aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2019-09-10scsi: hisi_sas: Assign NCQ tag for all NCQ commandsXiang Chen4-18/+8
Currently the NCQ tag is only assigned for FPDMA READ and FPDMA WRITE commands, and for other NCQ commands (such as FPDMA SEND), their NCQ tags are set in the delivery command to 0. So for all the NCQ commands, we also need to assign normal NCQ tag for them, so drop the command type check in hisi_sas_get_ncq_tag() [drop hisi_sas_get_ncq_tag() altogether actually], and always use the ATA command NCQ tag when appropriate. Link: https://lore.kernel.org/r/1567774537-20003-8-git-send-email-john.garry@huawei.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: hisi_sas: Update all the registers after suspend and resumeXiang Chen1-2/+8
After suspend and resume, the HW registers will be set back to their initial value. We use init_reg_v3_hw() to set some registers, but some registers are set via firmware in ACPI "_RST" method, so add reset handler before init_reg_v3_hw(). Link: https://lore.kernel.org/r/1567774537-20003-7-git-send-email-john.garry@huawei.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: hisi_sas: Retry 3 times TMF IO for SAS disks when init deviceXiang Chen1-6/+10
When init device for SAS disks, it will send TMF IO to clear disks. At that time TMF IO is broken by some operations such as injecting controller reset from HW RAs event, the TMF IO will be timeout, and at last device will be gone. Print is as followed: hisi_sas_v3_hw 0000:74:02.0: dev[240:1] found ... hisi_sas_v3_hw 0000:74:02.0: controller resetting... hisi_sas_v3_hw 0000:74:02.0: phyup: phy7 link_rate=10(sata) hisi_sas_v3_hw 0000:74:02.0: phyup: phy0 link_rate=9(sata) hisi_sas_v3_hw 0000:74:02.0: phyup: phy1 link_rate=9(sata) hisi_sas_v3_hw 0000:74:02.0: phyup: phy2 link_rate=9(sata) hisi_sas_v3_hw 0000:74:02.0: phyup: phy3 link_rate=9(sata) hisi_sas_v3_hw 0000:74:02.0: phyup: phy6 link_rate=10(sata) hisi_sas_v3_hw 0000:74:02.0: phyup: phy5 link_rate=11 hisi_sas_v3_hw 0000:74:02.0: phyup: phy4 link_rate=11 hisi_sas_v3_hw 0000:74:02.0: controller reset complete hisi_sas_v3_hw 0000:74:02.0: abort tmf: TMF task timeout and not done hisi_sas_v3_hw 0000:74:02.0: dev[240:1] is gone sas: driver on host 0000:74:02.0 cannot handle device 5000c500a75a860d, error:5 To improve the reliability, retry TMF IO max of 3 times for SAS disks which is the same as softreset does. Link: https://lore.kernel.org/r/1567774537-20003-6-git-send-email-john.garry@huawei.com Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: hisi_sas: Remove sleep after issue phy reset if sas_smp_phy_control() failsLuo Jiaxing1-2/+3
At expander environment, we delay after issue phy reset to wait for hardware to handle phy reset. But if sas_smp_phy_control() fails, the delay is unnecessary so remove it. Link: https://lore.kernel.org/r/1567774537-20003-5-git-send-email-john.garry@huawei.com Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: hisi_sas: Directly return when running I_T_nexus reset if phy disabledLuo Jiaxing1-0/+5
At hisi_sas_debug_I_T_nexus_reset(), we call sas_phy_reset() to reset a phy. But if the phy is disabled, sas_phy_reset() will directly return -ENODEV without issue a phy reset request. If so, We can directly return -ENODEV to libsas before issue a phy reset. Link: https://lore.kernel.org/r/1567774537-20003-4-git-send-email-john.garry@huawei.com Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: hisi_sas: Use true/false as input parameter of sas_phy_reset()Luo Jiaxing1-2/+2
When calling sas_phy_reset(), we need to specify whether the reset type is hard reset or link reset - use true/false for clarity. Link: https://lore.kernel.org/r/1567774537-20003-3-git-send-email-john.garry@huawei.com Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: hisi_sas: add debugfs auto-trigger for internal abort time outLuo Jiaxing1-0/+3
This trigger is add at _hisi_sas_internal_task_abort() Link: https://lore.kernel.org/r/1567774537-20003-2-git-send-email-john.garry@huawei.com Signed-off-by: Luo Jiaxing <luojiaxing@huawei.com> Signed-off-by: John Garry <john.garry@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: virtio_scsi: unplug LUNs when events missedMatt Lupfer1-0/+33
