Age | Commit message (Collapse) | Author | Files | Lines |
|
Recent additions to the flower app private data have grouped the variables
of a given feature into a struct and added that struct to the main private
data struct.
In keeping with this, move all tunnel related private data to their own
struct. This has no affect on functionality but improves readability and
maintenance of the code.
Signed-off-by: John Hurley <john.hurley@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adds support for multiple memory units which are used for filter
offloads. Each filter is assigned a stats id, the MSBs of the id are
used to determine which memory unit the filter should be offloaded
to. The number of available memory units that could be used for filter
offload is obtained from HW. A simple round robin technique is used to
allocate and distribute the ids across memory units.
Signed-off-by: Pieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
QA tests report occasional timeouts on REIFY message replies. Profiling
of the two cmesg reply types under burst conditions, with a 12-core host
under heavy cpu and io load (stress --cpu 12 --io 12), show both PHY MTU
change and REIFY replies can exceed the 10ms timeout. The maximum MTU
reply wait under burst is 16ms, while the maximum REIFY wait under 40 VF
burst is 12ms. Using a 4 VF REIFY burst results in an 8ms maximum wait.
A larger VF burst does increase the delay, but not in a linear enough
way to justify a scaled REIFY delay. The worse case values between
MTU and REIFY appears close enough to justify a common timeout. Pick a
conservative 40ms to make a safer future proof common reply timeout. The
delay only effects the failure case.
Change the REIFY timeout mechanism to use wait_event_timeout() instead
of wait_event_interruptible_timeout(), to match the MTU code. In the
current implementation, theoretically, a signal could interrupt the
REIFY waiting period, with a return code of ERESTARTSYS. However, this is
caught under the general timeout error code EIO. I cannot see the benefit
of exposing the REIFY waiting period to signals with such a short delay
(40ms), while the MTU mechnism does not use the same logic. In the absence
of any reply (wakeup() call), both reply types will wake up the task after
the timeout period. The REIFY timeout applies to the entire representor
group being instantiated (e.g. VFs), while the MTU timeout apples to a
single PHY MTU change.
Signed-off-by: Fred Lotter <frederik.lotter@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The declaration of variable 'found' is one level too deep, fix this by
removing a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are various lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are lines that have indentation issues, fix these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
instance = kzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-01-15
This series contains updates to the ice driver only.
Bruce fixes an unused variable build warning, which was introduced with
the commit 2fd527b72bb6 ("net: ndo_bridge_setlink: Add extack"). Added
ethtool support for get_eeprom and get_eeprom_len operations. Added
support for bringing down the PHY link optional when the interface is
administratively downed.
Anirudh refactors the transmit scheduler functions, which results in
reduced code duplication and adds a helper function, which all the
scheduler functions call instead. Added an LED blinking handler to
ethtool. Reworked the queue management code to allow for reuse in
future XDP feature support. Updates the driver to be able to preserve
the aggregator list after reset by moving it out of port_info and into
ice_hw. Added the ability to offload SCTP checksum calculation to the
hardware. Added support for new PHY types, which support higher link
speeds.
Md Fahad makes sure that RSS lookup table and hash key get configured
during the rebuild path after a reset.
Brett updates the driver to set the physical link state according to the
netdev state (up/down). Added support for adaptive/dynamic interrupt
moderation in the ice driver, along with the ethtool operations needed.
Tony adds software timestamping support by using
ethtool_op_get_ts_info().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function ice_aq_manage_mac_write takes a pointer to a MAC address.
