aboutsummaryrefslogtreecommitdiffstats
path: root/drivers (follow)
AgeCommit message (Collapse)AuthorFilesLines
2018-07-04igb: Refactor igb_offload_cbs()Jesus Sanchez-Palencia1-9/+14
Split code into a separate function (igb_offload_apply()) that will be used by ETF offload implementation. Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04igb: Only change Tx arbitration when CBS is onJesus Sanchez-Palencia1-16/+33
Currently the data transmission arbitration algorithm - DataTranARB field on TQAVCTRL reg - is always set to CBS when the Tx mode is changed from legacy to 'Qav' mode. Make that configuration a bit more granular in preparation for the upcoming Launchtime enabling patches, since CBS and Launchtime can be enabled separately. That is achieved by moving the DataTranARB setup to igb_config_tx_modes() instead. Similarly, when disabling CBS we must check if it has been disabled for all queues, and clear the DataTranARB accordingly. Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04igb: Refactor igb_configure_cbs()Jesus Sanchez-Palencia1-32/+28
Make this function retrieve what it needs from the Tx ring being addressed since it already relies on what had been saved on it before. Also, since this function will be used by the upcoming Launchtime patches rename it to better reflect its intention. Note that Launchtime is not part of what 802.1Qav specifies, but the i210 datasheet refers to this set of functionality as "Qav Transmission Mode". Here we also perform a tiny refactor at is_any_cbs_enabled(), and add further documentation to igb_setup_tx_mode(). Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04isdn: mark expected switch fall-throughsGustavo A. R. Silva15-0/+33
In preparation to enabling -Wimplicit-fallthrough, mark switch cases where we are expecting to fall through. Warning level 2 was used: -Wimplicit-fallthrough=2 Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04net: usb: asix: allow optionally getting mac address from device treeMarcel Ziswiler1-15/+23
For Embedded use where e.g. AX88772B chips may be used without external EEPROMs the boot loader may choose to pass the MAC address to be used via device tree. Therefore, allow for optionally getting the MAC address from device tree data e.g. as follows (excerpt from a T30 based board, local-mac-address to be filled in by boot loader): /* EHCI instance 1: USB2_DP/N -> AX88772B */ usb@7d004000 { status = "okay"; #address-cells = <1>; #size-cells = <0>; asix@1 { reg = <1>; local-mac-address = [00 00 00 00 00 00]; }; }; Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04vhost_net: Avoid rx vring kicks during busyloopToshiaki Makita1-3/+7
We may run out of avail rx ring descriptor under heavy load but busypoll did not detect it so busypoll may have exited prematurely. Avoid this by checking rx ring full during busypoll. Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04vhost_net: Avoid rx queue wake-ups during busypollToshiaki Makita1-7/+19
We may run handle_rx() while rx work is queued. For example a packet can push the rx work during the window before handle_rx calls vhost_net_disable_vq(). In that case busypoll immediately exits due to vhost_has_work() condition and enables vq again. This can lead to another unnecessary rx wake-ups, so poll rx work instead of enabling the vq. Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04vhost_net: Avoid tx vring kicks during busyloopToshiaki Makita1-13/+22
Under heavy load vhost busypoll may run without suppressing notification. For example tx zerocopy callback can push tx work while handle_tx() is running, then busyloop exits due to vhost_has_work() condition and enables notification but immediately reenters handle_tx() because the pushed work was tx. In this case handle_tx() tries to disable notification again, but when using event_idx it by design cannot. Then busyloop will run without suppressing notification. Another example is the case where handle_tx() tries to enable notification but avail idx is advanced so disables it again. This case also leads to the same situation with event_idx. The problem is that once we enter this situation busyloop does not work under heavy load for considerable amount of time, because notification is likely to happen during busyloop and handle_tx() immediately enables notification after notification happens. Specifically busyloop detects notification by vhost_has_work() and then handle_tx() calls vhost_enable_notify(). Because the detected work was the tx work, it enters handle_tx(), and enters busyloop without suppression again. This is likely to be repeated, so with event_idx we are almost not able to suppress notification in this case. To fix this, poll the work instead of enabling notification when busypoll is interrupted by something. IMHO vhost_has_work() is kind of interruption rather than a signal to completely cancel the busypoll, so let's run busypoll after the necessary work is done. Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04vhost_net: Rename local variables in vhost_net_rx_peek_head_lenToshiaki Makita1-17/+17
