| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.
Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.
Fixes: 4607f6d26950 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: Nir Dotan <nird@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().
Drop the reference when this unlikely error is hit.
Fixes: 1c30d1836aeb ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.
Fix by removing these warnings for now.
Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.
Fixes: 6e6030bd5412 ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the network stack calls .send_pkt()/.cancel_pkt() during .release(),
a struct vhost_vsock use-after-free is possible. This occurs because
.release() does not wait for other CPUs to stop using struct
vhost_vsock.
Switch to an RCU-enabled hashtable (indexed by guest CID) so that
.release() can wait for other CPUs by calling synchronize_rcu(). This
also eliminates vhost_vsock_lock acquisition in the data path so it
could have a positive effect on performance.
This is CVE-2018-14625 "kernel: use-after-free Read in vhost_transport_send_pkt".
Cc: stable@vger.kernel.org
Reported-and-tested-by: syzbot+bd391451452fb0b93039@syzkaller.appspotmail.com
Reported-by: syzbot+e3e074963495f92a89ed@syzkaller.appspotmail.com
Reported-by: syzbot+d5a0a170c5069658b141@syzkaller.appspotmail.com
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
While ccw_io_helper() seems like intended to be exclusive in a sense that
it is supposed to facilitate I/O for at most one thread at any given
time, there is actually nothing ensuring that threads won't pile up at
vcdev->wait_q. If they do, all threads get woken up and see the status
that belongs to some other request than their own. This can lead to bugs.
For an example see:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1788432
This race normally does not cause any problems. The operations provided
by struct virtio_config_ops are usually invoked in a well defined
sequence, normally don't fail, and are normally used quite infrequent
too.
Yet, if some of the these operations are directly triggered via sysfs
attributes, like in the case described by the referenced bug, userspace
is given an opportunity to force races by increasing the frequency of the
given operations.
Let us fix the problem by ensuring, that for each device, we finish
processing the previous request before starting with a new one.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Reported-by: Colin Ian King <colin.king@canonical.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-3-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Currently we have a race on vcdev->config in virtio_ccw_get_config() and
in virtio_ccw_set_config().
This normally does not cause problems, as these are usually infrequent
operations. However, for some devices writing to/reading from the config
space can be triggered through sysfs attributes. For these, userspace can
force the race by increasing the frequency.
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Cc: stable@vger.kernel.org
Message-Id: <20180925121309.58524-2-pasic@linux.ibm.com>
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
If a local process has closed a connected socket and hasn't received a
RST packet yet, then the socket remains in the table until a timeout
expires.
When a vhost_vsock instance is released with the timeout still pending,
the socket is never freed because vhost_vsock has already set the
SOCK_DONE flag.
Check if the close timer is pending and let it close the socket. This
prevents the race which can leak sockets.
Reported-by: Maximilian Riemensberger <riemensberger@cadami.net>
Cc: Graham Whaley <graham.whaley@gmail.com>
Signed-off-by: Stefan Hajnoczi <stefanha@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Intel Merrifield has a reduced size of FIFO used in iDMA 32-bit controller,
i.e. 512 bytes instead of 1024.
Fix this by partitioning it as 64 bytes per channel.
Note, in the future we might switch to 'fifo-size' property instead of
hard coded value.
Fixes: 199244d69458 ("dmaengine: dw: add support of iDMA 32-bit hardware")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Johan writes:
USB-serial fix for v4.20-rc6
Here's a fix for a reported USB-console regression in 4.18 which
revealed a long-standing bug in the console implementation.
The patch has been in linux-next over night with no reported issues.
Signed-off-by: Johan Hovold <johan@kernel.org>
* tag 'usb-serial-4.20-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: console: fix reported terminal settings
|
|
Fix activation helper which would return -ETIMEDOUT even if the last
retry attempt was successful.
Also change the semantics of the retries variable so that it actually
holds the number of retries (rather than tries).