The parameter is not marked const, even though the function doesn't need
to modify it. This prevents passing a parameter that is already marked
const. Update the function prototype to take a const pointer, to allow
passing constant pointers to this function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds code for the detection and operation of several
additional PHY types that support higher link speeds.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds the ability to offload SCTP checksum calculations to the
NIC.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use ethtool_op_get_ts_info to provide software timestamping.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch includes the following ethtool operations:
1. get_coalesce
2. set_coalesce
3. get_per_q_coalesce
4. set_per_q_coalesce
Each ITR value (current_itr/target_itr) are stored on a per
ice_ring_container basis. This is because each valid ice_ring_container
can have 1 or more rings that are tied to the same q_vector ITR index.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently the driver does not support adaptive/dynamic interrupt
moderation. This patch adds support for this. Also, adaptive/dynamic
interrupt moderation is turned on by default upon driver load.
In order to support adaptive interrupt moderation, two functions were
added, ice_update_itr() and ice_itr_divisor(). These are used to
determine the current packet load and to determine a divisor based
on link speed respectively.
This patch also adds the ICE_ITR_GRAN_S define that is used in the
hot-path when setting a new ITR value. The shift is used to pet two
birds with one hand, set the ITR value while re-enabling the
interrupt. Also, the ICE_ITR_GRAN_S is defined as 1 because the device
has a ITR granularity of 2usecs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The aggregator list needs to be preserved for use after a reset. This
patch moves it out of the port_info instance and into the ice_hw instance.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch reworks the queue management code to allow for reuse with the
XDP feature (to be added in a future patch).
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add new infrastructure for implementing ethtool private flags using the
existing pf->flags bitmap to store them, and add the link-down-on-close
ethtool private flag to optionally bring down the PHY link when the
interface is administratively downed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When a netdev is set up/down we need to set the phsyical link state
accordingly. This patch adds that functionality by calling
ice_force_phys_link_state(vsi, link_up) in both the ice_stop() and
ice_open() paths.
In order to force link, ice_force_phys_link_state(vsi, link_up) will
first determine the current phy capabilities. If link has not changed
there is nothing to do. If link has changed, previous PHY capabilities
are saved and the "Enable Automatic Link Update" and "Link Establishment
State Machine (LESM)" enable bits are set. Then the new PHY config is
saved. The "Enable Automatic Link Update" will force the FW to execute
Setup link and restart auto-negotiation. This *should* then result in a
"Link Status Event (LSE)" which will cause the driver to get the current
link status.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add support for get_eeprom and get_eeprom_len ethtool ops
Specification states that PF software accesses NVM (shadow-ram) via AQ
commands (e.g. NVM Read, NVM Write) in the range 0x000000-0x00FFFF (64KB),
so the get_eeprom_len op should return 64KB. If additional regions of the
16MB NVM must be read, another access method must be used.
The ethtool kernel code, by default, will ask for multiple page-size hunks
of the NVM not to exceed the value returned by ice_get_eeprom_len().
ice_read_sr_buf() deals with arch page sizes different than 4KB.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add led blinking handler to ethtool. Since led blinking is
controlled by FW/HW only ETHTOOL_ID_ACTIVE and ETHTOOL_ID_INACTIVE
are really needed.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch configures the RSS lookup table and hash key post reset.
Signed-off-by: Md Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The following functions were refactored to call a new common function,
ice_aqc_send_sched_elem_cmd():
- ice_aq_add_sched_elems()
- ice_aq_delete_sched_elems()
- ice_aq_move_sched_elems()
- ice_aq_query_sched_elems()
- ice_aq_cfg_sched_elems()
- ice_aq_suspend_sched_elems()
- ice_aq_resume_sched_elems()
Signed-off-by: Greg Priest <greg.priest@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Pull networking fixes from David Miller:
1) Fix regression in multi-SKB responses to RTM_GETADDR, from Arthur
Gautier.
2) Fix ipv6 frag parsing in openvswitch, from Yi-Hung Wei.
3) Unbounded recursion in ipv4 and ipv6 GUE tunnels, from Stefano
Brivio.
4) Use after free in hns driver, from Yonglong Liu.
5) icmp6_send() needs to handle the case of NULL skb, from Eric
Dumazet.
