| Age | Commit message (Collapse) | Author | Files | Lines |
|
Commit 680532c50bca ("drm: adv7511: Add support for
i2c_new_secondary_device") allows a device tree node to override
the default addresses of the secondary i2c devices. This is useful
for solving address conflicts on the i2c bus.
In adv7511_init_cec_regmap() the new i2c address of cec device is
read from device tree and immediately accessed, well before it is
written in the proper register to override the default address.
This can cause an i2c error during probe and a consequent probe
failure.
Once the new i2c address is read from the device tree, override
the default address before any attempt to access the cec.
Tested with adv7533 and stm32mp157f.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Fixes: 680532c50bca ("drm: adv7511: Add support for i2c_new_secondary_device")
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220607213144.427177-1-antonio.borneo@foss.st.com
|
|
fa84f89395e0 ("irqchip/loongson-liointc: Fix build error for
LoongArch") replaced get_ebase_cpunum with physical processor
id from SMP facilities. However that breaks MIPS non-SMP build
and makes booting from other cores inpossible on non-SMP kernel.
Thus we revert get_ebase_cpunum back and use get_csr_cpuid for
LoongArch.
Fixes: fa84f89395e0 ("irqchip/loongson-liointc: Fix build error for LoongArch")
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220609175242.977-1-jiaxun.yang@flygoat.com
|
|
Fix the "comparison with less than zero" warning reported by
cppcheck for the unsigned (size_t) parameter count of the
alt_pr_fpga_write() function.
Fixes: d201cc17a8a3 ("fpga pr ip: Core driver support for Altera Partial Reconfiguration IP")
Reviewed-by: Tom Rix <trix@redhat.com>
Acked-by: Xu Yilun <yilun.xu@intel.com>
Signed-off-by: Marco Pagani <marpagan@redhat.com>
Link: https://lore.kernel.org/r/20220609140520.42662-1-marpagan@redhat.com
Signed-off-by: Xu Yilun <yilun.xu@intel.com>
|
|
We would like to make chip_info table const, but 8821c uses one field as
a variable, and causes core dump. To fix this, move the field to another
struct that can be read and written.
BUG: unable to handle page fault for address: ffffffffc09f52f4
PGD 5b5215067 P4D 5b5215067 PUD 5b5217067 PMD 111f61067 PTE 8000000111e07161
Oops: 0003 [#1] PREEMPT SMP NOPTI
CPU: 6 PID: 436 Comm: NetworkManager Not tainted 5.18.0-rc7-debug-01822-g89d8f53ff6e7 #1 5cac31ca93432e53341863abfb3332fd98b144da
Hardware name: HP HP Desktop M01-F1xxx/87D6, BIOS F.12 12/17/2020
RIP: 0010:rtw8821c_phy_set_param+0x262/0x380 [rtw88_8821c]
Code: e8 53 f3 c0 d6 48 8b 43 10 4c 8b 63 38 be 24 0a 00 00 48 89 df 48
8b 40 68 e8 3a f3 c0 d6 89 e9 be 28 0a 00 00 48 89 df d3 e8 <41> 89 84
24 54 01 00 00 48 8b 43 10 4c 8b 63 38 48 8b 40 68 e8 15
RSP: 0018:ffffb08c417cb6f0 EFLAGS: 00010286
RAX: 0000000064b80c1c RBX: ffff93d15a0120e0 RCX: 0000000000000000
RDX: 0000000034028211 RSI: 0000000000000a28 RDI: ffff93d15a0120e0
RBP: 0000000000000000 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000006 R12: ffffffffc09f51a0
R13: ffff93d15a0156d0 R14: 0000000000000000 R15: 0000000000000001
FS: 00007f4e9b73d1c0(0000) GS:ffff93d83ab80000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffffffffc09f52f4 CR3: 0000000103b9e000 CR4: 0000000000350ee0
Call Trace:
<TASK>
rtw_core_start+0xbd/0x190 [rtw88_core de79d6bdfd083d102030858972032e5706726279]
rtw_ops_start+0x26/0x40 [rtw88_core de79d6bdfd083d102030858972032e5706726279]
drv_start+0x42/0x100 [mac80211 21e803d0ad10691f64c6c81ecc24c0c6c36e5d58]
ieee80211_do_open+0x2fb/0x900 [mac80211 21e803d0ad10691f64c6c81ecc24c0c6c36e5d58]
ieee80211_open+0x67/0x80 [mac80211 21e803d0ad10691f64c6c81ecc24c0c6c36e5d58]
__dev_open+0xdd/0x180
[...]
