aboutsummaryrefslogtreecommitdiffstats
path: root/drivers
AgeCommit message (Collapse)AuthorFilesLines
2022-06-21drm/amd/display: Check minimum disp_clk and dpp_clk debug optionRodrigo Siqueira1-0/+19
Our debug struct has the min_disp_clk_khz and min_dpp_clk_khz options, which we ignore in the DCN32. This commit introduces those checks and the necessary calculation. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Fix in dp link-training when updating payload allocation tableDmytro Laktyushkin1-4/+9
[Why & How] Check if aux is not accessible before updating payload allocation table. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: extract update stream allocation to link_hwssWenjing Liu2-6/+10
[Why & How] Extract update stream allocation table into link hwss as part of the link hwss refactor work. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: George Shen <George.Shen@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Remove unused vendor specific w/aGeorge Shen2-130/+4
[Why & How] Old vendor specific w/a are no longer needed and unused. Clean up codebase by removing them. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: George Shen <george.shen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Handle downstream LTTPR with fixed VS sequenceGeorge Shen3-6/+40
[Why] Several issues were discovered that caused link training to fail when an LTTPR device is connected downstream for the fixed VS sequence. [How] The following were added: - workaround to configure AUX timeout for fixed VS sequence - additional delay before disabling fixed VS intercept - detection of fixed VS deadlock state and performing DPCD sequence to recover Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Meenakshikumar Somasundaram <Meenakshikumar.Somasundaram@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: George Shen <George.Shen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Fix typo in override_lane_settingsGeorge Shen1-1/+1
[Why] The function currently skips overriding the drive settings of the first lane. [How] Change for loop to start at 0 instead of 1. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: George Shen <george.shen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Change initializer to single braceAric Cyr3-19/+19
[Why & How] Change struct initializer from multiple brace to single brace. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Aric Cyr <aric.cyr@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: rename lane_settings to hw_lane_settingsWenjing Liu4-15/+14
[why] This is one of the major steps to decouple hw lane settings from dpcd lane settings. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Jun Lei <Jun.Lei@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Fix in overriding DP drive settingsGeorge Shen1-2/+3
[Why & How] Check always_match_dpcd_with_hw_lane_settings bit before overriding the DP drive settings Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: George Shen <george.shen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Enrich the log in MST payload updateWenjing Liu1-0/+6
[Why & How] Enrich the log to provide more informatio in MST payload update. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: Wenjing Liu <wenjing.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Change HDMI judgement condition.JinZe.Xu1-1/+1
[Why & How] Use dc_is_hdmi_signal to determine signal type. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Acked-by: Alan Liu <HaoPing.Liu@amd.com> Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Fix DC warning at driver loadQingqing Zhuo1-1/+1
[Why] Wrong index was checked for dcfclk_mhz, causing false warning. [How] Fix the assertion index. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Add SMU logging codeSaaem Rizvi5-0/+48
[WHY] Logging for SMU response value after the wait allows us to know immediately what the response value was. Makes it easier to debug should the value be anything other than OK. [HOW] Using the the already available DC SMU logging functions. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Saaem Rizvi <SyedSaaem.Rizvi@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Turn off internal backlight when plugging external monitorSung Joon Kim1-2/+1