6) Missing rcu read lock in __inet6_bind() when operating on mapped
addresses, from David Ahern.
7) Memory leak in tipc-nl_compat_publ_dump(), from Gustavo A. R. Silva.
8) Fix PHY vs r8169 module loading ordering issues, from Heiner
Kallweit.
9) Fix bridge vlan memory leak, from Ido Schimmel.
10) Dev refcount leak in AF_PACKET, from Jason Gunthorpe.
11) Infoleak in ipv6_local_error(), flow label isn't completely
initialized. From Eric Dumazet.
12) Handle mv88e6390 errata, from Andrew Lunn.
13) Making vhost/vsock CID hashing consistent, from Zha Bin.
14) Fix lack of UMH cleanup when it unexpectedly exits, from Taehee Yoo.
15) Bridge forwarding must clear skb->tstamp, from Paolo Abeni.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
bnxt_en: Fix context memory allocation.
bnxt_en: Fix ring checking logic on 57500 chips.
mISDN: hfcsusb: Use struct_size() in kzalloc()
net: clear skb->tstamp in bridge forwarding path
net: bpfilter: disallow to remove bpfilter module while being used
net: bpfilter: restart bpfilter_umh when error occurred
net: bpfilter: use cleanup callback to release umh_info
umh: add exit routine for UMH process
isdn: i4l: isdn_tty: Fix some concurrency double-free bugs
vhost/vsock: fix vhost vsock cid hashing inconsistent
net: stmmac: Prevent RX starvation in stmmac_napi_poll()
net: stmmac: Fix the logic of checking if RX Watchdog must be enabled
net: stmmac: Check if CBS is supported before configuring
net: stmmac: dwxgmac2: Only clear interrupts that are active
net: stmmac: Fix PCI module removal leak
tools/bpf: fix bpftool map dump with bitfields
tools/bpf: test btf bitfield with >=256 struct member offset
bpf: fix bpffs bitfield pretty print
net: ethernet: mediatek: fix warning in phy_start_aneg
tcp: change txhash on SYN-data timeout
...
|
|
Commit 2fd527b72bb6 ("net: ndo_bridge_setlink: Add extack") added a new
parameter "extack" to ice_bridge_setlink but this parameter isn't used
by the function. This results in a warning: unused parameter ‘extack’
[-Wunused-parameter]. Fix that by adding an "__always_unused" qualifier.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Pull GPIO fixes from Linus Walleij:
"The patch hitting the MMC/SD subsystem is fixing up my own mess when
moving semantics from MMC/SD over to gpiolib. Ulf is on vacation but I
managed to reach him on chat and obtain his ACK.
The other two are early-rc fixes that are not super serious but pretty
annoying so I'd like to get rid of them.
Summary:
- Get rid of some WARN_ON() from the ACPI code
- Staticize a symbol
- Fix MMC polarity detection"
* tag 'gpio-v5.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
mmc: core: don't override the CD GPIO level when "cd-inverted" is set
gpio: pca953x: Make symbol 'pca953x_i2c_regmap' static
gpiolib-acpi: Remove unnecessary WARN_ON from acpi_gpiochip_free_interrupts
|
|
Pull MFD updates from Lee Jones:
"New Device Support
- Add support for Power Supply to AXP813
- Add support for GPIO, ADC, AC and Battery Power Supply to AXP803
- Add support for UART to Exynos LPASS
Fix-ups:
- Use supplied MACROS; ti_am335x_tscadc
- Trivial spelling/whitespace/alignment; tmio, axp20x, rave-sp
- Regmap changes; bd9571mwv, wm5110-tables
- Kconfig dependencies; MFD_AT91_USART
- Supply shared data for child-devices; madera-core
- Use new of_node_name_eq() API call; max77620, stmpe
- Use managed resources (devm_*); tps65218
- Comment descriptions; ingenic-tcu
- Coding style; madera-core
Bug Fixes:
- Fix section mismatches; twl-core, db8500-prcmu
- Correct error path related issues; mt6397-core, ab8500-core, mc13xxx-core
- IRQ related fixes; tps6586x
- Ensure proper initialisation sequence; qcom_rpm
- Repair potential memory leak; cros_ec_dev"
* tag 'mfd-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (25 commits)
mfd: exynos-lpass: Enable UART module support
