag_info->frag_stride == PAGE_SIZE / 2
2. frags->page_offset + frag_info->frag_size > PAGE_SIZE;
The first condition is no met for when XDP is set.
For XDP, page_offset is always set to priv->rx_headroom which is
XDP_PACKET_HEADROOM and frag_info->frag_size is around mtu size + some
padding, still the 2nd release condition will hold since
XDP_PACKET_HEADROOM + 1536 < PAGE_SIZE, as a result the page will not
be released and will be _wrongly_ reused for next free rx descriptor.
In XDP there is an assumption to have a page per packet and reuse can
break such assumption and might cause packet data corruptions.
Fix this by adding an extra condition (!priv->rx_headroom) to the 2nd
case to avoid page reuse when XDP is set, since rx_headroom is set to 0
for non XDP setup and set to XDP_PACKET_HEADROOM for XDP setup.
No additional cache line is required for the new condition.
Fixes: 34db548bfb95 ("mlx4: add page recycling in receive path")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Suggested-by: Martin KaFai Lau <kafai@fb.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netvsc device may need to fallback to running in single queue
mode if host side only wants to support single queue.
Recent change for handling mtu broke this in setup logic.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 3ffe64f1a641 ("hv_netvsc: split sub-channel setup into async and sync")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a device failover, there may be latency between the loss
of the current backing device and a notification from firmware that
a failover has occurred. This latency can result in a large amount of
error printouts as firmware returns outgoing traffic with a generic
error code. These are not necessarily errors in this case as the
firmware is busy swapping in a new backing adapter and is not ready
to send packets yet. This patch reclassifies those error codes as
warnings with an explanation that a failover may be pending. All
other return codes will be considered errors.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch remove the following documentation warning
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c:103: warning: Excess function parameter 'priv' description in 'stmmac_axi_setup'
It was introduced in commit afea03656add7 ("stmmac: rework DMA bus setting and introduce new platform AXI structure")
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fix a typo in the word Describe
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On XDP_TX we need to free up the frame only when tun_xdp_tx() returns a
negative value. A positive value indicates that the packet is
successfully enqueued to the ptr_ring, so freeing the page causes
use-after-free.
Fixes: 735fc4054b3a ("xdp: change ndo_xdp_xmit API to support bulking")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull pin control fixes from Linus Walleij:
- A slew of driver fixes for Mediatek mt7622
- Fix a direction inversion bug in the Ingenic driver
- Fix unsupported drive strength setting on the PFC r8a77970
- Off by one and NULL dereference fixes in the NSP driver
* tag 'pinctrl-v4.18-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: nsp: Fix potential NULL dereference
pinctrl: nsp: off by ones in nsp_pinmux_enable()
pinctrl: sh-pfc: r8a77970: remove SH_PFC_PIN_CFG_DRIVE_STRENGTH flag
pinctrl: ingenic: Fix inverted direction for < JZ4770
pinctrl: mt7622: fix a kernel panic when gpio-hog is being applied
pinctrl: mt7622: stop using the deprecated pinctrl_add_gpio_range
pinctrl: mt7622: fix that pinctrl_claim_hogs cannot work
pinctrl: mt7622: fix initialization sequence between eint and gpiochip
pinctrl: mt7622: fix error path on failing at groups building
|
|
Pull drm fixes from Dave Airlie:
- two AGP fixes in here
- a bunch of mostly amdgpu fixes
- sun4i build fix
- two armada fixes
- some tegra fixes
- one i915 core and one i915 gvt fix
* tag 'drm-fixes-2018-07-16-1' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu/pp/smu7: use a local variable for toc indexing
amd/dc/dce100: On dce100, set clocks to 0 on suspend
drm/amd/display: Convert 10kHz clks from PPLib into kHz for Vega
drm/amdgpu: Verify root PD is mapped into kernel address space (v4)
drm/amd/display: fix invalid function table override
drm/amdgpu: Reserve VM root shared fence slot for command submission (v3)
Revert "drm/amd/display: Don't return ddc result and read_bytes in same return value"
char: amd64-agp: Use 64-bit arithmetic instead of 32-bit
char: agp: Change return type to vm_fault_t
drm/i915: Fix hotplug irq ack on i965/g4x
drm/armada: fix irq handling
drm/armada: fix colorkey mode property
drm/tegra: Fix comparison operator for buffer size
gpu: host1x: Check whether size of unpin isn't 0
gpu: host1x: Skip IOMMU initialization if firewall is enabled
drm/sun4i: link in front-end code if needed
drm/i915/gvt: update vreg on inhibit context lri command
|
|
A comment in the review of the patch adding the phandle cache said that
the cache would have to be updated when modules are applied and removed.
