Age | Commit message (Collapse) | Author | Files | Lines |
|
The kernel test robot reports a boot failure with qemu in 5.5-rc,
referencing commit 2203cbf2c8b5 ("net: sfp: move fwnode parsing into
sfp-bus layer"). This is caused by phylink_create() being passed a
NULL fwnode, causing fwnode_property_get_reference_args() to return
-EINVAL.
Don't attempt to attach to a SFP bus if we have no fwnode, which
avoids this issue.
Reported-by: kernel test robot <rong.a.chen@intel.com>
Fixes: 2203cbf2c8b5 ("net: sfp: move fwnode parsing into sfp-bus layer")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
pull-request: can 2020-01-02
this is a pull request of 9 patches for net/master.
The first 5 patches target all the tcan4x5x driver. The first 3 patches
of them are by Dan Murphy and Sean Nyekjaer and improve the device
initialization (power on, reset and get device out of standby before
register access). The next patch is by Dan Murphy and disables the INH
pin device-state if the GPIO is unavailable. The last patch for the
tcan4x5x driver is by Gustavo A. R. Silva and fixes an inconsistent
PTR_ERR check in the tcan4x5x_parse_config() function.
The next patch is by Oliver Hartkopp and targets the generic CAN device
infrastructure. It ensures that an initialized headroom in outgoing CAN
sk_buffs (e.g. if injected by AF_PACKET).
The last 2 patches are by Johan Hovold and fix the kvaser_usb and gs_usb
drivers by always using the current alternate setting not blindly the
first one.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to dump the FECs registers the clocks have to be ticking,
otherwise a data abort occurs. Add calls to runtime PM so they are
enabled and later disabled.
Fixes: e8fcfcd5684a ("net: fec: optimize the clock management to save power")
Reported-by: Chris Healy <Chris.Healy@zii.aero>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before ip_tunnel_ecn_encap() and udp_tunnel_xmit_skb() we should filter
tos value by RT_TOS() instead of using config tos directly.
vxlan_get_route() would filter the tos to fl4.flowi4_tos but we didn't
return it back, as geneve_get_v4_rt() did. So we have to use RT_TOS()
directly in function ip_tunnel_ecn_encap().
Fixes: 206aaafcd279 ("VXLAN: Use IP Tunnels tunnel ENC encap API")
Fixes: 1400615d64cf ("vxlan: allow setting ipv6 traffic class")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_port_set_cmode() relies on cmode stored in struct
mv88e6xxx_port to skip cmode update when the requested value matches the
cached value. It turns out that mv88e6xxx_port_hidden_write() might
change the port cmode setting as a side effect, so we can't rely on the
cached value to determine that cmode update in not necessary.
Force cmode update in mv88e6341_port_set_cmode(), to make
serdes configuration work again. Other mv88e6xxx_port_set_cmode()
callers keep the current behaviour.
This fixes serdes configuration of the 6141 switch on SolidRun Clearfog
GT-8K.
Fixes: 7a3007d22e8 ("net: dsa: mv88e6xxx: fully support SERDES on Topaz family")
Reported-by: Denis Odintsov <d.odintsov@traviangames.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under load, the RX side of the mscan driver can get stuck while TX still
works. Restarting the interface locks up the system. This behaviour
could be reproduced reliably on a MPC5121e based system.
The patch fixes the return value of the NAPI polling function (should be
the number of processed packets, not constant 1) and the condition under
which IRQs are enabled again after polling is finished.
With this patch, no more lockups were observed over a test period of ten
days.
Fixes: afa17a500a36 ("net/can: add driver for mscan family & mpc52xx_mscan")
Signed-off-by: Florian Faber <faber@faberman.de>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Make sure to always use the descriptors of the current alternate setting
to avoid future issues when accessing fields that may differ between
settings.
Signed-off-by: Johan Hovold <johan@kernel.org>
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Make sure to use the current alternate setting when verifying the
interface descriptors to avoid binding to an invalid interface.
Failing to do so could cause the driver to misbehave or trigger a WARN()
in usb_submit_urb() that kernels with panic_on_warn set would choke on.
Fixes: aec5fb2268b7 ("can: kvaser_usb: Add support for Kvaser USB hydra family")
Cc: stable <stable@vger.kernel.org> # 4.19
Cc: Jimmy Assarsson <extja@kvaser.com>
Cc: Christer Beskow <chbe@kvaser.com>
Cc: Nicklas Johansson <extnj@kvaser.com>
Cc: Martin Henriksson <mh@kvaser.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix inconsistent IS_ERR and PTR_ERR in tcan4x5x_parse_config().
