| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
o Remove extra printing of mac address
o This driver also supports NIC only Qlogic adapters.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During device soft reset, don't halt every device block.
Access to some blocks is required during recovery.
Signed-off-by: Sucheta Chakraborty <sucheta@dut4145.unminc.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ipv6 support to the be2net driver.
Signed-off-by: Ajit Khaparde <ajitk@serverengines.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changed the driver version number to 5.0.4
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver was not detecting the presence of NIC partitioning capability of the
firmware properly. Now, it checks the eswitch set bit in the FW capabilities
register and accordingly sets the driver mode as NPAR capable or not.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Based upon a report by Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SKBs hold onto resources that can't be held indefinitely, such as TCP
socket references and netfilter conntrack state. So if a packet is left
in TX ring for a long time, there might be a TCP socket that cannot be
closed and freed up.
Current blackfin EMAC driver always reclaim and free used tx skbs in future
transfers. The problem is that future transfer may not come as soon as
possible. This patch start a timer after transfer to reclaim and free skb.
There is nearly no performance drop with this patch.
TX interrupt is not enabled because of a strange behavior of the Blackfin EMAC.
If EMAC TX transfer control is turned on, endless TX interrupts are triggered
no matter if TX DMA is enabled or not. Since DMA walks down the ring automatically,
TX transfer control can't be turned off in the middle. The only way is to disable
TX interrupt completely.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the code that handles the error case when cnic_cm_abort() cannot
proceed normally. We cannot just set the csk->state and we must
go through cnic_ready_to_close() to handle all the conditions. We
also add error return code in cnic_cm_abort().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Combine RESET_RECEIVED and RESET_COMP logic and fix race condition
between these 2 events and cnic_cm_close(). In particular, we need
to (test_and_clear_bit(SK_F_OFFLD_COMPLETE, &csk->flags)) before we
update csk->state.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move chip-specific code to the respective chip's ->close_conn() functions
for better code organization.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
So that bnx2i can handle the error condition immediately and not have to
wait for timeout.
Signed-off-by: Michael Chan <mchan@broadcom.com.
Signed-off-by: Eddie Wai <waie@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change corrects issues where macvlan was not correctly triggering
promiscuous mode on ixgbe due to the filters not being correctly set. It
also corrects the fact that VF rar filters were being overwritten when the
PF was reset.
CC: Shirley Ma <xma@us.ibm.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register net_bridge_port pointer as rx_handler data pointer. As br_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a bridge port. Also rcuized pointers are now correctly
dereferenced in br_fdb.c and in netfilter parts.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register macvlan_port pointer as rx_handler data pointer. As macvlan_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a macvlan port.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add possibility to register rx_handler data pointer along with a rx_handler.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change 2wire transfer rate of SFP+ module EEPROM from 400Khz to 100Khz
since some DACs(direct attached cables) do not work at 400Khz.
Reported-by: Krzysztof Oldzki <ole@ans.pl>
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Uses a seqcount_t to synchronize stat producer and consumer, for packets
and bytes counter, now u64 types.
(dropped counter being rarely used, stay a native "unsigned long" type)
No noticeable performance impact on x86, as it only adds two increments
per frame. It might be more expensive on arches where smp_wmb() is not
free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ixgbe/ixgbe_ethtool.c
With merge conflict help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch added to 2.6.34:
commit f8d1dcaf88bddc7f282722ec1fdddbcb06a72f18
Author: Jesse Brandeburg <jesse.brandeburg@intel.com>
Date: Tue Apr 27 01:37:20 2010 +0000
ixgbe: enable extremely low latency
introduced a feature where LRO (called RSC on the hardware) was disabled
automatically when setting rx-usecs to 0 via ethtool. Some might not
like the fact that LRO was disabled automatically, but I'm fine with
that. What I don't like is that LRO/RSC is automatically enabled when
rx-usecs is set >0 via ethtool.