mfd: mc13xxx: Fix a missing check of a register-read failure
mfd: cros_ec: Add commands to control codec
mfd: madera: Remove spurious semicolon in while loop
mfd: rave-sp: Fix typo in rave_sp_checksum comment
mfd: ingenic-tcu: Fix bit field description in header
mfd: tps65218: Use devm_regmap_add_irq_chip and clean up error path in probe()
mfd: Use of_node_name_eq() for node name comparisons
mfd: cros_ec_dev: Add missing mfd_remove_devices() call in remove
mfd: axp20x: Add supported cells for AXP803
mfd: axp20x: Re-align MFD cell entries
mfd: axp20x: Add AC power supply cell for AXP813
mfd: wm5110: Add missing ASRC rate register
mfd: qcom_rpm: write fw_version to CTRL_REG
mfd: tps6586x: Handle interrupts on suspend
mfd: madera: Add shared data for accessory detection
mfd: at91-usart: Add platform dependency
mfd: bd9571mwv: Add volatile register to make DVFS work
mfd: ab8500-core: Return zero in get_register_interruptible()
mfd: tmio: Typo s/use use/use/
...
|
|
Pull backlight updates from Lee Jones:
"Fix-ups:
- Use new of_node_name_eq() API call
Bug Fixes:
- Internally track 'enabled' state in pwm_bl
- Fix auto-generated pwm_bl brightness tables parsed by DT
* tag 'backlight-next-4.21' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/backlight:
backlight: 88pm860x_bl: Use of_node_name_eq for node name comparisons
backlight: pwm_bl: Fix devicetree parsing with auto-generated brightness tables
backlight: pwm_bl: Re-add driver internal enabled tracking
|
|
Pull ARM SoC fixes from Olof Johansson:
"A bigger batch than I anticipated this week, for two reasons:
- Some fallout on Davinci from board file -> DTB conversion, that
also includes a few longer-standing fixes (i.e. not recent
regressions).
- drivers/reset material that has been in linux-next for a while, but
didn't get sent to us until now for a variety of reasons
(maintainer out sick, holidays, etc). There's a functional
dependency in there such that one platform (Altera's SoCFPGA) won't
boot without one of the patches; instead of reverting the patch
that got merged, I looked at this set and decided it was small
enough that I'll pick it up anyway. If you disagree I can revisit
with a smaller set.
That being said, there's also a handful of the usual stuff:
- Fix for a crash on Armada 7K/8K when the kernel touches
PSCI-reserved memory
- Fix for PCIe reset on Macchiatobin (Armada 8K development board,
what this email is sent from in fact :)
- Enable a few new-merged modules for Amlogic in arm64 defconfig
- Error path fixes on Integrator
- Build fix for Renesas and Qualcomm
- Initialization fix for Renesas RZ/G2E
.. plus a few more fixlets"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (28 commits)
ARM: integrator: impd1: use struct_size() in devm_kzalloc()
qcom-scm: Include <linux/err.h> header
gpio: pl061: handle failed allocations
ARM: dts: kirkwood: Fix polarity of GPIO fan lines
arm64: dts: marvell: mcbin: fix PCIe reset signal
arm64: dts: marvell: armada-ap806: reserve PSCI area
ARM: dts: da850-lcdk: Correct the sound card name
ARM: dts: da850-lcdk: Correct the audio codec regulators
ARM: dts: da850-evm: Correct the sound card name
ARM: dts: da850-evm: Correct the audio codec regulators
ARM: davinci: omapl138-hawk: fix label names in GPIO lookup entries
ARM: davinci: dm644x-evm: fix label names in GPIO lookup entries
ARM: davinci: dm355-evm: fix label names in GPIO lookup entries
ARM: davinci: da850-evm: fix label names in GPIO lookup entries
ARM: davinci: da830-evm: fix label names in GPIO lookup entries
arm64: defconfig: enable modules for amlogic s400 sound card
reset: uniphier-glue: Add AHCI reset control support in glue layer
dt-bindings: reset: uniphier: Add AHCI core reset description
reset: uniphier-usb3: Rename to reset-uniphier-glue
dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
...