[why] For VG, we want to turn off power/backlight of the intenral panel when plugging in external monitor and going to "external monitor only" mode. [how] For turning off power of the internal panel, ignore the config flag whic bypasses power sequencing for eDP panels. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Charlene Liu <Charlene.Liu@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Sung Joon Kim <sungkim@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Fix eDP not light up on resumeSung Joon Kim3-1/+13
[why] Only on VG, if external display is disconnected during S3 suspend, the internal panel doesn't light up on resume because we set the power state using an unsupported DPCD register SET_POWER. To check the register is supported, we need to check SET_POWER_CAPABLE first which is eDP-specific DPCD register field. [how] Check the SET_POWER_CAPABLE register field and decide the control of the eDP power state based on the read register value. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Agustin Gutierrez <Agustin.Gutierrez@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Sung Joon Kim <sungkim@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: add mst port output bw checkhersen wu4-3/+48
[Why] when connect one 4k@144hz dp to dsc mst hub, 4k@144hz mode is in valid mode list. but some mst hub port output bandwidth does not support 4k@144hz. [How] add mst port output bandwidth checks, include full_pbn, branch max throughput mps. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: hersen wu <hersenxs.wu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Drop unnecessary detect link codeIan Chen1-5/+0
Delete unnecessary codes in detect_link_and_local_sink. We already have correct stop logic in dc_link_detect. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Ian Chen <ian.chen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Take emulated dc_sink into account for HDCPWayne Lin1-4/+10
[Why] While updating the config of hdcp, we use the sink_singal type of the dc_sink to decide the HDCP operation mode. However, it doesn't consider the case when the sink is a emulated one. [How] Take dc_em_sink into account while updating HDCP config. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Release remote dc_sink under mst scenarioWayne Lin3-22/+35
[Why] Observe that we have several problems while releasing remote dc_sink under mst cases. - When unplug mst branch device from the source, we now try to free all remote dc_sinks in dm_helpers_dp_mst_stop_top_mgr(). However, there are bugs while we're releasing dc_sinks here. First of all, link->remote_sinks[] array get shuffled within dc_link_remove_remote_sink(). As the result, increasing the array index within the releasing loop is wrong. Secondly, it tries to call dc_sink_release() to release the dc_sink of the same aconnector every time in the loop. Which can't release dc_sink of all aconnector in the mst topology. - There is no code path for us to release remote dc_sink for disconnected sst monitor which unplug event is notified by CSN sideband message. Which means we'll use stale dc_sink data to represent later on connected monitor. Also, has chance to break the maximum remote dc_sink number constraint. [How] Distinguish unplug event of mst scenario into 2 cases. * Unplug sst/legacy stream sink off the mst topology - Release related remote dc_sink in detec_ctx(). * Unplug mst branch device off the mst topology - Release related remote dc_sink in early_unregister() Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Revert "drm/amd/display: turn DPMS off on connector unplug"Wayne Lin3-45/+0
This reverts commit 3c4d55c9b9becedd8d31a7c96783a364533713ab. Revert the commit because: - It's incomplete of the function dm_set_dpms_off() for mst case. For stream sinks whithin the same mst topology, they share the same dc_link. dm_set_dpms_off() tries to update one mst stream only which is incomplete. - Setting dpms off should be triggered by usermode. Besdies, it seems usermode does release relevant resource for mst & non-mst case when unplug connecotr now. Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Revert "drm/amd/display: Add flag to detect dpms force off during HPD"Wayne Lin3-25/+11