This would certainly be a problem if the device was used for forwarding
and it was determined that the low latency wasn't needed after the
device was already forwarding. I played around with saving the state of
LRO in the driver, but it just didn't seem worthwhile and would require
a small change to dev_disable_lro() that I did not like.
This patch simply leaves LRO disabled when setting rx-usecs >0 and
requires that the user enable it again. An extra informational message
will also now appear in the log so users can understand why LRO isn't
being enabled as they expect.
Inconsistency of LRO setting first noticed by Stanislaw Gruszka.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
CC: Stanislaw Gruszka <sgruszka@redhat.com>
CC: stable@kernel.org
Tested-by: Stephen Ko <stephen.s.ko@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 675ad47375c76a7c3be4ace9554d92cd55518ced
removed the capability to use ethtool.set_msglevel to
control the types of messages emitted by the driver.
That commit should probably be reverted.
If not, then this patch fixes a message logging defect
introduced by converting a printk without KERN_<level>
to e_info.
This also reduces text by about 200 bytes.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a small window where the watchdog could be running as the
interface is brought down on a NIC with two ports wired back to back.
If ixgbe_update_status is then called can lead to a panic. This patch
allows the update to bail if we are in that condition.
This issue was orignally reported and fix proposed by Akihiko Saitou.
CC: Akihiko Saitou <asaitou@users.sourceforge.net>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use struct rtnl_link_stats64 as the statistics structure.
On 32-bit architectures, insert 32 bits of padding after/before each
field of struct net_device_stats to make its layout compatible with
struct rtnl_link_stats64. Add an anonymous union in net_device; move
stats into the union and add struct rtnl_link_stats64 stats64.
Add net_device_ops::ndo_get_stats64, implementations of which will
return a pointer to struct rtnl_link_stats64. Drivers that implement
this operation must not update the structure asynchronously.
Change dev_get_stats() to call ndo_get_stats64 if available, and to
return a pointer to struct rtnl_link_stats64. Change callers of
dev_get_stats() accordingly.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ioctl operation (ndo_do_ioctl) is added to make mii-tools work
Signed-off-by: Sergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix build warning on i386 (32-bit) with 32-bit dma_addr_t:
drivers/net/enic/vnic_dev.c: In function 'vnic_dev_init_prov':
drivers/net/enic/vnic_dev.c:716: warning: passing argument 3 of 'pci_alloc_consistent' from incompatible pointer type
include/asm-generic/pci-dma-compat.h:16: note: expected 'dma_addr_t *' but argument is of type 'u64 *'
Now builds without warnings on i386 and on x86_64.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Scott Feldman <scofeldm@cisco.com>
Cc: Vasanthy Kolluri <vkolluri@cisco.com>
Cc: Roopa Prabhu <roprabhu@cisco.com>
Acked-by: Scott Feldman <scofeldm@cisco.com>
|
|
drivers/net/bnx2.c: In function 'bnx2_disable_forced_2g5':
drivers/net/bnx2.c:1489: warning: 'bmcr' may be used uninitialized in this function
We fix it by checking return values from all bnx2_read_phy() and proceeding
to do read-modify-write only if the read operation is successful.
The related bnx2_enable_forced_2g5() is also fixed the same way.
Reported-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If oui were a null variable then vic_provinfo_alloc() would leak memory.
But this function is only called from one place and oui is not null so
I removed the check.
I also moved the memory allocation down a line so it was easier to spot.
(No one ever reads variable declarations).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
The point of using the devres resource management routines is that they
simplify the driver by taking care of releasing resources on failure and
release. A recent commit added a bunch of error handling that is unnecessary
in this context.
This patch removes this redundant error handling, as well as using
dmam_alloc_coherent in place of dma_alloc_coherent in order to use this
framework consistenly throughout the driver.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This matches what ethoc_mdio_read does and makes the functions
symmetric.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
- No need to iterate over all possible addresses on bus
- Use helper function phy_find_first
- Use phy_connect_direct as we already have the relevant structure
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves the write of the TX_BD_NUM to init_ring together with the
rest of the code setting up the transmission buffers.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethoc driver should be writing bus addresses to the ethoc registers, not
virtual addresses. This patch adds an array to store the virtual addresses
in and references that array when manipulating the contents of the buffer
descriptors.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves the calculation of the number of transmission buffers to
ethoc_probe where it more logically fits with the rest of the memory
allocation code.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
i2400m_fw_hdr_check() was accessing hardware field
bcf_hdr->module_type (little endian 32) without converting to host
byte sex.