So we can easily see which variable is for which, tx or rx. Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by: Jason Wang <jasowang@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04sfc: batch up RX deliveryEdward Cree3-1/+21
Improves packet rate of 1-byte UDP receives by up to 10%. Signed-off-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04net: dsa: Add Vitesse VSC73xx DSA router driverLinus Walleij3-0/+1376
This adds a DSA driver for: Vitesse VSC7385 SparX-G5 5-port Integrated Gigabit Ethernet Switch Vitesse VSC7388 SparX-G8 8-port Integrated Gigabit Ethernet Switch Vitesse VSC7395 SparX-G5e 5+1-port Integrated Gigabit Ethernet Switch Vitesse VSC7398 SparX-G8e 8-port Integrated Gigabit Ethernet Switch These switches have a built-in 8051 CPU and can download and execute firmware in this CPU. They can also be configured to use an external CPU handling the switch in a memory-mapped manner by connecting to that external CPU's memory bus. This driver (currently) only takes control of the switch chip over SPI and configures it to route packages around when connected to a CPU port. The chip has embedded PHYs and VLAN support so we model it using DSA as a best fit so we can easily add VLAN support and maybe later also exploit the internal frame header to get more direct control over the switch. The four built-in GPIO lines are exposed using a standard GPIO chip. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04net: phy: vitesse: Add support for VSC73xxLinus Walleij1-0/+175
The VSC7385, VSC7388, VSC7395 and VSC7398 are integrated switch/router chips for 5+1 or 8-port switches/routers. When managed directly by Linux using DSA we need to do a special set-up "dance" on the PHY. Unfortunately these sequences switches the PHY to undocumented pages named 2a30 and 52b6 and does undocumented things. It is described by these opaque sequences also in the reference manual. This is a best effort to integrate it anyways. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller1-2/+3
Daniel Borkmann says: ==================== pull-request: bpf-next 2018-07-03 The following pull-request contains BPF updates for your *net-next* tree. The main changes are: 1) Various improvements to bpftool and libbpf, that is, bpftool build speed improvements, missing BPF program types added for detection by section name, ability to load programs from '.text' section is made to work again, and better bash completion handling, from Jakub. 2) Improvements to nfp JIT's map read handling which allows for optimizing memcpy from map to packet, from Jiong. 3) New BPF sample is added which demonstrates XDP in combination with bpf_perf_event_output() helper to sample packets on all CPUs, from Toke. 4) Add a new BPF kselftest case for tracking connect(2) BPF hooks infrastructure in combination with TFO, from Andrey. 5) Extend the XDP/BPF xdp_rxq_info sample code with a cmdline option to read payload from packet data in order to use it for benchmarking. Also for '--action XDP_TX' option implement swapping of MAC addresses to avoid drops on some hardware seen during testing, from Jesper. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: aquantia: bump driver versionIgor Russkikh1-2/+2
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: aquantia: Add renegotiate ethtool operation supportAnton Mikaev4-0/+63
Adds ethtool -r|--negotiate operation support. It triggers special control bit on FW interface causing FW to restart link negotiation. Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: Anton Mikaev <amikaev@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: aquantia: Implement rx/tx flow control ethtools callbackIgor Russkikh4-1/+74
Runtime change of pause frame configuration (rx/tx flow control) via ethtool. Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: aquantia: Improve adapter init/deinit logicIgor Russkikh6-31/+66
We now pass link drop status to FW on init/deinit. This is required to inform FW that driver took/released a control on link. FW then will manage its own state and device power profile based on this information. To improve management we remove mpi_set function which ambiguously took both state and speed parameters. Deinit callback is now a part of FW ops, as it actually manages the FW. Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: aquantia: Ethtool based ring size configurationAnton Mikaev7-50/+136
Implemented ring size setup, min/max validation and reconfiguration in runtime. Signed-off-by: Anton Mikaev <amikaev@aquantia.com> Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: stmmac_tc: use 64-bit arithmetic instead of 32-bitGustavo A. R. Silva1-3/+3