The proper pointer to be passed as argument is tcan4x5x->device_wake_gpio.
This bug was detected with the help of Coccinelle.
Fixes: 2de497356955 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If the device state GPIO is not connected to the host then disable the
INH output from the TCAN device per section 8.3.5 of the data sheet.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It's a good idea to reset a ip-block/spi device before using it, this
patch will reset the device.
And a generic reset function if needed elsewhere.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The tcan4x5x_parse_config() function now performs action on the device
either reading or writing and a reset. If the devive has a switchable
power supppy (i.e. regulator is managed) it needs to be turned on.
So turn on the regulator if available. If the parsing fails, turn off
the regulator.
Fixes: 2de497356955 ("can: tcan45x: Make wake-up GPIO an optional GPIO")
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The m_can tries to detect if Non ISO Operation is available while in
standby mode, this function results in the following error:
| tcan4x5x spi2.0 (unnamed net_device) (uninitialized): Failed to init module
| tcan4x5x spi2.0: m_can device registered (irq=84, version=32)
| tcan4x5x spi2.0 can2: TCAN4X5X successfully initialized.
When the tcan device comes out of reset it goes in standby mode. The
m_can driver tries to access the control register but fails due to the
device being in standby mode.
So this patch will put the tcan device in normal mode before the m_can
driver does the initialization.
Fixes: 5443c226ba91 ("can: tcan4x5x: Add tcan4x5x driver to the kernel")
Cc: stable@vger.kernel.org
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Acked-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Pull networking fixes from David Miller:
1) Fix big endian overflow in nf_flow_table, from Arnd Bergmann.
2) Fix port selection on big endian in nft_tproxy, from Phil Sutter.
3) Fix precision tracking for unbound scalars in bpf verifier, from
Daniel Borkmann.
4) Fix integer overflow in socket rcvbuf check in UDP, from Antonio
Messina.
5) Do not perform a neigh confirmation during a pmtu update over a
tunnel, from Hangbin Liu.
6) Fix DMA mapping leak in dpaa_eth driver, from Madalin Bucur.
7) Various PTP fixes for sja1105 dsa driver, from Vladimir Oltean.
8) Add missing to dummy definition of of_mdiobus_child_is_phy(), from
Geert Uytterhoeven
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (54 commits)
hsr: fix slab-out-of-bounds Read in hsr_debugfs_rename()
net/sched: add delete_empty() to filters and use it in cls_flower
tcp: Fix highest_sack and highest_sack_seq
ptp: fix the race between the release of ptp_clock and cdev
net: dsa: sja1105: Reconcile the meaning of TPID and TPID2 for E/T and P/Q/R/S
Documentation: net: dsa: sja1105: Remove text about taprio base-time limitation
net: dsa: sja1105: Remove restriction of zero base-time for taprio offload
net: dsa: sja1105: Really make the PTP command read-write
net: dsa: sja1105: Take PTP egress timestamp by port, not mgmt slot
cxgb4/cxgb4vf: fix flow control display for auto negotiation
mlxsw: spectrum: Use dedicated policer for VRRP packets
mlxsw: spectrum_router: Skip loopback RIFs during MAC validation
net: stmmac: dwmac-meson8b: Fix the RGMII TX delay on Meson8b/8m2 SoCs
net/sched: act_mirred: Pull mac prior redir to non mac_header_xmit device
net_sched: sch_fq: properly set sk->sk_pacing_status
bnx2x: Fix accounting of vlan resources among the PFs
bnx2x: Use appropriate define for vlan credit
of: mdio: Add missing inline to of_mdiobus_child_is_phy() dummy
net: phy: aquantia: add suspend / resume ops for AQR105
dpaa_eth: fix DMA mapping leak
...
|
|
In a case when a ptp chardev (like /dev/ptp0) is open but an underlying
device is removed, closing this file leads to a race. This reproduces
easily in a kvm virtual machine:
ts# cat openptp0.c
int main() { ... fp = fopen("/dev/ptp0", "r"); ... sleep(10); }
ts# uname -r
5.5.0-rc3-46cf053e
ts# cat /proc/cmdline
... slub_debug=FZP
ts# modprobe ptp_kvm
ts# ./openptp0 &
[1] 670
opened /dev/ptp0, sleeping 10s...
ts# rmmod ptp_kvm
ts# ls /dev/ptp*
ls: cannot access '/dev/ptp*': No such file or directory
ts# ...woken up
[ 48.010809] general protection fault: 0000 [#1] SMP
[ 48.012502] CPU: 6 PID: 658 Comm: openptp0 Not tainted 5.5.0-rc3-46cf053e #25
[ 48.014624] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), ...