Fixes: 89d8f53ff6e7 ("wifi: rtw88: Fix Sparse warning for rtw8821c_hw_spec")
Reported-by: Nathan Chancellor <nathan@kernel.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608020312.9663-1-pkshih@realtek.com
|
|
Add an new state, RTW89_PHY_DCFO_STATE_HOLD, to keep CFO acceleration
after CFO_PERIOD_CNT if the traffic is UL-OFDMA, which is calculated
based on RX trigger frame counter.
Signed-off-by: Eric Huang <echuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-4-pkshih@realtek.com
|
|
Adding this allows us to maintain trigger frame statistics, which is
required for our CFO tracking decisions.
Signed-off-by: Po Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220608113224.11193-3-pkshih@realtek.com
|
|
release_firmware() checks for NULL pointers internally so checking
before calling it is redundant.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Acked-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20220606014237.290466-1-chi.minghao@zte.com.cn
|
|
rtw_read32() reads data from device via USB API which may fail. In case
of any failure previous code returned stack data to callers, which is
wrong.
Fix it by changing rtw_read32() prototype and prevent caller from
touching random stack data
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/583c3d21c46066275e4fc8da5ba4fd0e3679335b.1654629778.git.paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
rtw_read16() reads data from device via USB API which may fail. In case
of any failure previous code returned stack data to callers, which is
wrong.
Fix it by changing rtw_read16() prototype and prevent caller from
touching random stack data
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/06b45afda048d0aeddeed983c2318680fe6265f5.1654629778.git.paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
rtw_read8() reads data from device via USB API which may fail. In case
of any failure previous code returned stack data to callers, which is
wrong.
Fix it by changing rtw_read8() prototype and prevent caller from
touching random stack data
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Link: https://lore.kernel.org/r/c8f8ef4f14db3ba2478a87d5be6eb768a093dfaf.1654629778.git.paskripkin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The pwep allocation was always being allocated smaller than the true
structure size. Avoid this by always allocating the full structure.
Found with GCC 12 and -Warray-bounds:
../drivers/staging/rtl8723bs/os_dep/ioctl_linux.c: In function 'rtw_set_encryption':
../drivers/staging/rtl8723bs/os_dep/ioctl_linux.c:591:29: warning: array subscript 'struct ndis_802_11_wep[0]' is partly outside array bounds of 'void[25]' [-Warray-bounds]
591 | pwep->length = wep_total_len;
| ^~
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Fabio Aiuto <fabioaiuto83@gmail.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: linux-staging@lists.linux.dev
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220608215512.1070847-1-keescook@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The commit eecb3e4e5d9d ("staging: olpc_dcon: add OLPC display controller
(DCON) support") added this driver in 2010, and has been in staging since
then. It was marked as broken at some point because it didn't even build
but that got removed once the build issues were addressed.
But it seems that the work to move this driver out of staging has stalled,
the last non-trivial change to fix one of the items mentioned in its todo
file was commit e40219d5e4b2 ("staging: olpc_dcon: allow simultaneous XO-1
and XO-1.5 support") in 2019.
And even if work to destage the driver is resumed, the fbdev subsystem has
been deprecated for a long time and instead it should be ported to DRM.
Now this driver is preventing to land a kernel wide change, that makes the
num_registered_fb symbol to be private to the fbmem.c file.
So let's just mark the driver as broken. Someone can then work on making
it not depend on the num_registered_fb symbol, allowing to drop the broken
dependency again.
Suggested-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://lore.kernel.org/r/20220609223424.907174-1-javierm@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
simplify do-while loops into for loops
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Srivathsan Sivakumar <sri.skumar05@gmail.com>
Link: https://lore.kernel.org/r/YqJcLwUQorZQOrkd@Sassy
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
backlight_properties.fb_blank is deprecated. The states it represents
are handled by other properties; but instead of accessing those
properties directly, drivers should use the helpers provided by
backlight.h.
