| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
This version brings along the following fixes:
* Changes to DP LT fallback behavior to more closely match the DP standard
* Added new interfaces for lut pipeline
* Restore ref_dtblck value when clk struct is cleared in init_clocks
* Fixes DMUB outbox trace in S4
* Fixes lingering DIO FIFO errors when DIO no longer enabled
* Reads Golden Settings Table from VBIOS
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
It's possible for some fallback scenarios to result in infinite looping
during link training.
[How]
This change modifies DP LT fallback behavior to more closely match the
DP standard. Keep track of the link rate during the EQ_FAIL fallback,
and use it as the maximum link rate for the CR sequence.
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Ilya <Ilya.Bakoulin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Description]
ref_dtbclk value is assigned in clk_mgr_construct,
but the clks struct is cleared in init_clocks.
Make sure to restore the value or we will get
0 value for ref_dtbclk in DCN31.
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DMUB Outbox0 read/write pointer not sync after resumed from S4.
And that caused old traces were sent to outbox.
[How]
Disable DMUB Outbox0 interrupt
and clear DMUB Outbox0 read/write pointer when resumes from S4.
And then enable Outbox0 interrupt before starts DMCUB.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Cruise Hung <Cruise.Hung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
Very low rate to cause memory access issue while resetting
DMCUB after the halt command was sent to it.
The process of stopping fw of DMCUB may be timeout, that means
it is not in idle state, such as the window frames may still be
kept in cache, so reset by force will cause MMHUB hang.
[HOW]
After the halt command was sent, keep checking the DMCUB state until
it is idle.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: hengzhou <Hengyong.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When enabling an HPO stream for the first time after having previously
enabled a DIO stream there may be lingering DIO FIFO errors even though
the DIO is no longer enabled.
These can cause display clock change to hang if we don't apply the
OTG disable workaround since the ramping logic is tied to OTG on.
[How]
The workaround wasn't being applied in the sequence of:
1 DIO stream
0 streams
1 HPO stream
because current_state has no stream or planes in its context - and
it's only swapped after optimize has finished.
We should be using the incoming context instead to determine whether
this logic is needed or not.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
why and how:
Revert this change. It was causing a black screen with certain blocks
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leung, Martin <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Dmub read AUX_DPHY_RX_CONTROL0 from Golden Setting Table,
but driver will set it to default value 0x103d1110, which
causes issue in some case
[How]
Remove the driver code, use the value set by dmub in
dp_aux_init
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Sherry Wang <YAO.WANG1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Pull pwm updates from Thierry Reding:
"Quite a large number of conversions this time around, courtesy of Uwe
who has been working tirelessly on these. No drivers of the legacy API
are left at this point, so as a next step the old API can be removed.
Support is added for a few new devices such as the Xilinx AXI timer-
based PWMs and the PWM IP found on Sunplus SoCs.
Other than that, there's a number of fixes, cleanups and optimizations"
* tag 'pwm/for-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (43 commits)
pwm: pwm-cros-ec: Add channel type support
dt-bindings: google,cros-ec-pwm: Add the new -type compatible
dt-bindings: Add mfd/cros_ec definitions
pwm: Document that the pinstate of a disabled PWM isn't reliable
pwm: twl-led: Implement .apply() callback
pwm: lpc18xx: Implement .apply() callback
pwm: mediatek: Implement .apply() callback
pwm: lpc32xx: Implement .apply() callback
pwm: tegra: Implement .apply() callback
pwm: stmpe: Implement .apply() callback
pwm: sti: Implement .apply() callback
pwm: pwm-mediatek: Add support for MediaTek Helio X10 MT6795
dt-bindings: pwm: pwm-mediatek: Add documentation for MT6795 SoC
pwm: tegra: Optimize period calculation
pwm: renesas-tpu: Improve precision of period and duty_cycle calculation
pwm: renesas-tpu: Improve maths to compute register settings
pwm: renesas-tpu: Rename variables to match the usual naming
pwm: renesas-tpu: Implement .apply() callback
pwm: renesas-tpu: Make use of devm functions
pwm: renesas-tpu: Make use of dev_err_probe()
...
|
|
Pull rpmsg updates from Bjorn Andersson:
"This corrects the check for irq_of_parse_and_map() failures in the
Qualcomm SMD driver and fixes unregistration and a couple of double
free in the virtio rpmsg driver"
* tag 'rpmsg-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux:
rpmsg: qcom_smd: Fix returning 0 if irq_of_parse_and_map() fails
rpmsg: virtio: Fix the unregistration of the device rpmsg_ctrl
rpmsg: virtio: Fix possible double free in rpmsg_virtio_add_ctrl_dev()
rpmsg: virtio: Fix possible double free in rpmsg_probe()
rpmsg: qcom_smd: Fix irq_of_parse_and_map() return value
|
|
Pull remoteproc updates from Bjorn Andersson:
"This fixes a race condition in the user space interface for starting
and stopping remote processors, it makes the ELF loader properly skip
zero memsz segments and it cleans up the debugfs tracefile code a bit
by not checking for errors.