Add suffix UL to constant 1024 in order to give the compiler complete information about the proper arithmetic to use. Notice that this constant is used in a context that expects an expression of type u64 (64 bits, unsigned) and following expressions are currently being evaluated using 32-bit arithmetic: qopt->idleslope * 1024 * ptr qopt->hicredit * 1024 * 8 qopt->locredit * 1024 * 8 Addresses-Coverity-ID: 1470246 ("Unintentional integer overflow") Addresses-Coverity-ID: 1470248 ("Unintentional integer overflow") Addresses-Coverity-ID: 1470249 ("Unintentional integer overflow") Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com> Acked-by: Jose Abreu <joabreu@synopsys.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: phy: DP83TC811: Fix SGMII enable/disableDan Murphy1-11/+9
If SGMII was selected in the DT then the device should write the SGMII enable bit. If SGMII is not selected in the DT then the SGMII bit should be disabled. Signed-off-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03net: phy: DP83TC811: Add INT_STAT3Dan Murphy1-0/+26
Add INT_STAT3 interrupt setting and clearing support. Signed-off-by: Dan Murphy <dmurphy@ti.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-03Merge ra.kernel.org:/pub/scm/linux/kernel/git/davem/netDavid S. Miller163-579/+1469
Simple overlapping changes in stmmac driver. Adjust skb_gro_flush_final_remcsum function signature to make GRO list changes in net-next, as per Stephen Rothwell's example merge resolution. Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02Merge branch 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/mdLinus Torvalds2-3/+12
Pull MD fixes from Shaohua Li: "Two small fixes for MD: - an error handling fix from me - a recover bug fix for raid10 from BingJing" * 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/shli/md: md/raid10: fix that replacement cannot complete recovery after reassemble MD: cleanup resources in failure
2018-07-02Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netLinus Torvalds55-198/+414
Pull networking fixes from David Miller: 1) Verify netlink attributes properly in nf_queue, from Eric Dumazet. 2) Need to bump memory lock rlimit for test_sockmap bpf test, from Yonghong Song. 3) Fix VLAN handling in lan78xx driver, from Dave Stevenson. 4) Fix uninitialized read in nf_log, from Jann Horn. 5) Fix raw command length parsing in mlx5, from Alex Vesker. 6) Cleanup loopback RDS connections upon netns deletion, from Sowmini Varadhan. 7) Fix regressions in FIB rule matching during create, from Jason A. Donenfeld and Roopa Prabhu. 8) Fix mpls ether type detection in nfp, from Pieter Jansen van Vuuren. 9) More bpfilter build fixes/adjustments from Masahiro Yamada. 10) Fix XDP_{TX,REDIRECT} flushing in various drivers, from Jesper Dangaard Brouer. 11) fib_tests.sh file permissions were broken, from Shuah Khan. 12) Make sure BH/preemption is disabled in data path of mac80211, from Denis Kenzior. 13) Don't ignore nla_parse_nested() return values in nl80211, from Johannes berg. 14) Properly account sock objects ot kmemcg, from Shakeel Butt. 15) Adjustments to setting bpf program permissions to read-only, from Daniel Borkmann. 16) TCP Fast Open key endianness was broken, it always took on the host endiannness. Whoops. Explicitly make it little endian. From Yuching Cheng. 17) Fix prefix route setting for link local addresses in ipv6, from David Ahern. 18) Potential Spectre v1 in zatm driver, from Gustavo A. R. Silva. 19) Various bpf sockmap fixes, from John Fastabend. 20) Use after free for GRO with ESP, from Sabrina Dubroca. 21) Passing bogus flags to crypto_alloc_shash() in ipv6 SR code, from Eric Biggers. * git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits) qede: Adverstise software timestamp caps when PHC is not available. qed: Fix use of incorrect size in memcpy call. qed: Fix setting of incorrect eswitch mode. qed: Limit msix vectors in kdump kernel to the minimum required count. ipvlan: call dev_change_flags when ipvlan mode is reset ipv6: sr: fix passing wrong flags to crypto_alloc_shash() net: fix use-after-free in GRO with ESP tcp: prevent bogus FRTO undos with non-SACK flows bpf: sockhash, add release routine bpf: sockhash fix omitted bucket lock in sock_close bpf: sockmap, fix smap_list_map_remove when psock is in many maps bpf: sockmap, fix crash when ipv6 sock is added net: fib_rules: bring back rule_exists to match rule during add hv_netvsc: split sub-channel setup into async and sync net: use dev_change_tx_queue_len() for SIOCSIFTXQLEN atm: zatm: Fix potential Spectre v1 s390/qeth: consistently re-enable device features s390/qeth: don't clobber buffer on async TX completion s390/qeth: avoid using is_multicast_ether_addr_64bits on (u8 *)[6] s390/qeth: fix race when setting MAC address ...
