| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* 'hwmon-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/staging: (24 commits)
hwmon: (lm90) Refactor reading of config2 register
hwmon: (lm90) Make SA56004 detection more robust
hwmon: (lm90) Simplify handling of extended local temp register
hwmon: (pmbus) Add client driver for LM25066, LM5064, and LM5066
hwmon: (max34440) Add support for peak attributes
hwmon: (max8688) Add support for peak attributes
hwmon: (max16064) Add support for peak attributes
hwmon: (adm1275) Add support for peak attributes
hwmon: (pmbus) Add support for peak attributes
hwmon: Add new attributes to sysfs ABI
hwmon: (pmbus) Strengthen check for status register existence
hwmon: (pmbus) Add support for virtual pages
hwmon: (pmbus) Support reading and writing of word registers in device specific code
hwmon: (pmbus) Increase attribute name size
hwmon: (pmbus) Add ADP4000, NCP4200 and NCP4208 to list of supported devices
hwmon: (pmbus) Add support for VID output voltage mode
hwmon: (pmbus) Move PMBus drivers to drivers/hwmon/pmbus
hwmon: (coretemp) Add core/pkg threshold support to Coretemp
hwmon: (lm95241) Add support for LM95231
hwmon: LM95245 driver
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (71 commits)
[SCSI] fcoe: cleanup cpu selection for incoming requests
[SCSI] fcoe: add fip retry to avoid missing critical keep alive
[SCSI] libfc: fix warn on in lport retry
[SCSI] libfc: Remove the reference to FCP packet from scsi_cmnd in case of error
[SCSI] libfc: cleanup sending SRR request
[SCSI] libfc: two minor changes in comments
[SCSI] libfc, fcoe: ignore rx frame with wrong xid info
[SCSI] libfc: release exchg cache
[SCSI] libfc: use FC_MAX_ERROR_CNT
[SCSI] fcoe: remove unused ptype field in fcoe_rcv_info
[SCSI] bnx2fc: Update copyright and bump version to 1.0.4
[SCSI] bnx2fc: Tx BDs cache in write tasks
[SCSI] bnx2fc: Do not arm CQ when there are no CQEs
[SCSI] bnx2fc: hold tgt lock when calling cmd_release
[SCSI] bnx2fc: Enable support for sequence level error recovery
[SCSI] bnx2fc: HSI changes for tape
[SCSI] bnx2fc: Handle REC_TOV error code from firmware
[SCSI] bnx2fc: REC/SRR link service request and response handling
[SCSI] bnx2fc: Support 'sequence cleanup' task
[SCSI] dh_rdac: Associate HBA and storage in rdac_controller to support partitions in storage
...
|
|
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (430 commits)
[media] ir-mce_kbd-decoder: include module.h for its facilities
[media] ov5642: include module.h for its facilities
[media] em28xx: Fix DVB-C maxsize for em2884
[media] tda18271c2dd: Fix saw filter configuration for DVB-C @6MHz
[media] v4l: mt9v032: Fix Bayer pattern
[media] V4L: mt9m111: rewrite set_pixfmt
[media] V4L: mt9m111: fix missing return value check mt9m111_reg_clear
[media] V4L: initial driver for ov5642 CMOS sensor
[media] V4L: sh_mobile_ceu_camera: fix Oops when USERPTR mapping fails
[media] V4L: soc-camera: remove soc-camera bus and devices on it
[media] V4L: soc-camera: un-export the soc-camera bus
[media] V4L: sh_mobile_csi2: switch away from using the soc-camera bus notifier
[media] V4L: add media bus configuration subdev operations
[media] V4L: soc-camera: group struct field initialisations together
[media] V4L: soc-camera: remove now unused soc-camera specific PM hooks
[media] V4L: pxa-camera: switch to using standard PM hooks
[media] NetUP Dual DVB-T/C CI RF: force card hardware revision by module param
[media] Don't OOPS if videobuf_dvb_get_frontend return NULL
[media] NetUP Dual DVB-T/C CI RF: load firmware according card revision
[media] omap3isp: Support configurable HS/VS polarities
...