Instead of manually checking the power state in struct
backlight_properties, use backlight_is_blank().
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Noralf Trønnes" <noralf@tronnes.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Len Baker <len.baker@gmx.com>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-staging@lists.linux.dev
Reviewed-by: Daniel Thompson <daniel.thompson@linaro.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220607185516.1129900-1-steve@sk2.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This patch adds a blank line after the variable declarations,
it should remove a checkpatch.pl warning and improve readability.
checkpatch output:
WARNING: Missing a blank line after declarations
Signed-off-by: Rommel Rodriguez Perez <alrodperez@gmail.com>
Link: https://lore.kernel.org/r/YqALs/7VkGsYUngw@debianmain.debian.pc.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Instead of retrieving the backlight brightness in struct
backlight_properties manually, and then checking whether the backlight
should be on at all, use backlight_get_brightness() which does all
this and insulates this from future changes.
Cc: Jens Frederich <jfrederich@gmail.com>
Cc: Jon Nettleton <jon.nettleton@gmail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-staging@lists.linux.dev
Signed-off-by: Stephen Kitt <steve@sk2.org>
Link: https://lore.kernel.org/r/20220607190049.1132154-1-steve@sk2.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Setting RLB_NULL_INDEX is not needed as this is done in bond_alb_initialize
which is called by bond_open.
Also reduce the number of rtnl_unlock calls by just using the standard
goto cleanup path.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for reporting errors via extack in both bond_newlink
and bond_changelink.
Instead of having to look in the kernel log for why an option was not
correct just report the error to the user via the extack variable.
What is currently reported today:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
RTNETLINK answers: Device or resource busy
After this change:
ip link add bond0 type bond
ip link set bond0 up
ip link set bond0 type bond mode 4
Error: unable to set option because the bond is up.
Signed-off-by: Jonathan Toppins <jtoppins@redhat.com>
Acked-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-06-08
Michal prevents setting of VF VLAN capabilities in switchdev mode and
removes, not needed, specific switchdev VLAN operations.
Karol converts u16 variables to unsigned int for GNSS calculations.
Christophe Jaillet corrects the parameter order for a couple of
devm_kcalloc() calls.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: Use correct order for the parameters of devm_kcalloc()
ice: remove u16 arithmetic in ice_gnss
ice: remove VLAN representor specific ops
ice: don't set VF VLAN caps in switchdev
====================
Link: https://lore.kernel.org/r/20220608160757.2395729-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Saeed Mahameed says:
====================
mlx5 fixes 2022-06-08
This series provides bug fixes to mlx5 driver.
* tag 'mlx5-fixes-2022-06-08' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: fs, fail conflicting actions
net/mlx5: Rearm the FW tracer after each tracer event
net/mlx5: E-Switch, pair only capable devices
net/mlx5e: CT: Fix cleanup of CT before cleanup of TC ct rules
Revert "net/mlx5e: Allow relaxed ordering over VFs"
MAINTAINERS: adjust MELLANOX ETHERNET INNOVA DRIVERS to TLS support removal
====================
Link: https://lore.kernel.org/r/20220608185855.19818-1-saeed@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Swap around the GRE and VLAN parts in the flow-key offloaded by
the driver to fit in with other tunnel types and the firmware.
Without this change used cases with GRE+VLAN on the outer header
does not get offloaded as the flow-key mismatches what the
firmware expect.
Fixes: 0d630f58989a ("nfp: flower: add support to offload QinQ match")
Fixes: 5a2b93041646 ("nfp: flower-ct: compile match sections of flow_payload")
Signed-off-by: Etienne van der Linde <etienne.vanderlinde@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nfp_net_sriov_check is added in nfp_app_get_vf_config which intends
to ensure ivi->vlan_proto and ivi->max_tx_rate/min_tx_rate can be
read from VF config table only when firmware supports corresponding
capability.