It introduces support for controlling the audio DSP on Qualcomm
MSM8226, as well as audio and compute DSPs on Qualcomm SC8280XP.
It makes it possible to specify the firmware path for Mediatek's
remote processors, fixes a double free in the SCP driver and addresses
an issue with the SRAM initialization on MT8195.
Lastly it deprecates the custom ELF loader in the iMX remoteproc
driver, in favor of using the shared one"
* tag 'rproc-v5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/remoteproc/linux: (21 commits)
dt-bindings: remoteproc: mediatek: Add optional memory-region to mtk,scp
dt-bindings: remoteproc: mediatek: Make l1tcm reg exclusive to mt819x
dt-bindings: remoteproc: st,stm32-rproc: Fix phandle-array parameters description
remoteproc: imx_rproc: Support i.MX93
dt-bindings: remoteproc: imx_rproc: Support i.MX93
remoteproc: qcom: pas: Add MSM8226 ADSP support
dt-bindings: remoteproc: qcom: pas: Add MSM8226 adsp
remoteproc: mediatek: Allow reading firmware-name from DT
dt-bindings: remoteproc: mediatek: Add firmware-name property
remoteproc: qcom: pas: Add sc8280xp remoteprocs
dt-bindings: remoteproc: qcom: pas: Add sc8280xp adsp and nsp pair
dt-bindings: remoteproc: mediatek: Add interrupts property to mtk,scp
remoteproc: imx_rproc: Ignore create mem entry for resource table
remoteproc: core: Move state checking to remoteproc_core
remoteproc: core: Remove state checking before calling rproc_boot()
remoteproc: imx_dsp_rproc: Make rsc_table optional
remoteproc: imx_dsp_rproc: use common rproc_elf_load_segments
remoteproc: elf_loader: skip segment with memsz as zero
remoteproc: mtk_scp: Fix a potential double free
remoteproc: Don't bother checking the return value of debugfs_create*
...
|
|
Pull spi fixes from Mark Brown:
"A couple of fixes that came in during the merge window: a driver fix
for spurious timeouts in the fsi driver and an improvement to make the
core display error messages for transfer_one_message() to help people
debug things"
* tag 'spi-fix-v5.19-rc0' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: core: Display return code when failing to transfer message
spi: fsi: Fix spurious timeout
|
|
Pull pcmcia updates from Dominik Brodowski:
"A few odd cleanups and fixes, including a Kconfig fix to add a
required dependency on MIPS"
* 'pcmcia-next' of git://git.kernel.org/pub/scm/linux/kernel/git/brodo/linux:
pcmcia: Use platform_get_irq() to get the interrupt
pcmcia: db1xxx_ss: restrict to MIPS_DB1XXX boards
drivers/pcmcia: Fix typo in comment
|
|
For regcache_sync_region, need to use pca953x_recalc_addr() to get
the real register address.
Fixes: b76574300504 ("gpio: pca953x: Restore registers after suspend/resume cycle")
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Some machines declare DRRS type = seamless, DRRS = no, DMRRS = yes.
I *think* DMRRS stands for "dynamcic media refresh rate", and
I suspect the way it's meant to work is that it lets the driver
switch refresh rates to match the frame rate for media playback.
Obviously for us all that kind of policy stuff is entirely up to
userspace, so the only thing we may do is make the extra refresh
rate(s) available.
So let's treat this case as just static DRRS for now. In the
future We might want to differentiate the "seamless w/ downclocking"
vs. "seamless w/o downclocking" cases so that we could do seamless
refresh rate changes for systems that only claim to support DMRRS.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/125
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-7-ville.syrjala@linux.intel.com
|
|
Add a bunch of new struff we're missing in various BDB blocks.
TODO: Bunch of these might actually need to be taken
into use...
v2: s/lfp_features/lfp_power/features/ (Jani)
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-6-ville.syrjala@linux.intel.com
|
|
Fix various typos around "aggressiveness". Note that
the VBT spec also sometimes missspells it as
"agressiveness" so I guess that's where some of the typos
came from.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-5-ville.syrjala@linux.intel.com
|
|
It seem that when dealing with VRR capable eDP panels we need
to accept fixed modes with variable vblank length (which is what
VRR varies dynamically). Typically the preferred mode seems to be
a non-VRR more (lowish dotclock/refresh rate + short vblank).