[ 48.016270] RIP: 0010:module_put.part.0+0x7/0x80
[ 48.017939] RSP: 0018:ffffb3850073be00 EFLAGS: 00010202
[ 48.018339] RAX: 000000006b6b6b6b RBX: 6b6b6b6b6b6b6b6b RCX: ffff89a476c00ad0
[ 48.018936] RDX: fffff65a08d3ea08 RSI: 0000000000000247 RDI: 6b6b6b6b6b6b6b6b
[ 48.019470] ... ^^^ a slub poison
[ 48.023854] Call Trace:
[ 48.024050] __fput+0x21f/0x240
[ 48.024288] task_work_run+0x79/0x90
[ 48.024555] do_exit+0x2af/0xab0
[ 48.024799] ? vfs_write+0x16a/0x190
[ 48.025082] do_group_exit+0x35/0x90
[ 48.025387] __x64_sys_exit_group+0xf/0x10
[ 48.025737] do_syscall_64+0x3d/0x130
[ 48.026056] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 48.026479] RIP: 0033:0x7f53b12082f6
[ 48.026792] ...
[ 48.030945] Modules linked in: ptp i6300esb watchdog [last unloaded: ptp_kvm]
[ 48.045001] Fixing recursive fault but reboot is needed!
This happens in:
static void __fput(struct file *file)
{ ...
if (file->f_op->release)
file->f_op->release(inode, file); <<< cdev is kfree'd here
if (unlikely(S_ISCHR(inode->i_mode) && inode->i_cdev != NULL &&
!(mode & FMODE_PATH))) {
cdev_put(inode->i_cdev); <<< cdev fields are accessed here
Namely:
__fput()
posix_clock_release()
kref_put(&clk->kref, delete_clock) <<< the last reference
delete_clock()
delete_ptp_clock()
kfree(ptp) <<< cdev is embedded in ptp
cdev_put
module_put(p->owner) <<< *p is kfree'd, bang!
Here cdev is embedded in posix_clock which is embedded in ptp_clock.
The race happens because ptp_clock's lifetime is controlled by two
refcounts: kref and cdev.kobj in posix_clock. This is wrong.
Make ptp_clock's sysfs device a parent of cdev with cdev_device_add()
created especially for such cases. This way the parent device with its
ptp_clock is not released until all references to the cdev are released.
This adds a requirement that an initialized but not exposed struct
device should be provided to posix_clock_register() by a caller instead
of a simple dev_t.
This approach was adopted from the commit 72139dfa2464 ("watchdog: Fix
the race between the release of watchdog_core_data and cdev"). See
details of the implementation in the commit 233ed09d7fda ("chardev: add
helper function to register char devs with a struct device").
Link: https://lore.kernel.org/linux-fsdevel/20191125125342.6189-1-vdronov@redhat.com/T/#u
Analyzed-by: Stephen Johnston <sjohnsto@redhat.com>
Analyzed-by: Vern Lovejoy <vlovejoy@redhat.com>
Signed-off-by: Vladis Dronov <vdronov@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For first-generation switches (SJA1105E and SJA1105T):
- TPID means C-Tag (typically 0x8100)
- TPID2 means S-Tag (typically 0x88A8)
While for the second generation switches (SJA1105P, SJA1105Q, SJA1105R,
SJA1105S) it is the other way around:
- TPID means S-Tag (typically 0x88A8)
- TPID2 means C-Tag (typically 0x8100)
In other words, E/T tags untagged traffic with TPID, and P/Q/R/S with
TPID2.
So the patch mentioned below fixed VLAN filtering for P/Q/R/S, but broke
it for E/T.