However, "nfp_app_get_vf_config" can be called by commands like
"ip a", "ip link set $DEV up" and "ip link set $DEV vf $NUM vlan
$param" (with VF). When using commands above, many warnings
"ndo_set_vf_<cap_x> not supported" would appear if firmware doesn't
support VF rate limit and 802.1ad VLAN assingment. If more VFs are
created, things could get worse.
Thus, this patch add an extra bool parameter for nfp_net_sriov_check
to enable/disable the cap check warning report. Unnecessary warnings
in nfp_app_get_vf_config can be avoided. Valid warnings in kinds of
vf setting function can be reserved.
Fixes: e0d0e1fdf1ed ("nfp: VF rate limit support")
Fixes: 59359597b010 ("nfp: support 802.1ad VLAN assingment to VF")
Signed-off-by: Fei Qin <fei.qin@corigine.com>
Signed-off-by: Yinjun Zhang <yinjun.zhang@corigine.com>
Signed-off-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have a convenient helper, let's use it.
This will make the following patch easier to review and smaller.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Add READ_ONCE() when reading rx_errs & tx_drps.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As explained in commit 316580b69d0a ("u64_stats: provide u64_stats_t type")
we should use u64_stats_t and related accessors to avoid load/store tearing.
Add READ_ONCE() when reading rx_errors & tx_dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Netdev reference helpers have a dev_ prefix for historic
reasons. Renaming the old helpers would be too much churn
but we can rename the tracking ones which are relatively
recent and should be the default for new code.
Rename:
dev_hold_track() -> netdev_hold()
dev_put_track() -> netdev_put()
dev_replace_track() -> netdev_ref_replace()
Link: https://lore.kernel.org/r/20220608043955.919359-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
two fixes for panel self-refresh handling, and one to fix
multiple output support on AST.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220609100754.kvrkjy67gqabjuee@houat
|
|
A use-after-free fix for panfrost, and a DT invalid configuration fix for
ti-sn65dsi83
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220526090532.nvhlmwev5qgln3nb@houat
|
|
cros_ec_get_host_event_wake_mask() expects to receive
sizeof(struct ec_response_host_event_mask) from send_command(). The
payload is valid only if the return value is positive.
Return -EPROTO if send_command() returns 0 in
cros_ec_get_host_event_wake_mask().
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-22-tzungbi@kernel.org
|
|
cros_ec_get_host_event_wake_mask() expects to receive
sizeof(struct ec_response_host_event_mask) from send_command().
The payload is valid only if the return value is positive.
Add Kunit tests for returning 0 from send_command() in
cros_ec_get_host_event_wake_mask().
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-21-tzungbi@kernel.org
|
|
cros_ec_get_host_event_wake_mask() used to return value from
send_command() which is number of bytes for input payload on success
(i.e. sizeof(struct ec_response_host_event_mask)).
However, the callers don't need to know how many bytes are available.
Don't return number of available bytes. Instead, return 0 on success;
otherwise, negative integers on error.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-20-tzungbi@kernel.org
|
|
cros_ec_get_host_command_version_mask() expects to receive
sizeof(struct ec_response_get_cmd_versions) from send_command(). The
payload is valid only if the return value is positive.
Return -EPROTO if send_command() returns 0 in
cros_ec_get_host_command_version_mask().
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-19-tzungbi@kernel.org
|
|
cros_ec_get_host_command_version_mask() expects to receive
sizeof(struct ec_response_get_cmd_versions) from send_command().
The payload is valid only if the return value is positive.
Add Kunit tests for returning 0 from send_command() in
cros_ec_get_host_command_version_mask().
Note that because the 2 cros_ec_get_host_command_version_mask() use the
same `ver_mask`. cros_ec_proto_test_query_all_no_host_sleep_return0()
polluates the `ver_mask` and returns 0 on the second send_command() to
make sure the second cros_ec_get_host_command_version_mask() doesn't
take the garbage from the previous call.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-18-tzungbi@kernel.org
|
|
cros_ec_get_host_command_version_mask() should check if EC wasn't happy
by checking `msg->result`.
Use cros_ec_map_error() and return the error code if any.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-17-tzungbi@kernel.org
|
|
cros_ec_query_all() uses cros_ec_get_host_command_version_mask() to
query the supported MKBP version; cros_ec_get_host_command_version_mask()
uses send_command() for transferring the host command.