This patch implements the cache updates.
Fixes: 0b3ce78e90fc ("of: cache phandle nodes to reduce cost of of_find_node_by_phandle()")
Reported-by: Alan Tull <atull@kernel.org>
Suggested-by: Alan Tull <atull@kernel.org>
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Currently nouveau doesn't actually expose the state debugfs file that's
usually provided for any modesetting driver that supports atomic, even
if nouveau is loaded with atomic=1. This is due to the fact that the
standard debugfs files that DRM creates for atomic drivers is called
when drm_get_pci_dev() is called from nouveau_drm.c. This happens well
before we've initialized the display core, which is currently
responsible for setting the DRIVER_ATOMIC cap.
So, move the atomic option into nouveau_drm.c and just add the
DRIVER_ATOMIC cap whenever it's enabled on the kernel commandline. This
shouldn't cause any actual issues, as the atomic ioctl will still fail
as expected even if the display core doesn't disable it until later in
the init sequence. This also provides the added benefit of being able to
use the state debugfs file to check the current display state even if
clients aren't allowed to modify it through anything other than the
legacy ioctls.
Additionally, disable the DRIVER_ATOMIC cap in nv04's display core, as
this was already disabled there previously.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
This both uses the legacy modesetting structures in a racy manner, and
additionally also doesn't even check the right variable (enabled != the
CRTC is actually turned on for atomic).
This fixes issues on my P50 regarding the dedicated GPU not entering
runtime suspend.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
A CRTC being enabled doesn't mean it's on! It doesn't even necessarily
mean it's being used. This fixes runtime PM leaks on the P50 I've got
next to me.
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
When MST and atomic were introduced to nouveau, another structure that
could contain a drm_connector embedded within it was introduced; struct
nv50_mstc. This meant that we no longer would be able to simply loop
through our connector list and assume that nouveau_connector() would
return a proper pointer for each connector, since the assertion that
all connectors coming from nouveau have a full nouveau_connector struct
became invalid.
Unfortunately, none of the actual code that looped through connectors
ever got updated, which means that we've been causing invalid memory
accesses for quite a while now.
An example that was caught by KASAN:
[ 201.038698] ==================================================================
[ 201.038792] BUG: KASAN: slab-out-of-bounds in nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038797] Read of size 4 at addr ffff88076738c650 by task kworker/0:3/718
[ 201.038800]
[ 201.038822] CPU: 0 PID: 718 Comm: kworker/0:3 Tainted: G O 4.18.0-rc4Lyude-Test+ #1
[ 201.038825] Hardware name: LENOVO 20EQS64N0B/20EQS64N0B, BIOS N1EET78W (1.51 ) 05/18/2018
[ 201.038882] Workqueue: events nouveau_display_hpd_work [nouveau]
[ 201.038887] Call Trace:
[ 201.038894] dump_stack+0xa4/0xfd
[ 201.038900] print_address_description+0x71/0x239
[ 201.038929] ? nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038935] kasan_report.cold.6+0x242/0x2fe
[ 201.038942] __asan_report_load4_noabort+0x19/0x20
[ 201.038970] nvif_notify_get+0x190/0x1a0 [nouveau]
[ 201.038998] ? nvif_notify_put+0x1f0/0x1f0 [nouveau]
[ 201.039003] ? kmsg_dump_rewind_nolock+0xe4/0xe4
[ 201.039049] nouveau_display_init.cold.12+0x34/0x39 [nouveau]
[ 201.039089] ? nouveau_user_framebuffer_create+0x120/0x120 [nouveau]
[ 201.039133] nouveau_display_resume+0x5c0/0x810 [nouveau]
[ 201.039173] ? nvkm_client_ioctl+0x20/0x20 [nouveau]
[ 201.039215] nouveau_do_resume+0x19f/0x570 [nouveau]
[ 201.039256] nouveau_pmops_runtime_resume+0xd8/0x2a0 [nouveau]