Fixes: d2efbbd18b1e ("gnss: add driver for sirfstar-based receivers")
Cc: stable <stable@vger.kernel.org> # 4.19
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This patch is trying to fix KE issue due to
"BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198"
reported by Syzkaller scan."
[26364:syz-executor0][name:report8t]BUG: KASAN: global-out-of-bounds in param_set_kgdboc_var+0x194/0x198
[26364:syz-executor0][name:report&]Read of size 1 at addr ffffff900e44f95f by task syz-executor0/26364
[26364:syz-executor0][name:report&]
[26364:syz-executor0]CPU: 7 PID: 26364 Comm: syz-executor0 Tainted: G W 0
[26364:syz-executor0]Call trace:
[26364:syz-executor0][<ffffff9008095cf8>] dump_bacIctrace+Ox0/0x470
[26364:syz-executor0][<ffffff9008096de0>] show_stack+0x20/0x30
[26364:syz-executor0][<ffffff90089cc9c8>] dump_stack+Oxd8/0x128
[26364:syz-executor0][<ffffff90084edb38>] print_address_description +0x80/0x4a8
[26364:syz-executor0][<ffffff90084ee270>] kasan_report+Ox178/0x390
[26364:syz-executor0][<ffffff90084ee4a0>] _asan_report_loadi_noabort+Ox18/0x20
[26364:syz-executor0][<ffffff9008b092ac>] param_set_kgdboc_var+Ox194/0x198
[26364:syz-executor0][<ffffff900813af64>] param_attr_store+Ox14c/0x270
[26364:syz-executor0][<ffffff90081394c8>] module_attr_store+0x60/0x90
[26364:syz-executor0][<ffffff90086690c0>] sysfs_kl_write+Ox100/0x158
[26364:syz-executor0][<ffffff9008666d84>] kernfs_fop_write+0x27c/0x3a8
[26364:syz-executor0][<ffffff9008508264>] do_loop_readv_writev+0x114/0x1b0
[26364:syz-executor0][<ffffff9008509ac8>] do_readv_writev+0x4f8/0x5e0
[26364:syz-executor0][<ffffff9008509ce4>] vfs_writev+0x7c/Oxb8
[26364:syz-executor0][<ffffff900850ba64>] SyS_writev+Oxcc/0x208
[26364:syz-executor0][<ffffff90080883f0>] elO_svc_naked +0x24/0x28
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]The buggy address belongs to the variable:
[26364:syz-executor0][name:report&] kgdb_tty_line+Ox3f/0x40
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:report&]Memory state around the buggy address:
[26364:syz-executor0] ffffff900e44f800: 00 00 00 00 00 04 fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0] ffffff900e44f880: fa fa fa fa 00 fa fa fa fa fa fa fa 00 fa fa fa
[26364:syz-executor0]> ffffff900e44f900: fa fa fa fa 04 fa fa fa fa fa fa fa 00 00 00 00
[26364:syz-executor0][name:report&] ^
[26364:syz-executor0] ffffff900e44f980: 00 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
[26364:syz-executor0] ffffff900e44fa00: 04 fa fa fa fa fa fa fa 00 fa fa fa fa fa fa fa
[26364:syz-executor0][name:report&]
[26364:syz-executor0][name:panic&]Disabling lock debugging due to kernel taint
[26364:syz-executor0]------------[cut here]------------
After checking the source code, we've found there might be an out-of-bounds
access to "config[len - 1]" array when the variable "len" is zero.
Signed-off-by: Macpaul Lin <macpaul@gmail.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't allow USB3 U1 or U2 if the latency to wake up from the U-state
reaches the service interval for a periodic endpoint.
This is according to xhci 1.1 specification section 4.23.5.2 extra note:
"Software shall ensure that a device is prevented from entering a U-state
where its worst case exit latency approaches the ESIT."
Allowing too long exit latencies for periodic endpoint confuses xHC
internal scheduling, and new devices may fail to enumerate with a
"Not enough bandwidth for new device state" error from the host.