We strive for a common code path for all switches in the family, so just
lie in the static config packing functions that TPID and TPID2 are at
swapped bit offsets than they actually are, for P/Q/R/S. This will make
both switches understand TPID to be ETH_P_8021Q and TPID2 to be
ETH_P_8021AD. The meaning from the original E/T was chosen over P/Q/R/S
because E/T is actually the one with public documentation available
(UM10944.pdf).
Fixes: f9a1a7646c0d ("net: dsa: sja1105: Reverse TPID and TPID2")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The check originates from the initial implementation which was not based
on PTP time but on a standalone clock source. In the meantime we can now
program the PTPSCHTM register at runtime with the dynamic base time
(actually with a value that is 200 ns smaller, to avoid writing DELTA=0
in the Schedule Entry Points Parameters Table). And we also have logic
for moving the actual base time in the future of the PHC's current time
base, so the check for zero serves no purpose, since even if the user
will specify zero, that's not what will end up in the static config
table where the limitation is.
Fixes: 86db36a347b4 ("net: dsa: sja1105: Implement state machine for TAS with PTP clock source")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When activating tc-taprio offload on the switch ports, the TAS state
machine will try to check whether it is running or not, but will find
both the STARTED and STOPPED bits as false in the
sja1105_tas_check_running function. So the function will return -EINVAL
(an abnormal situation) and the kernel will keep printing this from the
TAS FSM workqueue:
[ 37.691971] sja1105 spi0.1: An operation returned -22
The reason is that the underlying function that gets called,
sja1105_ptp_commit, does not actually do a SPI_READ, but a SPI_WRITE. So
the command buffer remains initialized with zeroes instead of retrieving
the hardware state. Fix that.
Fixes: 41603d78b362 ("net: dsa: sja1105: Make the PTP command read-write")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PTP egress timestamp N must be captured from register PTPEGR_TS[n],
where n = 2 * PORT + TSREG. There are 10 PTPEGR_TS registers, 2 per
port. We are only using TSREG=0.
As opposed to the management slots, which are 4 in number
(SJA1105_NUM_PORTS, minus the CPU port). Any management frame (which
includes PTP frames) can be sent to any non-CPU port through any
management slot. When the CPU port is not the last port (#4), there will
be a mismatch between the slot and the port number.
Luckily, the only mainline occurrence with this switch
(arch/arm/boot/dts/ls1021a-tsn.dts) does have the CPU port as #4, so the
issue did not manifest itself thus far.
Fixes: 47ed985e97f5 ("net: dsa: sja1105: Add logic for TX timestamping")
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As per 802.3-2005, Section Two, Annex 28B, Table 28B-2 [1], when
_only_ Rx pause is enabled, both symmetric and asymmetric pause
towards local device must be enabled. Also, firmware returns the local
device's flow control pause params as part of advertised capabilities
and negotiated params as part of current link attributes. So, fix up
ethtool's flow control pause params fetch logic to read from acaps,
instead of linkattr.
[1] https://standards.ieee.org/standard/802_3-2005.html
Fixes: c3168cabe1af ("cxgb4/cxgbvf: Handle 32-bit fw port capabilities")
Signed-off-by: Surendra Mobiya <surendra@chelsio.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, VRRP packets and packets that hit exceptions during routing
(e.g., MTU error) are policed using the same policer towards the CPU.
This means, for example, that misconfiguration of the MTU on a routed
interface can prevent VRRP packets from reaching the CPU, which in turn
can cause the VRRP daemon to assume it is the Master router.
Fix this by using a dedicated policer for VRRP packets.
Fixes: 11566d34f895 ("mlxsw: spectrum: Add VRRP traps")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Alex Veber <alexve@mellanox.com>
Tested-by: Alex Veber <alexve@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a router interface (RIF) is created the MAC address of the backing
netdev is verified to have the same MSBs as existing RIFs. This is
required in order to avoid changing existing RIF MAC addresses that all
share the same MSBs.
Loopback RIFs are special in this regard as they do not have a MAC
address, given they are only used to loop packets from the overlay to
the underlay.
Without this change, an error is returned when trying to create a RIF
after the creation of a GRE tunnel that is represented by a loopback
RIF. 'rif->dev->dev_addr' points to the GRE device's local IP, which
does not share the same MSBs as physical interfaces. Adding an IP
address to any physical interface results in:
Error: mlxsw_spectrum: All router interface MAC addresses must have the
same prefix.
Fix this by skipping loopback RIFs during MAC validation.