[ 201.039264] pci_pm_runtime_resume+0x130/0x250
[ 201.039269] ? pci_restore_standard_config+0x70/0x70
[ 201.039275] __rpm_callback+0x1f2/0x5d0
[ 201.039279] ? rpm_resume+0x560/0x18a0
[ 201.039283] ? pci_restore_standard_config+0x70/0x70
[ 201.039287] ? pci_restore_standard_config+0x70/0x70
[ 201.039291] ? pci_restore_standard_config+0x70/0x70
[ 201.039296] rpm_callback+0x175/0x210
[ 201.039300] ? pci_restore_standard_config+0x70/0x70
[ 201.039305] rpm_resume+0xcc3/0x18a0
[ 201.039312] ? rpm_callback+0x210/0x210
[ 201.039317] ? __pm_runtime_resume+0x9e/0x100
[ 201.039322] ? kasan_check_write+0x14/0x20
[ 201.039326] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039333] __pm_runtime_resume+0xac/0x100
[ 201.039374] nouveau_display_hpd_work+0x67/0x1f0 [nouveau]
[ 201.039380] process_one_work+0x7a0/0x14d0
[ 201.039388] ? cancel_delayed_work_sync+0x20/0x20
[ 201.039392] ? lock_acquire+0x113/0x310
[ 201.039398] ? kasan_check_write+0x14/0x20
[ 201.039402] ? do_raw_spin_lock+0xc2/0x1c0
[ 201.039409] worker_thread+0x86/0xb50
[ 201.039418] kthread+0x2e9/0x3a0
[ 201.039422] ? process_one_work+0x14d0/0x14d0
[ 201.039426] ? kthread_create_worker_on_cpu+0xc0/0xc0
[ 201.039431] ret_from_fork+0x3a/0x50
[ 201.039441]
[ 201.039444] Allocated by task 79:
[ 201.039449] save_stack+0x43/0xd0
[ 201.039452] kasan_kmalloc+0xc4/0xe0
[ 201.039456] kmem_cache_alloc_trace+0x10a/0x260
[ 201.039494] nv50_mstm_add_connector+0x9a/0x340 [nouveau]
[ 201.039504] drm_dp_add_port+0xff5/0x1fc0 [drm_kms_helper]
[ 201.039511] drm_dp_send_link_address+0x4a7/0x740 [drm_kms_helper]
[ 201.039518] drm_dp_check_and_send_link_address+0x1a7/0x210 [drm_kms_helper]
[ 201.039525] drm_dp_mst_link_probe_work+0x71/0xb0 [drm_kms_helper]
[ 201.039529] process_one_work+0x7a0/0x14d0
[ 201.039533] worker_thread+0x86/0xb50
[ 201.039537] kthread+0x2e9/0x3a0
[ 201.039541] ret_from_fork+0x3a/0x50
[ 201.039543]
[ 201.039546] Freed by task 0:
[ 201.039549] (stack is not available)
[ 201.039551]
[ 201.039555] The buggy address belongs to the object at ffff88076738c1a8
which belongs to the cache kmalloc-2048 of size 2048
[ 201.039559] The buggy address is located 1192 bytes inside of
2048-byte region [ffff88076738c1a8, ffff88076738c9a8)
[ 201.039563] The buggy address belongs to the page:
[ 201.039567] page:ffffea001d9ce200 count:1 mapcount:0 mapping:ffff88084000d0c0 index:0x0 compound_mapcount: 0
[ 201.039573] flags: 0x8000000000008100(slab|head)
[ 201.039578] raw: 8000000000008100 ffffea001da3be08 ffffea001da25a08 ffff88084000d0c0
[ 201.039582] raw: 0000000000000000 00000000000d000d 00000001ffffffff 0000000000000000
[ 201.039585] page dumped because: kasan: bad access detected
[ 201.039588]
[ 201.039591] Memory state around the buggy address:
[ 201.039594] ffff88076738c500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039598] ffff88076738c580: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 201.039601] >ffff88076738c600: 00 00 00 00 00 00 00 00 00 00 fc fc fc fc fc fc
[ 201.039604] ^
[ 201.039607] ffff88076738c680: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039611] ffff88076738c700: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 201.039613] ==================================================================
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Every codepath in nouveau that loops through the connector list
currently does so using the old method, which is prone to race
conditions from MST connectors being created and destroyed. This has
been causing a multitude of problems, including memory corruption from
trying to access connectors that have already been freed!
Signed-off-by: Lyude Paul <lyude@redhat.com>
Cc: stable@vger.kernel.org
Cc: Karol Herbst <karolherbst@gmail.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The bo array has req->nr_buffers elements so the > should be >= so we
don't read beyond the end of the array.