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Occasionally AMD SNPS 3.0 xHC does not respond to
CSS when set, also it does not flag anything on SRE and HCE
to point the internal xHC errors on USBSTS register. This stalls
the entire system wide suspend and there is no point in stalling
just because of xHC CSS is not responding.
To work around this problem, if the xHC does not flag
anything on SRE and HCE, we can skip the CSS
timeout and allow the system to continue the suspend. Once the
system resume happens we can internally reset the controller
using XHCI_RESET_ON_RESUME quirk
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Sandeep Singh <Sandeep.Singh@amd.com>
cc: Nehal Shah <Nehal-bakulchandra.Shah@amd.com>
Cc: <stable@vger.kernel.org>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When unloading the ast driver, a warning message is printed by
drm_mode_config_cleanup() because a reference is still held to one of
the drm_connector structs.
Correct this by calling drm_crtc_force_disable_all() in
ast_fbdev_destroy().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1e613f3c630c7bbc72e04a44b178259b9164d2f6.1543798395.git.sbobroff@linux.ibm.com
|
|
UAPI:
- Distinguish lease events from hotplug (Daniel)
Other:
- omap: Restore panel-dpi bus flags (Tomi)
- omap: Fix a couple of dsi issues (Sebastian)
Cc: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205201428.GA35447@art_vandelay
|
|
Fixes for 4.20:
- Fix banding regression on 6 bpc panels
- Vega20 fix for six 4k displays
- Fix LRU handling in ttm_buffer_object_transfer
- Use proper MC firmware for newer polaris variants
- Vega20 powerplay fixes
- VCN suspend/resume fix for PCO
- Misc other fixes
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205192934.2857-1-alexander.deucher@amd.com
|
|
- Several related to incorrect error checking/handling (Various)
- Prevent IRQ storm on MDP5 HDMI hotplug (Todor)
- Don't capture crash state if unsupported (Sharat)
- Properly grab vblank reference in atomic wait for commit done (Sean)
Cc: Sharat Masetty <smasetty@codeaurora.org>
Cc: Todor Tomov <todor.tomov@linaro.org>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20181205194207.GY154160@art_vandelay
|
|
Pull SCSI fixes from James Bottomley:
"Four obvious bug fixes. The vmw_pscsi is so old that it's amazing
no-one noticed before now"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: storvsc: Fix a race in sub-channel creation that can cause panic
scsi: vmw_pscsi: Rearrange code to avoid multiple calls to free_irq during unload
scsi: libiscsi: Fix NULL pointer dereference in iscsi_eh_session_reset
scsi: lpfc: fix block guard enablement on SLI3 adapters
|
|
A "short" ARS (address range scrub) instructs the platform firmware to
return known errors. In contrast, a "long" ARS instructs platform
firmware to arrange every data address on the DIMM to be read / checked
for poisoned data.
The conversion of the flags in commit d3abaf43bab8 "acpi, nfit: Fix
Address Range Scrub completion tracking", changed the meaning of passing
'0' to acpi_nfit_ars_rescan(). Previously '0' meant "not short", now '0'
is ARS_REQ_SHORT. Pass ARS_REQ_LONG to restore the expected scrub-type
behavior of user-initiated ARS sessions.
Fixes: d3abaf43bab8 ("acpi, nfit: Fix Address Range Scrub completion tracking")
Reported-by: Jacek Zloch <jacek.zloch@intel.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Reviewed-by: Dave Jiang <dave.jiang@intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit cfe30b872058 "libnvdimm, pmem: adjust for section collisions with
'System RAM'" enabled Linux to workaround occasions where platform
firmware arranges for "System RAM" and "Persistent Memory" to collide
within a single section boundary. Unfortunately, as reported in this
issue [1], platform firmware can inflict the same collision between
persistent memory regions.