|
|
Pull staging driver fixes from Greg KH:
"Here are some small staging driver fixes for some reported issues.
One reverts a patch that was made to the rtl8723bs driver that turned
out to not be needed at all as it was a bug in clang. The others fix
up some reported issues in the rtl8188eu driver and update the
MAINTAINERS file to point to Larry for this driver so he can get the
bug reports easier.
All have been in linux-next with no reported issues"
* tag 'staging-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
Revert "staging: rtl8723bs: Mark ACPI table declaration as used"
staging: rtl8188eu: Fix module loading from tasklet for WEP encryption
staging: rtl8188eu: Fix module loading from tasklet for CCMP encryption
MAINTAINERS: Add entry for staging driver r8188eu
|
|
Pull tty/serial fixes from Greg KH:
"Here are 2 tty and serial fixes for 5.0-rc2 that resolve some reported
issues.
The first is a simple serial driver fix for a regression that showed
up in 5.0-rc1. The second one resolves a number of reported issues
with the recent tty locking fixes that went into 5.0-rc1. Lots of
people have tested the second one and say it resolves their issues.
Both have been in linux-next with no reported issues"
* tag 'tty-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: Don't hold ldisc lock in tty_reopen() if ldisc present
serial: lantiq: Do not swap register read/writes
|
|
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes and quirk updates for 5.0-rc2.
The majority here are some quirks for some storage devices to get them
to work properly. There's also a fix here to resolve the reported
issues with some audio devices that say they are UAC3 compliant, but
really are not.
And a fix up for the MAINTAINERS file to remove a dead url.
All have been in linux-next with no reported issues"
* tag 'usb-5.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: storage: Remove outdated URL from MAINTAINERS
USB: Add USB_QUIRK_DELAY_CTRL_MSG quirk for Corsair K70 RGB
usbcore: Select only first configuration for non-UAC3 compliant devices
USB: storage: add quirk for SMI SM3350
USB: storage: don't insert sane sense for SPC3+ when bad sense specified
usb: cdc-acm: send ZLP for Telit 3G Intel based modems
|
|
Late reset controller changes for v5.0
This adds missing deassert functionality to the ARC HSDK reset driver,
fixes some indentation and grammar issues in the kernel docs, adds a
helper to count the number of resets on a device for the non-DT case
as well, adds an early reset driver for SoCFPGA and simple reset driver
support for Stratix10, and generalizes the uniphier USB3 glue layer
reset to also cover AHCI.
* tag 'reset-for-5.0-rc2' of git://git.pengutronix.de/git/pza/linux:
reset: uniphier-glue: Add AHCI reset control support in glue layer
dt-bindings: reset: uniphier: Add AHCI core reset description
reset: uniphier-usb3: Rename to reset-uniphier-glue
dt-bindings: reset: uniphier: Replace the expression of USB3 with generic peripherals
ARM: socfpga: dts: document "altr,stratix10-rst-mgr" binding
reset: socfpga: add an early reset driver for SoCFPGA
reset: fix null pointer dereference on dev by dev_name
reset: Add reset_control_get_count()
reset: Improve reset controller kernel docs
ARC: HSDK: improve reset driver
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Commit 49e54187ae0b ("ata: libahci_platform: comply to PHY framework") uses
the PHY_MODE_SATA, but that enum had not yet been added. This caused a
build failure for me, with today's linux.git.
