| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
To make the code easier to read use macros for the bit masks.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20211009113707.17568-2-alistair@alistair23.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The created rmi device is orphan, which breaks the real device
hierarchy, and can cause some trouble, especially during suspend
and resume sequences. E.g. in case of I2C, rmi dev should be child
of the I2C client device.
Fix this, assigning the transport device as parent of the rmi device.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1635514971-18415-1-git-send-email-loic.poulain@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Fujitsu Lifebook T725 laptop requires, like a few other similar
models, the nomux and notimeout options to probe the touchpad
properly. This patch adds the corresponding quirk entries.
BugLink: https://bugzilla.suse.com/show_bug.cgi?id=1191980
Tested-by: Neal Gompa <ngompa13@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20211103070019.13374-1-tiwai@suse.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
According to the datasheet "The CAP1206 is pin- and register-compatible
with the CAP1106, with the exception of the GAIN[1:0] bits and ALT_POL
bit"(57). So, this patch aims to disable them as they are no longer
used.
Signed-off-by: Jesse Taube <mr.bossman075@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x firmware can be updated, this is used when switching between
different modes of operation of the touch surface, e.g. glove operation.
This patch implements the firmware update mechanism triggered by a write
into an sysfs attribute.
The firmware itself is distributed as an intel hex file with non-standard
types. The first two lines are of type 0xad, which indicates the start of
DataFlash payload, that is always at address 0xf000 on the ili251x, so it
can be dropped, and 0xac which indicates the position of firmware info in
the Application payload, that is always at address 0x2020 on the ili251x
and we do not care. The rest of the firmware is data of type 0x00, and we
care about that. To convert the firmware hex file into something usable
by the kernel, remove the first two lines and then use ihex2fw:
$ tail -n +3 input.hex > temp.hex
$ ./tools/firmware/ihex2fw temp.hex firmware/ilitek/ili251x.bin
To trigger the firmware update, place firmware file ilitek/ili251x.bin
into /lib/firmware/, write into firmware_update sysfs attribute and wait
about 30-40 seconds. The firmware update is slow. Afterward, verify the
firmware_version and mode sysfs attributes to check whether the firmware
got updated and the controller switched back to application (AP) mode by
reading out 'mode' attribute in sysfs.
Note that the content of firmware_version, e.g. 0600.0005.abcd.aa04 can
be matched to the content of the firmware hex file. The first four bytes,
0x06 0x00 0x00 0x05 can be found at ^:102030 00 05000006, the next four
bytes 0xab 0xcd 0xaa 0x04 at ^:10F000 00 nnnnnnnn ABCDAA04.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-3-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x firmware protocol permits readout of firmware version,
protocol version, mcu version and current mode (application, boot
loader, forced update). These information are useful when updating
the firmware on the il251x, e.g. to avoid updating the same firmware
into the device multiple times. The locking is now necessary to avoid
races between interrupt handler and the sysfs readouts.
Note that the protocol differs considerably between the ili2xxx devices,
this patch therefore implements this functionality only for ili251x that
I can test.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-2-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x firmware protocol permits readout of panel resolution,
implement this, but make it possible to override this value using
DT bindings. This way, older DTs which contain touchscreen-size-x
and touchscreen-size-y properties will behave just like before and
new DTs may avoid specifying these for ILI251x.
Note that the command format is different on other controllers, so
this functionality is isolated to ILI251x.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20210831202506.181927-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
On some devices, e.g. Sony Xperia M4 Aqua, warm reset is used to reboot
device into bootloader and recovery mode. Instead of always doing hard
reset, add a check on reboot_mode for possible warm reset.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Luca Weiss <luca@z3ntu.xyz>
Link: https://lore.kernel.org/r/20210714095850.27185-3-shawn.guo@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20210916170514.137977-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We are using devm_input_allocate_device() that already sets parent
of the input device, there is no need to do that again.
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/YWpiZqrfC9+GQsM4@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Change the comment to a normal (non-kernel-doc) comment to avoid
these kernel-doc warnings:
max8925_onkey.c:2: warning: This comment starts with '/**', but isn't a kernel-doc comment. Refer Documentation/doc-guide/kernel-doc.rst
* MAX8925 ONKEY driver
max8925_onkey.c:2: warning: missing initial short description on line:
* MAX8925 ONKEY driver
Fixes: 3734574cac100 ("Input: enable onkey driver of max8925")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211002045943.9406-1-rdunlap@infradead.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When request_irq() returns -EPORBE_DEFER we should abort probe and try
again later instead of trying to engage IRQ trigger workaround.
Link: https://lore.kernel.org/r/20210910045039.4020199-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of manipulating capability bits directly use
input_set_capability(). Also stop setting EV_ABS explicitly as
input_set_abs_params() does it for us.
Link: https://lore.kernel.org/r/20210910045039.4020199-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Set input device's bus type as BUS_SPI and use model as product ID.
Link: https://lore.kernel.org/r/20210910045039.4020199-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
At the moment the touch keys have key codes assigned from the device
tree. In some cases, users might want to change the key code from
userspace. There is existing functionality for this in the input core
using the EVIOCSKEYCODE ioctl, which is integrated for example into udev.