This reverts commit 035f54969bb2c1a5ced52f43e4ef393e0c0f6bfa. The reverted commit was trying to fix side effect brought by commit 3c4d55c9b9be ("drm/amd/display: turn DPMS off on connector unplug") However, * This reverted commit will have mst case never call dm_set_dpms_off() which conflicts the idea of original commit 3c4d55c9b9be ("drm/amd/display: turn DPMS off on connector unplug") That's due to dm_crtc_state is always null since the input parameter aconnector is the root device (source) of mst topology. It's not an end stream sink within the mst topology. * Setting dpms off should be triggered by usermode. Besdies, it seems usermode does release relevant resource for mst & non-mst case when unplug connecotr now. Which means we no longer need both commits now: commit 3c4d55c9b9be ("drm/amd/display: turn DPMS off on connector unplug") commit 035f54969bb2 ("drm/amd/display: Add flag to detect dpms force off during HPD") Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Acked-by: Lyude Paul <lyude@redhat.com> Signed-off-by: Wayne Lin <Wayne.Lin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd: Revert "drm/amd/display: keep eDP Vdd on when eDP stream is already enabled"Mario Limonciello1-22/+2
A variety of Lenovo machines with Rembrandt APUs and OLED panels have stopped showing the display at login. This behavior clears up after leaving it idle and moving the mouse or touching keyboard. It was bisected to be caused by commit 559e2655220d ("drm/amd/display: keep eDP Vdd on when eDP stream is already enabled"). Revert this commit to fix the issue. Link: https://gitlab.freedesktop.org/drm/amd/-/issues/2047 Reported-by: Aaron Ma <aaron.ma@canonical.com> Fixes: 559e2655220d ("drm/amd/display: keep eDP Vdd on when eDP stream is already enabled") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Tested-by: Mark Pearson <markpearson@lenovo.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: Remove compiler warningCruise Hung1-1/+1
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Cruise Hung <Cruise.Hung@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu: add LSDMA block for LSDMA v6.0.1Yifan Zhang1-0/+1
This patch adds LSDMA ip block for LSDMA v6.0.1. Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com> Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/display: add missing reg defs for DCN3x HUBBUBAurabindo Pillai5-0/+13
[Why&How] The omitted register definition caused call traces like: [ 3.811215] WARNING: CPU: 7 PID: 794 at drivers/gpu/drm/amd/amdgpu/../display/dc/dc_helper.c:120 set_reg_field_values.constprop.0+0xc7/0xe0 [amdgpu] [ 3.811406] Modules linked in: amdgpu(+) drm_ttm_helper ttm iommu_v2 gpu_sched drm_kms_helper cfbfillrect syscopyarea cfbimgblt sysfillrect sysimgblt fb_sys_fops cfbcopyarea drm i2c_piix4 drm_panel_orientation_quirks [ 3.811419] CPU: 7 PID: 794 Comm: systemd-udevd Not tainted 5.16.0-kfd+ #132 [ 3.811422] Hardware name: System manufacturer System Product Name/ROG STRIX B450-F GAMING, BIOS 3003 12/09/2019 [ 3.811425] RIP: 0010:set_reg_field_values.constprop.0+0xc7/0xe0 [amdgpu] [ 3.811615] Code: 08 49 89 51 08 8b 08 48 8d 42 08 49 89 41 08 44 8b 02 48 8d 50 08 0f b6 c9 49 89 51 08 8b 00 45 85 c0 75 b3 0f 0b eb af 5d c3 <0f> 0b e9 48 ff ff ff 49 8b 51 08 eb d0 49 8b 41 08 eb d5 66 0f 1f [ 3.811619] RSP: 0018:ffffb8c1c04cf640 EFLAGS: 00010246 [ 3.811621] RAX: 0000000000000000 RBX: ffff96f2100d8800 RCX: 0000000000000000 [ 3.811623] RDX: 0000000000000000 RSI: 0000000000000001 RDI: ffffb8c1c04cf650 [ 3.811625] RBP: ffffb8c1c04cf640 R08: 000000000000047f R09: ffffb8c1c04cf658 [ 3.811627] R10: ffff96f5161ff000 R11: ffff96f5161ff000 R12: ffff96f204afb9c0 [ 3.811629] R13: 0000000000000000 R14: ffff96f202b94c00 R15: ffffb8c1c04cf718 [ 3.811631] FS: 00007fe07c2e2880(0000) GS:ffff96f5059c0000(0000) knlGS:0000000000000000 [ 3.811634] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 3.811636] CR2: 0000559634ab57b8 CR3: 0000000120674000 CR4: 00000000003506e0 [ 3.811637] Call Trace: [ 3.811640] <TASK> [ 3.811642] generic_reg_update_ex+0x69/0x200 [amdgpu] [ 3.811831] ? _printk+0x58/0x6f [ 3.811836] dcn32_init_crb+0x18f/0x1b0 [amdgpu] [ 3.812031] dcn32_init_hw+0x379/0x6a0 [amdgpu] [ 3.812223] dc_hardware_init+0xba/0x100 [amdgpu] [ 3.812415] amdgpu_dm_init.isra.0.cold+0x166/0x1867 [amdgpu] [ 3.812616] ? dev_vprintk_emit+0x139/0x15d [ 3.812621] ? dev_printk_emit+0x4e/0x65 [ 3.812624] dm_hw_init+0x12/0x30 [amdgpu] [ 3.812820] amdgpu_device_init.cold+0x130d/0x178c [amdgpu] [ 3.813017] ? pci_read_config_word+0x25/0x40 [ 3.813021] amdgpu_driver_load_kms+0x1a/0x130 [amdgpu] [ 3.813178] amdgpu_pci_probe+0x130/0x330 [amdgpu] Fixes: 4f29f9cf092b ("drm/amd: add register headers for DCN32/321") Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com> Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd: Don't show warning on reading vbios values for SMU13 3.1Mario Limonciello1-0/+2
