| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Use phy_support_asym_pause() rather than open-coding it.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Kalle Valo says:
====================
wireless-drivers-next patches for v5.5
Second set of patches for v5.5. Nothing special this time, smaller
features to various drivers and of course fixes all over.
Major changes:
iwlwifi
* update scan FW API
* bump the supported FW API version
* add debug dump collection on assert in WoWLAN
* enable adaptive dwell on P2P interfaces
ath10k
* request for PM_QOS_CPU_DMA_LATENCY to improve firmware initialisation time
qtnfmac
* add support for getting/setting transmit power
* handle MIC failure event from firmware
rtl8xxxu
* add support for Edimax EW-7611ULB
wil6210
* add SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A bonding with layer2+3 or layer3+4 hashing uses the IP addresses and the ports
to balance packets between slaves. With some network errors, we receive an ICMP
error packet by the remote host or a router. If sent by a router, the source IP
can differ from the remote host one. Additionally the ICMP protocol has no port
numbers, so a layer3+4 bonding will get a different hash than the previous one.
These two conditions could let the packet go through a different interface than
the other packets of the same flow:
# tcpdump -qltnni veth0 |sed 's/^/0: /' &
# tcpdump -qltnni veth1 |sed 's/^/1: /' &
# hping3 -2 192.168.0.2 -p 9
0: IP 192.168.0.1.2251 > 192.168.0.2.9: UDP, length 0
1: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
1: IP 192.168.0.1.2252 > 192.168.0.2.9: UDP, length 0
1: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
1: IP 192.168.0.1.2253 > 192.168.0.2.9: UDP, length 0
1: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
0: IP 192.168.0.1.2254 > 192.168.0.2.9: UDP, length 0
1: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
An ICMP error packet contains the header of the packet which caused the network
error, so inspect it and match the flow against it, so we can send the ICMP via
the same interface of the previous packet in the flow.
Move the IP and port dissect code into a generic function bond_flow_ip() and if
we are dissecting an ICMP error packet, call it again with the adjusted offset.
# hping3 -2 192.168.0.2 -p 9
1: IP 192.168.0.1.1224 > 192.168.0.2.9: UDP, length 0
1: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
1: IP 192.168.0.1.1225 > 192.168.0.2.9: UDP, length 0
1: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
0: IP 192.168.0.1.1226 > 192.168.0.2.9: UDP, length 0
0: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
0: IP 192.168.0.1.1227 > 192.168.0.2.9: UDP, length 0
0: IP 192.168.0.2 > 192.168.0.1: ICMP 192.168.0.2 udp port 9 unreachable, length 36
Signed-off-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit 0c65b2b90d13c ("net: of_get_phy_mode: Change API to solve
int/unit warnings") updated the function of_get_phy_mode declaration.
Now it returns an error code and in case the node doesn't contain the
property 'phy-mode' or 'phy-connection-type' it returns -EINVAL and would
set the phy_interface_t to PHY_INTERFACE_MODE_NA.
Ocelot VSC7514 has 4 internal phys which have the phy interface
PHY_INTERFACE_MODE_NA. So because of_get_phy_mode would assign
PHY_INTERFACE_MODE_NA to phy_mode when there is an error, there is no need
to add the error check.
Updates for v2:
- drop error check because of_get_phy_mode already assigns phy_interface
to PHY_INTERFACE_MODE in case of error.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All .rw_reset callbacks except bnx2x_84833_hw_reset_phy() use a
void return type. No callers of .hw_reset check a return value and
bnx2x_84833_hw_reset_phy() unconditionally returns 0. Remove all
hw_reset_t casts and fix the return type to void.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The return values for format_fw_ver_t callbacks are supposed to be
"int", not "u8". Ultimately, the top-level caller doesn't actually check
the return value at all, but just clean this all up anyway and fix the
prototypes so that casts are no longer needed.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No callers of .config_init check return values. Remove the casting and
change all callbacks to have the correct function prototype.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function casts for .read_status callbacks end up casting some int
return values to u8. This seems to be bug-prone (-EINVAL being returned
into something that appears to be true/false), but fixing the function
prototypes doesn't change the existing behavior. Fix the return values
to remove the casts.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NULL is already "void *" so it will auto-cast in assignments and
initializers. Additionally, all the callbacks for .link_reset,
.config_loopback, .set_link_led, and .phy_specific_func are already
correct. No casting is needed for these, so remove them.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ENETC has a register PSPEED to indicate the link speed of hardware.