The event handler calls scsi_scan_host() when events are missed, which will hotplug new LUNs. However, this function won't remove any unplugged LUNs. The result is that hotunplug doesn't work properly when the number of unplugged LUNs exceeds the event queue size (currently 8). Scan existing LUNs when events are missed to check if they are still present. If not, remove them. Link: https://lore.kernel.org/r/20190905181903.29756-1-mlupfer@ddn.com Signed-off-by: Matt Lupfer <mlupfer@ddn.com> Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com> Acked-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: scsi_dh_rdac: zero cdb in send_mode_select()Martin Wilck1-0/+2
cdb in send_mode_select() is not zeroed and is only partially filled in rdac_failover_get(), which leads to some random data getting to the device. Users have reported storage responding to such commands with INVALID FIELD IN CDB. Code before commit 327825574132 was not affected, as it called blk_rq_set_block_pc(). Fix this by zeroing out the cdb first. Identified & fix proposed by HPE. Fixes: 327825574132 ("scsi_dh_rdac: switch to scsi_execute_req_flags()") Cc: stable@vger.kernel.org Link: https://lore.kernel.org/r/20190904155205.1666-1-martin.wilck@suse.com Signed-off-by: Martin Wilck <mwilck@suse.com> Acked-by: Ales Novak <alnovak@suse.cz> Reviewed-by: Shane Seymour <shane.seymour@hpe.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-10scsi: fcoe: fix null-ptr-deref Read in fc_release_transportzhengbin1-5/+11
In fcoe_if_init, if fc_attach_transport(&fcoe_vport_fc_functions) fails, need to free the previously memory and return fail, otherwise will trigger null-ptr-deref Read in fc_release_transport. fcoe_exit fcoe_if_exit fc_release_transport(fcoe_vport_scsi_transport) Link: https://lore.kernel.org/r/1566279789-58207-1-git-send-email-zhengbin13@huawei.com Reported-by: Hulk Robot <hulkci@huawei.com> Reviewed-by: Hannes Reinecke <hare@suse.com> Signed-off-by: zhengbin <zhengbin13@huawei.com> Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2019-09-11gpio: Initialize the irqchip valid_mask with a callbackLinus Walleij7-50/+101
After changing the valid_mask for the struct gpio_chip to detect the need and presence of a valid mask with the presence of a .init_valid_mask() callback to fill it in, we augment the gpio_irq_chip to use the same logic. Switch all driver using the gpio_irq_chio valid_mask over to this new method. This makes sure the valid_mask for the gpio_irq_chip gets filled in when we add the gpio_chip, which makes it a little easier to switch over drivers using the old way of setting up gpio_irq_chip over to the new method of passing the gpio_irq_chip along with the gpio_chip. (See drivers/gpio/TODO for details.) Cc: Joel Stanley <joel@jms.id.au> Cc: Thierry Reding <treding@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Tested-by: Hans de Goede <hdegoede@redhat.com> Reviewed-by: Andrew Jeffery <andrew@aj.id.au> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Patrice Chotard <patrice.chotard@st.com> Link: https://lore.kernel.org/r/20190904140104.32426-1-linus.walleij@linaro.org
2019-09-10misc: mic: Use PTR_ERR_OR_ZERO rather than its implementationzhong jiang1-3/+2
PTR_ERR_OR_ZERO contains if(IS_ERR(...)) + PTR_ERR. It is better to use it directly. hence just replace it. Signed-off-by: zhong jiang <zhongjiang@huawei.com> Link: https://lore.kernel.org/r/1567665795-5901-3-git-send-email-zhongjiang@huawei.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-10net/mlx5: FWTrace, Reduce stack usageSaeed Mahameed1-3/+4
Mark mlx5_tracer_print_trace as noinline as the function only uses 512 bytes on the stack to avoid the following build warning: drivers/net/ethernet/mellanox/mlx5/core/diag/fw_tracer.c:660:13: error: stack frame size of 1032 bytes in function 'mlx5_fw_tracer_handle_traces' [-Werror,-Wframe-larger-than=] Fixes: 70dd6fdb8987 ("net/mlx5: FW tracer, parse traces and kernel tracing support") Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-09-10net/mlx5: Fix addr's type in mlx5dr_icm_dmNathan Chancellor1-1/+1
