| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If available in firmware, find resources by their 'reg-names' position
instead of relying on hardcoded offsets. Care is taken to support old
firmware nonetheless.
Signed-off-by: Nicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20220625113619.15944-7-stefan.wahren@i2se.com
|
|
Unify and move compile-time known information into new struct
kvaser_usb_driver_info, in favor of run-time checks.
All Kvaser USBcanII supports listen-only mode and error counter
reporting.
Link: https://lore.kernel.org/all/20220603083820.800246-2-extja@kvaser.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: stable@vger.kernel.org
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
[mkl: move struct kvaser_usb_driver_info into kvaser_usb_core.c]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix spelling of 'waitting' in comments.
remove unnecessary space of 'MDIO_COMMAND_REG 's'.
Signed-off-by: Zhang Jiaming <jiaming@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a reset, there may have been transmits in flight that are no
longer valid and cannot be fulfilled. Resetting and clearing the
queues is insufficient; each skb also needs to be explicitly freed
so that upper levels are not left waiting for confirmation of a
transmit that will never happen. If this happens frequently enough,
the apparent backlog will cause TCP to begin "congestion control"
unnecessarily, culminating in permanently decreased throughput.
Fixes: d7c0ef36bde03 ("ibmvnic: Free and re-allocate scrqs when tx/rx scrqs change")
Tested-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Rick Lindsley <ricklind@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for TX VLAN ctag insert
which may be configured via ethtool.
e.g.
# ethtool -K $DEV tx-vlan-offload on
The NIC supplies VLAN insert information as packet metadata.
The fields of this VLAN metadata are gotten from sk_buff, including
vlan_proto and vlan tag.
Configuration control bit NFP_NET_CFG_CTRL_TXVLAN_V2 is to
signal availability of ctag-insert features of the firmware.
NFDK is used to communicate via PCIE to NFP-3800 based NICs
while NFD3 is used for other NICs supported by the NFP driver.
The metadata format on tx side of NFD3 is different from NFDK.
This feature is not currently implemented for NFDK.
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for RX VLAN ctag/stag strip
which may be configured via ethtool.
e.g.
# ethtool -K $DEV rx-vlan-offload on
# ethtool -K $DEV rx-vlan-stag-hw-parse on
Ctag-stripped and stag-stripped cannot be enabled at the same time
because currently the kernel supports only one layer of VLAN stripping.
The NIC supplies VLAN strip information as packet metadata.
The fields of this VLAN metadata are:
* strip flag: 1 for stripped; 0 for unstripped
* tci: VLAN TCI ID
* tpid: 1 for ETH_P_8021AD; 0 for ETH_P_8021Q
Configuration control bits NFP_NET_CFG_CTRL_RXVLAN_V2 and
NFP_NET_CFG_CTRL_RXQINQ are to signal availability of
ctag-strip and stag-strip features of the firmware.
Signed-off-by: Diana Wang <na.wang@corigine.com>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 1be37d3b0414 ("can: m_can: fix periph RX path: use
rx-offload to ensure skbs are sent from softirq context") the RX path
for peripheral devices was switched to RX-offload.
Received CAN frames are pushed to RX-offload together with a
timestamp. RX-offload is designed to handle overflows of the timestamp
correctly, if 32 bit timestamps are provided.
The timestamps of m_can core are only 16 bits wide. So this patch
shifts them to full 32 bit before passing them to RX-offload.
Link: https://lore.kernel.org/all/20220612211410.4081390-1-mkl@pengutronix.de
Fixes: 1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In commit df06fd678260 ("can: m_can: m_can_chip_config(): enable and
configure internal timestamps") the timestamping in the m_can core
should be enabled. In peripheral mode, the RX'ed CAN frames, TX
compete frames and error events are sorted by the timestamp.
The above mentioned commit however forgot to enable the timestamping.
Add the missing bits to enable the timestamp counter to the write of
the Timestamp Counter Configuration register.
Link: https://lore.kernel.org/all/20220612212708.4081756-1-mkl@pengutronix.de
Fixes: df06fd678260 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Cc: <stable@vger.kernel.org> # 5.13
Cc: Torin Cooper-Bennun <torin@maxiluxsystems.com>
Reviewed-by: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In grcan_probe(), of_find_node_by_path() has already increased the
refcount. There is no need to call of_node_get() again, so remove it.
