| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: remove dead config symbols from SH code
sh: Kill off broken snapgear ds1302 code.
sh: Add a dummy vga.h.
rtc: rtc-sh: Zero out tm value for invalid rtc states.
rtc: sh-rtc: Handle rtc_device_register() failure properly.
sh: Fix heartbeart on Solution Engine series
sh: Remove SCI_NPORTS from sh-sci.h
sh: Fix up PAGE_KERNEL_PCC() for nommu.
sh: hs7751rvoip: Kill off dead IPR IRQ mappings.
sh: hs7751rvoip: irq.c needs linux/interrupt.h.
sh: Kill off __{copy,clear}_user_page().
sh: Optimized copy_{to,from}_user_page() for SH-4.
sh: Wire up clear_user_highpage().
sh: Kill off the remaining ST40 cruft.
superhyway: Handle device_register() retval properly.
sh: kgdb sysrq depends on magic sysrq.
sh: Add -Werror for clean directories.
sh: Fix up kgdb build with modular sh-sci.
sh: Export __{s,u}divsi3_i4i on all CPUs.
sh: Fix up kgdb-on-NMI branch target.
...
|
|
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: fix one-shot timer mode
[ARM] 4645/1: Cyberpro: Trivial fix to restore 16bpp mode.
[ARM] 4644/2: fix flush_kern_tlb_range() in module space
[ARM] Allow watchdog drivers to be selected again
[ARM] 4633/1: omap build fix when FB enabled
[ARM] 4642/2: netX: default config for netx based boards
[ARM] 4641/2: netX: fix kobject_name type
[ARM] Fix iop3xx macro
|
|
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
Add UNPLUG traces to all appropriate places
block: fix requeue handling in blk_queue_invalidate_tags()
mmc: Fix sg helper copy-and-paste error
pktcdvd: fix BUG caused by sysfs module reference semantics change
ioprio: allow sys_ioprio_set() value of 0 to reset ioprio setting
cfq_idle_class_timer: add paranoid checks for jiffies overflow
cfq: fix IOPRIO_CLASS_IDLE delays
cfq: fix IOPRIO_CLASS_IDLE accounting
|
|
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (37 commits)
[POWERPC] EEH: Make sure warning message is printed
[POWERPC] Make altivec code in swsusp_32.S depend on CONFIG_ALTIVEC
[POWERPC] windfarm: Fix windfarm thread freezer interaction
[POWERPC] Fix si_addr value on low level hash failures
[POWERPC] Refresh ppc64_defconfig and enable pasemi-related options
[POWERPC] pasemi: Update defconfig
[POWERPC] iSeries: Fix ref counting in vio setup
[POWERPC] ] Fix memset size error
[POWERPC] Fix link errors for allyesconfig
[POWERPC] iSeries_init_IRQ non-PCI tidy
[POWERPC] Change fallocate to match unistd.h on powerpc
[POWERPC] EEH: Avoid crash on null device
[POWERPC] EEH: Drivers that need reset trump others
[POWERPC] EEH: Clean up comments
[POWERPC] Fix off-by-one error in setting decrementer on Book E/4xx (v2)
[POWERPC] Fix switch_slb handling of 1T ESID values
[POWERPC] Fix build failure when CONFIG_VIRT_CPU_ACCOUNTING is not defined
[POWERPC] Include udbg.h when using udbg_printf
[POWERPC] Fix cache line vs. block size confusion
[POWERPC] Fix sysctl table check failure on PowerMac
...
|
|
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6: (44 commits)
[NETLINK]: Fix unicast timeouts
[INET]: Remove per bucket rwlock in tcp/dccp ehash table.
[IPVS]: Synchronize closing of Connections
[IPVS]: Bind connections on stanby if the destination exists
[NET]: Remove Documentation/networking/pt.txt
[NET]: Remove Documentation/networking/routing.txt
[NET]: Remove Documentation/networking/ncsa-telnet
[NET]: Remove comx driver docs.
[NET]: Remove Documentation/networking/Configurable
[NET]: Clean proto_(un)register from in-code ifdefs
[IPSEC]: Fix crypto_alloc_comp error checking
[VLAN]: Fix SET_VLAN_INGRESS_PRIORITY_CMD ioctl
[NETNS]: Fix compiler error in net_namespace.c
[TTY]: Use tty_mode_ioctl() in network drivers.