clang errors when CONFIG_PHYS_ADDR_T_64BIT is not set: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_icm_pool.c:121:8: error: incompatible pointer types passing 'u64 *' (aka 'unsigned long long *') to parameter of type 'phys_addr_t *' (aka 'unsigned int *') [-Werror,-Wincompatible-pointer-types] &icm_mr->dm.addr, &icm_mr->dm.obj_id); ^~~~~~~~~~~~~~~~ include/linux/mlx5/driver.h:1092:39: note: passing argument to parameter 'addr' here u64 length, u16 uid, phys_addr_t *addr, u32 *obj_id); ^ 1 error generated. Use phys_addr_t for addr's type in mlx5dr_icm_dm, which won't change anything with 64-bit builds because phys_addr_t is u64 when CONFIG_PHYS_ADDR_T_64BIT is set, which is always when CONFIG_64BIT is set. Fixes: 29cf8febd185 ("net/mlx5: DR, ICM pool memory allocator") Link: https://github.com/ClangBuiltLinux/linux/issues/653 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-09-10net/mlx5: Fix rt's type in dr_action_create_reformat_actionNathan Chancellor1-1/+1
clang warns: drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c:1080:9: warning: implicit conversion from enumeration type 'enum mlx5_reformat_ctx_type' to different enumeration type 'enum mlx5dr_action_type' [-Wenum-conversion] rt = MLX5_REFORMAT_TYPE_L2_TO_L2_TUNNEL; ~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c:1082:9: warning: implicit conversion from enumeration type 'enum mlx5_reformat_ctx_type' to different enumeration type 'enum mlx5dr_action_type' [-Wenum-conversion] rt = MLX5_REFORMAT_TYPE_L2_TO_L3_TUNNEL; ~ ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ drivers/net/ethernet/mellanox/mlx5/core/steering/dr_action.c:1084:51: warning: implicit conversion from enumeration type 'enum mlx5dr_action_type' to different enumeration type 'enum mlx5_reformat_ctx_type' [-Wenum-conversion] ret = mlx5dr_cmd_create_reformat_ctx(dmn->mdev, rt, data_sz, data, ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ ^~ 3 warnings generated. Use the right type for rt, which is mlx5_reformat_ctx_type so there are no warnings about mismatched types. Fixes: 9db810ed2d37 ("net/mlx5: DR, Expose steering action functionality") Link: https://github.com/ClangBuiltLinux/linux/issues/652 Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Reported-by: Austin Kim <austindh.kim@gmail.com> Reported-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
2019-09-10hwmon: (shtc1) add support for the SHTC3 sensorDan Robertson2-16/+45
Add support for the Sensirion SHTC3 humidity and temperature sensor to the shtc1 module. Signed-off-by: Dan Robertson <dan@dlrobertson.com> Link: https://lore.kernel.org/r/20190905014554.21658-2-dan@dlrobertson.com Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-10hwmon: (shtc1) fix shtc1 and shtw1 id maskDan Robertson1-1/+1
Fix an error in the bitmaskfor the shtc1 and shtw1 bitmask used to retrieve the chip ID from the ID register. See section 5.7 of the shtw1 or shtc1 datasheet for details. Fixes: 1a539d372edd9832444e7a3daa710c444c014dc9 ("hwmon: add support for Sensirion SHTC1 sensor") Signed-off-by: Dan Robertson <dan@dlrobertson.com> Link: https://lore.kernel.org/r/20190905014554.21658-3-dan@dlrobertson.com [groeck: Reordered to be first in series and adjusted accordingly] Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-09-10kdoc: fix nfp_fw_load documentationDirk van der Merwe1-1/+1
Fixed the incorrect prefix for the 'nfp_fw_load' function. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10nfp: devlink: add 'reset_dev_on_drv_probe' supportDirk van der Merwe1-0/+29
Add support for the 'reset_dev_on_drv_probe' devlink parameter. The reset control policy is controlled by the 'abi_drv_reset' hwinfo key. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10nfp: devlink: add 'fw_load_policy' supportDirk van der Merwe1-0/+165
Add support for the 'fw_load_policy' devlink parameter. The FW load policy is controlled by the 'app_fw_from_flash' hwinfo key. Remap the values from devlink to the hwinfo key and back. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10nfp: add devlink param infrastructureDirk van der Merwe4-0/+71
Register devlink parameters for driver use. Subsequent patches will add support for specific parameters. In order to support devlink parameters, the management firmware needs to be able to lookup and set hwinfo keys. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10nfp: honor FW reset and loading policiesDirk van der Merwe3-25/+132