Make it possible to use this functionality for tm2-touchkey by simply
making the input core aware of the array that holds the keycodes.
Similar code also exists in mcs_touchkey and mpr121_touchkey.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-2-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Report the index of pressed touch key as MSC_SCAN code to userspace
so it is possible to identify which of the keys was pressed (not
just the function that is currently assigned to the key).
This is done similarly also in mcs_touchkey and mpr121_touchkey.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20211013112305.41574-1-stephan@gerhold.net
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This fixes the following warning from sparse:
CC [M] drivers/input/misc/adxl34x.o
CHECK drivers/input/misc/adxl34x.c
drivers/input/misc/adxl34x.c:245:29: warning: cast to restricted __le16
drivers/input/misc/adxl34x.c:248:29: warning: cast to restricted __le16
drivers/input/misc/adxl34x.c:251:29: warning: cast to restricted __le16
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/YWZIjb91d6aAwgss@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
By using managed resources (devm) we are able to streamline error handling
in probe and remove most of the custom remove method.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/YWZGKWgdarGtvtYA@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of manually toggling interrupt as wakeup source in suspend/resume
methods, let's declare keypad interrupt and wakeup interrupt and leave the
rest to the PM core.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20211012013735.3523140-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Also drop parenthesis around macros that do not use expressions as they are
not needed.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20211012013735.3523140-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of guarding suspend/resume methods with #ifdef CONFIG_PM
let's mark them as __maybe_unused as this allows better compile
coverage.
Acked-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20211012013735.3523140-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Up to now tsc200x_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211012153945.2651412-7-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Up to now adxl34x_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of i2c and spi remove callbacks is ignored anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20211012153945.2651412-6-u.kleine-koenig@pengutronix.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The device may take up to 100ms to become responsive during probe, so
prefer asynchronous probing to avoid delaying the rest of the system.
Suggested-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: John Keeping <john@metanate.com>
Link: https://lore.kernel.org/r/20211007111217.1935858-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
I have a ST1633 touch controller which fails to probe due to a timeout
waiting for the controller to become ready. Increasing the minimum
delay to 100ms ensures that the probe sequence completes successfully.
The ST1633 datasheet says nothing about the maximum delay here and the
ST1232 I2C protocol document says "wait until" with no notion of a
timeout.
Since this only runs once during probe, being generous with the timout
seems reasonable and most likely the device will become ready
eventually.
(It may be worth noting that I saw this issue with a PREEMPT_RT patched
kernel which probably has tighter wakeups from usleep_range() than other
preemption models.)
Fixes: f605be6a57b4 ("Input: st1232 - wait until device is ready before reading resolution")
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20210929152609.2421483-1-john@metanate.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Overlapping input and output arguments to snprintf() are
undefined behavior in C99:
drivers/input/joystick/analog.c: In function 'analog_name':
drivers/input/joystick/analog.c:428:3: error: 'snprintf' argument 4 overlaps destination object 'analog' [-Werror=restrict]
428 | snprintf(analog->name, sizeof(analog->name), "%s %d-hat",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
429 | analog->name, hweight16(analog->mask & ANALOG_HATS_ALL));
| ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/input/joystick/analog.c:420:40: note: destination object referenced by 'restrict'-qualified argument 1 was declared here
420 | static void analog_name(struct analog *analog)
| ~~~~~~~~~~~~~~~^~~~~~
Change this function to use the simpler seq_buf interface instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210927101416.1569609-1-arnd@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Currently autoloading for SPI devices does not use the DT ID table, it uses
SPI modalises. Supporting OF modalises is going to be difficult if not
impractical, an attempt was made but has been reverted, so ensure that
module autoloading works for this driver by adding a SPI device ID table.
Fixes: 96c8395e2166 ("spi: Revert modalias changes")
Signed-off-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20210927134104.38648-1-broonie@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125954.533-1-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125212.95-3-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The helper function devm_add_action_or_reset() will internally
call devm_add_action(), and if devm_add_action() fails then it will
execute the action mentioned and return the error code. So
use devm_add_action_or_reset() instead of devm_add_action()
to simplify the error handling, reduce the code.
Signed-off-by: Cai Huoqing <caihuoqing@baidu.com>
Link: https://lore.kernel.org/r/20210922125212.95-2-caihuoqing@baidu.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some Goodix touchscreen controllers, such as for example the GT912,
don't have flash-storage for their firmware.
These models require the OS to load the firmware at runtime, as well as
some other special handling. Add support for this to the goodix driver.
This patch was developed and tested on a Glavey TM800A550L tablet.
Note the "goodix,main-clk" and "firmware-name" device-properties used
by the new code are *not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.
Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this properties for now is purely a kernel-internal thing and
the name/working of the properties may still be changed for now.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-7-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The config which needs to be send to the controller on some device-models
is model-specific. Allow specifying a model-specific filename through
a device-property, rather then always using a fixed filename.
Note the "goodix,config-name" device-property used by this is
*not* documented in the
Documentation/devicetree/bindings/input/touchscreen/goodix.yaml
device-tree bindings for now.