Link: https://lore.kernel.org/all/20220619070257.4067022-1-windhl@126.com
Fixes: 1e93ed26acf0 ("can: grcan: grcan_probe(): fix broken system id check for errata workaround needs")
Cc: stable@vger.kernel.org # v5.18
Cc: Andreas Larsson <andreas@gaisler.com>
Signed-off-by: Liang He <windhl@126.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The gs_usb driver appears to suffer from a malady common to many USB
CAN adapter drivers in that it performs usb_alloc_coherent() to
allocate a number of USB request blocks (URBs) for RX, and then later
relies on usb_kill_anchored_urbs() to free them, but this doesn't
actually free them. As a result, this may be leaking DMA memory that's
been used by the driver.
This commit is an adaptation of the techniques found in the esd_usb2
driver where a similar design pattern led to a memory leak. It
explicitly frees the RX URBs and their DMA memory via a call to
usb_free_coherent(). Since the RX URBs were allocated in the
gs_can_open(), we remove them in gs_can_close() rather than in the
disconnect function as was done in esd_usb2.
For more information, see the 928150fad41b ("can: esd_usb2: fix memory
leak").
Link: https://lore.kernel.org/all/alpine.DEB.2.22.394.2206031547001.1630869@thelappy
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: stable@vger.kernel.org
Signed-off-by: Rhett Aultman <rhett.aultman@samsara.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
On R-Car V3U, this driver should use suitable register offset instead of
other SoCs' one. Otherwise, data transmission failed on R-Car V3U.
Fixes: 45721c406dcf ("can: rcar_canfd: Add support for r8a779a0 SoC")
Link: https://lore.kernel.org/all/20220704074611.957191-1-yoshihiro.shimoda.uh@renesas.com
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Duy Nguyen <duy.nguyen.rh@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
smsc95xx_read_reg() and smsc95xx_write_reg() call BUG_ON() if the
struct usbnet pointer passed in is NULL.
The functions have just been amended to dereference the pointer on
entry. So the kernel now oopses if the pointer is NULL, eliminating
the need for an explicit BUG_ON().
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN95xx driver has just been amended to auto-detect whether the
_nopm variant of usbnet_read_cmd() / usbnet_write_cmd() shall be used.
Drop all the now unnecessary open coding of that distinction.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 05b35e7eb9a1 ("smsc95xx: add phylib support") amended
smsc95xx_resume() to call phy_init_hw(). That function waits for the
device to runtime resume even though it is placed in the runtime resume
path, causing a deadlock.
The problem is that phy_init_hw() calls down to smsc95xx_mdiobus_read(),
which never uses the _nopm variant of usbnet_read_cmd().
Commit b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with
reset operation") causes a similar deadlock on resume if the device was
already runtime suspended when entering system sleep:
That's because the commit introduced smsc95xx_reset_resume(), which
calls down to smsc95xx_reset(), which neglects to use _nopm accessors.
Fix by auto-detecting whether a device access is performed by the
suspend/resume task_struct and use the _nopm variant if so. This works
because the PM core guarantees that suspend/resume callbacks are run in
task context.
Stacktrace for posterity:
INFO: task kworker/2:1:49 blocked for more than 122 seconds.
Workqueue: usb_hub_wq hub_event
schedule
rpm_resume
__pm_runtime_resume
usb_autopm_get_interface
usbnet_read_cmd
__smsc95xx_read_reg
__smsc95xx_phy_wait_not_busy
__smsc95xx_mdio_read
smsc95xx_mdiobus_read
__mdiobus_read
mdiobus_read
smsc_phy_reset
phy_init_hw
smsc95xx_resume
usb_resume_interface
usb_resume_both
usb_runtime_resume
__rpm_callback
rpm_callback
rpm_resume
__pm_runtime_resume
usb_autoresume_device
hub_event
process_one_work
Fixes: b4df480f68ae ("usbnet: smsc95xx: add reset_resume function with reset operation")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.16+
Cc: Andre Edich <andre.edich@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for BCM53128 internal PHYs. These support interrupts as well as
statistics. Therefore, enable the Broadcom PHY driver for them.