The firmware reset and loading policies can be controlled with the combination of three hwinfo keys, 'abi_drv_reset', 'abi_drv_load_ifc' and 'app_fw_from_flash'. 'app_fw_from_flash' defines which firmware should take precedence, 'Disk', 'Flash' or the 'Preferred' firmware. When 'Preferred' is selected, the management firmware makes the decision on which firmware will be loaded by comparing versions of the flash firmware and the host supplied firmware. 'abi_drv_reset' defines when the driver should reset the firmware when the driver is probed, either 'Disk' if firmware was found on disk, 'Always' reset or 'Never' reset. Note that the device is always reset on driver unload if firmware was loaded when the driver was probed. 'abi_drv_load_ifc' defines a list of PF devices allowed to load FW on the device. Furthermore, we limit the cases to where the driver will unload firmware again when the driver is removed to only when firmware was loaded by the driver and only if this particular device was the only one that could have loaded firmware. This is needed to avoid firmware being removed while in use on multi-host platforms. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10nfp: nsp: add support for hwinfo set operationDirk van der Merwe2-0/+21
Add support for the NSP HWinfo set command. This closely follows the HWinfo lookup command. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10nfp: nsp: add support for optional hwinfo lookupDirk van der Merwe2-4/+50
There are cases where we want to read a hwinfo entry from the NFP, and if it doesn't exist, use a default value instead. To support this, we must silence warning/error messages when the hwinfo entry doesn't exist since this is a valid use case. The NSP command structure provides the ability to silence command errors, in which case the caller should log any command errors appropriately. Protocol errors are unaffected by this. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10nfp: nsp: add support for fw_loaded commandDirk van der Merwe2-0/+16
Add support for the simple command that indicates whether application firmware is loaded. Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com> Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by: Simon Horman <simon.horman@netronome.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10net: dsa: mv88e6xxx: add RXNFC supportVivien Didelot2-0/+226
Implement the .get_rxnfc and .set_rxnfc DSA operations to configure a port's Layer 2 Policy Control List (PCL) via ethtool. Currently only dropping frames based on MAC Destination or Source Address (including the option VLAN parameter) is supported. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10net: dsa: mv88e6xxx: introduce .port_set_policyVivien Didelot4-1/+121
Introduce a new .port_set_policy operation to configure a port's Policy Control List, based on mapping such as DA, SA, Etype and so on. Models similar to 88E6352 and 88E6390 are supported at the moment. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10net: dsa: mv88e6xxx: complete ATU state definitionsVivien Didelot3-27/+41
Marvell has different values for the state of a MAC address, depending on its multicast bit. This patch completes the definitions for these states. At the same time, use 0 which is intuitive enough and simplifies the code a bit, instead of the UC or MC unused value. Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10ARM: 8906/1: drivers/amba: add reset control to amba bus probeDINH L NGUYEN1-0/+14
The primecell controller on some SoCs, i.e. SoCFPGA, is held in reset by default. Until recently, the DMA controller was brought out of reset by the bootloader(i.e. U-Boot). But a recent change in U-Boot, the peripherals that are not used are held in reset and are left to Linux to bring them out of reset. Add a mechanism for getting the reset property and de-assert the primecell module from reset if found. This is a not a hard fail if the reset property is not present in the device tree node, so the driver will continue to probe. Because there are different variants of the controller that may have multiple reset signals, the code will find all reset(s) specified and de-assert them. Signed-off-by: Dinh Nguyen <dinguyen@kernel.org> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