Fixes: a1606a9596e5 ("drm/nouveau: new gem pushbuf interface, bump to 0.0.16")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
It was possible for this to be skipped when shutting down MST streams, and
leaving the core channel interlocked with a wndw channel update that never
happens - leading to a hung display.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Tested-By: Lyude Paul <lyude@redhat.com>
|
|
I already pulled the first fix, pull the GVT fixes.
- GVT fix for KBL vGPU hang to update virtual register from LRI.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180713070922.GA19840@intel.com
|
|
Two armada fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180713075427.GA16160@rmk-PC.armlinux.org.uk
|
|
Fixes for v4.18-rc5:
- Single fix for a build error when the driver is builtin,
but the backend is a loadable module.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/9c596cf5-3f24-070e-74f2-c59bfbaf68fa@linux.intel.com
|
|
drm/tegra: Fixes for v4.18-rc5
This contains a couple of one- or two-line fixes for various minor
issues in the Tegra driver.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712070142.15571-1-thierry.reding@gmail.com
|
|
A few display and GPUVM fixes for 4.18.
A few more fixes for 4.18. Two display fixes and a fix to avoid a segfault if
the GPU does not power up properly on resume. These are on top of my pull
from earlier this week.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180712043820.2877-1-alexander.deucher@amd.com
|
|
- Fix hotplug irq ack on i965/g4x (Ville)
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180710213249.GA16479@intel.com
|
|
Pull RTC fixes from Alexandre Belloni:
"Two fixes for 4.18:
- an important core fix for RTCs using the core offsetting only one
driver is affected
- a fix for the error path of mrst"
* tag 'rtc-4.18-2' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
rtc: fix alarm read and set offset
rtc: mrst: fix error code in probe()
|
|
platform_get_resource() may fail and return NULL, so we should
better check it's return value to avoid a NULL pointer dereference
a bit later in the code.
This is detected by Coccinelle semantic patch.
@@
expression pdev, res, n, t, e, e1, e2;
@@
res = platform_get_resource(pdev, t, n);
+ if (!res)
+ return -EINVAL;
... when != res == NULL
e = devm_ioremap_nocache(e1, res->start, e2);
Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The > comparisons should be >= or else we read beyond the end of the
pinctrl->functions[] array.
Fixes: cc4fa83f66e9 ("pinctrl: nsp: add pinmux driver support for Broadcom NSP SoC")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The datasheet does not document any registers to control drive strength,
and no drive strength registers are for this reason described for this
SoC. The flags indicating that drive strength can be controlled are
however set for some pins in the driver.
This leads to a NULL pointer dereference when the sh-pfc core tries to
access the struct describing the drive strength registers, for example
when reading the sysfs file pinconf-pins.
Fix this by removing the SH_PFC_PIN_CFG_DRIVE_STRENGTH from all pins.
Fixes: b92ac66a1819602b ("pinctrl: sh-pfc: Add R8A77970 PFC support")
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The .gpio_set_direction() callback was setting inverted direction
for SoCs older than the JZ4770, this restores the correct behaviour.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When we are explicitly using GPIO hogging mechanism in the pinctrl node,
such as:
&pio {
line_input {
gpio-hog;
gpios = <95 0>, <96 0>, <97 0>;
input;
};
};
A kernel panic happens at dereferencing a NULL pointer: In this case, the
drvdata is still not setup properly yet when it is being accessed.
A better solution for fixing up this issue should be we should obtain the
private data from struct gpio_chip using a specific gpiochip_get_data
instead of a generic dev_get_drvdata.