Tested on BCM53128 switch using the mainline b53 DSA driver.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 05ca14fdb6fe65614e0652d03e44b02748d25af7.
On early silicon engineering samples observed bit shrinking issue when
we use brp as 1. Hence updated brp_min as 2. As in production silicon
this issue is fixed, so reverting the patch.
Link: https://lore.kernel.org/all/20220609082433.1191060-2-srinivas.neeli@xilinx.com
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Some structures and defines were added with '_ub_' indication, as there
were equivalent objects for the legacy model.
Now when the legacy model is not used anymore, remove the '_ub_'
indication.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flood_index() function is not needed anymore, as in the unified
bridge model the flood index is calculated using 'mid_base' and
'fid_offset'.
Remove this function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After all the preparations for unified bridge model, finally flip mlxsw
driver to use the new model.
Change config profile, set 'ubridge' to true and remove the configurations
that are relevant only for the legacy model. Set 'flood_mode' to
'controlled' as the current mode is not supported with unified bridge
model.
Remove all the code which is dedicated to the legacy model. Remove
'struct mlxsw_sp.ubridge' variable which was temporarily added to separate
configurations between the models.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The unified bridge model is enabled via the CONFIG_PROFILE command
during driver initialization. Add the definition of the relevant fields
to the command's payload in preparation for unified bridge enablement.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using the legacy bridge model, there is no VID classification at egress
for 802.1Q FIDs, which means that the VID is maintained.
This behavior cause the limitation that 802.1Q FIDs cannot work with VXLAN.
This limitation stems from the fact that a decapsulated VXLAN packet should
not contain a VLAN tag. If such a packet was to egress from a local port
using a 802.1Q FID, it would "maintain" its VLAN on egress, which is no
VLAN at all.
Currently 802.1Q FIDs are emulated in mlxsw driver using 802.1D FIDs. Using
unified bridge model, there is a FID->VID mapping, so it is possible to
stop emulating 802.1Q FIDs.
The main changes are:
1. Use 'SFGC.bridge_type' = 0, to separate between 802.1Q FIDs and
802.1D FIDs.
2. Use VLAN RIF instead of the emulated one (VLAN_EMU which is emulated
using FID RIF).
3. Create VID->FID mapping when the FID is created. Then when a new port
is mapped to the FID, if it not in virtual mode, no new mapping is
needed. Save the new port in 'port_vid_list', to be able to update a
RIF in all {Port, VID}->FID mappings in case that the port will be in
virtual mode later.
4. Add a dedicated operation function per FID family to update RIF for
VID->FID mappings. For 802.1d and rFID families, just return. For
802.1q family, handle the global mapping which is created for new 802.1q
FID.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the unified bridge model, mlxsw will no longer emulate 802.1Q FIDs
using 802.1D FIDs. The new FID table will look as follows:
+---------------+
| 802.1q FIDs | 4K entries
| [1..4094] |
+---------------+
| 802.1d FIDs | 1K entries
| [4095..5118] |
+---------------+
| Dummy FIDs | 1 entry
| [5119..5119] |
+---------------+
| rFIDs | 11K entries
| [5120..16383] |
+---------------+
In order to make the change easier to review, four new temporary FID
families will be added (e.g., MLXSW_SP_FID_TYPE_8021D_UB) and will not
be registered with the FID core until mlxsw is flipped to use the unified
bridge model.
Add .1d, rfid and dummy FID families for unified bridge, the next patch
will add .1q family separately as it requires more changes.
The following changes are required:
1. Add 'smpe_index_valid' field to 'struct mlxsw_sp_fid_family' and set
SFMR.smpe accordingly. SMPE index is reserved for rFIDs, as their
flooding is handled by firmware, and always reserved in Spectrum-1,
as it is configured as part of PGT table.
2. Add 'ubridge' field to 'struct mlxsw_sp_fid_family'. This field will
be removed later, use it in mlxsw_sp_fid_family_{register,unregister}()
to skip the registration / unregistration of the new families when the
legacy model is used.
3. Indexes - the start and end indexes of each FID family will need to be
changed according to the above diagram.
4. Add flood tables for unified bridge model, use 'fid_offset' as table
type, as in the new model the access to flood tables will be using
'fid_offset' calculation.