It is need to update accordingly. PSPEED field needs to be updated
with the port speed for QBV scheduling purposes. Or else there is
chance for gate slot not free by frame taking the MAC if PSPEED and
phy speed not match. So update PSPEED when link adjust. This is
implement by the adjust_link.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ENETC supports in hardware for time-based egress shaping according
to IEEE 802.1Qbv. This patch implement the Qbv enablement by the
hardware offload method qdisc tc-taprio method.
Also update cbdr writeback to up level since control bd ring may
writeback data to control bd ring.
Signed-off-by: Po Liu <Po.Liu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The page pool keeps track of the number of pages in flight, and
it isn't safe to remove the pool until all pages are returned.
Disallow removing the pool until all pages are back, so the pool
is always available for page producers.
Make the page pool responsible for its own delayed destruction
instead of relying on XDP, so the page pool can be used without
the xdp memory model.
When all pages are returned, free the pool and notify xdp if the
pool is registered with the xdp memory system. Have the callback
perform a table walk since some drivers (cpsw) may share the pool
among multiple xdp_rxq_info.
Note that the increment of pages_state_release_cnt may result in
inflight == 0, resulting in the pool being released.
Fixes: d956a048cd3f ("xdp: force mem allocator removal and periodic warning")
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a race in the TUN driver between napi_busy_loop and
napi_gro_frags. This commit resolves the race by adding the NAPI struct
via netif_tx_napi_add, instead of netif_napi_add, which disables polling
for the NAPI struct.
KCSAN reported:
BUG: KCSAN: data-race in gro_normal_list.part.0 / napi_busy_loop
write to 0xffff8880b5d474b0 of 4 bytes by task 11205 on cpu 0:
gro_normal_list.part.0+0x77/0xb0 net/core/dev.c:5682
gro_normal_list net/core/dev.c:5678 [inline]
gro_normal_one net/core/dev.c:5692 [inline]
napi_frags_finish net/core/dev.c:5705 [inline]
napi_gro_frags+0x625/0x770 net/core/dev.c:5778
tun_get_user+0x2150/0x26a0 drivers/net/tun.c:1976
tun_chr_write_iter+0x79/0xd0 drivers/net/tun.c:2022
call_write_iter include/linux/fs.h:1895 [inline]
do_iter_readv_writev+0x487/0x5b0 fs/read_write.c:693
do_iter_write fs/read_write.c:970 [inline]
do_iter_write+0x13b/0x3c0 fs/read_write.c:951
vfs_writev+0x118/0x1c0 fs/read_write.c:1015
do_writev+0xe3/0x250 fs/read_write.c:1058
__do_sys_writev fs/read_write.c:1131 [inline]
__se_sys_writev fs/read_write.c:1128 [inline]
__x64_sys_writev+0x4e/0x60 fs/read_write.c:1128
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
read to 0xffff8880b5d474b0 of 4 bytes by task 11168 on cpu 1:
gro_normal_list net/core/dev.c:5678 [inline]
napi_busy_loop+0xda/0x4f0 net/core/dev.c:6126
sk_busy_loop include/net/busy_poll.h:108 [inline]
__skb_recv_udp+0x4ad/0x560 net/ipv4/udp.c:1689
udpv6_recvmsg+0x29e/0xe90 net/ipv6/udp.c:288
inet6_recvmsg+0xbb/0x240 net/ipv6/af_inet6.c:592
sock_recvmsg_nosec net/socket.c:871 [inline]
sock_recvmsg net/socket.c:889 [inline]
sock_recvmsg+0x92/0xb0 net/socket.c:885
sock_read_iter+0x15f/0x1e0 net/socket.c:967
call_read_iter include/linux/fs.h:1889 [inline]
new_sync_read+0x389/0x4f0 fs/read_write.c:414
__vfs_read+0xb1/0xc0 fs/read_write.c:427
vfs_read fs/read_write.c:461 [inline]
vfs_read+0x143/0x2c0 fs/read_write.c:446
ksys_read+0xd5/0x1b0 fs/read_write.c:587
__do_sys_read fs/read_write.c:597 [inline]
__se_sys_read fs/read_write.c:595 [inline]
__x64_sys_read+0x4c/0x60 fs/read_write.c:595
do_syscall_64+0xcc/0x370 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Reported by Kernel Concurrency Sanitizer on:
CPU: 1 PID: 11168 Comm: syz-executor.0 Not tainted 5.4.0-rc6+ #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Fixes: 943170998b20 ("tun: enable NAPI for TUN/TAP driver")
Signed-off-by: Petar Penkov <ppenkov@google.com>
Reported-by: syzbot <syzkaller@googlegroups.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This supports an Ethernet switching core from Vitesse / Microsemi /
Microchip (VSC9959) which is part of the Ocelot family (a brand name),
and whose code name is Felix. The switch can be (and is) integrated on
different SoCs as a PCIe endpoint device.