[ 0.249424] Unable to handle kernel NULL pointer dereference at virtual
address 000000c8
[ 0.257818] Mem abort info:
[ 0.260704] ESR = 0x96000005
[ 0.263869] Exception class = DABT (current EL), IL = 32 bits
[ 0.270011] SET = 0, FnV = 0
[ 0.273167] EA = 0, S1PTW = 0
[ 0.276421] Data abort info:
[ 0.279398] ISV = 0, ISS = 0x00000005
[ 0.283372] CM = 0, WnR = 0
[ 0.286440] [00000000000000c8] user address but active_mm is swapper
[ 0.293027] Internal error: Oops: 96000005 [#1] PREEMPT SMP
[ 0.298795] Modules linked in:
[ 0.301958] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 4.16.0-rc1+ #389
[ 0.308716] Hardware name: MediaTek MT7622 RFB1 board (DT)
[ 0.314396] pstate: 80000005 (Nzcv daif -PAN -UAO)
[ 0.319362] pc : mtk_hw_pin_field_get+0x28/0x118
[ 0.324140] lr : mtk_hw_set_value+0x30/0x104
[ 0.328557] sp : ffffff800801b6d0
[ 0.331983] x29: ffffff800801b6d0 x28: ffffff80086b7970
[ 0.337484] x27: 0000000000000000 x26: ffffff80087b8000
[ 0.342986] x25: 0000000000000000 x24: ffffffc00324c230
[ 0.348487] x23: 0000000000000003 x22: 0000000000000000
[ 0.353988] x21: ffffff80087b8000 x20: 0000000000000000
[ 0.359489] x19: 0000000000000054 x18: 00000000fffff7c0
[ 0.364990] x17: 0000000000006300 x16: 000000000000003f
[ 0.370492] x15: 000000000000000e x14: ffffffffffffffff
[ 0.375993] x13: 0000000000000000 x12: 0000000000000020
[ 0.381494] x11: 0000000000000006 x10: 0101010101010101
[ 0.386995] x9 : fffffffffffffffa x8 : 0000000000000007
[ 0.392496] x7 : ffffff80085d63f8 x6 : 0000000000000003
[ 0.397997] x5 : 0000000000000054 x4 : ffffffc0031eb800
[ 0.403499] x3 : ffffff800801b728 x2 : 0000000000000003
[ 0.409000] x1 : 0000000000000054 x0 : 0000000000000000
[ 0.414502] Process swapper/0 (pid: 1, stack limit = 0x000000002a913c1c)
[ 0.421441] Call trace:
[ 0.423968] mtk_hw_pin_field_get+0x28/0x118
[ 0.428387] mtk_hw_set_value+0x30/0x104
[ 0.432445] mtk_gpio_set+0x20/0x28
[ 0.436052] mtk_gpio_direction_output+0x18/0x30
[ 0.440833] gpiod_direction_output_raw_commit+0x7c/0xa0
[ 0.446333] gpiod_direction_output+0x104/0x114
[ 0.451022] gpiod_configure_flags+0xbc/0xfc
[ 0.455441] gpiod_hog+0x8c/0x140
[ 0.458869] of_gpiochip_add+0x27c/0x2d4
[ 0.462928] gpiochip_add_data_with_key+0x338/0x5f0
[ 0.467976] mtk_pinctrl_probe+0x388/0x400
[ 0.472217] platform_drv_probe+0x58/0xa4
[ 0.476365] driver_probe_device+0x204/0x44c
[ 0.480783] __device_attach_driver+0xac/0x108
[ 0.485384] bus_for_each_drv+0x7c/0xac
[ 0.489352] __device_attach+0xa0/0x144
[ 0.493320] device_initial_probe+0x10/0x18
[ 0.497647] bus_probe_device+0x2c/0x8c
[ 0.501616] device_add+0x2f8/0x540
[ 0.505226] of_device_add+0x3c/0x44
[ 0.508925] of_platform_device_create_pdata+0x80/0xb8
[ 0.514245] of_platform_bus_create+0x290/0x3e8
[ 0.518933] of_platform_populate+0x78/0x100
[ 0.523352] of_platform_default_populate+0x24/0x2c
[ 0.528403] of_platform_default_populate_init+0x94/0xa4
[ 0.533903] do_one_initcall+0x98/0x130
[ 0.537874] kernel_init_freeable+0x13c/0x1d4
[ 0.542385] kernel_init+0x10/0xf8
[ 0.545903] ret_from_fork+0x10/0x18
[ 0.549603] Code: 900020a1 f9400800 911dcc21 1400001f (f9406401)
[ 0.555916] ---[ end trace de8c34787fdad3b3 ]---
[ 0.560722] Kernel panic - not syncing: Attempted to kill init!
exitcode=0x0000000b
[ 0.560722]
[ 0.570188] SMP: stopping secondary CPUs
[ 0.574253] ---[ end Kernel panic - not syncing: Attempted to kill
init! exitcode=0x0000000b
[ 0.574253]
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If the pinctrl node has the gpio-ranges property, the range will be added
by the gpio core and doesn't need to be added by the pinctrl driver.
But for keeping backward compatibility, an explicit pinctrl_add_gpio_range
is still needed to be called when there is a missing gpio-ranges in pinctrl
node in old dts files.
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
To allow claiming hogs by pinctrl, we cannot enable pinctrl until all
groups and functions are being added done. Also, it's necessary that
the corresponding gpiochip is being added when the pinctrl device is
enabled.