5. FID family operation changes:
a. rFID supposed to be created using SFMR, as it is not created by
firmware using unified bridge model.
b. port_vid_map() should perform SVFA for rFID, as the mapping is not
created by firmware using unified bridge model.
c. flood_index() is not aligned to the new model, as this function will
be removed later.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Router interfaces (RIFs) constructed on top of VLAN-aware bridges are of
'VLAN' type, whereas RIFs constructed on top of VLAN-unaware bridges are of
'FID' type.
Currently 802.1Q FIDs are emulated using 802.1D FIDs, therefore VLAN RIFs
are emulated using FID RIFs. As part of converting the driver to use
unified bridge model, 802.1Q FIDs and VLAN RIFs will be used.
The egress FID is required for VLAN RIFs in Spectrum-2 and above, but not
in Spectrum-1, as in Spectrum-1 the mapping for VLAN RIFs is VID->FID,
while in other ASICs it is FID->FID. The reason for the change is that it
is more scalable to reuse the FID->FID entry than creating multiple
{Port, VID}->FID entries for the router port. Use the existing operation
structure to separate the configuration between different ASICs.
Add support for VLAN RIFs, most of the configurations are same to FID
RIFs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After routing, a packet needs to perform an L2 lookup using the DMAC it got
from the routing and a FID. In unified bridge model, the egress FID
configuration needs to be performed by software.
It is configured by RITR for both sub-port RIFs and FID RIFs. Currently
FID RIFs already configure eFID. Add eFID configuration for sub-port RIFs.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The field 'vid' in RITR is reserved when unified bridge model is used
and the RIF's type is sub-port RIF. Instead, ingress VID is configured via
SVFA and egress VID is configured via REIV.
Set 'vid' to zero in RITR register for sub-port RIF when unified bridge
model is used.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After routing, the device always consults a table that determines the
packet's egress VID based on {egress RIF, egress local port}. In the
unified bridge model, it is up to software to maintain this table via REIV
register.
The table needs to be updated in the following flows:
1. When a RIF is set on a FID, need to iterate over the FID's {Port, VID}
list and issue REIV write to map the {RIF, Port} to the given VID.
2. When a {Port, VID} is mapped to a FID and the FID already has a RIF,
need to issue REIV write with a single record to map the {RIF, Port}
to the given VID.
REIV register supports a simultaneous update of 256 ports, so use this
capability for the first flow.
Handle the two above mentioned flows.
Add mlxsw_sp_fid_evid_map() function to handle egress VID classification
for both unicast and multicast. Layer 2 multicast configuration is already
done in the driver, just move it to the new function.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before layer 2 forwarding, the device classifies an incoming packet to
a FID. The classification is done based on one of the following keys:
1. FID
2. VNI (after decapsulation)
3. VID / {Port, VID}
After classification, the FID is known, but also all the attributes of
the FID, such as the router interface (RIF) via which a packet that
needs to be routed will ingress the router block.
In the legacy model, when a RIF was created / destroyed, it was
firmware's responsibility to update it in the previously mentioned FID
classification records. In the unified bridge model, this responsibility
moved to software.
The third classification requires to iterate over the FID's {Port, VID}
list and issue SVFA write with the correct mapping table according to the
port's mode (virtual or not). We never map multiple VLANs to the same FID
using VID->FID mapping, so such a mapping needs to be performed once.
When a new FID classification entry is configured and the FID already has
a RIF, set the RIF as part of SVFA configuration.
The reverse needs to be done when clearing a RIF from a FID. Currently,
clearing is done by issuing mlxsw_sp_fid_rif_set() with a NULL RIF pointer.
Instead, introduce mlxsw_sp_fid_rif_unset().
Note that mlxsw_sp_fid_rif_set() is called after the RIF is fully
operational, so it conforms to the internal requirement regarding
SVFA.irif_v: "Must not be set for a non-enabled RIF".
Do not set the ingress RIF for rFIDs, as the {Port, VID}->rFID entry is
configured by firmware when legacy model is used, a next patch will
handle this configuration for rFIDs and unified bridge model.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the new model, SFMR no longer configures both VNI->FID and FID->VNI
classifications, but only the later. The former needs to be configured via
SVFA.