Fix up conflicts:
- arch/arm/mach-omap2/board-rx51-peripherals.c:
cleanup regulator supply definitions in mach-omap2
vs
OMAP3: RX-51: define vdds_csib regulator supply
- drivers/staging/tm6000/tm6000-alsa.c (trivial)
|
|
* 'stable/bug.fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/konrad/xen:
xen/balloon: Fix compile errors - missing header files.
xen/grant: Fix compile warning.
xen/pciback: remove duplicated #include
|
|
Fixes this:
drivers/char/ramoops.c: In function 'ramoops_init':
drivers/char/ramoops.c:221: error: implicit declaration of function 'IS_ERR'
drivers/char/ramoops.c:222: error: implicit declaration of function 'PTR_ERR'
If it actually builds on other platforms, it's probably getting
linux/err.h via some other #include.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: remove printks about disabled bridge windows
PCI: fold pci_calc_resource_flags() into decode_bar()
PCI: treat mem BAR type "11" (reserved) as 32-bit, not 64-bit, BAR
PCI: correct pcie_set_readrq write size
PCI: pciehp: change wait time for valid configuration access
x86/PCI: Preserve existing pci=bfsort whitelist for Dell systems
PCI: ARI is a PCIe v2 feature
x86/PCI: quirks: Use pci_dev->revision
PCI: Make the struct pci_dev * argument of pci_fixup_irqs const.
PCI hotplug: cpqphp: use pci_dev->vendor
PCI hotplug: cpqphp: use pci_dev->subsystem_{vendor|device}
x86/PCI: config space accessor functions should not ignore the segment argument
PCI: Assign values to 'pci_obff_signal_type' enumeration constants
x86/PCI: reduce severity of host bridge window conflict warnings
PCI: enumerate the PCI device only removed out PCI hieratchy of OS when re-scanning PCI
PCI: PCIe AER: add aer_recover_queue
x86/PCI: select direct access mode for mmconfig option
PCI hotplug: Rename is_ejectable which also exists in dock.c
|
|
* 'next/dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/linux-arm-soc: (21 commits)
arm/dt: tegra devicetree support
arm/versatile: Add device tree support
dt/irq: add irq_domain_generate_simple() helper
irq: add irq_domain translation infrastructure
dmaengine: imx-sdma: add device tree probe support
dmaengine: imx-sdma: sdma_get_firmware does not need to copy fw_name
dmaengine: imx-sdma: use platform_device_id to identify sdma version
mmc: sdhci-esdhc-imx: add device tree probe support
mmc: sdhci-pltfm: dt device does not pass parent to sdhci_alloc_host
mmc: sdhci-esdhc-imx: get rid of the uses of cpu_is_mx()
mmc: sdhci-esdhc-imx: do not reference platform data after probe
mmc: sdhci-esdhc-imx: extend card_detect and write_protect support for mx5
net/fec: add device tree probe support
net: ibm_newemac: convert it to use of_get_phy_mode
dt/net: add helper function of_get_phy_mode
net/fec: gasket needs to be enabled for some i.mx
serial/imx: add device tree probe support
serial/imx: get rid of the uses of cpu_is_mx1()
arm/dt: Add dtb make rule
arm/dt: Add skeleton dtsi file
...
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-watchdog: (25 commits)
watchdog: WatchDog Timer Driver Core - Add minimum and max timeout
watchdog: WatchDog Timer Driver Core - Add ioctl call
watchdog: WatchDog Timer Driver Core - Add nowayout feature
watchdog: WatchDog Timer Driver Core - Add Magic Close feature
watchdog: WatchDog Timer Driver Core - Add WDIOC_SETTIMEOUT and WDIOC_GETTIMEOUT ioctl
watchdog: WatchDog Timer Driver Core - Add WDIOC_SETOPTIONS ioctl
watchdog: WatchDog Timer Driver Core - Add WDIOC_KEEPALIVE ioctl
watchdog: WatchDog Timer Driver Core - Add basic ioctl functionality
watchdog: WatchDog Timer Driver Core - Add basic framework
watchdog: hpwdt: add next gen HP servers
watchdog: it8712f_wdt.c: improve includes
watchdog: at91sam9/wdt: move register header to drivers
watchdog: Add Xilinx watchdog timer driver
watchdog: remove empty pm-functions
watchdog: sp805: Flush posted writes in enable/disable.