Fixes: 74bc99397438 ("mlxsw: spectrum_router: Veto unsupported RIF MAC addresses")
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull SCSI fixes from James Bottomley:
"Four fixes and one spelling update, all in drivers: two in lpfc and
the rest in mp3sas, cxgbi and target"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: target/iblock: Fix protection error with blocks greater than 512B
scsi: libcxgbi: fix NULL pointer dereference in cxgbi_device_destroy()
scsi: lpfc: fix spelling mistakes of asynchronous
scsi: lpfc: fix build failure with DEBUGFS disabled
scsi: mpt3sas: Fix double free in attach error handling
|
|
GXBB and newer SoCs use the fixed FCLK_DIV2 (1GHz) clock as input for
the m250_sel clock. Meson8b and Meson8m2 use MPLL2 instead, whose rate
can be adjusted at runtime.
So far we have been running MPLL2 with ~250MHz (and the internal
m250_div with value 1), which worked enough that we could transfer data
with an TX delay of 4ns. Unfortunately there is high packet loss with
an RGMII PHY when transferring data (receiving data works fine though).
Odroid-C1's u-boot is running with a TX delay of only 2ns as well as
the internal m250_div set to 2 - no lost (TX) packets can be observed
with that setting in u-boot.
Manual testing has shown that the TX packet loss goes away when using
the following settings in Linux (the vendor kernel uses the same
settings):
- MPLL2 clock set to ~500MHz
- m250_div set to 2
- TX delay set to 2ns on the MAC side
Update the m250_div divider settings to only accept dividers greater or
equal 2 to fix the TX delay generated by the MAC.
iperf3 results before the change:
[ ID] Interval Transfer Bitrate Retr
[ 5] 0.00-10.00 sec 182 MBytes 153 Mbits/sec 514 sender
[ 5] 0.00-10.00 sec 182 MBytes 152 Mbits/sec receiver
iperf3 results after the change (including an updated TX delay of 2ns):
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-10.00 sec 927 MBytes 778 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 927 MBytes 777 Mbits/sec receiver
Fixes: 4f6a71b84e1afd ("net: stmmac: dwmac-meson8b: fix internal RGMII clock configuration")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Post-xmas food coma recovery fixes. Only three fixes for i915 since I
expect most people are holidaying.
i915:
- power management rc6 fix
- framebuffer tracking fix
- display power management ratelimit fix"
* tag 'drm-fixes-2019-12-28' of git://anongit.freedesktop.org/drm/drm:
drm/i915: Hold reference to intel_frontbuffer as we track activity
drm/i915/gt: Ratelimit display power w/a
drm/i915/pmu: Ensure monotonic rc6
|
|
Pull power management fixes from Rafael Wysocki:
"Fix compile test of the Tegra devfreq driver (Arnd Bergmann) and
remove redundant Kconfig dependencies from multiple devfreq drivers
(Leonard Crestez)"
* tag 'pm-5.5-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / devfreq: tegra: Add COMMON_CLK dependency
PM / devfreq: Drop explicit selection of PM_OPP
|
|
Pull libata fixes from Jens Axboe:
"Two things in here:
- First half of a series that fixes ahci_brcm, also marked for
stable. The other part of the series is going into 5.6 (Florian)
- sata_nv regression fix that is also marked for stable (Sascha)"
* tag 'libata-5.5-20191226' of git://git.kernel.dk/linux-block:
ata: ahci_brcm: Add missing clock management during recovery
ata: ahci_brcm: BCM7425 AHCI requires AHCI_HFLAG_DELAY_ENGINE
ata: ahci_brcm: Fix AHCI resources management
ata: libahci_platform: Export again ahci_platform_<en/dis>able_phys()
libata: Fix retrieving of active qcs
|
|
Pull block fixes from Jens Axboe:
"Only thing here are the changes from Arnd from last week, which now
have the appropriate header include to ensure they actually compile if
COMPAT is enabled"
* tag 'block-5.5-20191226' of git://git.kernel.dk/linux-block:
compat_ioctl: block: handle Persistent Reservations
compat_ioctl: block: handle add zone open, close and finish ioctl
compat_ioctl: block: handle BLKGETZONESZ/BLKGETNRZONES
compat_ioctl: block: handle BLKREPORTZONE/BLKRESETZONE
pktcdvd: fix regression on 64-bit architectures
|
|
Pull GPIO fixes from Linus Walleij:
"A set of fixes for the v5.5 series:
- Fix the build for the Xtensa driver.