2018-07-02net: hns3: modify hnae_ to hnae3_Peng Li11-336/+343
For consistency, prefix hnae_ should be modified to hnae3_. Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: use dma_zalloc_coherent instead of kzalloc/dma_map_singleHuazhong Tan3-49/+28
Reference to Documentation/DMA-API-HOWTO.txt, Streaming DMA mappings which are usually mapped for one DMA transfer, Network card DMA ring descriptors should use Consistent DMA mappings. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: give default option while dependency HNS3 setHuazhong Tan1-6/+9
Give default option for HNS3_HCLGE and HNS3_ENET will be helpful, while dependency HNS3 is set. Meanwhile, use "if HNS3" section instead of all the "depends on HNS3". Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: remove some unused members of some structuresHuazhong Tan4-5/+0
Some members in struct hns3_enet_tqp_vector, struct hnae3_client and struct hnae3_ae_algo are unused. This patch removes them. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: remove a redundant hclge_cmd_csq_doneHuazhong Tan1-6/+6
Set complete in the first hclge_cmd_csq_done of hclge_cmd_send, and check if complete later, unnecessary to do hclge_cmd_csq_done again. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: simplify hclge_cmd_csq_cleanHuazhong Tan1-16/+5
csq is used as a ring buffer, the value of the desc will be replaced in next use. This patch removes the unnecessary memset, and just updates the next_to_clean. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: remove some redundant assignmentsHuazhong Tan2-10/+0
Remove some redundant assignments. desc->flag = cpu_to_le16(HCLGE_CMD_FLAG_NO_INTR | HCLGE_CMD_FLAG_IN) has set bit HCLGE_CMD_FLAG_WR to zero, so does others. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: remove useless code in hclge_cmd_sendHuazhong Tan1-4/+2
There are some useless type cast, print in hclge_cmd_send. This patch removes them. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: hns3: remove unused hclge_ring_to_dma_dirHuazhong Tan1-2/+1
hclge_ring_to_dma_dir is unused anywhere. This patch removes it. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02atm: zatm: remove redundant pointer zatm_devColin Ian King1-2/+0
Pointer zatm_dev is being assigned but is never used hence it is redundant and can be removed. Cleans up clang warning: warning: variable 'zatm_dev' set but not used [-Wunused-but-set-variable] Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: phy: realtek: add support for RTL8211CHeiner Kallweit1-0/+17
RTL8211C has an issue when operating in Gigabit slave mode, therefore genphy driver can't be used. See also this U-boot change. https://lists.denx.de/pipermail/u-boot/2016-March/249712.html Add a PHY driver for this chip with the quirk to force Gigabit master mode. As a note: This will make it impossible to connect two network ports directly which both are driven by a RTl8211C. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02TTY: isdn: Replace strncpy with memcpyGuenter Roeck1-2/+2
gcc 8.1.0 complains: drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_suspend.isra.1': drivers/isdn/i4l/isdn_tty.c:790:3: warning: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length drivers/isdn/i4l/isdn_tty.c:778:6: note: length computed here drivers/isdn/i4l/isdn_tty.c: In function 'isdn_tty_resume': drivers/isdn/i4l/isdn_tty.c:880:3: warning: 'strncpy' output truncated before terminating nul copying as many bytes from a string as its length drivers/isdn/i4l/isdn_tty.c:817:6: note: length computed here Using strncpy() is indeed less than perfect since the length of data to be copied has already been determined with strlen(). Replace strncpy() with memcpy() to address the warning and optimize the code a little. Signed-off-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: phy: realtek: add missing entry for RTL8211 to mdio_device_id tableHeiner Kallweit1-0/+1
