| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Some MediaTek platforms with a buggy TrustZone ATF firmware will not
initialize the AArch64 System Timer correctly: in these cases, the
System Timer address is correctly programmed, as well as the CNTFRQ_EL0
register (reading 13MHz, as it should be), but the assigned hardware
timers are never started before (or after) booting Linux.
In this condition, any call to function get_cycles() will be returning
zero, as CNTVCT_EL0 will always read zero.
One common critical symptom of that is trying to use the udelay()
function (calling __delay()), which executes the following loop:
start = get_cycles();
while ((get_cycles() - start) < cycles)
cpu_relax();
which, when CNTVCT_EL0 always reads zero, translates to:
while((0 - 0) < 0) ==> while(0 < 0)
... generating an infinite loop, even though zero is never less
than zero, but always equal to it (this has to be researched,
but it's out of the scope of this commit).
To fix this issue on the affected MediaTek platforms, the solution
is to simply start the timers that are designed to be System Timer(s).
These timers, downstream, are called "CPUXGPT" and there is one
timer per CPU core; luckily, it is not necessary to set a start bit
on each CPUX General Purpose Timer, but it's conveniently enough to:
- Set the clock divider (input = 26MHz, divider = 2, output = 13MHz);
- Set the ENABLE bit on a global register (starts all CPUX timers).
The only small hurdle with this setup is that it's all done through
the MCUSYS wrapper, where it is needed, for each read or write, to
select a register address (by writing it to an index register) and
then to perform any R/W on a "CON" register.
For example, writing "0x1" to the CPUXGPT register offset 0x4:
- Write 0x4 to mcusys INDEX register
- Write 0x1 to mcusys CON register
Reading from CPUXGPT register offset 0x4:
- Write 0x4 to mcusys INDEX register
- Read mcusys CON register.
Finally, starting this timer makes platforms affected by this issue
to work correctly.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20220613133819.35318-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
The timer IP block present on Tegra234 SoC supports watchdog timer
functionality that can be used to recover from system hangs. The
watchdog timer uses a timer in the background for countdown.
Signed-off-by: Kartik <kkartik@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1656922422-25823-4-git-send-email-kkartik@nvidia.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently this only supports a single watchdog, which uses a timer in
the background for countdown. Eventually the timers could be used for
various time-keeping tasks, but by default the architected timer will
already provide that functionality.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Kartik <kkartik@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/1656922422-25823-3-git-send-email-kkartik@nvidia.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Use the possessive "its" instead of the contraction "it's"
where appropriate.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Link: https://lore.kernel.org/r/20220715015852.12523-1-rdunlap@infradead.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Fault inject on pool metadata device reports:
BUG: KASAN: use-after-free in dm_pool_register_metadata_threshold+0x40/0x80
Read of size 8 at addr ffff8881b9d50068 by task dmsetup/950
CPU: 7 PID: 950 Comm: dmsetup Tainted: G W 5.19.0-rc6 #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.14.0-1.fc33 04/01/2014
Call Trace:
<TASK>
dump_stack_lvl+0x34/0x44
print_address_description.constprop.0.cold+0xeb/0x3f4
kasan_report.cold+0xe6/0x147
dm_pool_register_metadata_threshold+0x40/0x80
pool_ctr+0xa0a/0x1150
dm_table_add_target+0x2c8/0x640
table_load+0x1fd/0x430
ctl_ioctl+0x2c4/0x5a0
dm_ctl_ioctl+0xa/0x10
__x64_sys_ioctl+0xb3/0xd0
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x46/0xb0
This can be easily reproduced using:
echo offline > /sys/block/sda/device/state
dd if=/dev/zero of=/dev/mapper/thin bs=4k count=10
dmsetup load pool --table "0 20971520 thin-pool /dev/sda /dev/sdb 128 0 0"
If a metadata commit fails, the transaction will be aborted and the
metadata space maps will be destroyed. If a DM table reload then
happens for this failed thin-pool, a use-after-free will occur in
dm_sm_register_threshold_callback (called from
dm_pool_register_metadata_threshold).