- Make sure to set up the parent device for mpc8xxx.
- Clarify the look-up error message.
- Fix the usage of the line direction in the mockup device.
- Fix a type warning on the Aspeed driver.
- Remove the pointless __exit annotation on the xgs-iproc which is
causing a compilation problem.
- Fix up emultation of open drain outputs .get_direction()
- Fix the IRQ callbacks on the PCA953xx to use bitops and work
properly.
- Fix the Kconfig on the Tegra driver"
* tag 'gpio-v5.5-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tegra186: Allow building on Tegra194-only configurations
gpio: pca953x: Switch to bitops in IRQ callbacks
gpiolib: fix up emulated open drain outputs
MAINTAINERS: Append missed file to the database
gpio: xgs-iproc: remove __exit annotation for iproc_gpio_remove
gpio: aspeed: avoid return type warning
gpio: mockup: Fix usage of new GPIO_LINE_DIRECTION
gpio: Fix error message on out-of-range GPIO in lookup table
gpio: mpc8xxx: Add platform device to gpiochip->parent
gpio: xtensa: fix driver build
|
|
While testing max vlan configuration on the PF, firmware gets
assert as driver was configuring number of vlans more than what
is supported per port/engine, it was figured out that there is an
implicit vlan (hidden default vlan consuming hardware cam entry resource)
which is configured default for all the clients (PF/VFs) on client_init
ramrod by the adapter implicitly, so when allocating resources among the
PFs this implicit vlan should be considered or total vlan entries should
be reduced by one to accommodate that default/implicit vlan entry.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although it has same value as MAX_MAC_CREDIT_E2,
use MAX_VLAN_CREDIT_E2 appropriately.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The suspend/resume code for AQR107 works on AQR105 too.
This patch fixes issues with the partner not seeing the link down
when the interface using AQR105 is brought down.
Fixes: bee8259dd31f ("net: phy: add driver for aquantia phy")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the error path some fragments remain DMA mapped. Adding a fix
that unmaps all the fragments. Rework cleanup path to be simpler.
Fixes: 8151ee88bad5 ("dpaa_eth: use page backed rx buffers")
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The burning process requires to perform internal allocations of large
chunks of memory. This memory doesn't need to be contiguous and can be
safely allocated by vzalloc() instead of kzalloc(). This patch changes
such allocation to avoid possible out-of-memory failure.
Fixes: 410ed13cae39 ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: Vladyslav Tarasiuk <vladyslavt@mellanox.com>
Reviewed-by: Aya Levin <ayal@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Tested-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The downstream implementation of ahci_brcm.c did contain clock
management recovery, but until recently, did that outside of the
libahci_platform helpers and this was unintentionally stripped out while
forward porting the patch upstream.
Add the missing clock management during recovery and sleep for 10
milliseconds per the design team recommendations to ensure the SATA PHY
controller and AFE have been fully quiesced.
Fixes: eb73390ae241 ("ata: ahci_brcm: Recover from failures to identify devices")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Set AHCI_HFLAG_DELAY_ENGINE for the BCM7425 AHCI controller thus making
it conforming to the 'strict' AHCI implementation which this controller
is based on.
This solves long link establishment with specific hard drives (e.g.:
Seagate ST1000VM002-9ZL1 SC12) that would otherwise have to complete the
error recovery handling before finally establishing a succesful SATA
link at the desired speed.
We re-order the hpriv->flags assignment to also remove the NONCQ quirk
since we can set the flag directly.
Fixes: 9586114cf1e9 ("ata: ahci_brcmstb: add support MIPS-based platforms")
Fixes: 423be77daabe ("ata: ahci_brcmstb: add quirk for broken ncq")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The AHCI resources management within ahci_brcm.c is a little
convoluted, largely because it historically had a dedicated clock that
was managed within this file in the downstream tree. Once brough
upstream though, the clock was left to be managed by libahci_platform.c
which is entirely appropriate.
This patch series ensures that the AHCI resources are fetched and
enabled before any register access is done, thus avoiding bus errors on
platforms which clock gate the controller by default.
As a result we need to re-arrange the suspend() and resume() functions
in order to avoid accessing registers after the clocks have been turned
off respectively before the clocks have been turned on. Finally, we can
refactor brcm_ahci_get_portmask() in order to fetch the number of ports
from hpriv->mmio which is now accessible without jumping through hoops
like we used to do.