When adding support for RTL8211 I forgot to update the mdio_device_id table. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Fixes: d241d4aac93f ("net: phy: realtek: add support for RTL8211") Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02r8169: remove old PHY reset hackHeiner Kallweit1-56/+1
This hack (affecting the non-PCIe models only) was introduced in 2004 to deal with link negotiation failures in 1GBit mode. Based on a comment in the r8169 vendor driver I assume the issue affects RTL8169sb in combination with particular 1GBit switch models. Resetting the PHY every 10s and hoping that one fine day we will make it to establish the link seems to be very hacky to me. I'd say: If 1GBit doesn't work reliably in a users environment then the user should remove 1GBit from the advertised modes, e.g. by using ethtool -s <if> advertise <10/100 modes> If the issue affects one chip version only and that with most link partners, then we could also think of removing 1GBit from the advertised modes for this chip version in the driver. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02qede: Adverstise software timestamp caps when PHC is not available.Sudarsana Reddy Kalluru1-2/+8
When ptp clock is not available for a PF (e.g., higher PFs in NPAR mode), get-tsinfo() callback should return the software timestamp capabilities instead of returning the error. Fixes: 4c55215c ("qede: Add driver support for PTP") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02qed: Fix use of incorrect size in memcpy call.Sudarsana Reddy Kalluru1-4/+4
Use the correct size value while copying chassis/port id values. Fixes: 6ad8c632e ("qed: Add support for query/config dcbx.") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02qed: Fix setting of incorrect eswitch mode.Sudarsana Reddy Kalluru2-3/+18
By default, driver sets the eswitch mode incorrectly as VEB (virtual Ethernet bridging). Need to set VEB eswitch mode only when sriov is enabled, and it should be to set NONE by default. The patch incorporates this change. Fixes: 0fefbfbaa ("qed*: Management firmware - notifications and defaults") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02qed: Limit msix vectors in kdump kernel to the minimum required count.Sudarsana Reddy Kalluru1-0/+8
Memory size is limited in the kdump kernel environment. Allocation of more msix-vectors (or queues) consumes few tens of MBs of memory, which might lead to the kdump kernel failure. This patch adds changes to limit the number of MSI-X vectors in kdump kernel to minimum required value (i.e., 2 per engine). Fixes: fe56b9e6a ("qed: Add module with basic common support") Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com> Signed-off-by: Michal Kalderon <Michal.Kalderon@cavium.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02ipvlan: call dev_change_flags when ipvlan mode is resetHangbin Liu1-8/+28
After we change the ipvlan mode from l3 to l2, or vice versa, we only reset IFF_NOARP flag, but don't flush the ARP table cache, which will cause eth->h_dest to be equal to eth->h_source in ipvlan_xmit_mode_l2(). Then the message will not come out of host. Here is the reproducer on local host: ip link set eth1 up ip addr add 192.168.1.1/24 dev eth1 ip link add link eth1 ipvlan1 type ipvlan mode l3 ip netns add net1 ip link set ipvlan1 netns net1 ip netns exec net1 ip link set ipvlan1 up ip netns exec net1 ip addr add 192.168.2.1/24 dev ipvlan1 ip route add 192.168.2.0/24 via 192.168.1.2 ping 192.168.2.2 -c 2 ip netns exec net1 ip link set ipvlan1 type ipvlan mode l2 ping 192.168.2.2 -c 2 Add the same configuration on remote host. After we set the mode to l2, we could find that the src/dst MAC addresses are the same on eth1: 21:26:06.648565 00:b7:13:ad:d3:05 > 00:b7:13:ad:d3:05, ethertype