Fix this by in dm_pool_register_metadata_threshold() by returning the
-EINVAL error if the thin-pool is in fail mode. Also fail pool_ctr()
with a new error message: "Error registering metadata threshold".
Fixes: ac8c3f3df65e4 ("dm thin: generate event when metadata threshold passed")
Cc: stable@vger.kernel.org
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Luo Meng <luomeng12@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@kernel.org>
|
|
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224750.172301548@goodmis.org
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224749.991587733@goodmis.org
Cc: Peter Chen <peter.chen@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224749.806599472@goodmis.org
Cc: Gregory Greenman <gregory.greenman@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224749.622796175@goodmis.org
Cc: Arend van Spriel <aspriel@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Franky Lin <franky.lin@broadcom.com>
Cc: Hante Meuleman <hante.meuleman@broadcom.com>
Cc: Kalle Valo <kvalo@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: linux-wireless@vger.kernel.org
Cc: brcm80211-dev-list.pdl@broadcom.com
Cc: SHA-cyfmac-dev-list@infineon.com
Cc: netdev@vger.kernel.org
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224749.430339634@goodmis.org
Cc: Kalle Valo <kvalo@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: ath11k@lists.infradead.org
Acked-by: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
Instead of open coding a __dynamic_array() with a fixed length (which
defeats the purpose of the dynamic array in the first place). Use the new
__vstring() helper that will use a va_list and only write enough of the
string into the ring buffer that is needed.
Link: https://lkml.kernel.org/r/20220705224749.239494531@goodmis.org
Cc: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
|
|
IPQ60xx series of SoCs have one port of PCIe gen 3. Add support for that
platform.
The code is based on downstream[1] Codeaurora kernel v5.4 (branch
win.linuxopenwrt.2.0).
Split out the DBI registers access part from .init into .post_init. DBI
registers are only accessible after phy_power_on().
[1] https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-ipq-5.4/
Link: https://lore.kernel.org/r/f7f848653c99abbf9a0f877949a44e52329543ae.1655799816.git.baruch@tkos.co.il
Tested-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Selvam Sathappan Periakaruppan <quic_speriaka@quicinc.com>
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
The PCIE_CAP_LINK1_VAL macro actually defines slot capabilities. Use
PCI_EXP_SLTCAP_* macros to spell its value, and rename it to better
describe its meaning.
Link: https://lore.kernel.org/r/3025d5e1d8da64798db6958f9780c4763fbcac47.1655799816.git.baruch@tkos.co.il
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
These are common dwc macros that will be used for other platforms.
Link: https://lore.kernel.org/r/1c2d5a7a139be81fa15f356b2380163dbdebdc09.1655799816.git.baruch@tkos.co.il
Signed-off-by: Baruch Siach <baruch.siach@siklu.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
|
Manual reparenting of pipe_clk_src is being replaced with the parking of
the clock with clk_disable()/clk_enable() in the PHY driver. Drop
redundant code switching of the pipe clock between the PHY clock source
and the safe bi_tcxo.
Link: https://lore.kernel.org/r/20220608105238.2973600-6-dmitry.baryshkov@linaro.org
Tested-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
clang static analysis reports
drivers/gpu/drm/nouveau/nvkm/subdev/bios/pmu.c:68:17: warning: The right operand of '*' is a garbage value [core.UndefinedBinaryOperatorResult]
switch (!!data * *ver) {
^ ~~~~
A switch statement with only a default should be reduced to an if.
If nvbios_pmuEp() returns 0, via the data variable, the output info parameter
is not used. So set info only when data is not 0.
The struct nvbios_pmuE only has the type and data elements. Since both of these
are explicitly set, memset is not needed. So remove it.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220702153904.1696595-1-trix@redhat.com
|
|
The Dell Inspiron N4010 does not have ACPI backlight control,
so acpi_video_get_backlight_type()'s heuristics return vendor as
the type to use.
But the vendor interface is broken, where as the native (intel_backlight)
works well, add a quirk to use native.