Some APUs with SMU13 are showing the following message: `amdgpu 0000:63:00.0: amdgpu: Unexpected and unhandled version: 3.1` This warning isn't relevant for smu info 3.1, as no bootup information is present in the table. Fixes: 593a54f18031 ("drm/amd/pm: correct the way for retrieving bootup clocks") Signed-off-by: Mario Limonciello <mario.limonciello@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amd/pm: skip to set mp1 unload state in special caseYang Wang1-5/+6
set mp1 unload state will cause the SMC FW can't accept any SMU message, skip to set mp1 unload state to avoid following case fail: - runtime pm case. - gpu reset case. Fixes: 72aeb6ee0c78 ("drm/amd/pm: fix driver reload SMC firmware fail issue for smu13") Signed-off-by: Yang Wang <KevinYang.Wang@amd.com> Reviewed-by: Kenneth Feng <kenneth.feng@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu/gmc11: avoid cpu accessing registers to flush VMJack Xiao1-1/+50
Due to gfxoff on, cpu accessing registers is not expected. Signed-off-by: Jack Xiao <Jack.Xiao@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu/pm: adjust EccInfo_t structStanley.Yang1-1/+2
The EccInfo_t struct in driver_if.h is as below in official release verion 68.55.0 typedef struct { uint64_t mca_umc_status; uint64_t mca_umc_addr; uint16_t ce_count_lo_chip; uint16_t ce_count_hi_chip; uint32_t eccPadding; uint64_t mca_ceumc_addr; } EccInfo_t; It's different from the debug version druing develop print correctable error address, so adjust EccInfo_t struct. Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu: Adjust logic around GTT size (v3)Alex Deucher1-6/+14
Certain GL unit tests for large textures can cause problems with the OOM killer since there is no way to link this memory to a process. This was originally mitigated (but not necessarily eliminated) by limiting the GTT size. The problem is this limit is often too low for many modern games so just make the limit 1/2 of system memory. The OOM accounting needs to be addressed, but we shouldn't prevent common 3D applications from being usable just to potentially mitigate that corner case. Set default GTT size to max(3G, 1/2 of system ram) by default. v2: drop previous logic and default to 3/4 of ram v3: default to half of ram to align with ttm v4: fix spelling in comment (Kent) Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1942 Reviewed-by: Marek Olšák <marek.olsak@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/radeon: fix incorrrect SPDX-License-IdentifiersAlex Deucher3-3/+3
radeon is MIT. This were incorrectly changed in commit b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license") and commit d198b34f3855 (".gitignore: add SPDX License Identifier") and: commit ec8f24b7faaf ("treewide: Add SPDX license identifier - Makefile/Kconfig") Fixes: d198b34f3855 (".gitignore: add SPDX License Identifier") Fixes: ec8f24b7faaf ("treewide: Add SPDX license identifier - Makefile/Kconfig") Fixes: b24413180f56 ("License cleanup: add SPDX GPL-2.0 license identifier to files with no license") Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/2053 Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu: Remove break for VMID loop TLB flush on MESGraham Sider2-2/+2
Loop through all VMIDs for gmc_v10_0_flush_gpu_tlb_pasid and gmc_v11_0_flush_gpu_tlb_pasid (only if using MES for gmc_v10). This is required for MES due to use_different_vmid_compute causing SDMA queues to be assigned different VMIDs than compute for the same PASID. Signed-off-by: Graham Sider <Graham.Sider@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu/vcn: adjust unified queue code formatRuijing Dong2-10/+10