The functionality is provided by the core of the Ocelot switch driver
(drivers/net/ethernet/mscc). In this regard, the current driver is an
instance of Microsemi's Ocelot core driver, with a DSA front-end. It
inherits its name from VSC9959's code name, to distinguish itself from
the switchdev ocelot driver.
The patch adds the logic for probing a PCI device and defines the
register map for the VSC9959 switch core, since it has some differences
in register addresses and bitfield mappings compared to the other Ocelot
switches (VSC7511, VSC7512, VSC7513, VSC7514).
The Felix driver declares the register map as part of the "instance
table". Currently the VSC9959 inside NXP LS1028A is the only instance,
but presumably it can support other switches in the Ocelot family, when
used in DSA mode (Linux running on the external CPU, and not on the
embedded MIPS).
In a few cases, some h/w operations have to be done differently on
VSC9959 due to missing bitfields. This is the case for the switch core
reset and init. Because for this operation Ocelot uses some bits that
are not present on Felix, the latter has to use a register from the
global registers block (GCB) instead.
Although it is a PCI driver, it relies on DT bindings for compatibility
with DSA (CPU port link, PHY library). It does not have any custom
device tree bindings, since we would like to minimize its dependency on
device tree though.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Felix DSA driver needs to write to SYS_RAM_INIT_RAM_INIT for its own
chip initialization process.
Also update the MAINTAINERS file such that the headers exported by the
ocelot driver are under the same maintainers' umbrella as the driver
itself.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We will be registering another switch driver based on ocelot, which
lives under drivers/net/dsa.
Make sure the Felix DSA front-end has the necessary abstractions to
implement a new Ocelot driver instantiation. This includes the function
prototypes for implementing DSA callbacks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Felix switch has a different reset procedure, so a function pointer
needs to be created and added to the ocelot_ops structure.
The reset procedure has been moved into ocelot_init.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the NPI port, the DSA tag is passed through Ethernet, so the
switch's MAC needs to accept it as it comes from the DSA master. Increase
the MTU on the external CPU port to account for the length of the
injection header.
Without this patch, MTU-sized frames are dropped by the switch's CPU
port on xmit, which is especially obvious in TCP sessions.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This constant will be used in a future patch to increase the MTU on NPI
ports, and will also be used in the tagger driver for Felix.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since in an NPI/DSA setup, not all ports will have the same MTU, we need
to make sure the watermarks for pause frames and/or tail dropping logic
that existed in the driver is still coherent for the new MTU values.
We need to do this because the NPI (aka external CPU) port needs an
increased MTU for the DSA tag. This will be done in a future patch.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It doesn't make sense to rewrite all these registers every time the PHY
library notifies us about a link state change.
In a future patch we will customize the MTU for the CPU port, and since
the MTU was previously configured from adjust_link, if we don't make
this change, its value would have got overridden.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The adjust_link routine should be generic enough to be (re)used by
any SoC that integrates a switch core compatible with the Ocelot
core switch driver. Currently all configurations are generic except
for the PCS settings that are SoC specific. Move these out to the
Ocelot SoC/board instance.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Let's make this ioremap and regmap init code common. It should not
be platform dependent as it should be usable by PCI devices too.
Use better names where necessary to avoid clashes.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SMCD link group termination is called when peer signals its shutdown
of its corresponding link group. For regular shutdowns no connections
exist anymore. For abnormal shutdowns connections must be killed and
their DMBs must be unregistered immediately. That means the SMCR method
to delay the link group freeing several seconds does not fit.
This patch adds immediate termination of a link group and its SMCD
connections and makes sure all SMCD link group related cleanup steps
are finished.
Signed-off-by: Ursula Braun <ubraun@linux.ibm.com>
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that TX Coalesce has been rewritten we no longer need this
additional interrupt enabled. This reduces CPU usage.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Coalesce logic currently increments the number of packets and sets the
IC bit when the coalesced packets have passed a given limit. This does
not reflect very well what coalesce was meant for as we can have a large
number of packets that are coalesced and then a single one, sent later
on that has the IC bit.