Link: https://lore.kernel.org/regressions/CALF=6jEe5G8+r1Wo0vvz4GjNQQhdkLT5p8uCHn6ZXhg4nsOWow@mail.gmail.com/
Reported-and-tested-by: Ben Greening <bgreening@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
If the PNP0D80 device is present and its _DSM appears to be valid,
there is no reason to avoid using it even if ACPI_FADT_LOW_POWER_S0
is unset in the FADT, because suspend-to-idle may be the only way to
suspend the system if S3 is not supported by the platform, so do not
return early from lps0_device_attach() in that case.
However, still check ACPI_FADT_LOW_POWER_S0 when deciding whether or
not suspend-to-idle should be the default system suspend method.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
|
|
Revert commit 1cdda9486f51 ("ACPI / PM: LPIT: Register sysfs attributes
based on FADT"), because what it did was more confusing than it would
be to allow the sysfs attributes in question to be created regardless
of whether or not the relevant flag was set in the FADT.
If ACPI_FADT_LOW_POWER_S0 is not set, it need not mean that LPIT is
invalid and low-power S0 idle is not usable. It merely means that
using S3 on the given system is more beneficial from the energy
saving perspective than using low-power S0 idle.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Mario Limonciello <mario.limonciello@amd.com>
|
|
This driver is currently broken, it does not show the in0_input sysfs
file and also returns the following message on startup:
hwmon_device_register() is deprecated. Please convert the driver to
use hwmon_device_register_with_info().
This patch converts the driver and also cleans up the 'read' function.
Signed-off-by: Marc Ferland <ferlandm@amotus.ca>
Link: https://lore.kernel.org/r/20220712193504.1374656-1-ferlandm@amotus.ca
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
After commit 62b36c3ea664 ("PCI/AER: Remove
pci_cleanup_aer_uncorrect_error_status() calls"), calls to
pci_cleanup_aer_uncorrect_error_status() have already been removed. But in
commit 5995b6d0c6fc ("ice: Implement pci_error_handler ops")
pci_cleanup_aer_uncorrect_error_status was used again, so remove it in
this patch.
Signed-off-by: Zhuo Chen <chenzhuo.1@bytedance.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Sen Wang <wangsen.harry@bytedance.com>
Cc: Wenliang Wang <wangwenliang.1995@bytedance.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
External time stamp sources are supported only on certain devices. Enforce
the right support matrix by adding the ICE_F_PTP_EXTTS bit to the feature
bitmap set.
Co-developed-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Pull spi fixes from Mark Brown:
"A few driver specific fixes, none especially remarkable, plus a
MAINTAINERS file update due to the previous maintainer for the NXP
FSPI driver having left the company"
* tag 'spi-fix-v5.19-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: cadence-quadspi: Remove spi_master_put() in probe failure path
MAINTAINERS: change the NXP FSPI driver maintainer.
spi: amd: Limit max transfer and message size
spi: aspeed: Fix division by zero
spi: aspeed: Add dev_dbg() to dump the spi-mem direct mapping descriptor
|
|
With the new design in place, the show() and store() callbacks check if
the policy is active or not before proceeding any further to avoid
potential races. And in order to guarantee that cpufreq_policy_free()
must be called after clearing the policy->cpus mask, i.e. by marking the
policy inactive.
In order to avoid introducing a bug around this later, print a warning
message if we end up freeing an active policy.
Also update cpufreq_online() a bit to make sure we clear the cpus mask
for each error case before calling cpufreq_policy_free().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The SCMI v3.1 adds support for power values in micro-Watts. They are not
always in milli-Watts anymore (ignoring the bogo-Watts). Thus, the power
must be converted conditionally before sending to Energy Model. Add the
logic which handles the needed checks and conversions.
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In SCMI v3.1 the power scale can be in micro-Watts. The upper layers, e.g.
cpufreq and EM should handle received power values properly (upscale when
needed). Thus, provide an interface which allows to check what is the
scale for power values. The old interface allowed to distinguish between
bogo-Watts and milli-Watts only (which was good for older SCMI spec).