Not documenting these is intentional. This is done because this code has
only been tested on x86/ACPI so far, where devicetree is not used.
Instead these properties are set through a software-fwnode attached to the
device by the drivers/platform/x86/touchscreen_dmi.c code. This means that
the use of this property for now is purely a kernel-internal thing and
the name/working of the property may still be changed for now.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-6-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Make the goodix_i2c_read() and goodix_i2c_write*() helpers log errors
themselves. This allows removing all the error logging from their callers.
This already results in a nice cleanup with the current code and it also
helps to make the upcoming support for controllers without flash cleaner.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-5-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Refactor reset handling a bit, change the main reset handler
into a new goodix_reset_no_int_sync() helper and add a
goodix_reset() wrapper which calls goodix_int_sync()
separately.
Also push the dev_err() call on reset failure into the
goodix_reset_no_int_sync() and goodix_int_sync() functions,
so that we don't need to have separate dev_err() calls in
all their callers.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-4-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add a goodix.h header file, and move the register definitions,
and struct declarations there and add prototypes for various
helper functions.
This is a preparation patch for adding support for controllers
without flash, which need to have their firmware uploaded and
need some other special handling too.
Since MAINTAINERS needs updating because of this change anyways,
also add myself as co-maintainer.
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-3-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Change the type of the goodix_i2c_write() len parameter to from 'unsigned'
to 'int' to avoid bare use of 'unsigned', changing it to 'int' makes
goodix_i2c_write()' prototype consistent with goodix_i2c_read().
Reviewed-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20210920150643.155872-2-hdegoede@redhat.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
There is a spelling mistake in the name of a joystick. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20210920184748.18519-1-colin.king@canonical.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
As noted in the "Deprecated Interfaces, Language Features, Attributes,
and Conventions" documentation [1], size calculations (especially
multiplication) should not be performed in memory allocator (or similar)
function arguments due to the risk of them overflowing. This could lead
to values wrapping around and a smaller allocation being made than the
caller was expecting. Using those allocations could lead to linear
overflows of heap memory and other misbehaviors.
So, use the struct_size() helper to do the arithmetic instead of the
argument "size + count * size" in the kzalloc() function.
[1] https://www.kernel.org/doc/html/v5.14/process/deprecated.html#open-coded-arithmetic-in-allocator-arguments
Signed-off-by: Len Baker <len.baker@gmx.com>
Link: https://lore.kernel.org/r/20210911112716.10067-1-len.baker@gmx.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This adds support for Cypress StreetFighter touchkey controllers such
as sf3155. This driver supports managing regulators and generating
input events.
Due to lack of documentation, this driver is entirely based on
information gathered from a driver written for an old Android kernel
fork[1][2].
[1] https://github.com/LineageOS/android_kernel_xiaomi_msm8996/blob/lineage-18.1/drivers/input/touchscreen/cyttsp_button.c
[2] https://github.com/LineageOS/android_kernel_xiaomi_msm8996/blob/lineage-18.1/arch/arm/boot/dts/qcom/a4-msm8996-mtp.dtsi#L291-L314
Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com>
Link: https://lore.kernel.org/r/20210907174341.422013-2-y.oudjana@protonmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This simplies the code a lot and fixes some potential resource leaks in
the error return paths.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210907200726.2034962-4-daniel@zonque.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The functions in the platform data struct to initialize, cleanup and
apply custom filters are not in use by any mainline board.
Remove support for them to pave the road for more cleanups to come.
The enum was moved as it has no users outside of the driver code
itself.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210907200726.2034962-3-daniel@zonque.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This will make the code a bit more terse.
No functional change intended.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Marco Felsch <m.felsch@pengutronix.de>
Link: https://lore.kernel.org/r/20210907200726.2034962-2-daniel@zonque.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
platform_get_irq() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add support reading device ID when controller is in bootloader mode, which
may happen if firmware update has been interrupted.
Signed-off-by: simba.hsu <simba.hsu@rad-ic.com>
Link: https://lore.kernel.org/r/20210818063644.8654-1-simba.hsu@rad-ic.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The function cpcap_power_button_probe() does not perform
sufficient error checking after executing platform_get_irq(),
thus fix it.
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Link: https://lore.kernel.org/r/20210802121740.8700-1-tangbin@cmss.chinamobile.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
As the ADC ladder input driver does not have any code or data located in
initmem, there is no need to annotate the adc_keys_driver structure with
__refdata. Drop the annotation, to avoid suppressing future section
warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/7091e8213602be64826fd689a7337246d218f3b1.1626255421.git.geert+renesas@glider.be
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
Alistair Francis
Marek Vasut
Phoenix Huang
Loic Poulain
Takashi Iwai
Jesse Taube
Shawn Guo
Krzysztof Kozlowski
Dmitry Torokhov
Randy Dunlap
Stephan Gerhold
Uwe Kleine-König
John Keeping
Arnd Bergmann
Mark Brown
Cai Huoqing
Hans de Goede
Colin Ian King
Len Baker
Yassine Oudjana
Daniel Mack
Arvind Yadav
simba.hsu
Tang Bin
Geert Uytterhoeven