Rework the logic so that it coalesces only upon a limit of packets and
sets the IC bit for large number of packets.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tune-up the defalt coalesce settings for optimal values. This gives the
best performance in most of the use-cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RFA and RFD should not be dependent on FIFO size. In fact, the more FIFO
space we have, the later we can activate Flow Control. Let's use
hard-coded values for RFA and RFD for all FIFO sizes with the exception
of 4k, which is a special case.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For performance reasons, sometimes using the minimum RX Coalesce value
is not optimal. Lets setup a default value that is optimal in most of
the use cases.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We may only want to use the RX Watchdog so lets check if RX Coalesce
settings are non-zero and only set the RX Interrupt on Completion bit if
its not.
Signed-off-by: Jose Abreu <Jose.Abreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 0c3cbbf96def ("mlxsw: Add specific trap for packets routed via
invalid nexthops") allocated an adjacency entry during driver
initialization whose purpose is to discard packets hitting the route
pointing to it.
These adjacency entries are allocated from a resource called KVD linear
(KVDL). There are situations in which the user can decide to set the
size of this resource (via devlink-resource) to 0, in which case the
driver will not be able to load.
Therefore, instead of pre-allocating this adjacency entry, simply
allocate it only when needed. A variable indicating the validity of the
entry is added and is used to ensure it is only allocated and written
once and that it is freed after all the routes were flushed.
Fixes: 0c3cbbf96def ("mlxsw: Add specific trap for packets routed via invalid nexthops")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove duplicated include.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c: In function rtl8xxxu_gen2_config_channel:
drivers/net/wireless/realtek/rtl8xxxu/rtl8xxxu_core.c:1266:13: warning: variable rsr set but not used [-Wunused-but-set-variable]
rsr is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Chris Chiu <chiu@endlessm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Signed-off-by: Eduardo Abinader <eduardoabinader@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
ath.git patches for v5.5. Major changes:
ath10k
* request for PM_QOS_CPU_DMA_LATENCY to improve firmware initialisation time
|
|
The code now compiles without ACPI, but there's a warning since
iwl_mvm_get_ppag_table() isn't used, and iwl_mvm_ppag_init() must
not unconditionally fail but return success instead.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Somehow two tabs snuck into this file where just one should be
used, fix that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The firmware API has changed a little bit but this change
has no impact on the flow and is backward compatible.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The current budget of 2000mA is preventing us from reaching maximum
throughput. According to our system engineers, we can increase the
maximum budget to 2400mA to solve this problem.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
There are various of flows which require tids flushing
(disconnection, suspend, etc...).
Currently, when the driver instructs the FW to flush
he masks all the data tids(0-7).
However, the driver doesn't set the management tid (#15)
which cause the FW not to flush it.
When the FW tries to remove the mgmt queue he throws an assert
since it is not an empty queue.
instead of just set only the data tids set everything and let
the FW ignore the invalid tids.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Align to the requirement update and support adaptive dwell in p2p scan.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Refactored the SAR related functions from iwlmvm to acpi
in order to make it shared between different opmodes
in addition to removing unused variable ppag_rev.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement scan request command version 12.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Implement a new versioning handling flow supported from version 11
onwards.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is present since the introduction of iwlmvm.
Example stack trace on MIPS:
[<ffffffffc0789328>] iwl_mvm_rx_rx_mpdu+0xa8/0xb88 [iwlmvm]
[<ffffffffc0632b40>] iwl_pcie_rx_handle+0x420/0xc48 [iwlwifi]
Tested with a Wireless AC 7265 for ~6 months, confirmed to fix the
problem. No other unaligned accesses are spotted yet.
Signed-off-by: Wang Xuerui <wangxuerui@qiniu.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The variable bufsz is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Start supporting API version 51 for 22000 series.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Add a reference to the correct enum rather than showing
the pattern of the actual constants.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
Russell King
David S. Miller
Matteo Croce
Horatiu Vultur
Kees Cook
Po Liu
Jonathan Lemon
Petar Penkov
Vladimir Oltean
Claudiu Manoil
Ursula Braun
Jose Abreu
Ido Schimmel
YueHaibing
Zheng Yongjun
Eduardo Abinader
Kalle Valo
Johannes Berg
Emmanuel Grumbach
Mordechay Goodstein
Haim Dreyfuss
Shahar S Matityahu
Ihab Zhaika
Wang Xuerui
Colin Ian King
Luca Coelho