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The milli-Watts precision causes rounding errors while calculating
efficiency cost for each OPP. This is especially visible in the 'simple'
Energy Model (EM), where the power for each OPP is provided from OPP
framework. This can cause some OPPs to be marked inefficient, while
using micro-Watts precision that might not happen.
Update all EM users which access 'power' field and assume the value is
in milli-Watts.
Solve also an issue with potential overflow in calculation of energy
estimation on 32bit machine. It's needed now since the power value
(thus the 'cost' as well) are higher.
Example calculation which shows the rounding error and impact:
power = 'dyn-power-coeff' * volt_mV * volt_mV * freq_MHz
power_a_uW = (100 * 600mW * 600mW * 500MHz) / 10^6 = 18000
power_a_mW = (100 * 600mW * 600mW * 500MHz) / 10^9 = 18
power_b_uW = (100 * 605mW * 605mW * 600MHz) / 10^6 = 21961
power_b_mW = (100 * 605mW * 605mW * 600MHz) / 10^9 = 21
max_freq = 2000MHz
cost_a_mW = 18 * 2000MHz/500MHz = 72
cost_a_uW = 18000 * 2000MHz/500MHz = 72000
cost_b_mW = 21 * 2000MHz/600MHz = 70 // <- artificially better
cost_b_uW = 21961 * 2000MHz/600MHz = 73203
The 'cost_b_mW' (which is based on old milli-Watts) is misleadingly
better that the 'cost_b_uW' (this patch uses micro-Watts) and such
would have impact on the 'inefficient OPPs' information in the Cpufreq
framework. This patch set removes the rounding issue.
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Pull ARM SoC fixes from Arnd Bergmann:
"Most of the contents are bugfixes for the devicetree files:
- A Qualcomm MSM8974 pin controller regression, caused by a cleanup
patch that gets partially reverted here.
- Missing properties for Broadcom BCM49xx to fix timer detection and
SMP boot.
- Fix touchscreen pinctrl for imx6ull-colibri board
- Multiple fixes for Rockchip rk3399 based machines including the vdu
clock-rate fix, otg port fix on Quartz64-A and ethernet on
Quartz64-B
- Fixes for misspelled DT contents causing minor problems on
imx6qdl-ts7970m, orangepi-zero, sama5d2, kontron-kswitch-d10, and
ls1028a
And a couple of changes elsewhere:
- Fix binding for Allwinner D1 display pipeline
- Trivial code fixes to the TEE and reset controller driver
subsystems and the rockchip platform code.
- Multiple updates to the MAINTAINERS files, marking the Palm Treo
support as orphaned, and fixing some entries for added or changed
file names"
* tag 'soc-fixes-5.19-3' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (21 commits)
arm64: dts: broadcom: bcm4908: Fix cpu node for smp boot
arm64: dts: broadcom: bcm4908: Fix timer node for BCM4906 SoC
ARM: dts: sunxi: Fix SPI NOR campatible on Orange Pi Zero
ARM: dts: at91: sama5d2: Fix typo in i2s1 node
tee: tee_get_drvdata(): fix description of return value
optee: Remove duplicate 'of' in two places.
ARM: dts: kswitch-d10: use open drain mode for coma-mode pins
ARM: dts: colibri-imx6ull: fix snvs pinmux group
optee: smc_abi.c: fix wrong pointer passed to IS_ERR/PTR_ERR()
MAINTAINERS: add polarfire rng, pci and clock drivers
MAINTAINERS: mark ARM/PALM TREO SUPPORT orphan
ARM: dts: imx6qdl-ts7970: Fix ngpio typo and count
arm64: dts: ls1028a: Update SFP node to include clock
dt-bindings: display: sun4i: Fix D1 pipeline count
ARM: dts: qcom: msm8974: re-add missing pinctrl
reset: Fix devm bulk optional exclusive control getter
MAINTAINERS: rectify entry for SYNOPSYS AXS10x RESET CONTROLLER DRIVER
ARM: rockchip: Add missing of_node_put() in rockchip_suspend_init()
arm64: dts: rockchip: Assign RK3399 VDU clock rate
arm64: dts: rockchip: Fix Quartz64-A dwc3 otg port behavior
...
|
|
Pull x86 platform driver fixes from Hans de Goede:
"Highlights:
- Fix brightness key events getting reported twice on some Dells.