Fixed some errors and warnings found by checkpatch.pl. Acked-by: Christian König <christian.koenig@amd.com> Signed-off-by: Ruijing Dong <ruijing.dong@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu/vcn: support unified queue only in vcn4Ruijing Dong1-422/+139
- remove multiple queue support - add unified queue related functions Acked-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Ruijing Dong <ruijing.dong@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21drm/amdgpu/vcn: add unified queue ib testRuijing Dong2-3/+100
- add unified queue headers - add unified queue ib tests Acked-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Ruijing Dong <ruijing.dong@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2022-06-21cxl/mbox: Use __le32 in get,set_lsa mailbox structuresAlison Schofield2-7/+7
CXL specification defines these as little endian. Fixes: 60b8f17215de ("cxl/pmem: Translate NVDIMM label commands to CXL label commands") Reported-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: Alison Schofield <alison.schofield@intel.com> Link: https://lore.kernel.org/r/20220225221456.1025635-1-alison.schofield@intel.com Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2022-06-21cxl/core: Use is_endpoint_decoderBen Widawsky3-2/+3
Save some characters and directly check decoder type rather than port type. There's no need to check if the port is an endpoint port since, by this point, cxl_endpoint_decoder_alloc() has a specified type. Reviewed by: Adam Manzanares <a.manzanares@samsung.com> Signed-off-by: Ben Widawsky <ben.widawsky@intel.com> Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2022-06-21cxl: Fix cleanup of port devices on failure to probe driver.Jonathan Cameron1-1/+6
The device is created, and then there is a check if a driver succesfully bound to it. In event of failing the bind (e.g. failure in cxl_port_probe()) the device is left registered. When a bus rescan later occurs, fresh devices are created leading to a multiple device representing the same underlying hardware. Bad things may follow and at very least we have far too many devices. Fix by ensuring autoremove is registered if the device create succeeds, but doesn't depend on sucessful binding to a driver. Bug was observed as side effect of incorrect ownership in [PATCH v9 6/9] cxl/port: Read CDAT table but will result from any failure to in cxl_port_probe(). Fixes: 8dd2bc0f8e02 ("cxl/mem: Add the cxl_mem driver") Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Reviewed-by: Ira Weiny <ira.weiny@intel.com> Link: https://lore.kernel.org/r/20220609134519.11668-1-Jonathan.Cameron@huawei.com Signed-off-by: Dan Williams <dan.j.williams@intel.com>
2022-06-21intel/i40e: delete if NULL check before dev_kfree_skbBernard Zhao1-4/+2
dev_kfree_skb check if the input parameter NULL and do the right thing, there is no need to check again. This change is to cleanup the code a bit. Signed-off-by: Bernard Zhao <zhaojunkui2008@126.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-06-21i40e: Remove unnecessary synchronize_irq() before free_irq()Minghao Chi1-2/+0
Calling synchronize_irq() right before free_irq() is quite useless. On one hand the IRQ can easily fire again before free_irq() is entered, on the other hand free_irq() itself calls synchronize_irq() internally (in a race condition free way), before any state associated with the IRQ is freed. Reported-by: Zeal Robot <zealci@zte.com.cn> Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-06-21i40e: Add support for ethtool -s <interface> speed <speed in Mb>Mateusz Palczewski1-0/+90
Add ability to change speed through ethtool -s <interface> speed <speed in Mb> Driver advertises all link modes that support requested speed. Autoneg must be set off e.g.: ethtool -s <interface> autoneg off speed <speed in Mb>. Add helper function that translate speed in Mb to enum i40e_aq_link_speed and compare it to supported speeds from given ethtool_link_ksettings. Add in i40e_set_link_ksettings hold for requested speed and set copy_ks.base.speed to safe_ks.base.speed to be sure that user is not changing unsupported setting. In i40e_speed_to_link_speed compare requested speed with supported speeds. Set speed to requested speed. Signed-off-by: Norbert Zulinski <norbertx.zulinski@intel.com> Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com> Tested-by: Dave Switzer <david.switzer@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-06-21ice: ethtool: advertise 1000M speeds properlyAnatolii Gerasymenko1-1/+38