Add SVFA configuration as part of vni_set() and vni_clear().
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using unified bridge model, firmware no longer configures the egress VID
"under the hood" and moves this responsibility to software.
For layer 2, this means that software needs to determine the egress VID
for both unicast (i.e., FDB) and multicast (i.e., MDB and flooding) flows.
Unicast FDB records and unicast LAG FDB records have new fields - "set_vid"
and "vid", set them. For records which point to router port, do not set
these fields.
Signed-off-by: Amit Cohen <amcohen@nvidia.com>
Reviewed-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In vma destruction, the following race may occur:
Thread 1: Thread 2:
i915_vma_destroy();
...
list_del_init(vma->vm_link);
...
mutex_unlock(vma->vm->mutex);
__i915_vm_release();
release_references();
And in release_reference() we dereference vma->vm to get to the
vm gt pointer, leading to a use-after free.
However, __i915_vm_release() grabs the vm->mutex so the vm won't be
destroyed before vma->vm->mutex is released, so extract the gt pointer
under the vm->mutex to avoid the vma->vm dereference in
release_references().
v2: Fix a typo in the commit message (Andi Shyti)
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5944
Fixes: e1a7ab4fca0c ("drm/i915: Remove the vm open count")
Cc: Niranjana Vishwanathapura <niranjana.vishwanathapura@intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Acked-by: Nirmoy Das <nirmoy.das@intel.con>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620123659.381772-1-thomas.hellstrom@linux.intel.com
|
|
Always use crypto_has_comp() so that crypto can lookup module, call
usermodhelper to load the modules, wait for usermodhelper to finish and so
on. Otherwise crypto will do all of these steps under CPU hot-plug lock
and this looks like too much stuff to handle under the CPU hot-plug lock.
Besides this can end up in a deadlock when usermodhelper triggers a code
path that attempts to lock the CPU hot-plug lock, that zram already holds.
An example of such deadlock:
- path A. zram grabs CPU hot-plug lock, execs /sbin/modprobe from crypto
and waits for modprobe to finish
disksize_store
zcomp_create
__cpuhp_state_add_instance
__cpuhp_state_add_instance_cpuslocked
zcomp_cpu_up_prepare
crypto_alloc_base
crypto_alg_mod_lookup
call_usermodehelper_exec
wait_for_completion_killable
do_wait_for_common
schedule
- path B. async work kthread that brings in scsi device. It wants to
register CPUHP states at some point, and it needs the CPU hot-plug
lock for that, which is owned by zram.
async_run_entry_fn
scsi_probe_and_add_lun
scsi_mq_alloc_queue
blk_mq_init_queue
blk_mq_init_allocated_queue
blk_mq_realloc_hw_ctxs
__cpuhp_state_add_instance
__cpuhp_state_add_instance_cpuslocked
mutex_lock
schedule
- path C. modprobe sleeps, waiting for all aync works to finish.
load_module
do_init_module
async_synchronize_full
async_synchronize_cookie_domain
schedule
[senozhatsky@chromium.org: add comment]
Link: https://lkml.kernel.org/r/20220624060606.1014474-1-senozhatsky@chromium.org
Link: https://lkml.kernel.org/r/20220622023501.517125-1-senozhatsky@chromium.org
Signed-off-by: Sergey Senozhatsky <senozhatsky@chromium.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Currently shrinkers are anonymous objects. For debugging purposes they
can be identified by count/scan function names, but it's not always
useful: e.g. for superblock's shrinkers it's nice to have at least an
idea of to which superblock the shrinker belongs.
This commit adds names to shrinkers. register_shrinker() and
prealloc_shrinker() functions are extended to take a format and arguments
to master a name.
In some cases it's not possible to determine a good name at the time when
a shrinker is allocated. For such cases shrinker_debugfs_rename() is
provided.
The expected format is:
<subsystem>-<shrinker_type>[:<instance>]-<id>
For some shrinkers an instance can be encoded as (MAJOR:MINOR) pair.