The approach of interrogating iomem_resource does not work in this
case because platform firmware may merge multiple regions into a single
iomem_resource range. Instead provide a method to interrogate regions
that share the same parent bus.
This is a stop-gap until the core-MM can grow support for hotplug on
sub-section boundaries.
[1]: https://github.com/pmem/ndctl/issues/76
Fixes: cfe30b872058 ("libnvdimm, pmem: adjust for section collisions with...")
Cc: <stable@vger.kernel.org>
Reported-by: Patrick Geary <patrickg@supermicro.com>
Tested-by: Patrick Geary <patrickg@supermicro.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Pull block fixes from Jens Axboe:
"A bit earlier in the week as usual, but there's a fix here that should
go in sooner rather than later.
Under a combination of circumstance, the direct issue path in blk-mq
could corrupt data. This wasn't easy to hit, but the ones that are
affected by it, seem to hit it pretty easily. Full explanation in the
patch. None of the regular filesystem and storage testing has
triggered it, even though it's been around since 4.19-rc1.
Outside of that, whitelist trim tweak for certain Samsung devices for
libata"
* tag 'for-linus-20181205' of git://git.kernel.dk/linux-block:
blk-mq: fix corruption with direct issue
libata: whitelist all SAMSUNG MZ7KM* solid-state disks
|
|
When reading an extra descriptor, we need to properly check the minimum
and maximum size allowed, to prevent from invalid data being sent by a
device.
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Co-developed-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Hui Peng <benquike@gmail.com>
Signed-off-by: Mathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Johannes Berg:
====================
As it's been a while, we have various fixes for
* hwsim
* AP mode (client powersave related)
* CSA/FTM interaction
* a busy loop in IE handling
* and similar
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace vcn_v1_0_stop with vcn_v1_0_set_powergating_state during suspend,
to keep adev->vcn.cur_state update. It will fix VCN S3 hung issue.
Signed-off-by: James Zhu <James.Zhu@amd.com>
Reviewed-by: Leo Liu <leo.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull mfd bugfix from Lee Jones:
"Replace release function in cros_ec_dev"
* tag 'mfd-fixes-4.20' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
Revert "mfd: cros_ec: Use devm_kzalloc for private data"
|
|
This patch implements the process flow of SRQ asynchronous
event.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This patch implements the SRQ(Share Receive Queue) verbs
and update the poll cq verbs to deal with SRQ complentions.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This patch inits hem resource for SRQ table, includes
SRQWQE and SRQWQE index resource.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This patch configures the flags for enabling the
SRQ(Share Receive Queue) capacity as well as update the
verb of querying device for setting srq specifications.
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The thermal_zone_of_device_ops structure can be const as it is only
passed as the last argument of devm_thermal_zone_of_sensor_register
and the corresponding parameter is declared as const.
Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
serial8250_register_8250_port calls uart_config_port, which calls
config_port on the port before it tries to power on the port. So we need
the port to be on before calling serial8250_register_8250_port. Change
the code to always do a runtime resume in probe before registering port,
and always do a runtime suspend in remove.
This basically reverts the change in commit 68e5fc4a255a ("tty: serial:
8250_mtk: use pm_runtime callbacks for enabling"), but still use
pm_runtime callbacks.
Fixes: 68e5fc4a255a ("tty: serial: 8250_mtk: use pm_runtime callbacks for enabling")
Signed-off-by: Peter Shih <pihsun@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The USB-serial console implementation has never reported the actual
terminal settings used. Despite storing the corresponding cflags in its
struct console, these were never honoured on later tty open() where the
tty termios would be left initialised to the driver defaults.
Unlike the serial console implementation, the USB-serial code calls
subdriver open() already at console setup. While calling set_termios()
and write() before open() looks like it could work for some USB-serial
drivers, others definitely do not expect this, so modelling this after
serial core is going to be intrusive, if at all possible.
Instead, use a (renamed) tty helper to save the termios data used at
console setup so that the tty termios reflects the actual terminal
settings after a subsequent tty open().