Reported-by: Данилин Михаил <mdanilin@nsg.net.ru>
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
|
|
Conflicts:
drivers/net/wireless/wl12xx/wl1271.h
drivers/net/wireless/wl12xx/wl1271_cmd.h
|
|
remove useless union keyword in rtable, rt6_info and dn_route.
Since there is only one member in a union, the union keyword isn't useful.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
fix a race at the end of NAPI complete processing, it had
better do __napi_complete() first before re-enable interrupt.
Signed-off-by:Figo.zhang <figo1802@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need for pppoe_xmit() forward declaration in
drivers/net/pppoe.c. This patch removes this pppoe_xmit() declaration.
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Realtek confirmed that a 20us delay is needed after mdio_read and
mdio_write operations. Reduce the delay in mdio_write, and add it
to mdio_read too. Also add a comment that the 20us is from hw specs.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit cc772ab7cdcaa24d1fae332d92a1602788644f7a ("gianfar: Add
hardware RX timestamping support"), the driver no longer works on
at least MPC8313ERDB and MPC8568EMDS boards (and possibly much more
boards as well).
That's how MPC8313 Reference Manual describes RCTRL_TS_ENABLE bit:
Timestamp incoming packets as padding bytes. PAL field is set
to 8 if the PAL field is programmed to less than 8. Must be set
to zero if TMR_CTRL[TE]=0.
I see that the commit above sets this bit, but it doesn't handle
TMR_CTRL. Manfred probably had this bit set by the firmware for
his boards. But obviously this isn't true for all boards in the
wild.
Also, I recall that Freescale BSPs were explicitly disabling the
timestamping because of a performance drop.
For now, the best way to deal with this is just disable the
timestamping, and later we can discuss proper device tree bindings
and implement enabling this feature via some property.
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements a work around for Erratum 5, "3.3 V Fiber Speed
Selection." If the hardware wiring does not respect this erratum, then
fiber optic mode will not work properly.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Using ieee80211_find_sta() needs to be under
RCU read lock, which iwlwifi currently misses,
so fix it.
Cc: stable@kernel.org
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Tested-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Reading the ELP_CTRL register with sdio_readb causes problems because
hardware seems to be performing a write using stuff bits in the request
(those bits contain write data in write request). This indicates that it
actually expects RAW (read after write) type of request, so perform that
when reading ELP_CTRL instead. Also cache last written value so we know
what to write when doing RAW request.
Because of the above it was not possible to wake the chip from ELP power
saving mode, PM had to be disabled to have the driver usable in SDIO
mode. After this patch PM is functional.
For backporting to 2.6.34 or earlier, this patch depends on
6c1f716e8154ee9315534782b9b1eedea0559a24, which adds the
required SDIO funcion.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Since ath5k_hw_set_antenna_mode() always writes the default antenna register
and is called at the end of reset, there is no need to separately save and
restore the default antenna.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
Sritej Velaga
Sucheta Chakraborty
Ajit Khaparde
Anirban Chakraborty
David S. Miller
Sonic Zhang
Michael Chan
Alexander Duyck
Jiri Pirko
Yaniv Rosner
Eric Dumazet
Andy Gospodarek
Joe Perches
Don Skidmore
Ben Hutchings
Sergey Matyukevich
Randy Dunlap
Dan Carpenter
Jonas Bonn
Inaky Perez-Gonzalez
Changli Gao
Figo.zhang
Rami Rosen
Timo Teräs
Anton Vorontsov
Richard Cochran
Johannes Berg
Grazvydas Ignotas
Bruno Randolf