After this change the shrinker debugfs directory looks like:
$ cd /sys/kernel/debug/shrinker/
$ ls
dquota-cache-16 sb-devpts-28 sb-proc-47 sb-tmpfs-42
mm-shadow-18 sb-devtmpfs-5 sb-proc-48 sb-tmpfs-43
mm-zspool:zram0-34 sb-hugetlbfs-17 sb-pstore-31 sb-tmpfs-44
rcu-kfree-0 sb-hugetlbfs-33 sb-rootfs-2 sb-tmpfs-49
sb-aio-20 sb-iomem-12 sb-securityfs-6 sb-tracefs-13
sb-anon_inodefs-15 sb-mqueue-21 sb-selinuxfs-22 sb-xfs:vda1-36
sb-bdev-3 sb-nsfs-4 sb-sockfs-8 sb-zsmalloc-19
sb-bpf-32 sb-pipefs-14 sb-sysfs-26 thp-deferred_split-10
sb-btrfs:vda2-24 sb-proc-25 sb-tmpfs-1 thp-zero-9
sb-cgroup2-30 sb-proc-39 sb-tmpfs-27 xfs-buf:vda1-37
sb-configfs-23 sb-proc-41 sb-tmpfs-29 xfs-inodegc:vda1-38
sb-dax-11 sb-proc-45 sb-tmpfs-35
sb-debugfs-7 sb-proc-46 sb-tmpfs-40
[roman.gushchin@linux.dev: fix build warnings]
Link: https://lkml.kernel.org/r/Yr+ZTnLb9lJk6fJO@castle
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lkml.kernel.org/r/20220601032227.4076670-4-roman.gushchin@linux.dev
Signed-off-by: Roman Gushchin <roman.gushchin@linux.dev>
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Hillf Danton <hdanton@sina.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Add support for the 1024x600 LVDS panel.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220530122407.918874-2-m.felsch@pengutronix.de
|
|
Add definition of the HannStar HSD101PWW2 Rev0-A00/A01 LCD
SuperIPS+ HD panel.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220529180548.9942-4-clamor95@gmail.com
|
|
The compatible “mediatek,mt8192-disp-rdma” is being used for reading
the data into DMA for back-end panel driver in mt8192 but there is
no difference between mt8183 and mt8192 in rdma driver.
Remove compatible “mediatek,mt8192-disp-rdma” from the driver and
should use “mediatek,mt8183-disp-rdma” as fallback in 8192 DTS
according to the mediatek,rdma.yaml.
Signed-off-by: Allen-KH Cheng <allen-kh.cheng@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Link: https://patchwork.kernel.org/project/linux-mediatek/patch/20220701090547.21429-2-allen-kh.cheng@mediatek.com/
Signed-off-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
|
|
hasdata does not need to be initialized to zero. It will be assigned a
value in the following judgment conditions.
Signed-off-by: Li kunyu <kunyu@nfschina.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Kleine-Budde says:
====================
pull-request: can-next 2022-07-03
this is a pull request of 15 patches for net-next/master.
The first 2 patches are by Max Staudt and add the can327 serial CAN
driver along with a new line discipline ID.
The next patch is by me an fixes a typo in the ctucanfd driver.
The last 12 patches are by Dario Binacchi and integrate slcan CAN
serial driver better into the existing CAN driver API.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It extends the protocol to receive the adapter CAN state changes
(warning, busoff, etc.) and forward them to the netdev upper levels.
Link: https://lore.kernel.org/all/20220628163137.413025-13-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It extends the protocol to receive the adapter CAN communication errors
and forward them to the netdev upper levels.
Link: https://lore.kernel.org/all/20220628163137.413025-12-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch adds a private flag to the slcan driver to switch the
"err-rst-on-open" setting on and off.
"err-rst-on-open" on - Reset error states on opening command
"err-rst-on-open" off - Don't reset error states on opening command
(default)
The setting can only be changed if the interface is down:
ip link set dev can0 down
ethtool --set-priv-flags can0 err-rst-on-open {off|on}
ip link set dev can0 up
Link: https://lore.kernel.org/all/20220628163137.413025-11-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This patch moves the slcan driver into a separate directory, a later
patch will add more files.
Link: https://lore.kernel.org/all/20220628163137.413025-10-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case the bitrate has been set via ip tool, this patch changes the
driver to send the open ("O\r") and close ("C\r) commands to the
adapter.