Note that the calls to tty_init_termios() (tty_driver_install()) and
tty_save_termios() are serialised using the disconnect mutex.
This specifically fixes a regression that was triggered by a recent
change adding software flow control to the pl2303 driver: a getty trying
to disable flow control while leaving the baud rate unchanged would now
also set the baud rate to the driver default (prior to the flow-control
change this had been a noop).
Fixes: 7041d9c3f01b ("USB: serial: pl2303: add support for tx xon/xoff flow control")
Cc: stable <stable@vger.kernel.org> # 4.18
Cc: Florian Zumbiehl <florz@florz.de>
Reported-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
This reverts commit 3aa2177e47878f7e7616da8a2050c44f22301b6e.
That commit triggered a new WARN when unloading the module (see at the
end of the commit message). When a class_dev is embedded in a structure
then that class_dev is the thing that controls the lifetime of that
structure, for that reason device managed allocations can't be used here.
See Documentation/kobject.txt.
Revert the above patch, so the struct is allocated using kzalloc and we
have a release function for it that frees the allocated memory, otherwise
it is broken.
------------[ cut here ]------------
Device 'cros_ec' does not have a release() function, it is broken and must be fixed.
WARNING: CPU: 3 PID: 3675 at drivers/base/core.c:895 device_release+0x80/0x90
Modules linked in: btusb btrtl btintel btbcm bluetooth ...
CPU: 3 PID: 3675 Comm: rmmod Not tainted 4.20.0-rc4 #76
Hardware name: Google Kevin (DT)
pstate: 40000005 (nZcv daif -PAN -UAO)
pc : device_release+0x80/0x90
lr : device_release+0x80/0x90
sp : ffff00000c47bc70
x29: ffff00000c47bc70 x28: ffff8000e86b0d40
x27: 0000000000000000 x26: 0000000000000000
x25: 0000000056000000 x24: 0000000000000015
x23: ffff8000f0bbf860 x22: ffff000000d320a0
x21: ffff8000ee93e100 x20: ffff8000ed931428
x19: ffff8000ed931418 x18: 0000000000000020
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000400 x14: 0000000000000143
x13: 0000000000000000 x12: 0000000000000400
x11: 0000000000000157 x10: 0000000000000960
x9 : ffff00000c47b9b0 x8 : ffff8000e86b1700
x7 : 0000000000000000 x6 : ffff8000f7d520b8
x5 : ffff8000f7d520b8 x4 : 0000000000000000
x3 : ffff8000f7d58e68 x2 : ffff8000e86b0d40
x1 : 37d859939c964800 x0 : 0000000000000000
Call trace:
device_release+0x80/0x90
kobject_put+0x74/0xe8
device_unregister+0x20/0x30
ec_device_remove+0x34/0x48 [cros_ec_dev]
platform_drv_remove+0x28/0x48
device_release_driver_internal+0x1a8/0x240
driver_detach+0x40/0x80
bus_remove_driver+0x54/0xa8
driver_unregister+0x2c/0x58
platform_driver_unregister+0x10/0x18
cros_ec_dev_exit+0x1c/0x2d8 [cros_ec_dev]
__arm64_sys_delete_module+0x16c/0x1f8
el0_svc_common+0x84/0xd8
el0_svc_handler+0x2c/0x80
el0_svc+0x8/0xc
---[ end trace a57c4625f3c60ae8 ]---
Cc: stable@vger.kernel.org
Fixes: 3aa2177e4787 ("mfd: cros_ec: Use devm_kzalloc for private data")
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Some lower volume SanDisk Ultra Flair in 16GB, which the VID:PID is
in 0781:5591, will aggressively request LPM of U1/U2 during runtime,
when using this thumb drive as the OS installation key we found the
device will generate failure during U1 exit path making it dropped
from the USB bus, this causes a corrupted installation in system at
the end.