Also, there is a potentially conflicting (mis-named) PHY_MODE_SATA, hiding
in the Marvell Berlin SATA PHY driver.
Fix the build by:
1) Renaming Marvell's defined value to a more scoped name,
in order to avoid any potential conflicts: PHY_BERLIN_MODE_SATA.
2) Adding the missing enum, which was going to be added anyway as part
of [1].
[1] https://lkml.kernel.org/r/20190108163124.6409-3-miquel.raynal@bootlin.com
Fixes: 49e54187ae0b ("ata: libahci_platform: comply to PHY framework")
Signed-off-by: John Hubbard <jhubbard@nvidia.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Grzegorz Jaszczyk <jaz@semihalf.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull block fixes from Jens Axboe:
- NVMe pull request from Christoph, with little fixes all over the map
- Loop caching fix for offset/bs change (Jaegeuk Kim)
- Block documentation tweaks (Jeff, Jon, Weiping, John)
- null_blk zoned tweak (John)
- ahch mvebu suspend/resume support. Should have gone into the merge
window, but there was some confusion on which tree had it. (Miquel)
* tag 'for-linus-20190112' of git://git.kernel.dk/linux-block: (22 commits)
ata: ahci: mvebu: request PHY suspend/resume for Armada 3700
ata: ahci: mvebu: add Armada 3700 initialization needed for S2RAM
ata: ahci: mvebu: do Armada 38x configuration only on relevant SoCs
ata: ahci: mvebu: remove stale comment
ata: libahci_platform: comply to PHY framework
loop: drop caches if offset or block_size are changed
block: fix kerneldoc comment for blk_attempt_plug_merge()
nvme: don't initlialize ctrl->cntlid twice
nvme: introduce NVME_QUIRK_IGNORE_DEV_SUBNQN
nvme: pad fake subsys NQN vid and ssvid with zeros
nvme-multipath: zero out ANA log buffer
nvme-fabrics: unset write/poll queues for discovery controllers
nvme-tcp: don't ask if controller is fabrics
nvme-tcp: remove dead code
nvme-pci: fix out of bounds access in nvme_cqe_pending
nvme-pci: rerun irq setup on IO queue init errors
nvme-pci: use the same attributes when freeing host_mem_desc_bufs.
nvme-pci: fix the wrong setting of nr_maps
block: doc: add slice_idle_us to bfq documentation
block: clarify documentation for blk_{start|finish}_plug
...
|
|
Pull dma_zalloc_coherent() removal from Christoph Hellwig:
"We've always had a weird situation around dma_zalloc_coherent. To
safely support mapping the allocations to userspace major
architectures like x86 and arm have always zeroed allocations from
dma_alloc_coherent, but a couple other architectures were missing that
zeroing either always or in corner cases.
Then later we grew anothe dma_zalloc_coherent interface to explicitly
request zeroing, but that just added __GFP_ZERO to the allocation
flags, which for some allocators that didn't end up using the page
allocator ended up being a no-op and still not zeroing the
allocations.
So for this merge window I fixed up all remaining architectures to
zero the memory in dma_alloc_coherent, and made dma_zalloc_coherent a
no-op wrapper around dma_alloc_coherent, which fixes all of the above
issues.
dma_zalloc_coherent is now pointless and can go away, and Luis helped
me writing a cocchinelle script and patch series to kill it, which I
think we should apply now just after -rc1 to finally settle these
issue"
* tag 'remove-dma_zalloc_coherent-5.0' of git://git.infradead.org/users/hch/dma-mapping:
dma-mapping: remove dma_zalloc_coherent()
cross-tree: phase out dma_zalloc_coherent() on headers
cross-tree: phase out dma_zalloc_coherent()
|
|
When allocating memory pages for context memory, if the last page table
should be fully populated, the current code will set nr_pages to 0 when
calling bnxt_alloc_ctx_mem_blk(). This will cause the last page table
to be completely blank and causing some RDMA failures.