Regression caused by recent Panasonic hotkey fixes
- Fix poweroff no longer working on some devices regression caused
by recent poweroff handler rework
- Mark new (in 5.19) Intel IFS driver as broken, because of some
issues surrounding the userspace (sysfs) API which need to be
cleared up
- Some hardware-id / quirk additions"
* tag 'platform-drivers-x86-v5.19-4' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
ACPI: video: Fix acpi_video_handles_brightness_key_presses()
platform/x86: intel_atomisp2_led: Also turn off the always-on camera LED on the Asus T100TAF
platform/x86/intel/ifs: Mark as BROKEN
platform/x86: asus-wmi: Add key mappings
efi: Fix efi_power_off() not being run before acpi_power_off() when necessary
platform/x86: x86-android-tablets: Fix Lenovo Yoga Tablet 2 830/1050 poweroff again
platform/x86: gigabyte-wmi: add support for B660I AORUS PRO DDR4
platform/x86/amd/pmc: Add new platform support
platform/x86/amd/pmc: Add new acpi id for PMC controller
|
|
Pull xen fix from Juergen Gross:
"Fix for the Xen gntdev driver causing inappropriate WARN() messages"
* tag 'for-linus-5.19a-rc7-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/gntdev: Ignore failure to unmap INVALID_GRANT_HANDLE
|
|
Pull drm fixes from Dave Airlie:
"This is the regular fixes pull for this week. This has a bunch of
amdgpu fixes, major one reverts the buddy allocator until it can be
tested more, otherwise just small ones, then i915 has a bunch of
fixes.
The outstanding firmware regressions reported by phoronix will
hopefully be dealt with ASAP.
amdgpu:
- revert buddy allocator support for now
- DP MST blank screen fix for specific platforms
- MEC firmware check fix for GC 10.3.7
- Deep color fix for DCE
- Fix possible divide by 0
- Coverage blend mode fix
- Fix cursor only commit timestamps
i915:
- Selftest fix
- TTM fix sg_table construction
- Error return fixes
- Fix a performance regression related to waitboost
- Fix GT resets"
* tag 'drm-fixes-2022-07-15' of git://anongit.freedesktop.org/drm/drm:
drm/amd/display: Ensure valid event timestamp for cursor-only commits
drm/amd/display: correct check of coverage blend mode
drm/amd/pm: Prevent divide by zero
drm/amd/display: Only use depth 36 bpp linebuffers on DCN display engines.
drm/amdkfd: correct the MEC atomic support firmware checking for GC 10.3.7
drm/amd/display: Ignore First MST Sideband Message Return Error
drm/i915/selftests: fix subtraction overflow bug
drm/i915/gem: Look for waitboosting across the whole object prior to individual waits
drm/i915/gt: Serialize TLB invalidates with GT resets
drm/i915/gt: Serialize GRDOM access between multiple engine resets
drm/i915/ttm: fix sg_table construction
drm/i915/selftests: fix a couple IS_ERR() vs NULL tests
drm/i915: Fix vm use-after-free in vma destruction
drm/i915/guc: ADL-N should use the same GuC FW as ADL-S
drm/i915: fix a possible refcount leak in intel_dp_add_mst_connector()
drm/i915/gvt: IS_ERR() vs NULL bug in intel_gvt_update_reg_whitelist()
Revert "drm/amdgpu: add drm buddy support to amdgpu"
|
|
'F.7.3.6.1 General slice segment header syntax' section of HEVC
specification describes that a slice header always end aligned on
byte boundary, therefore we only need to provide the data offset in bytes.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Fix padding where needed to remove holes
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The number of bits to skip in the slice header can be computed
in the driver by using sps, pps and decode_params information.
This makes it possible to remove Hantro dedicated control.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Simply print the type of the control.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The number of 'entry point offset' can be very variable.
Instead of using a large static array define a v4l2 dynamic array
of U32 (V4L2_CTRL_TYPE_U32).