IPv4 (0x0800), length 98: (tos 0x0, ttl 64, id 58356, offset 0, flags [DF], proto ICMP (1), length 84) 192.168.2.1 > 192.168.2.2: ICMP echo request, id 22686, seq 1, length 64 Fix this by calling dev_change_flags(), which will call netdevice notifier with flag change info. v2: a) As pointed out by Wang Cong, check return value for dev_change_flags() when change dev flags. b) As suggested by Stefano and Sabrina, move flags setting before l3mdev_ops. So we don't need to redo ipvlan_{, un}register_nf_hook() again in err path. Reported-by: Jianlin Shi <jishi@redhat.com> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Reviewed-by: Sabrina Dubroca <sd@queasysnail.net> Fixes: 2ad7bf3638411 ("ipvlan: Initial check-in of the IPVLAN driver.") Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02netdevsim: fix sa_idx out of bounds checkColin Ian King1-1/+1
Currently if sa_idx is equal to NSIM_IPSEC_MAX_SA_COUNT then an out-of-bounds read on ipsec->sa will occur. Fix the incorrect bounds check by using >= rather than >. Detected by CoverityScan, CID#1470226 ("Out-of-bounds-read") Fixes: 7699353da875 ("netdevsim: add ipsec offload testing") Signed-off-by: Colin Ian King <colin.king@canonical.com> Acked-by: Shannon Nelson <shannon.nelson@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-02net: fix use-after-free in GRO with ESPSabrina Dubroca2-4/+2
Since the addition of GRO for ESP, gro_receive can consume the skb and return -EINPROGRESS. In that case, the lower layer GRO handler cannot touch the skb anymore. Commit 5f114163f2f5 ("net: Add a skb_gro_flush_final helper.") converted some of the gro_receive handlers that can lead to ESP's gro_receive so that they wouldn't access the skb when -EINPROGRESS is returned, but missed other spots, mainly in tunneling protocols. This patch finishes the conversion to using skb_gro_flush_final(), and adds a new helper, skb_gro_flush_final_remcsum(), used in VXLAN and GUE. Fixes: 5f114163f2f5 ("net: Add a skb_gro_flush_final helper.") Signed-off-by: Sabrina Dubroca <sd@queasysnail.net> Reviewed-by: Stefano Brivio <sbrivio@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-07-01Merge tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/stagingLinus Torvalds6-6/+9
Pull staging/IIO fixes from Greg KH: "Here are a few small staging and IIO driver fixes for 4.18-rc3. Nothing major or big, all just fixes for reported problems since 4.18-rc1. All of these have been in linux-next this week with no reported problems" * tag 'staging-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: staging: android: ion: Return an ERR_PTR in ion_map_kernel staging: comedi: quatech_daqp_cs: fix no-op loop daqp_ao_insn_write() iio: imu: inv_mpu6050: Fix probe() failure on older ACPI based machines iio: buffer: fix the function signature to match implementation iio: mma8452: Fix ignoring MMA8452_INT_DRDY iio: tsl2x7x/tsl2772: avoid potential division by zero iio: pressure: bmp280: fix relative humidity unit
2018-07-01Merge tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/ttyLinus Torvalds4-27/+35
Pull tty/serial fixes from Greg KH: "Here are five fixes for the tty core and some serial drivers. The tty core ones fix some security and other issues reported by the syzbot that I have taken too long in responding to (sorry Tetsuo!). The 8350 serial driver fix resolves an issue of devices that used to work properly stopping working as they shouldn't have been added to a blacklist. All of these have been in linux-next for a few days with no reported issues" * tag 'tty-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: vt: prevent leaking uninitialized data to userspace via /dev/vcs* serdev: fix memleak on module unload serial: 8250_pci: Remove stalled entries in blacklist n_tty: Access echo_* variables carefully. n_tty: Fix stall at n_tty_receive_char_special().