The commit pointed in the Fixes tag is both old and new enough not to
require major headaches for backporting of this patch.
Fixes: eba68f829794 ("ata: ahci_brcmstb: rename to support across Broadcom SoC's")
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 6bb86fefa086faba7b60bb452300b76a47cde1a5
("libahci_platform: Staticize ahci_platform_<en/dis>able_phys()") we are
going to need ahci_platform_{enable,disable}_phys() in a subsequent
commit for ahci_brcm.c in order to properly control the PHY
initialization order.
Also make sure the function prototypes are declared in
include/linux/ahci_platform.h as a result.
Cc: stable@vger.kernel.org
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
ata_qc_complete_multiple() is called with a mask of the still active
tags.
mv_sata doesn't have this information directly and instead calculates
the still active tags from the started tags (ap->qc_active) and the
finished tags as (ap->qc_active ^ done_mask)
Since 28361c40368 the hw_tag and tag are no longer the same and the
equation is no longer valid. In ata_exec_internal_sg() ap->qc_active is
initialized as 1ULL << ATA_TAG_INTERNAL, but in hardware tag 0 is
started and this will be in done_mask on completion. ap->qc_active ^
done_mask becomes 0x100000000 ^ 0x1 = 0x100000001 and thus tag 0 used as
the internal tag will never be reported as completed.
This is fixed by introducing ata_qc_get_active() which returns the
active hardware tags and calling it where appropriate.
This is tested on mv_sata, but sata_fsl and sata_nv suffer from the same
problem. There is another case in sata_nv that most likely needs fixing
as well, but this looks a little different, so I wasn't confident enough
to change that.
Fixes: 28361c403683 ("libata: add extra internal command")
Cc: stable@vger.kernel.org
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add missing export of ata_qc_get_active(), as per Pali.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
I stumbled over an old OSA model that claims to support DIAG_ASSIST,
but then rejects the cmd to query its DIAG capabilities.
In the old code this was ok, as the returned raw error code was > 0.
Now that we translate the raw codes to errnos, the "rc < 0" causes us
to fail the initialization of the device.
The fix is trivial: don't bail out when the DIAG query fails. Such an
error is not critical, we can still use the device (with a slightly
reduced set of features).
Fixes: 742d4d40831d ("s390/qeth: convert remaining legacy cmd callbacks")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During vnicc_init wanted_char should be compared to cur_char and not
to QETH_VNICC_DEFAULT. Without this patch there is no way to enforce
the default values as desired values.
Note, that it is expected, that a card comes online with default values.
This patch was tested with private card firmware.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Symptom: After vnicc/rx_bcast has been manually set to 0,
bridge_* sysfs parameters can still be set or written.
Only occurs on HiperSockets, as OSA doesn't support changing rx_bcast.
Vnic characteristics and bridgeport settings are mutually exclusive.
rx_bcast defaults to 1, so manually setting it to 0 should disable
bridge_* parameters.
Instead it makes sense here to check the supported mask. If the card
does not support vnicc at all, bridge commands are always allowed.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Symptom: Error message "Configuring the VNIC characteristics failed"
in dmesg whenever an OSA interface on z15 is set online.
The VNIC characteristics get re-programmed when setting a L2 device
online. This follows the selected 'wanted' characteristics - with the
exception that the INVISIBLE characteristic unconditionally gets
switched off.
For devices that don't support INVISIBLE (ie. OSA), the resulting
IO failure raises a noisy error message
("Configuring the VNIC characteristics failed").
For IQD, INVISIBLE is off by default anyways.
So don't unnecessarily special-case the INVISIBLE characteristic, and
thereby suppress the misleading error message on OSA devices.
Fixes: caa1f0b10d18 ("s390/qeth: add VNICC enable/disable support")
Signed-off-by: Alexandra Winter <wintera@linux.ibm.com>
Reviewed-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l3_dev_hsuid_store() initially checks the card state, but doesn't
take the conf_mutex to ensure that the card stays in this state while
being reconfigured.
Rework the code to take this lock, and drop a redundant state check in a
helper function.
Fixes: b333293058aa ("qeth: add support for af_iucv HiperSockets transport")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
qeth_l?_set_online() goes through a number of initialization steps, and
on any error uses qeth_l?_stop_card() to tear down the residual state.