The number of entry point offsets is reported by the elems field
and in struct v4l2_ctrl_hevc_slice_params.num_entry_point_offsets
field.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
06781a5026350 Fixes the calculation of the DEVICE_BUSY_TIMEOUT register
value from busy_timeout_cycles. busy_timeout_cycles is calculated wrong
though: It is calculated based on the maximum page read time, but the
timeout is also used for page write and block erase operations which
require orders of magnitude bigger timeouts.
Fix this by calculating busy_timeout_cycles from the maximum of
tBERS_max and tPROG_max.
This is for now the easiest and most obvious way to fix the driver.
There's room for improvements though: The NAND_OP_WAITRDY_INSTR tells us
the desired timeout for the current operation, so we could program the
timeout dynamically for each operation instead of setting a fixed
timeout. Also we could wire up the interrupt handler to actually detect
and forward timeouts occurred when waiting for the chip being ready.
As a sidenote I verified that the change in 06781a5026350 is really
correct. I wired up the interrupt handler in my tree and measured the
time between starting the operation and the timeout interrupt handler
coming in. The time increases 41us with each step in the timeout
register which corresponds to 4096 clock cycles with the 99MHz clock
that I have.
Fixes: 06781a5026350 ("mtd: rawnand: gpmi: Fix setting busy timeout setting")
Fixes: b1206122069aa ("mtd: rawniand: gpmi: use core timings instead of an empirical derivation")
Cc: stable@vger.kernel.org
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Han Xu <han.xu@nxp.com>
Tested-by: Tomasz Moń <tomasz.mon@camlingroup.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Using bin_attributes with a 0 size causes fstat and friends to return that
0 size. This breaks userspace code that retrieves the size before reading
the file. Rather than reverting 75bd50fa841 ("drivers/base/node.c: use
bin_attribute to break the size limitation of cpumap ABI") let's put in a
size value at compile time.
For cpulist the maximum size is on the order of
NR_CPUS * (ceil(log10(NR_CPUS)) + 1)/2
which for 8192 is 20480 (8192 * 5)/2. In order to get near that you'd need
a system with every other CPU on one node. For example: (0,2,4,8, ... ).
To simplify the math and support larger NR_CPUS in the future we are using
(NR_CPUS * 7)/2. We also set it to a min of PAGE_SIZE to retain the older
behavior for smaller NR_CPUS.
The cpumap file the size works out to be NR_CPUS/4 + NR_CPUS/32 - 1
(or NR_CPUS * 9/32 - 1) including the ","s.
Add a set of macros for these values to cpumask.h so they can be used in
multiple places. Apply these to the handful of such files in
drivers/base/topology.c as well as node.c.
As an example, on an 80 cpu 4-node system (NR_CPUS == 8192):
before:
-r--r--r--. 1 root root 0 Jul 12 14:08 system/node/node0/cpulist
-r--r--r--. 1 root root 0 Jul 11 17:25 system/node/node0/cpumap
after:
-r--r--r--. 1 root root 28672 Jul 13 11:32 system/node/node0/cpulist
-r--r--r--. 1 root root 4096 Jul 13 11:31 system/node/node0/cpumap
CONFIG_NR_CPUS = 16384
-r--r--r--. 1 root root 57344 Jul 13 14:03 system/node/node0/cpulist
-r--r--r--. 1 root root 4607 Jul 13 14:02 system/node/node0/cpumap
The actual number of cpus doesn't matter for the reported size since they
are based on NR_CPUS.
Fixes: 75bd50fa841d ("drivers/base/node.c: use bin_attribute to break the size limitation of cpumap ABI")
Fixes: bb9ec13d156e ("topology: use bin_attribute to break the size limitation of cpumap ABI")
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Rafael J. Wysocki" <rafael@kernel.org>
Cc: Yury Norov <yury.norov@gmail.com>
Cc: stable@vger.kernel.org
Acked-by: Yury Norov <yury.norov@gmail.com> (for include/linux/cpumask.h)
Signed-off-by: Phil Auld <pauld@redhat.com>
Link: https://lore.kernel.org/r/20220715134924.3466194-1-pauld@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make explicit that V4L2_CID_STATELESS_HEVC_SLICE_PARAMS control is
a dynamic array control type.