2019-09-10rtc: meson: mark PM functions as __maybe_unusedArnd Bergmann1-4/+3
The meson_vrtc_set_wakeup_time() function is only used by the PM functions and causes a warning when they are disabled: drivers/rtc/rtc-meson-vrtc.c:32:13: error: unused function 'meson_vrtc_set_wakeup_time' [-Werror,-Wunused-function] Remove the #ifdef around the callers and add a __maybe_unused annotation as a more reliable way to avoid these warnings. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Kevin Hilman <khilman@baylibre.com> Link: https://lore.kernel.org/r/20190906152438.1533833-1-arnd@arndb.de Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-09-10rtc: sc27xx: Remove clearing SPRD_RTC_POWEROFF_ALM_FLAG flagBaolin Wang1-1/+1
The SPRD_RTC_POWEROFF_ALM_FLAG flag is used to indicate if a poweroff alarm is set, which can power on the system when system in power-off status. And the bootloader will validate this flag to check if the booting mode is alarm booting mode, thus we should not clear this flag in kernel, instead bootloader will clear this flag after checking the booting mode. Signed-off-by: Baolin Wang <baolin.wang@linaro.org> Link: https://lore.kernel.org/r/1f75310242de75b14d8973538bf96efffb395daf.1567666894.git.baolin.wang@linaro.org Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
2019-09-10ath9k: release allocated buffer if timed outNavid Emamdoost1-0/+1
In ath9k_wmi_cmd, the allocated network buffer needs to be released if timeout happens. Otherwise memory will be leaked. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-10ath9k_htc: release allocated buffer if timed outNavid Emamdoost1-0/+3
In htc_config_pipe_credits, htc_setup_complete, and htc_connect_service if time out happens, the allocated buffer needs to be released. Otherwise there will be memory leak. Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-10ath9k: Remove unneeded variable to store return valuezhong jiang1-3/+1
ath9k_reg_rmw_single do not need return value to cope with different cases. And change functon return type to void. Signed-off-by: zhong jiang <zhongjiang@huawei.com> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-10ath10k: add reorder and change PN check logic for mac80211Wen Gong1-2/+89
For sdio chip, if the rssi is not good, then it have some retry, firmware will indicate the msdu list of a ppdu with a hole, it means it lost the hole msdu, after the msdu retry from AP, the hole msdu will indicate from firmware later. The hole msdu's PN check will fail and the hole msdu will be dropped. PN check fail example: Sequence number PN number PN check status 3814 6101 success 3815 6102 success 3816 6103 success 3818 6105 success 3819 6106 success 3820 6107 success 3817 6104 fail The correct logic is reorder the msdu list and then do PN check. ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic and then do PN check in ieee80211_rx_h_decrypt of mac80211. example after reorder: Sequence number PN number PN check status 3814 6101 success 3815 6102 success 3816 6103 success 3817 6104 success 3818 6105 success 3819 6106 success 3820 6107 success Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-10ath10k: add mic bytes for pmf management packetWen Gong1-0/+8
For PMF case, the action,deauth,disassoc management need to encrypt by hardware, it need to reserve 8 bytes for encryption, otherwise the packet will be sent out with error format, then PMF case will fail. After add the 8 bytes, it will pass the PMF case. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1. Signed-off-by: Wen Gong <wgong@codeaurora.org> Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
2019-09-10platform/x86: asus-wmi: Refactor charge threshold to use the battery hooking APIKristian Klausen1-49/+99
At the same time use the official naming for the knobs. Tested on a Zenbook UX430UNR. Signed-off-by: Kristian Klausen <kristian@klausen.dk> Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
2019-09-10PCI: hv: Use bytes 4 and 5 from instance ID as the PCI domain numbersHaiyang Zhang1-1/+1