Link: https://lore.kernel.org/all/20220628163137.413025-9-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It allows to set the bitrate via ip tool, as it happens for the other
CAN device drivers. It still remains possible to set the bitrate via
slcand or slcan_attach utilities. In case the ip tool is used, the
driver will send the serial command to the adapter.
Link: https://lore.kernel.org/all/20220628163137.413025-8-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This is a preparation patch for the upcoming support to change the
bitrate via ip tool, reset the adapter error states via the ethtool API
and, more generally, send commands to the adapter.
Since the close command (i. e. "C\r") will be sent in the ndo_stop()
where netif_running() returns false, a new flag bit (i. e. SLF_XCMD) for
serial transmission has to be added.
Link: https://lore.kernel.org/all/20220628163137.413025-7-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
As suggested by commit [1], now the driver uses the functions and the
data structures provided by the CAN network device driver interface.
Currently the driver doesn't implement a way to set bitrate for SLCAN
based devices via ip tool, so you'll have to do this by slcand or
slcan_attach invocation through the -sX parameter:
- slcan_attach -f -s6 -o /dev/ttyACM0
- slcand -f -s8 -o /dev/ttyUSB0
where -s6 in will set adapter's bitrate to 500 Kbit/s and -s8 to
1Mbit/s.
See the table below for further CAN bitrates:
- s0 -> 10 Kbit/s
- s1 -> 20 Kbit/s
- s2 -> 50 Kbit/s
- s3 -> 100 Kbit/s
- s4 -> 125 Kbit/s
- s5 -> 250 Kbit/s
- s6 -> 500 Kbit/s
- s7 -> 800 Kbit/s
- s8 -> 1000 Kbit/s
In doing so, the struct can_priv::bittiming.bitrate of the driver is not
set and since the open_candev() checks that the bitrate has been set, it
must be a non-zero value, the bitrate is set to a fake value (-1U)
before it is called.
Using the rtnl_lock()/rtnl_unlock() functions has become a bit more
tricky as the register_candev() function indirectly calls rtnl_lock()
via register_netdev(). To avoid a deadlock it is therefore necessary to
call rtnl_unlock() before calling register_candev(). The same goes for
the unregister_candev() function.
[1] commit 39549eef3587f ("can: CAN Network device driver and Netlink interface")
Link: https://lore.kernel.org/all/20220628163137.413025-6-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Upcoming changes on slcan driver will require you to specify a bitrate
of value -1 to prevent the open_candev() from failing but at the same
time highlighting that it is a fake value. In this case the command
`ip --details -s -s link show' would print 4294967295 as the bitrate
value. The patch change this value in 0.
Link: https://lore.kernel.org/all/20220628163137.413025-5-dario.binacchi@amarulasolutions.com
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
It is used successfully by most (if not all) CAN device drivers. It
allows to remove replicated code.
Link: https://lore.kernel.org/all/20220628163137.413025-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Replace printk() calls with corresponding netdev helpers.
Link: https://lore.kernel.org/all/20220628163137.413025-3-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Use the BIT() helper instead of an explicit shift.
Link: https://lore.kernel.org/all/20220628163137.413025-2-dario.binacchi@amarulasolutions.com
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Tested-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add parsing support by implementing struct mlx5e_tc_act for police
action.
TC rule with police actions is broken down into several rules in
different tables. One rule with the original match in the original
flow table, which set fte_id, do metering, and jump to the post_meter
table. If there are more police actions, more rules are created for
each of them. Besides, a last rule is created in the end.
In post_meter table, there are two pre-defined rules, one is to drop
packet if its packet color is RED, the other is to jump back to
post_act table. As fte_id is updated before jumping, the rule for next
meter is matched to do another round of metering (if there are
multiple meters in the flow rule). Otherwise, last fte_id is matched
and do the original actions.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
Nicolas Saenz Julienne
Jimmy Assarsson
Zhang Jiaming
Rick Lindsley
Diana Wang
Marc Kleine-Budde
Liang He
Rhett Aultman
Duy Nguyen
Lukas Wunner
Kurt Kanzenbach
Srinivas Neeli
Amit Cohen
Thomas Hellström
Sergey Senozhatsky
Roman Gushchin
Marco Felsch
Svyatoslav Ryhel
Allen-KH Cheng
Li kunyu
David S. Miller
Dario Binacchi
Jianbo Liu