Some drivers may be able to receive multiple slices in one control
to improve decoding performance.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
The HEVC specification describes the following:
"PicOrderCntVal is derived as follows:
PicOrderCntVal = PicOrderCntMsb + slice_pic_order_cnt_lsb
The value of PicOrderCntVal shall be in the range of
−2^31 to 2^31 − 1, inclusive."
To match with these definitions change __u16 pic_order_cnt[2]
into __s32 pic_order_cnt_val.
Change v4l2_ctrl_hevc_slice_params->slice_pic_order_cnt to __s32 too.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Change HEVC stateless controls names to V4L2_CID_STATELESS_HEVC instead
of V4L2_CID_MPEG_VIDEO_HEVC be coherent with v4l2 naming convention.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Reviewed-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add a dynamic array test control to help test support for this
feature.
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Implement support for dynamically allocated arrays.
Most of the changes concern keeping track of the number of elements
of the array and the number of elements allocated for the array and
reallocating memory if needed.
Acked-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Acked-by: Nicolas Dufresne <nicolas.dufresne@collabora.com>
Tested-by: Benjamin Gaignard <benjamin.gaignard@collabora.com>
Tested-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
This patch set is to support bucket in icc-rpm driver, so it implements
the similar mechanism in the icc-rpmh driver.
It uses interconnect path tag to indicate the bandwidth voting is for
which buckets, and there have three kinds of buckets: AWC, WAKE and
SLEEP, finally the wake and sleep bucket values are used to set the
corresponding clock (active and sleep clocks). So far, we keep the AWC
bucket but doesn't really use it.
Link: https://lore.kernel.org/r/20220712015929.2789881-1-leo.yan@linaro.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
This patchset is to support i.MX8MP NoC settings, i.MX8MP NoC initial
value after power up is invalid, need set a valid value after related
power domain up.
This patchset also includes two patch[1,2] during my development to enable
the ICC feature for i.MX8MP.
I not include ddrc DVFS in this patchset, ths patchset is only to
support NoC value mode/priority/ext_control being set to a valid value
that suggested by i.MX Chip Design Team. The value is same as NXP
downstream one inside Arm Trusted Firmware:
https://source.codeaurora.org/external/imx/imx-atf/tree/plat/imx/imx8m/i/gpc.c?h=lf_v2.4#n97
Link: https://lore.kernel.org/r/20220703091132.1412063-1-peng.fan@oss.nxp.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Same to i.MX8MM/N/Q, register i.MX8MP interconnect device to make
i.MX8MP Interconnect driver work.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20220703091132.1412063-10-peng.fan@oss.nxp.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Add a platform driver for the i.MX8MP SoC describing bus topology, based
on internal documentation.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220703091132.1412063-9-peng.fan@oss.nxp.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Introduce imx_icc_noc_setting structure to describe a master port setting
Pass imx_icc_noc_setting as a parameter from specific driver
Set priority level, mode, ext control in imx_icc_node_set
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220703091132.1412063-8-peng.fan@oss.nxp.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
Introduce imx_icc_provider as a wrapper of icc_provider to
add i.MX specific information.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220703091132.1412063-7-peng.fan@oss.nxp.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
When set QoS for a icc path, only set dst icc node is not enough,
also need to set src icc node.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20220703091132.1412063-6-peng.fan@oss.nxp.com
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
AngeloGioacchino Del Regno
Kartik
Thierry Reding
Randy Dunlap
Luo Meng
Steven Rostedt (Google)
Selvam Sathappan Periakaruppan
Baruch Siach
Dmitry Baryshkov
Tom Rix
Hans de Goede
Rafael J. Wysocki
Marc Ferland
Zhuo Chen
Anirudh Venkataramanan
Linus Torvalds
Viresh Kumar
Lukasz Luba
Benjamin Gaignard
Sascha Hauer
Phil Auld
Hans Verkuil
Georgi Djakov
Peng Fan