[TTY]: Fix network driver interactions with TCGET/SET calls.
[PKT_SCHED] CLS_U32: Fix endianness problem with u32 classifier hash masks.
[NET]: Removing duplicit #includes
[NET]: Let USB_USBNET always select MII.
[RRUNNER]: Do not muck with sysctl_{r,w}mem_max
[DLM] lowcomms: Do not muck with sysctl_rmem_max.
...
|
|
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.
Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
Cyberpro: when user requests 16bpp, use it and not 24bpp.
There was a missing break causing requests for 16bpp mode
to end up in 24bpp mode.
Signed-off-by: Jan Rinze Peterzon <janrinze@home.nl>
Acked-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Commit 45711f1a ("[SG] Update drivers to use sg helpers") had the
following bogus change in drivers/mmc/card/queue.c:
> - src_buf = page_address(src->page) + src->offset;
> + src_buf = sg_virt(dst);
(Notice that "src" is converted to "dst"). Turn this "dst" back into
the intended "src".
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
pkt_setup_dev() expects module reference to be held on invocation.
This used to be true for sysfs callbacks but not anymore. Test and
grab module reference around pkt_setup_dev() in
class_pktcdvd_store_add().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
|
|
|
|
When I fixed the windfarm freezer interaction first in commit
1ed2ddf380e19dafeec2150ca709ef7f4a67cd21, an earlier patch than the one
I came up with after comments was committed. This has come back to haunt
us now because commit d5d8c5976d6adeddb8208c240460411e2198b393 changed
the freezer to no long send signals. Fix it by removing the windfarm
thread's signal logic and restoring the original try_to_freeze().
We could simply revert 1ed2ddf380e19dafeec2150ca709ef7f4a67cd21 now
but I feel that the assertion that no signal is delivered to the
windfarm thread needs not be there.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Paul Mackerras <paulus@samba.org>
|
|
We conciously make a change here - we permit mode and speed setting to
be done in things like SLIP mode. There isn't actually a technical
reason to disallow this. It's usually a silly thing to do but we can
do it and soemone might wish to do so.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dave Miller noted various cases where line disciplines for things like
ppp go poking around in termios themselves in ways that broke with the
new termios code. Rather than have them all learning about termios
internals provide proper methods for this
- tty_mode_ioctl()
This handles all the terminal mode handling for speed/carrier
etc and none of the methods are ldisc dependant so they can be called
by any user
- tty_perform_flush()
This extracts the flush functionality and enables pppd the ppp
layer to share it cleanly.
The existing n_tty_ioctl code is refactored in this patch to provide
the new functions and to call them itself appropriately. This patch
has no (intended) behaviour changes and simply prepares for the other
fixes.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All this USB_USBNET_MII trickery is simply not worth it considering how
few code it saves.
As a side effect, this also fixes the following compile error reported
by Toralf Förster:
<-- snip -->
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `usbnet_set_settings':
(.text+0xf1876): undefined reference to `mii_ethtool_sset'
drivers/built-in.o: In function `usbnet_get_settings':
(.text+0xf1836): undefined reference to `mii_ethtool_gset'
drivers/built-in.o: In function `usbnet_get_link':
(.text+0xf18d6): undefined reference to `mii_link_ok'
drivers/built-in.o: In function `usbnet_nway_reset':
(.text+0xf18f6): undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers have no business changing these values.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It'd also be nice to mention "containers" somewhere in the help text
(I'm assuming that's what it's for?).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Changes made on 18-sep to fix skb handling in the pppol2tp driver
broke the transmit and receive paths. Users are only running into this
now because distros are now using 2.6.23 and I must have messed up
when I tested the change.
For receive, we now do our own calculation of how much to pull from
the skb (variable length L2TP header) rather than using
skb_transport_offset(). Also, if the skb isn't a data packet, it must
be passed back to UDP with skb->data pointing to the UDP header.