watchdog: sp805: Don't write 0 to the load value register.
watchdog: imx2_wdt: add device tree probe support
watchdog: s3c2410: Add support for device tree based probe
watchdog: mpcore_wdt: Add suspend/resume support.
watchdog: mtx1-wdt: use dev_{err,info} instead of printk()
...
|
|
On a recent compile, I got this warning:
CC [M] drivers/net/pcmcia/smc91c92_cs.o
drivers/net/pcmcia/smc91c92_cs.c: In function ‘smc91c92_probe’:
drivers/net/pcmcia/smc91c92_cs.c:812:12: warning: ‘j’ may be used uninitialized in this function
However, "j" is only used in a branch which has the same condition as
a previous branch, where j is set, e.g.
int j;
if (CONDITION)
j = VALUE
...
if (CONDITION)
printk(j)
Still, avoid this warning, as it is easy to circumvent.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Without CONFIG_HERMES_PRISM, only match cards that have "Version 01.01"
as the third product ID. Those have Agere firmware.
With CONFIG_HERMES_PRISM, match all 0x0156:0x0002 cards.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Cards with numeric ID 0x0156:0x0002 and third ID "Version 01.02" can be
assumed to have Intersil firmware. Cards with Agere firmware use
"Version 01.01".
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Kill off the buff gpio as not used anywhere.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
Now the are optional, let us get rid of the ones that don't have
any content.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
10 boards define these empty, probably indicating not everyone has a use for them.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
|
|
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:446:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/rc/ir-mce_kbd-decoder.c:446:16: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:447:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/rc/ir-mce_kbd-decoder.c:447:15: warning: function declaration isn't a prototype
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: error: expected declaration specifiers or '...' before string constant
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: data definition has no type or storage class
drivers/media/rc/ir-mce_kbd-decoder.c:448:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/rc/ir-mce_kbd-decoder.c:448:20: warning: function declaration isn't a prototype
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/video/ov5642.c:985:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:985:1: warning: type defaults to 'int' in declaration of 'MODULE_DEVICE_TABLE'
drivers/media/video/ov5642.c:985:1: warning: parameter names (without types) in function declaration
drivers/media/video/ov5642.c: In function 'ov5642_mod_init':
drivers/media/video/ov5642.c:998:9: error: 'THIS_MODULE' undeclared (first use in this function)
drivers/media/video/ov5642.c:998:9: note: each undeclared identifier is reported only once for each function it appears in
drivers/media/video/ov5642.c: At top level:
drivers/media/video/ov5642.c:1009:20: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1009:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1009:1: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
drivers/media/video/ov5642.c:1009:20: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c:1010:15: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1010:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1010:1: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
drivers/media/video/ov5642.c:1010:15: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c:1011:16: error: expected declaration specifiers or '...' before string constant
drivers/media/video/ov5642.c:1011:1: warning: data definition has no type or storage class
drivers/media/video/ov5642.c:1011:1: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
drivers/media/video/ov5642.c:1011:16: warning: function declaration isn't a prototype
drivers/media/video/ov5642.c: In function 'ov5642_mod_init':
drivers/media/video/ov5642.c:999:1: warning: control reaches end of non-void function
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Only Sparc and PPC actually have the asm/prom.h include and as such they
can't be moved outside of the ifdefs.