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Because gpichip applied in the driver must depend on mtk eint to implement
the input data debouncing and the translation between gpio and irq, it's
better to keep logic consistent with mtk eint being built prior to gpiochip
being added.
Cc: stable@vger.kernel.org
Fixes: e6dabd38d8e7 ("pinctrl: mediatek: add EINT support to MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
It should be to return an error code when failing at groups building.
Cc: stable@vger.kernel.org
Fixes: d6ed93551320 ("pinctrl: mediatek: add pinctrl driver for MT7622 SoC")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We accidentally left out the error handling for kstrtoul().
Fixes: a520030e326a ("qlcnic: Implement flash sysfs callback for 83xx adapter")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull i2c fixes from Wolfram Sang:
- I2C core bugfix regarding bus recovery
- driver bugfix for the tegra driver
- typo correction
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: recovery: if possible send STOP with recovery pulses
i2c: tegra: Fix NACK error handling
i2c: stu300: use non-archaic spelling of failes
|
|
Pull timer fixes from Ingo Molnar:
"A clocksource driver fix and a revert"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: arm_arch_timer: Set arch_mem_timer cpumask to cpu_possible_mask
Revert "tick: Prefer a lower rating device only if it's CPU local device"
|
|
Pull rdma fixes from Jason Gunthorpe:
"Things have been quite slow, only 6 RC patches have been sent to the
list. Regression, user visible bugs, and crashing fixes:
- cxgb4 could wrongly fail MR creation due to a typo
- various crashes if the wrong QP type is mixed in with APIs that
expect other types
- syzkaller oops
- using ERR_PTR and NULL together cases HFI1 to crash in some cases
- mlx5 memory leak in error unwind"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/mlx5: Fix memory leak in mlx5_ib_create_srq() error path
RDMA/uverbs: Don't fail in creation of multiple flows
IB/hfi1: Fix incorrect mixing of ERR_PTR and NULL return values
RDMA/uverbs: Fix slab-out-of-bounds in ib_uverbs_ex_create_flow
RDMA/uverbs: Protect from attempts to create flows on unsupported QP
iw_cxgb4: correctly enforce the max reg_mr depth
|
|
Pull libnvdimm fixes from Dave Jiang:
- ensure that a variable passed in by reference to acpi_nfit_ctl is
always set to a value. An incremental patch is provided due to notice
from testing in -next. The rest of the commits did not exhibit
issues.
- fix a return path in nsio_rw_bytes() that was not returning "bytes
remain" as expected for the function.
- address an issue where applications polling on scrub-completion for
the NVDIMM may falsely wakeup and read the wrong state value and
cause hang.
- change the test unit persistent capability attribute to fix up a
broken assumption in the unit test infrastructure wrt the
'write_cache' attribute
- ratelimit dev_info() in the dax device check_vma() function since
this is easily triggered from userspace
* tag 'libnvdimm-fixes-4.18-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
nfit: fix unchecked dereference in acpi_nfit_ctl
acpi, nfit: Fix scrub idle detection
tools/testing/nvdimm: advertise a write cache for nfit_test
acpi/nfit: fix cmd_rc for acpi_nfit_ctl to always return a value
dev-dax: check_vma: ratelimit dev_info-s
libnvdimm, pmem: Fix memcpy_mcsafe() return code handling in nsio_rw_bytes()
|
|
Rather than using the index variable stored in vram. If
the device fails to come back online after a resume cycle,
reads from vram will return all 1s which will cause a
segfault. Based on a patch from Thomas Martitz <kugel@rockbox.org>.
This avoids the segfault, but we still need to sort out
why the GPU does not come back online after a resume.
Bug: https://bugs.freedesktop.org/show_bug.cgi?id=105760
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
The offset needs to be added after reading the alarm value.
It also needs to be subtracted after the now < alarm test.
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
Alexey Kardashevskiy
David Lechner
Alexander Sverdlin
Hersen Wu
Leo Liu
Weiping Zhang
Scott Bauer
Sanjeev Bansal
Siva Reddy Kallam
John Allen
Stefan Wahren
Saeed Mahameed
Stephen Hemminger
Thomas Falcon
Corentin Labbe
Toshiaki Makita
Linus Torvalds
Frank Rowand
Lyude Paul
Dan Carpenter
Ben Skeggs
Dave Airlie
Wei Yongjun
Niklas Söderlund
Paul Cercueil
Sean Wang
Alex Deucher
Alexandre Belloni