Fix it by setting the last page table's nr_pages to the remainder only
if it is non-zero.
Fixes: 08fe9d181606 ("bnxt_en: Add Level 2 context memory paging support.")
Reported-by: Eric Davis <eric.davis@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_hwrm_check_pf_rings(), add the proper flag to test the NQ
resources. Without the proper flag, the firmware will change
the NQ resource allocation and remap the IRQ, causing missing
IRQs. This issue shows up when adding MQPRIO TX queues, for example.
Fixes: 36d65be9a880 ("bnxt_en: Disable MSIX before re-reserving NQs/CMPL rings.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull more drm fixes from Daniel Vetter:
"Dave sends out his pull, everybody remembers holidays are over :-)
Since Dave's already in weekend mode and it was quite a few patches I
figured better to apply all the pulls and forward them to you. Hence
here 2nd part of bugfixes for -rc2.
nouveau:
- backlight fix
- falcon register access fix
- fan fix.
i915:
- Disable PSR for Apple panels
- Broxton ERR_PTR error state fix
- Kabylake VECS workaround fix
- Unwind failure on pinning the gen7 ppgtt
- GVT workload request allocation fix
core:
- Fix fb-helper to work correctly with SDL 1.2 bugs
- Fix lockdep warning in the atomic ioctl and setproperty"
* tag 'drm-fixes-2019-01-11-1' of git://anongit.freedesktop.org/drm/drm:
drm/nouveau/falcon: avoid touching registers if engine is off
drm/nouveau: Don't disable polling in fallback mode
drm/nouveau: register backlight on pascal and newer
drm: Fix documentation generation for DP_DPCD_QUIRK_NO_PSR
drm/i915: init per-engine WAs for all engines
drm/i915: Unwind failure on pinning the gen7 ppgtt
drm/i915: Skip the ERR_PTR error state
drm/i915: Disable PSR in Apple panels
gpu/drm: Fix lock held when returning to user space.
drm/fb-helper: Ignore the value of fb_var_screeninfo.pixclock
drm/fb-helper: Partially bring back workaround for bugs of SDL 1.2
drm/i915/gvt: Fix workload request allocation before request add
|
|
One of the more common cases of allocation size calculations is finding the
size of a structure that has a zero-sized array at the end, along with memory
for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can now
use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The functions isdn_tty_tiocmset() and isdn_tty_set_termios() may be
concurrently executed.
isdn_tty_tiocmset
isdn_tty_modem_hup
line 719: kfree(info->dtmf_state);
line 721: kfree(info->silence_state);
line 723: kfree(info->adpcms);
line 725: kfree(info->adpcmr);
isdn_tty_set_termios
isdn_tty_modem_hup
line 719: kfree(info->dtmf_state);
line 721: kfree(info->silence_state);
line 723: kfree(info->adpcms);
line 725: kfree(info->adpcmr);
Thus, some concurrency double-free bugs may occur.
These possible bugs are found by a static tool written by myself and
my manual code review.
To fix these possible bugs, the mutex lock "modem_info_mutex" used in
isdn_tty_tiocmset() is added in isdn_tty_set_termios().
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The vsock core only supports 32bit CID, but the Virtio-vsock spec define
CID (dst_cid and src_cid) as u64 and the upper 32bits is reserved as
zero. This inconsistency causes one bug in vhost vsock driver. The
scenarios is:
0. A hash table (vhost_vsock_hash) is used to map an CID to a vsock
object. And hash_min() is used to compute the hash key. hash_min() is
defined as:
(sizeof(val) <= 4 ? hash_32(val, bits) : hash_long(val, bits)).
That means the hash algorithm has dependency on the size of macro
argument 'val'.
0. In function vhost_vsock_set_cid(), a 64bit CID is passed to
hash_min() to compute the hash key when inserting a vsock object into
the hash table.