As recommended by Azure host team, the bytes 4, 5 have more uniqueness (info entropy) than bytes 8, 9 so use them as the PCI domain numbers. On older hosts, bytes 4, 5 can also be used -- no backward compatibility issues are introduced and the chance of collision is greatly reduced. In the rare cases of collision, the driver code detects and finds another number that is not in use. Suggested-by: Michael Kelley <mikelley@microsoft.com> Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com> Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com> Acked-by: Sasha Levin <sashal@kernel.org>
2019-09-10gpiolib: acpi: make acpi_can_fallback_to_crs() staticDmitry Torokhov2-17/+10
It is not used outside gpiolib-acpi.c module, so there is no need to export it. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Link: https://lore.kernel.org/r/20190904172624.GA76617@dtor-ws Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-09-10gpiolib: of: fix fallback quirks handlingDmitry Torokhov1-18/+9
We should only try to execute fallback quirks handling when previous call returned -ENOENT, and not when we did not get -EPROBE_DEFER. The other errors should be treated as hard errors: we did find the GPIO description, but for some reason we failed to handle it properly. The fallbacks should only be executed when previous handlers returned -ENOENT, which means the mapping/description was not found. Also let's remove the explicit deferral handling when iterating through GPIO suffixes: it is not needed anymore as we will not be calling fallbacks for anything but -ENOENT. Fixes: df451f83e1fc ("gpio: of: fix Freescale SPI CS quirk handling") Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Link: https://lore.kernel.org/r/20190903231856.GA165165@dtor-ws Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2019-09-10spi: bcm2835: Work around DONE bit erratumLukas Wunner1-2/+12
Commit 3bd7f6589f67 ("spi: bcm2835: Overcome sglist entry length limitation") amended the BCM2835 SPI driver with support for DMA transfers whose buffers are not aligned to 4 bytes and require more than one sglist entry. When testing this feature with upcoming commits to speed up TX-only and RX-only transfers, I noticed that SPI transmission sometimes breaks. A function introduced by the commit, bcm2835_spi_transfer_prologue(), performs one or two PIO transmissions as a prologue to the actual DMA transmission. It turns out that the breakage goes away if the DONE bit in the CS register is set when ending such a PIO transmission. The DONE bit signifies emptiness of the TX FIFO. According to the spec, the bit is of type RO, so writing it should never have any effect. Perhaps the spec is wrong and the bit is actually of type RW1C. E.g. the I2C controller on the BCM2835 does have an RW1C DONE bit which needs to be cleared by the driver. Another, possibly more likely explanation is that it's a hardware erratum since the issue does not occur consistently. Either way, amend bcm2835_spi_transfer_prologue() to always write the DONE bit. Usually a transmission is ended by bcm2835_spi_reset_hw(). If the transmission was successful, the TX FIFO is empty and thus the DONE bit is set when bcm2835_spi_reset_hw() reads the CS register. The bit is then written back to the register, so we happen to do the right thing. However if DONE is not set, e.g. because transmission is aborted with a non-empty TX FIFO, the bit won't be written by bcm2835_spi_reset_hw() and it seems possible that transmission might subsequently break. To be on the safe side, likewise amend bcm2835_spi_reset_hw() to always write the bit. Tested-by: Nuno Sá <nuno.sa@analog.com> Signed-off-by: Lukas Wunner <lukas@wunner.de> Acked-by: Stefan Wahren <wahrenst@gmx.net> Acked-by: Martin Sperl <kernel@martin.sperl.org> Link: https://lore.kernel.org/r/edb004dff4af6106f6bfcb89e1a96391e96eb857.1564825752.git.lukas@wunner.de Signed-off-by: Mark Brown <broonie@kernel.org>
2019-09-10Merge tag 'intel-gpio-v5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/andy/linux-gpio-intel into develLinus Walleij4-49/+55
intel-gpio for v5.4-1 The clean up of IRQ chip initialization has been done in few drivers. Stale record in MAINTAINERS database is removed. The following is an automated git shortlog grouped by driver: intel-mid: - Pass irqchip when adding gpiochip - MAINTAINERS: Remove stale record for gpio-intel-mid.c lynxpoint: - Pass irqchip when adding gpiochip merrifield: - Pass irqchip when adding gpiochip pch: - Use dev_get_drvdata