Reported-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Several vendors implement a second configuration register, which we
check during device detection. Refactor the code to avoid duplication.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
With a device ID register value of 0, the SA56004 detection is rather
weak. Check several other register too to confirm the detection, as we
do for other supported devices.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Stijn Devriendt <sdevrien@cisco.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
The optional extended local temperature register can never have
address 0, as this address is already used by another register. Thus
we can get rid of flag LM90_HAVE_LOCAL_EXT and simply rely on
reg_local_ext being non-zero to determine if a given chip has this
extension or not. This makes the code more simple.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Stijn Devriendt <sdevrien@cisco.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
PMBus client driver supporting National Semiconductor LM25066, LM5064, and LM5066.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
proc_fork_connector() uses ->real_parent lockless. This is not safe if
copy_process() was called with CLONE_THREAD or CLONE_PARENT, in this case
the parent != current can go away at any moment.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Cc: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The D-Link DGE-530T rev C1 is a re-badged Realtek 8169 named DLG10028C,
unlike the previous revisions which were skge based. It is probably
the same as the discontinued DGE-528T (0x4300) other than the PCI ID.
The PCI ID is 0x1186:0x4302.
Adding it to r8169.c where 0x1186:0x4300 is already found makes the card
be detected and work.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=38862
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=34552
Signed-off-by: Klement Fish <klement2@azet.sk>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Most PMBus devices provide manufacturer specific commands to read low and/or
high peak values for some or all of its sensors.
To support providing those values as lowest/highest attributes to the user,
introduce virtual PMBus commands. Those commands reside outside the normal
command set and have to be implemented in device specific code, which map the
virtual commands to device specific commands.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
With virtual register page support, it is now possible that the status register
on virtual pages does not exist or is itself virtual. To take this into account
when creating alarm attributes, generate those attributes only if the status
register on the respective page is known to exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Some PMBus chips have non-standard sensor registers. An easy way to
support such sensors is to introduce virtual pages and map the non-standard
registers into standard registers on an extra page.
For this to work, the code verifying if the configured number of pages exists
has to be removed. Since a wrong number of pages can only be configured in a
front-end driver, this should not have a practical impact since the resulting
errors should be found during development and testing.
Also, functions to read the chip status while checking if a command register
exists must be modified to no longer set the page register before reading the
status, since the physical page associated with the checked register may not
exist. This does not make a functional difference since the page was already set
when the attempt to read the register was made.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Some PMBus devices use non-standard registers for some of the sensors and/or
limits. To support such devices, add code to support reading and writing of word
size registers in device specific code.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.
This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
The logic at em28xx_isoc_dvb_max_packetsize() sucks, at least for newer
the needed packet size. Yet, it is better than nothing.
Rewrite the code in order to change the default to 752 for em2884 and
newer chips and provide a better way to handle per-chipset specifics.
For em2874, the current default should be enough, as the only em2874
board is currently a 1-seg ISDB-T board, so, it needs only a limited
amount of bandwidth.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Currently, the driver assumes that all QAM carriers are spaced with
8MHz. This is wrong, and may decrease QoS on Countries like Brazil,
that have DVB-C carriers with 6MHz-spaced.
Fortunately, both ITU-T J-83 and EN 300 429 specifies a way to
associate the symbol rate with the bandwidth needed for it.
For ITU-T J-83 2007 annex A, the maximum symbol rate for 6 MHz is:
6 MHz / 1.15 = 5217391 Bauds
For ITU-T J-83 2007 annex C, the maximum symbol rate for 6 MHz is:
6 MHz / 1.13 = 5309735 Bauds.
As this tuner is currently used only for DRX-K, and it is currently
hard-coded to annex A, I've opted to use the roll-off factor of 0.15,
instead of 0.13.
If we ever support annex C, the better would be to add a DVB S2API
call to allow changing between Annex A and C, and add the 0.13 roll-off
factor to it.