2018-07-01Merge tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usbLinus Torvalds26-65/+369
Pull USB fixes from Greg KH: "Here is a number of USB gadget and other driver fixes for 4.18-rc3. There's a bunch of them here, most of them being gadget driver and xhci host controller fixes for reported issues (as normal), but there are also some new device ids, and some fixes for the typec code. There is an acpi core patch in here that was acked by the acpi maintainer as it is needed for the typec fixes in order to properly solve a problem in that driver. All of these have been in linux-next this week with no reported issues" * tag 'usb-4.18-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (33 commits) usb: chipidea: host: fix disconnection detect issue usb: typec: tcpm: fix logbuffer index is wrong if _tcpm_log is re-entered typec: tcpm: Fix a msecs vs jiffies bug NFC: pn533: Fix wrong GFP flag usage usb: cdc_acm: Add quirk for Uniden UBC125 scanner staging/typec: fix tcpci_rt1711h build errors usb: typec: ucsi: Fix for incorrect status data issue usb: typec: ucsi: acpi: Workaround for cache mode issue acpi: Add helper for deactivating memory region usb: xhci: increase CRS timeout value usb: xhci: tegra: fix runtime PM error handling usb: xhci: remove the code build warning xhci: Fix kernel oops in trace_xhci_free_virt_device xhci: Fix perceived dead host due to runtime suspend race with event handler dwc2: gadget: Fix ISOC IN DDMA PID bitfield value calculation usb: gadget: dwc2: fix memory leak in gadget_init() usb: gadget: composite: fix delayed_status race condition when set_interface usb: dwc2: fix isoc split in transfer with no data usb: dwc2: alloc dma aligned buffer for isoc split in usb: dwc2: fix the incorrect bitmaps for the ports of multi_tt hub ...
2018-07-01Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpfDavid S. Miller2-15/+5
Daniel Borkmann says: ==================== pull-request: bpf 2018-07-01 The following pull-request contains BPF updates for your *net* tree. The main changes are: 1) A bpf_fib_lookup() helper fix to change the API before freeze to return an encoding of the FIB lookup result and return the nexthop device index in the params struct (instead of device index as return code that we had before), from David. 2) Various BPF JIT fixes to address syzkaller fallout, that is, do not reject progs when set_memory_*() fails since it could still be RO. Also arm32 JIT was not using bpf_jit_binary_lock_ro() API which was an issue, and a memory leak in s390 JIT found during review, from Daniel. 3) Multiple fixes for sockmap/hash to address most of the syzkaller triggered bugs. Usage with IPv6 was crashing, a GPF in bpf_tcp_close(), a missing sock_map_release() routine to hook up to callbacks, and a fix for an omitted bucket lock in sock_close(), from John. 4) Two bpftool fixes to remove duplicated error message on program load, and another one to close the libbpf object after program load. One additional fix for nfp driver's BPF offload to avoid stopping offload completely if replace of program failed, from Jakub. 5) Couple of BPF selftest fixes that bail out in some of the test scripts if the user does not have the right privileges, from Jeffrin. 6) Fixes in test_bpf for s390 when CONFIG_BPF_JIT_ALWAYS_ON is set where we need to set the flag that some of the test cases are expected to fail, from Kleber. 7) Fix to detangle BPF_LIRC_MODE2 dependency from CONFIG_CGROUP_BPF since it has no relation to it and lirc2 users often have configs without cgroups enabled and thus would not be able to use it, from Sean. 8) Fix a selftest failure in sockmap by removing a useless setrlimit() call that would set a too low limit where at the same time we are already including bpf_rlimit.h that does the job, from Yonghong. 9) Fix BPF selftest config with missing missing NET_SCHED, from Anders. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-30Merge tag 'for-linus-20180629' of git://git.kernel.dk/linux-blockLinus Torvalds3-7/+7
Pull block fixes from Jens Axboe: "Small set of fixes for this series. Mostly just minor fixes, the only oddball in here is the sg change. The sg change came out of the stall fix for NVMe, where we added a mempool and limited us to a single page allocation. CONFIG_SG_DEBUG sort-of ruins that, since we'd need to account for that. That's actually a generic problem, since lots of drivers need to allocate SG lists. So this just removes support for CONFIG_SG_DEBUG, which I added back in 2007 and to my knowledge it was never useful. Anyway, outside of that, this pull contains: - clone of request with special payload fix (Bart) - drbd discard handling fix (Bart) - SATA blk-mq stall fix (me) - chunk size fix (Keith) - double free nvme rdma fix (Sagi)" * tag 'for-linus-20180629' of git://git.kernel.dk/linux-block: sg: remove ->sg_magic member drbd: Fix drbd_request_prepare() discard handling blk-mq: don't queue more if we get a busy return block: Fix cloning of requests with a special payload nvme-rdma: fix possible double free of controller async event buffer block: Fix transfer when chunk sectors exceeds max
Copyright © 1996 – 2023 Jason A. Donenfeld. All Rights Reverse Engineered.