i.e.,
[ 166.918296] hub 2-0:1.0: state 7 ports 7 chg 0000 evt 0004
[ 166.918327] usb usb2-port2: link state change
[ 166.918337] usb usb2-port2: do warm reset
[ 166.970039] usb usb2-port2: not warm reset yet, waiting 50ms
[ 167.022040] usb usb2-port2: not warm reset yet, waiting 200ms
[ 167.276043] usb usb2-port2: status 02c0, change 0041, 5.0 Gb/s
[ 167.276050] usb 2-2: USB disconnect, device number 2
[ 167.276058] usb 2-2: unregistering device
[ 167.276060] usb 2-2: unregistering interface 2-2:1.0
[ 167.276170] xhci_hcd 0000:00:15.0: shutdown urb ffffa3c7cc695cc0 ep1in-bulk
[ 167.284055] sd 0:0:0:0: [sda] tag#0 FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
[ 167.284064] sd 0:0:0:0: [sda] tag#0 CDB: Read(10) 28 00 00 33 04 90 00 01 00 00
...
Analyzed the USB trace in the link layer we realized it is because
of the 6-ms timer of tRecoveryConfigurationTimeout which documented
on the USB 3.2 Revision 1.0, the section 7.5.10.4.2 of "Exit from
Recovery.Configuration"; device initiates U1 exit -> Recovery.Active
-> Recovery.Configuration, then the host timer timeout makes the link
transits to eSS.Inactive -> Rx.Detect follows by a Warm Reset.
Interestingly, the other higher volume of SanDisk Ultra Flair sharing
the same VID:PID, such as 64GB, would not request LPM during runtime,
it sticks at U0 always, thus disabling LPM does not affect those thumb
drives at all.
The same odd occures in SanDisk Ultra Fit 16GB, VID:PID in 0781:5583.
Signed-off-by: Harry Pan <harry.pan@intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Syzbot and KASAN found the following invalid-free bug in
port_over_current_notify():
--------------------------------------------------------------------------
BUG: KASAN: double-free or invalid-free in port_over_current_notify
drivers/usb/core/hub.c:5192 [inline]
BUG: KASAN: double-free or invalid-free in port_event
drivers/usb/core/hub.c:5241 [inline]
BUG: KASAN: double-free or invalid-free in hub_event+0xd97/0x4140
drivers/usb/core/hub.c:5384
CPU: 1 PID: 32710 Comm: kworker/1:3 Not tainted 4.20.0-rc3+ #129
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x244/0x39d lib/dump_stack.c:113
print_address_description.cold.7+0x9/0x1ff mm/kasan/report.c:256
kasan_report_invalid_free+0x64/0xa0 mm/kasan/report.c:336
__kasan_slab_free+0x13a/0x150 mm/kasan/kasan.c:501
kasan_slab_free+0xe/0x10 mm/kasan/kasan.c:528
__cache_free mm/slab.c:3498 [inline]
kfree+0xcf/0x230 mm/slab.c:3817
port_over_current_notify drivers/usb/core/hub.c:5192 [inline]
port_event drivers/usb/core/hub.c:5241 [inline]
hub_event+0xd97/0x4140 drivers/usb/core/hub.c:5384
process_one_work+0xc90/0x1c40 kernel/workqueue.c:2153
worker_thread+0x17f/0x1390 kernel/workqueue.c:2296
kthread+0x35a/0x440 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:352
--------------------------------------------------------------------------
The problem is caused by use of a static array to store
environment-string pointers. When the routine is called by multiple
threads concurrently, the pointers from one thread can overwrite those
from another.
The solution is to use an ordinary automatic array instead of a static
array.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: syzbot+98881958e1410ec7e53c@syzkaller.appspotmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add another Apple Cinema Display to the list of supported displays.
Signed-off-by: Alexander Theissen <alex.theissen@me.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
pstapriv->max_num_sta is always <= NUM_STA, since max_num_sta is either
set in _rtw_init_sta_priv() or rtw_set_beacon().