The first initialization step is qeth_core_hardsetup_card(). When this
fails after having established a QDIO context on the device
(ie. somewhere after qeth_mpc_initialize()), qeth_l?_stop_card() doesn't
shut down this QDIO context again (since the card state hasn't
progressed from DOWN at this stage).
Even worse, we then call qdio_free() as final teardown step to free the
QDIO data structures - while some of them are still hooked into wider
QDIO infrastructure such as the IRQ list. This is inevitably followed by
use-after-frees and other nastyness.
Fix this by unconditionally calling qeth_qdio_clear_card() to shut down
the QDIO context, and also to halt/clear any pending activity on the
various IO channels.
Remove the naive attempt at handling the teardown in
qeth_mpc_initialize(), it clearly doesn't suffice and we're handling it
properly now in the wider teardown code.
Fixes: 4a71df50047f ("qeth: new qeth device driver")
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When do IPv6 tunnel PMTU update and calls __ip6_rt_update_pmtu() in the end,
we should not call dst_confirm_neigh() as there is no two-way communication.
Although GTP only support ipv4 right now, and __ip_rt_update_pmtu() does not
call dst_confirm_neigh(), we still set it to false to keep consistency with
IPv6 code.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTU update code is supposed to be invoked in response to real
networking events that update the PMTU. In IPv6 PMTU update function
__ip6_rt_update_pmtu() we called dst_confirm_neigh() to update neighbor
confirmed time.
But for tunnel code, it will call pmtu before xmit, like:
- tnl_update_pmtu()
- skb_dst_update_pmtu()
- ip6_rt_update_pmtu()
- __ip6_rt_update_pmtu()
- dst_confirm_neigh()
If the tunnel remote dst mac address changed and we still do the neigh
confirm, we will not be able to update neigh cache and ping6 remote
will failed.
So for this ip_tunnel_xmit() case, _EVEN_ if the MTU is changed, we
should not be invoking dst_confirm_neigh() as we have no evidence
of successful two-way communication at this point.
On the other hand it is also important to keep the neigh reachability fresh
for TCP flows, so we cannot remove this dst_confirm_neigh() call.
To fix the issue, we have to add a new bool parameter for dst_ops.update_pmtu
to choose whether we should do neigh update or not. I will add the parameter
in this patch and set all the callers to true to comply with the previous
way, and fix the tunnel code one by one on later patches.
v5: No change.
v4: No change.
v3: Do not remove dst_confirm_neigh, but add a new bool parameter in
dst_ops.update_pmtu to control whether we should do neighbor confirm.
Also split the big patch to small ones for each area.
v2: Remove dst_confirm_neigh in __ip6_rt_update_pmtu.
Suggested-by: David Miller <davem@davemloft.net>
Reviewed-by: Guillaume Nault <gnault@redhat.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The IP fragment is specified through user-defined field as the first
bit of the first user-defined word. We were previously trying to extract
it from the user-defined mask which could not possibly work. The ip_frag
is also supposed to be a boolean, if we do not cast it as such, we risk
overwriting the next fields in CFP_DATA(6) which would render the rule
inoperative.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since obj->frontbuffer is no longer protected by the struct_mutex, as we
are processing the execbuf, it may be removed. Mark the
intel_frontbuffer as rcu protected, and so acquire a reference to
the struct as we track activity upon it.
Closes: https://gitlab.freedesktop.org/drm/intel/issues/827
Fixes: 8e7cb1799b4f ("drm/i915: Extract intel_frontbuffer active tracking")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v5.4+
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218104043.3539458-1-chris@chris-wilson.co.uk
(cherry picked from commit da42104f589d979bbe402703fd836cec60befae1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
For very light workloads that frequently park, acquiring the display
power well (required to prevent the dmc from trashing the system) takes
longer than the execution. A good example is the igt_coherency selftest,
which is slowed down by an order of magnitude in the worst case with
powerwell cycling. To prevent frequent cycling, while keeping our fast
soft-rc6, use a timer to delay release of the display powerwell.
Fixes: 311770173fac ("drm/i915/gt: Schedule request retirement when timeline idles")
References: https://gitlab.freedesktop.org/drm/intel/issues/848
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191218093504.3477048-1-chris@chris-wilson.co.uk
(cherry picked from commit 81ff52b705775433a955b2746d37b87bdc89a3d0)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|