In current implementation ice_update_phy_type enables all link modes for selected speed. This approach doesn't work for 1000M speeds, because both copper (1000baseT) and optical (1000baseX) standards cannot be enabled at once. Fix this, by adding the function `ice_set_phy_type_from_speed()` for 1000M speeds. Fixes: 48cb27f2fd18 ("ice: Implement handlers for ethtool PHY/link operations") Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com> Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel) Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-06-21iio: chemical: sps30: Move symbol exports into IIO_SPS30 namespaceJonathan Cameron3-1/+3
Avoid unnecessary pollution of the global symbol namespace by moving library functions in to a specific namespace and import that into the drivers that make use of the functions. For more info: https://lwn.net/Articles/760045/ Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Cc: Tomasz Duszynski <tomasz.duszynski@octakon.com> Link: https://lore.kernel.org/r/20220220173701.502331-4-jic23@kernel.org Reviewed-By: Joe Simmons-Talbott <joetalbott@gmail.com> Link: https://lore.kernel.org/r/20220604155306.422937-4-jic23@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2022-06-21iio: pressure: bmp280: Move symbol exports to IIO_BMP280 namespaceJonathan Cameron4-3/+5
Avoid unnecessary pollution of the global symbol namespace by moving library functions in to a specific namespace and import that into the drivers that make use of the functions. For more info: https://lwn.net/Articles/760045/ Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20220220173701.502331-3-jic23@kernel.org Reviewed-By: Joe Simmons-Talbott <joetalbott@gmail.com> Link: https://lore.kernel.org/r/20220604155306.422937-3-jic23@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2022-06-21iio: imu: bmi160: Move exported symbols to IIO_BMI160 namespaceJonathan Cameron3-3/+5
Avoid unnecessary pollution of the global symbol namespace by moving library functions in to a specific namespace and import that into the drivers that make use of the functions. For more info: https://lwn.net/Articles/760045/ Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> Link: https://lore.kernel.org/r/20220220173701.502331-2-jic23@kernel.org Reviewed-By: Joe Simmons-Talbott <joetalbott@gmail.com> Link: https://lore.kernel.org/r/20220604155306.422937-2-jic23@kernel.org Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
2022-06-21ice: Fix switchdev rules book keepingWojciech Drewek1-0/+1
Adding two filters with same matching criteria ends up with one rule in hardware with act = ICE_FWD_TO_VSI_LIST. In order to remove them properly we have to keep the information about vsi handle which is used in VSI bitmap (ice_adv_fltr_mgmt_list_entry::vsi_list_info::vsi_map). Fixes: 0d08a441fb1a ("ice: ndo_setup_tc implementation for PF") Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com> Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com> Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com> Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
2022-06-21drm/nouveau/mmu: drop unexpected word "the" in the commentsJiang Jian1-1/+1
there is an unexpected word "the" in the comments that need to be dropped file: drivers/gpu/drm/nouveau/nvkm/subdev/mmu/vmm.c line: 1051 * have the the deepest nesting of page tables. changed to * have the deepest nesting of page tables. Signed-off-by: Jiang Jian <jiangjian@cdjrlc.com> Signed-off-by: Lyude Paul <lyude@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220621133920.8112-1-jiangjian@cdjrlc.com
2022-06-21mwifiex: fix sleep in atomic context bugs caused by dev_coredumpvDuoming Zhou3-8/+10