Fixes: ef9209b642f1 ("staging: rtl8723bs: Fix indenting errors and an off-by-one mistake in core/rtw_mlme_ext.c")
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit 8b7a13c3f404 ("staging: r8712u: Fix possible buffer
overrun") we fix a potential off by one by making the limit smaller.
The better fix is to make the buffer larger. This makes it match up
with the similar code in other drivers.
Fixes: 8b7a13c3f404 ("staging: r8712u: Fix possible buffer overrun")
Signed-off-by: Young Xiao <YangX92@hotmail.com>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver defines three states for a cppi channel.
- idle: .chan_busy == 0 && not in .pending list
- pending: .chan_busy == 0 && in .pending list
- busy: .chan_busy == 1 && not in .pending list
There are cases in which the cppi channel could be in the pending state
when cppi41_dma_issue_pending() is called after cppi41_runtime_suspend()
is called.
cppi41_stop_chan() has a bug for these cases to set channels to idle state.
It only checks the .chan_busy flag, but not the .pending list, then later
when cppi41_runtime_resume() is called the channels in .pending list will
be transitioned to busy state.
Removing channels from the .pending list solves the problem.
Fixes: 975faaeb9985 ("dma: cppi41: start tear down only if channel is busy")
Cc: stable@vger.kernel.org # v3.15+
Signed-off-by: Bin Liu <b-liu@ti.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
DMA buffer descriptors aren't allocated from atomic context, so they
can use the less heavyweigth GFP_NOWAIT.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The dmaengine documentation states that device_terminate_all may be
asynchronous and need not wait for the active transfers to stop.
This allows us to move most of the functionality currently implemented
in the sdma channel termination function to run in a worker, outside
of any atomic context. Moving this out of atomic context has two
benefits: we can now sleep while waiting for the channel to terminate,
instead of busy waiting and the freeing of the dma descriptors happens
with IRQs enabled, getting rid of a warning in the dma mapping code.
As the termination is now async, we need to implement the
device_synchronize dma engine function which simply waits for the
worker to finish its execution.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This reverts commit fe5b85c656bc. The SDMA engine needs the descriptors to
be contiguous in memory. As the dma pool API is only able to provide a
single descriptor per alloc invocation there is no guarantee that multiple
descriptors satisfy this requirement. Also the code in question is broken
as it only allocates memory for a single descriptor, without looking at the
number of descriptors required for the transfer, leading to out-of-bounds
accesses when the descriptors are written.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This reverts commit c1199875d327, as this depends on another commit
that is going to be reverted.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Cc: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
When the armada thermal module is inserted, removed and then reinserted,
the system panics as per the messages below. The reason is that "edit"
a live resource in the resource tree twice, and end up with it pointing
to some other hardware.
Editing live resources (resources that are part of the registered
resource tree) is not permissible - the resource tree is an ordered
set of resources, sorted by start address, and when a new resource is
inserted, it is validated that it (a) fits within its parent resource
and (b) does not overlap a neighbouring resource.
Get rid of this resource editing. We can instead adjust the return
value from ioremap() as ioremap() deals with the creation of page-
based mappings - provided the adjustment does not cross a page
boundary.