This code is currently being used on other frontends, so I think we
should later add a core function with this code, to warrant that
it will be properly implemented everywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
n2_crypto: Attach on Niagara-T3.
n2rng: Attach on Niagara-T3.
sparc: Detect and handle UltraSPARC-T3 cpu types.
sparc: Don't do expensive hypervisor PCR write unless necessary.
sparc: Add T3 sun4v cpu type and hypervisor group defines.
sparc: Don't leave sparc_pmu_type NULL on sun4v.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e
gro: Only reset frag0 when skb can be pulled
...
|
|
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
|
|
A small modification was necessary since in the machine description
for 'n2cp' and 'ncp' nodes, there no longer is an 'intr' property.
That's OK because this property was always nothing more than an
array of integers '1' ... 'nr_inos + 1' so we can just compute it
in-place.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
And stop referring to Victoria Falls, as the attribute we're
talking about is whether the rng is multi-unit capable which
applies to several chip variants now.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cleanup to:
- have selection for all types of frames, not just FCP.
- remove redundant cpu_online check once fcoe_select_cpu called
as this is not required since later code flow check for offlined
cpu.
- Simplify fcoe_select_cpu() by removing unnecessary checks to
skip curr_cpu, this also fixes possibly infinite loop in case
of curr_cpu is the only cpu while iterating in the loop.
This cleanup mainly applies to target as incoming request are
mostly for target, therefore Kiran has verified the patch
with target also.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Kiran Patil <kiran.patil@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Use pending queue to retry FIP frame in case its tx
fails and use common pending queue for both fcoe
and fip frames using fcoe_port_send.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The lport retry timer hits warn on in case
it has become ready in response from fip
login from fcoe_ctlr_flogi_send(), this is
possible but safe code path, therefore
removing this warn on.
Jun 22 03:16:30 10.0.16.6 [488198.316517] host3: Assigned Port ID 180f02
Jun 22 03:16:32 10.0.16.6 [488200.091561] ------------[ cut here ]------------
Jun 22 03:16:32 10.0.16.6 [488200.091586] WARNING: at
drivers/scsi/libfc/fc_lport.c:1355 fc_lport_timeout+0xd9/0xe0 [libfc]()
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
fc_queuecommand() allocates an FCP packet for each SCSI command and sends
it out on the wire. In the process it stores the reference to the FCP packet
in the scsi_cmnd structure.
Now, in case under stress testing the libfc exchange layer runs out of
exchanges the fc_queuecommand() may not be able to send out commands out on
the wire. In such a scenario if there is an error in sending the FCP packet
out the wire; fc_queuecommand() deletes the FCP packet from internal queue,
releases the FCP packet and returns a SCSI_MLQUEUE_HOST_BUSY status to the
scsi-ml. But, the reference to the FCP packet set in the scsi_cmnd is not
removed from the scsi_cmnd in this code path.
This might lead to a crash under stress testing where the scsi_cmnd failed by
fc_queuecommand() comes up to fc_eh_abort() via scsi eh thread. fc_eh_abort()
will get reference to the FCP packet to be aborted from the scsi_cmnd for
further FCP abort related processing and then try to release the FCP packet
that has already been released.
This patch removes the FCP packet reference from the scsi_cmnd before returning
back from fc_queuecommand() in case of an error in sending out the FCP packet.
Signed-off-by: Neerav Parikh <Neerav.Parikh@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The variable on stack, namely cdb_op, is not used but removed.
[ Patch reworked by Robert Love due to invalid patch format ]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
One change is to cleanup typo in comment for fc_fcp_recv(), another corrects
the misleading comment for fc_fcp_abts_resp().
[ Patch reworked by Robert Love due to invalid patch format ]
Signed-off-by: Hillf Danton <dhillf@gmail.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
Drop the rx frame having xid with wrong cpu info
or received with xid not matching to our xid.
Not dropping such frame is causing panic as
that causes accessing data struct beyond their
bounds.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
Linus Torvalds
James Bottomley
Dominik Brodowski
Pavel Roskin
Jonathan Cameron
Stephen Rothwell
Jiri Kosina
Jean Delvare
Guenter Roeck
Oleg Nesterov
Lennart Sorensen
Klement Fish
Mauro Carvalho Chehab
David S. Miller
Vasu Dev
Neerav Parikh
Hillf Danton