There are sleep in atomic context bugs when uploading device dump data in mwifiex. The root cause is that dev_coredumpv could not be used in atomic contexts, because it calls dev_set_name which include operations that may sleep. The call tree shows execution paths that could lead to bugs: (Interrupt context) fw_dump_timer_fn mwifiex_upload_device_dump dev_coredumpv(..., GFP_KERNEL) dev_coredumpm() kzalloc(sizeof(*devcd), gfp); //may sleep dev_set_name kobject_set_name_vargs kvasprintf_const(GFP_KERNEL, ...); //may sleep kstrdup(s, GFP_KERNEL); //may sleep The corresponding fail log is shown below: [ 135.275938] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start [ 135.281029] BUG: sleeping function called from invalid context at include/linux/sched/mm.h:265 ... [ 135.293613] Call Trace: [ 135.293613] <IRQ> [ 135.293613] dump_stack_lvl+0x57/0x7d [ 135.293613] __might_resched.cold+0x138/0x173 [ 135.293613] ? dev_coredumpm+0xca/0x2e0 [ 135.293613] kmem_cache_alloc_trace+0x189/0x1f0 [ 135.293613] ? devcd_match_failing+0x30/0x30 [ 135.293613] dev_coredumpm+0xca/0x2e0 [ 135.293613] ? devcd_freev+0x10/0x10 [ 135.293613] dev_coredumpv+0x1c/0x20 [ 135.293613] ? devcd_match_failing+0x30/0x30 [ 135.293613] mwifiex_upload_device_dump+0x65/0xb0 [ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0 [ 135.293613] call_timer_fn+0x122/0x3d0 [ 135.293613] ? msleep_interruptible+0xb0/0xb0 [ 135.293613] ? lock_downgrade+0x3c0/0x3c0 [ 135.293613] ? __next_timer_interrupt+0x13c/0x160 [ 135.293613] ? lockdep_hardirqs_on_prepare+0xe/0x220 [ 135.293613] ? mwifiex_dnld_fw+0x1b0/0x1b0 [ 135.293613] __run_timers.part.0+0x3f8/0x540 [ 135.293613] ? call_timer_fn+0x3d0/0x3d0 [ 135.293613] ? arch_restore_msi_irqs+0x10/0x10 [ 135.293613] ? lapic_next_event+0x31/0x40 [ 135.293613] run_timer_softirq+0x4f/0xb0 [ 135.293613] __do_softirq+0x1c2/0x651 ... [ 135.293613] RIP: 0010:default_idle+0xb/0x10 [ 135.293613] RSP: 0018:ffff888006317e68 EFLAGS: 00000246 [ 135.293613] RAX: ffffffff82ad8d10 RBX: ffff888006301cc0 RCX: ffffffff82ac90e1 [ 135.293613] RDX: ffffed100d9ff1b4 RSI: ffffffff831ad140 RDI: ffffffff82ad8f20 [ 135.293613] RBP: 0000000000000003 R08: 0000000000000000 R09: ffff88806cff8d9b [ 135.293613] R10: ffffed100d9ff1b3 R11: 0000000000000001 R12: ffffffff84593410 [ 135.293613] R13: 0000000000000000 R14: 0000000000000000 R15: 1ffff11000c62fd2 ... [ 135.389205] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end This patch uses delayed work to replace timer and moves the operations that may sleep into a delayed work in order to mitigate bugs, it was tested on Marvell 88W8801 chip whose port is usb and the firmware is usb8801_uapsta.bin. The following is the result after using delayed work to replace timer. [ 134.936453] usb 1-1: == mwifiex dump information to /sys/class/devcoredump start [ 135.043344] usb 1-1: == mwifiex dump information to /sys/class/devcoredump end As we can see, there is no bug now. Fixes: f5ecd02a8b20 ("mwifiex: device dump support for usb interface") Reviewed-by: Brian Norris <briannorris@chromium.org> Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/b63b77fc84ed3e8a6bef02378e17c7c71a0bc3be.1654569290.git.duoming@zju.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-21devcoredump: remove the useless gfp_t parameter in dev_coredumpv and dev_coredumpmDuoming Zhou19-39/+30
The dev_coredumpv() and dev_coredumpm() could not be used in atomic context, because they call kvasprintf_const() and kstrdup() with GFP_KERNEL parameter. The process is shown below: dev_coredumpv(.., gfp_t gfp) dev_coredumpm(.., gfp_t gfp) dev_set_name kobject_set_name_vargs kvasprintf_const(GFP_KERNEL, ...); //may sleep kstrdup(s, GFP_KERNEL); //may sleep This patch removes gfp_t parameter of dev_coredumpv() and dev_coredumpm() and changes the gfp_t parameter of kzalloc() in dev_coredumpm() to GFP_KERNEL in order to show they could not be used in atomic context. Fixes: 833c95456a70 ("device coredump: add new device coredump class") Reviewed-by: Brian Norris <briannorris@chromium.org> Reviewed-by: Johannes Berg <johannes@sipsolutions.net> Signed-off-by: Duoming Zhou <duoming@zju.edu.cn> Link: https://lore.kernel.org/r/df72af3b1862bac7d8e793d1f3931857d3779dfd.1654569290.git.duoming@zju.edu.cn Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-21drm/dp_mst: Get rid of old comment in drm_atomic_get_mst_topology_state docsLyude Paul1-2/+1
We don't actually care about connection_mutex here anymore, so let's get rid of the comment mentioning it in this function's kdocs. Signed-off-by: Lyude Paul <lyude@redhat.com> Reviewed-by: Wayne Lin <Wayne.Lin@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220602201757.30431-4-lyude@redhat.com
Copyright © 1996 – 2026 Jason A. Donenfeld. All Rights Reverse Engineered.