Returning >=0 from send_command() only denotes the transfer was success.
cros_ec_get_host_command_version_mask() should check if EC wasn't happy
by checking `msg->result`.
Add a Kunit test for returning error in `msg->result` in
cros_ec_get_host_command_version_mask(). For the case,
cros_ec_query_all() should find the EC device doesn't support MKBP.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-16-tzungbi@kernel.org
|
|
cros_ec_get_host_command_version_mask() used to return value from
send_command() which is number of available bytes for input payload on
success (i.e. sizeof(struct ec_response_get_cmd_versions)).
However, the callers don't need to know how many bytes are available.
Don't return number of available bytes. Instead, return 0 on success;
otherwise, negative integers on error.
Also remove the unneeded `ver_mask` initialization as the callers should
take it only if cros_ec_get_host_command_version_mask() returns 0.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-15-tzungbi@kernel.org
|
|
It wrongly showed the following message when it doesn't support MKBP:
"MKBP support version 4294967295".
Fix it.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-14-tzungbi@kernel.org
|
|
cros_ec_get_proto_info_legacy() expects to receive
sizeof(struct ec_response_hello) from send_command(). The payload is
valid only if the return value is positive.
Return -EPROTO if send_command() returns 0 in
cros_ec_get_proto_info_legacy().
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-13-tzungbi@kernel.org
|
|
cros_ec_get_proto_info_legacy() expects to receive
sizeof(struct ec_response_hello) from send_command(). The payload is
valid only if the return value is positive.
Add a Kunit test for returning 0 from send_command() in
cros_ec_get_proto_info_legacy().
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-12-tzungbi@kernel.org
|
|
Rename cros_ec_host_command_proto_query_v2() to
cros_ec_get_proto_info_legacy() and make it responsible for setting
`ec_dev` fields for EC protocol v2.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-11-tzungbi@kernel.org
|
|
cros_ec_get_proto_info() expects to receive
sizeof(struct ec_response_get_protocol_info) from send_command(). The
payload is valid only if the return value is positive.
Return -EPROTO if send_command() returns 0 in cros_ec_get_proto_info().
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-10-tzungbi@kernel.org
|
|
cros_ec_get_proto_info() expects to receive
sizeof(struct ec_response_get_protocol_info) from send_command(). The
payload is valid only if the return value is positive.
Add Kunit tests for returning 0 from send_command() in
cros_ec_get_proto_info().
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-9-tzungbi@kernel.org
|
|
Rename cros_ec_host_command_proto_query() to cros_ec_get_proto_info()
and make it responsible for setting `ec_dev` fields according to the
response protocol info.
Also make cros_ec_get_host_event_wake_mask() allocate its own message
buffer. It was lucky that size of `struct ec_response_host_event_mask`
is less than `struct ec_response_get_protocol_info`. Thus, the buffer
wasn't overflow.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-8-tzungbi@kernel.org
|
|
Use cros_ec_map_error() in cros_ec_get_host_event_wake_mask().
The behavior of cros_ec_get_host_event_wake_mask() slightly changed. It
is acceptable because the caller only needs it returns negative integers
for indicating errors. Especially, the EC_RES_INVALID_COMMAND still
maps to -EOPNOTSUPP.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-7-tzungbi@kernel.org
|
|
send_command() already checks if `ec_dev->pkt_xfer` is NULL. Remove the
redundant check.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-6-tzungbi@kernel.org
|
|
`din_size` is calculated from `ec_dev->max_response`.
`ec_dev->max_response` is further calculated from the protocol info.
To make it clear, assign `din_size` and `dout_size` from protocol info
directly.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-5-tzungbi@kernel.org
|
|
Move passthru indexes for EC and PD devices to common header. Also use
them instead of literal constants.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-4-tzungbi@kernel.org
|
|
cros_ec_query_all() sends multiple host commands to EC for querying
supported protocols and settings.
Add required mock for interacting with cros_ec_query_all() and Kunit
tests.
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Tzung-Bi Shih <tzungbi@kernel.org>
Link: https://lore.kernel.org/r/20220609084957.3684698-3-tzungbi@kernel.org
|