For transmit, make sure skb->sk is set up because ip_queue_xmit()
needs it.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Follows the changes of some of the other RTC drivers. If the tm
value is bogus, just zero it out. Adds some sanity for RTC_RD_TIME.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Currently if rtc_device_register() fails we have an IS_ERR() on
the wrong pointer, which causes this to always be skipped. Fix
this up to actually check the right pointer. The return value
was always correct, even though the check was wrong.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
When SH7710 and SH7712 are used, SCI_NPORTS redefined.
Remove it.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
The ST40 stuff in-tree hasn't built for some time, and hasn't been
updated for over 3 years. ST maintains their own out-of-tree changes
and rebases occasionally, and that's ultimately where all of the ST40
users go anyways.
In order for the ST40 code to be brought up to date most of the stuff
removed in this changeset would have to be rewritten anyways, so there's
very little benefit in keeping the remnants around either.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Since patch "fw-sbp2: use an own workqueue (fix system responsiveness)"
increased parallelism between fw-sbp2 and fw-core, it was possible that
fw-sbp2 didn't release the SCSI device when the FireWire device was
disconnected.
This happened if sbp2_update() ran during sbp2_login(), because a bus
reset occurred during sbp2_login(). The sbp2_login() work would [try
to] reschedule itself because it failed due to the bus reset, and it
would _not_ drop its reference on the target. However, sbp2_update()
would schedule sbp2_login() too before sbp2_login() rescheduled itself
and hence sbp2_update() would take an additional reference. And then
we would have one reference too many.
The fix is to _always_ drop the reference when leaving the sbp2_login()
work. If the sbp2_login() work reschedules itself, it takes a
reference, but only if it wasn't already rescheduled by sbp2_update().
Ditto in the sbp2_reconnect() work.
The resulting code is actually simpler than before: We _always_ take
a reference when successfully scheduling work. And we _always_ drop
a reference when leaving a workqueue job. No exceptions.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
|
|
* 'drm-patches' of master.kernel.org:/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm: DRM: fix memset size error
drm: remove remnants of DRM_COPY_FROM/TO_USER_IOCTL
drm: remove second forward decleration of drm device struct.
|
|
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: handle broken cable reporting
pata_hpt37x: Fix outstanding bug reports on the HPT374 and 37x cable detect
ata_piix: Add additional PCI identifier for 40 wire short cable
pata_serverworks: Fix problem with some drive combinations
libata: Don't disable dipm with SET FEATURES
libata and bogus LBA48 drives
|
|
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
phylib: Silence driver registration
phylib: Add ID for Marvell 88E1240
82596: free nonexistent resource fix
SUNHME: Fix missing NETIF_F_VLAN_CHALLENGED on PCI happy meals
|
|
The size passing to memset is wrong.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
This is a bug in the savage driver since I introduced these changes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Signed-off-by: Dave Airlie <airlied@linux.ie>
|
|
Keeping the list in sync with the old IDE driver
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Remove panic from phonedev. See
http://bugzilla.kernel.org/show_bug.cgi?id=9266
for details (phonedev panics if unregistering device not registered).
Signed-off-by: Matti Linnanvuori <mattilinnanvuori@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
commit 4ae3f847e49e3787eca91bced31f8fd328d50496 ("md: raid5: fix
clearing of biofill operations") did not get applied correctly,
presumably due to substantial similarities between handle_stripe5 and
handle_stripe6.
This patch moves the chunk of new code from handle_stripe6 (where it isn't
needed (yet)) to handle_stripe5.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: "Dan Williams" <dan.j.williams@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Make virtcons_probe() __devinit.
Fixes this section warning:
WARNING: vmlinux.o(.text+0x14c10b): Section mismatch: reference to .init.text:hvc_alloc (between 'virtcons_probe' and 'ac_register_board')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Change the name of this data to use a name (suffix) that is whitelisted
by MODPOST so that the section warning is fixed (not generated).
WARNING: vmlinux.o(.data+0x1b140): Section mismatch: reference to .init.text:m48t59_rtc_probe (between 'm48t59_rtc_platdrv' and 'm48t59_nvram_attr')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Fix 'and' typo (PT_WRITE_OK is defined 2)
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drivers/serial/8250_early.c:80: warning: conflicting types for built-in function `putc'
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
max_phys_segments and max_sectors were swapped
Signed-off-by: Vasily Averin <vvs@sw.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Karsten Keil <kkeil@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
One or two ancient drives predated the cable spec and didn't sent the
valid bits for the field. I had hoped to leave this out of libata as a
piece of historical annoyance but a recent CD drive shows the same bug so
we have to import support for it.