SError Interrupt on CPU1, code 0xbf000000 -- SError
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
pstate: 20400085 (nzCv daIf +PAN -UAO)
pc : regmap_mmio_read+0x3c/0x60
lr : regmap_mmio_read+0x3c/0x60
sp : ffffff800d453900
x29: ffffff800d453900 x28: ffffff800096a1d0
x27: 0000000000000100 x26: ffffff80009696d8
x25: ffffff8000969000 x24: ffffffc13a588918
x23: ffffffc13a9a28a8 x22: ffffff800d4539dc
x21: 0000000000000084 x20: ffffff800d4539dc
x19: ffffffc13a5d5480 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000
x15: 0000000000000000 x14: 0000000000000000
x13: 0000000000000000 x12: 0000000000000030
x11: 0101010101010101 x10: 7f7f7f7f7f7f7f7f
x9 : 0000000000000000 x8 : ffffffc13a5d5a80
x7 : 0000000000000000 x6 : 000000000000003f
x5 : 0000000000000000 x4 : 0000000000000000
x3 : ffffff800851be70 x2 : ffffff800851bd60
x1 : ffffff800d492ff8 x0 : 0000000000000000
Kernel panic - not syncing: Asynchronous SError Interrupt
CPU: 1 PID: 2749 Comm: modprobe Not tainted 4.19.0+ #175
Hardware name: Marvell 8040 MACCHIATOBin Double shot (DT)
Call trace:
dump_backtrace+0x0/0x158
show_stack+0x14/0x1c
dump_stack+0x90/0xb0
panic+0x128/0x298
print_tainted+0x0/0xa8
arm64_serror_panic+0x74/0x80
do_serror+0x5c/0xb8
el1_error+0xb4/0x144
regmap_mmio_read+0x3c/0x60
_regmap_bus_reg_read+0x18/0x20
_regmap_read+0x64/0x180
regmap_read+0x44/0x6c
armada_ap806_init+0x24/0x5c [armada_thermal]
armada_thermal_probe+0x2c8/0x37c [armada_thermal]
platform_drv_probe+0x4c/0xb0
really_probe+0x21c/0x2b4
driver_probe_device+0x58/0xfc
__driver_attach+0xd4/0xd8
bus_for_each_dev+0x50/0xa0
driver_attach+0x20/0x28
bus_add_driver+0x1c4/0x228
driver_register+0x6c/0x124
__platform_driver_register+0x4c/0x54
armada_thermal_driver_init+0x20/0x1000 [armada_thermal]
do_one_initcall+0x30/0x204
do_init_module+0x5c/0x1d4
load_module+0x1a88/0x212c
__se_sys_finit_module+0xa0/0xac
__arm64_sys_finit_module+0x1c/0x24
el0_svc_common+0x94/0xf0
el0_svc_handler+0x24/0x80
el0_svc+0x8/0x3c0
SMP: stopping secondary CPUs
Kernel Offset: disabled
CPU features: 0x0,21806000
Memory Limit: none
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Tested-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.
Catch the uninitialized PHY mode case, and allow 10G rates.
Fixes: d97c9f4ab000b ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 8c0e64ac4075 ("thermal: armada: get rid of the ->is_valid()
pointer") removed the unnecessary indirection through a function
pointer, but in doing so, also removed the negation operator too:
- if (priv->data->is_valid && !priv->data->is_valid(priv)) {
+ if (armada_is_valid(priv)) {
which results in:
armada_thermal f06f808c.thermal: Temperature sensor reading not valid
armada_thermal f2400078.thermal: Temperature sensor reading not valid
armada_thermal f4400078.thermal: Temperature sensor reading not valid
at boot, or whenever the "temp" sysfs file is read. Replace the
negation operator.
Fixes: 8c0e64ac4075 ("thermal: armada: get rid of the ->is_valid() pointer")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.
This patch removes the unwarranted call to of_node_put().
Fixes: 414fd46e7762 ("fsl/fman: Add FMan support")
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
Nir Dotan
Ido Schimmel
Stefan Hajnoczi
Halil Pasic
Andy Shevchenko
Greg Kroah-Hartman
Johan Hovold
Macpaul Lin
Mathias Nyman
Sandeep Singh
Sam Bobroff
Dave Airlie
Linus Torvalds
Dan Williams
Mathias Payer
David S. Miller
James Zhu
Lijun Ou
Julia Lawall
Peter Shih
Enric Balletbo i Serra
Harry Pan
Alan Stern
Alexander Theissen
Young Xiao
Bin Liu
Lucas Stach
Stefan Wahren
Russell King
Baruch Siach
Nicolas Saenz Julienne