2019-09-10regulator: uniphier: Add Pro5 USB3 VBUS supportKunihiko Hayashi1-0/+4
Pro5 SoC has same scheme of USB3 VBUS as Pro4, so the data for Pro5 is equivalent to Pro4. Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com> Link: https://lore.kernel.org/r/1568080304-1572-1-git-send-email-hayashi.kunihiko@socionext.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-09-10regulator: fixed: add possibility to enable by clockPhilippe Schenker1-3/+80
This commit adds the possibility to choose the compatible "regulator-fixed-clock" in devicetree. This is a special regulator-fixed that has to have a clock, from which the regulator gets switched on and off. Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com> Link: https://lore.kernel.org/r/20190910062103.39641-2-philippe.schenker@toradex.com Signed-off-by: Mark Brown <broonie@kernel.org>
2019-09-10regulator: s2mps11: Consistently use local variableKrzysztof Kozlowski1-1/+1
The value under 's2mps11->ext_control_gpiod[i]' is assigned to local variable and used in probe in one place before. Use it consistently later so code will be easier to read. Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org> Link: https://lore.kernel.org/r/20190909155723.24734-1-krzk@kernel.org Signed-off-by: Mark Brown <broonie@kernel.org>
2019-09-10usb-storage: export symbols in USB_STORAGE namespaceMatthias Maennich15-0/+16
Modules using these symbols are required to explicitly import the namespace. This patch was generated with the following steps and serves as a reference to use the symbol namespace feature: 1) Define DEFAULT_SYMBOL_NAMESPACE in the corresponding Makefile 2) make (see warnings during modpost about missing imports) 3) make nsdeps Instead of a DEFAULT_SYMBOL_NAMESPACE definition, the EXPORT_SYMBOL_NS variants can be used to explicitly specify the namespace. The advantage of the method used here is that newly added symbols are automatically exported and existing ones are exported without touching their respective EXPORT_SYMBOL macro expansion. Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Matthias Maennich <maennich@google.com> Signed-off-by: Jessica Yu <jeyu@kernel.org>
2019-09-10usb-storage: remove single-use define for debuggingMatthias Maennich2-3/+1
USB_STORAGE was defined as "usb-storage: " and used in a single location as argument to printk. In order to be able to use the name 'USB_STORAGE', drop the definition and use the string directly for the printk call. Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Matthias Maennich <maennich@google.com> Signed-off-by: Jessica Yu <jeyu@kernel.org>
2019-09-10net/mlx4_en: ethtool: make array modes static const, makes object smallerColin Ian King1-1/+1
Don't populate the array modes on the stack but instead make it static const. Makes the object code smaller by 303 bytes. Before: text data bss dec hex filename 51240 5008 1312 57560 e0d8 mellanox/mlx4/en_ethtool.o After: text data bss dec hex filename 50937 5008 1312 57257 dfa9 mellanox/mlx4/en_ethtool.o (gcc version 9.2.1, amd64) Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10net/ibmvnic: Fix missing { in __ibmvnic_resetMichal Suchanek1-1/+1
Commit 1c2977c09499 ("net/ibmvnic: free reset work of removed device from queue") adds a } without corresponding { causing build break. Fixes: 1c2977c09499 ("net/ibmvnic: free reset work of removed device from queue") Signed-off-by: Michal Suchanek <msuchanek@suse.de> Reviewed-by: Tyrel Datwyler <tyreld@linux.ibm.com> Reviewed-by: Juliet Kim <julietk@linux.vnet.ibm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-10drm/lima: fix lima_gem_wait() return valueVasily Khoruzhick1-1/+1
drm_gem_reservation_object_wait() returns 0 if it succeeds and -ETIME if it timeouts, but lima driver assumed that 0 is error. Cc: stable@vger.kernel.org Fixes: a1d2a6339961e ("drm/lima: driver for ARM Mali4xx GPUs") Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Qiang Yu <yuq825@gmail.com> Link: https://patchwork.freedesktop.org/patch/msgid/20190908024800.23229-1-anarsoul@gmail.com
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.