Same concept as Bartlomiej's changes old IDE except that as we have
centralised blacklists we can avoid keeping another private table of stuff
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
- Read frequency correctly
- Correct cable detect handling
- Fix wrong filter test
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Keeping the list in sync with the old IDE driver
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
The driver used the channel not the device number for deciding where to
load some timing parameters. Also change so that we clear the UDMA field
as the old driver did. Not believed neccessary but does no harm.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
It gets quite verbose to see every single PHY driver being registered
by default.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
Add PHY IDs for Marvell 88E1240. It seems to have close enough programming
models to 1111/1112 for basic support at least.
Also clean up whitespace in the ID list a bit.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
During booting of last vanilla kernel I got:
Trying to free nonexistent resource...
This because of if "ENABLE_APRICOT" is on we do:
request_region(ioaddr,...)
if (checksum test failed)
goto out1;
dev->base_addr = ioaddr;//<-here mistake
out1:
release_region(dev->base_addr,...)
This change fixes this bug for me.
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
No HME parts can do VLANs correctly.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
|
|
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: bugfixes for leds-gpio
|
|
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
PCI: Add Kconfig option to disable deprecated pci_find_* API
PCI: pciserial_resume_one ignored return value of pci_enable_device
PCI Hotplug: cpqhp_pushbutton_thread(): remove a pointless if() check
PCI: make pci_match_device() static
PCI: Remove 3 incorrect MSI quirks.
PCI: Add MSI INTX_DISABLE quirks for ATI SB700/800 SATA and IXP SB400 USB
PCI: Add quirk for devices which disable MSI when INTX_DISABLE is set.
PCI: Add MSI quirk for ServerWorks HT1000 PCIX bridge.
PCI: Revert "PCI: disable MSI by default on systems with Serverworks HT1000 chips"
|
|
Three bugfixes to the leds-gpio driver, plus minor whitespace tweaks:
- Do the INIT_WORK() before registering each LED, so if its trigger
becomes immediately active it can schedule work without oopsing..
- Use normal registration, not platform_driver_probe(), so that
devices appearing "late" (hotplug type) can still be bound.
- Mark the driver remove code as "__devexit", preventing oopses
when the underlying device is removed.
These issues came up when using this driver with some GPIO expanders
living on serial busses, which act unlike "normal" platform devices:
they can appear and vanish along with the serial bus driver.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: fix IDE_HFLAG_NO_ATAPI_DMA handling in config_drive_for_dma()
ide: move ide_fixstring() documentation to ide-iops.c from ide.h
ide: add missing #ifdef/#endif CONFIG_IDE_TASK_IOCTL
ide: fix ide_find_dma_mode() to print human-readable info
ide: add missing rq.ref_count initialization to ide_diag_taskfile()
ide: clear HOB bit for REQ_TYPE_ATA_TASK requests in ide_end_drive_cmd()
ide: check rq->cmd_type in drive_cmd_intr()
ide/Kconfig: fix BLK_DEV_OFFBOARD dependencies
ide: unexport ide_fix_driveid
ide/Kconfig: add IDEDISK_MULTI_MODE text adapted from hdparm manual page
ide: do_identify() string termination fix
piix: add support for ICH7 on Acer 5602aWLMi
|
Linus Torvalds
Alan D. Brunelle
Jan Rinze
Roland Dreier
Tejun Heo
Paul Mackerras
Johannes Berg
Alan Cox
Adrian Bunk
David S. Miller
Rusty Russell
James Chapman
Paul Mundt
Nobuhiro Iwamatsu
Stefan Richter
Li Zefan
Dave Airlie
Alan Cox
Matti Linnanvuori
Neil Brown
Randy Dunlap
Roel Kluin
Yinghai Lu
Vasily Averin
Olof Johansson
Evgeniy Dushistov
David Miller
David Brownell