0. In function vhost_vsock_get(), a 32bit CID is passed to hash_min()
to compute the hash key when looking up a vsock for an CID.
Because the different size of the CID, hash_min() returns different hash
key, thus fails to look up the vsock object for an CID.
To fix this bug, we keep CID as u64 in the IOCTLs and virtio message
headers, but explicitly convert u64 to u32 when deal with the hash table
and vsock core.
Fixes: 834e772c8db0 ("vhost/vsock: fix use-after-free in network stack callers")
Link: https://github.com/stefanha/virtio/blob/vsock/trunk/content.tex
Signed-off-by: Zha Bin <zhabin@linux.alibaba.com>
Reviewed-by: Liu Jiang <gerry@linux.alibaba.com>
Reviewed-by: Stefan Hajnoczi <stefanha@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, TX is given a budget which is consumed by stmmac_tx_clean()
and stmmac_rx() is given the remaining non-consumed budget.
This is wrong and in case we are sending a large number of packets this
can starve RX because remaining budget will be low.
Let's give always the same budget for RX and TX clean.
While at it, check if we missed any interrupts while we were in NAPI
callback by looking at DMA interrupt status.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX Watchdog can be disabled by platform definitions but currently we are
initializing the descriptors before checking if Watchdog must be
disabled or not.
Fix this by checking earlier if user wants Watchdog disabled or not.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check if CBS is currently supported before trying to configure it in HW.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In DMA interrupt handler we were clearing all interrupts status, even
the ones that were not active. Fix this and only clear the active
interrupts.
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit b7d0f08e9129, the enable / disable of PCI device is not
managed which will result in IO regions not being automatically unmapped.
As regions continue mapped it is currently not possible to remove and
then probe again the PCI module of stmmac.
Fix this by manually unmapping regions on remove callback.
Changes from v1:
- Fix build error
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Fixes: b7d0f08e9129 ("net: stmmac: Fix WoL for PCI-based setups")
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A feature has been added in the libahci driver: the possibility to set
a new flag in hpriv->flags to let the core handle PHY suspend/resume
automatically. Make use of this feature to make suspend to RAM work
with SATA drives on A3700.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
A3700 comphy initialization is done in the firmware (TF-A). Looking at
the SATA PHY initialization routine, there is a comment about "vendor
specific" registers. Two registers are mentioned. They are not
initialized there in the firmware because they are AHCI related, while
the firmware at this location does only PHY configuration. The
solution to avoid doing such initialization is relying on U-Boot.
While this work at boot time, U-Boot is definitely not going to run
during a resume after suspending to RAM.
Two possible solutions were considered:
* Fixing the firmware.
* Fixing the kernel driver.
The first solution would take ages to propagate, while the second
solution is easy to implement as the driver as been a little bit
reworked to prepare for such platform configuration. Hence, this patch
adds an Armada 3700 configuration function to set these two registers
both at boot time (in the probe) and after a suspend (in the resume
path).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
At the beginning, only Armada 38x SoCs where supported by the
ahci_mvebu.c driver. Commit 15d3ce7b63bd ("ata: ahci_mvebu: add
support for Armada 3700 variant") introduced Armada 3700 support. As
opposed to Armada 38x SoCs, the 3700 variants do not have to configure
mbus and the regret option. This patch took care of avoiding such
configuration when not needed in the probe function, but failed to do
the same in the resume path. While doing so looks harmless by
experience, let's clean the driver logic and avoid doing this useless
configuration with Armada 3700 SoCs.
Because the logic is very similar between these two places, it has
been decided to factorize this code and put it in a "Armada 38x
configuration function". This function is part of a new
(per-compatible) platform data structure, so that the addition of such
configuration function for Armada 3700 will be eased.
Fixes: 15d3ce7b63bd ("ata: ahci_mvebu: add support for Armada 3700 variant")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|