We also have examples where it looks like even the hblank length
is a bit different between the preferred mode vs. VRR mode(s).
So let's just accept anything that has matching hdisp+vdisp+flags.
v2: Document that is_alt_drrs_mode() is a subset of is_alt_vrr_mode() (Jani)
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/125
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-4-ville.syrjala@linux.intel.com
|
|
To help with debugging DRRS/VRR panel init let's dump out all
the fixed modes we rejected for whatever reason.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-3-ville.syrjala@linux.intel.com
|
|
VBT seems to have an extra flag for VRR vs. not. Let's consult
that for eDP panels.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-2-ville.syrjala@linux.intel.com
|
|
The intention of the use of mmc_blk_reset_success() in
mmc_blk_cqe_recovery() was to prevent repeated resets when retrying and
getting the same error. However, that may not be the case - any amount
of time and I/O may pass before another recovery is needed, in which
case there would be no reason to deny it the opportunity to recover via
a reset if necessary. CQE recovery is expected seldom and failure to
recover (if the clear tasks command fails), even more seldom, so it is
better to allow the reset always, which can be done by calling
mmc_blk_reset_success() always.
Fixes: 1e8e55b67030c6 ("mmc: block: Add CQE support")
Cc: stable@vger.kernel.org
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Link: https://lore.kernel.org/r/20220531171922.76080-1-adrian.hunter@intel.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Geert reports that the new option CONFIG_EFI_DISABLE_RUNTIME is user
visible even when EFI support is disabled, which is unnecessary and
clutters the Kconfig interface.
So let's move this option into the existing Kconfig submenu that already
depends on CONFIG_EFI, and while at it, give some other options the same
treatment.
Also clean up a small wart where the efi/ subdirectory is listed twice.
Let's just list it unconditionally so that both EFI and UEFI_CPER based
pieces will be built independently (the latter only depends on the
former on !X86)
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
The newly added DXE calls use 64-bit quantities, which means we need to
marshall them explicitly when running in mixed mode. Currently, we get
away without it because we just bail when GetMemorySpaceDescriptor()
fails, which is guaranteed to happen due to the function argument mixup.
Let's fix this properly, though, by defining the macros that describe
how to marshall the arguments. While at it, drop an incorrect cast on a
status variable.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Create a new macsec device but not get reference to real_dev. That can
not ensure that real_dev is freed after macsec. That will trigger the
UAF bug for real_dev as following:
==================================================================
BUG: KASAN: use-after-free in macsec_get_iflink+0x5f/0x70 drivers/net/macsec.c:3662
Call Trace:
...
macsec_get_iflink+0x5f/0x70 drivers/net/macsec.c:3662
dev_get_iflink+0x73/0xe0 net/core/dev.c:637
default_operstate net/core/link_watch.c:42 [inline]
rfc2863_policy+0x233/0x2d0 net/core/link_watch.c:54
linkwatch_do_dev+0x2a/0x150 net/core/link_watch.c:161
Allocated by task 22209:
...
alloc_netdev_mqs+0x98/0x1100 net/core/dev.c:10549
rtnl_create_link+0x9d7/0xc00 net/core/rtnetlink.c:3235
veth_newlink+0x20e/0xa90 drivers/net/veth.c:1748
Freed by task 8:
...
kfree+0xd6/0x4d0 mm/slub.c:4552
kvfree+0x42/0x50 mm/util.c:615
device_release+0x9f/0x240 drivers/base/core.c:2229
kobject_cleanup lib/kobject.c:673 [inline]
kobject_release lib/kobject.c:704 [inline]
kref_put include/linux/kref.h:65 [inline]
kobject_put+0x1c8/0x540 lib/kobject.c:721
netdev_run_todo+0x72e/0x10b0 net/core/dev.c:10327
After commit faab39f63c1f ("net: allow out-of-order netdev unregistration")
and commit e5f80fcf869a ("ipv6: give an IPv6 dev to blackhole_netdev"), we
can add dev_hold_track() in macsec_dev_init() and dev_put_track() in
macsec_free_netdev() to fix the problem.
Fixes: 2bce1ebed17d ("macsec: fix refcnt leak in module exit routine")
Reported-by: syzbot+d0e94b65ac259c29ce7a@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/r/20220531074500.1272846-1-william.xuanziyang@huawei.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The context bus is a "dummy" bus that contains struct devices that
correspond to IOMMU contexts assigned through Host1x to processes.
Even when host1x itself is built as a module, the bus is registered
in built-in code so that the built-in ARM SMMU driver is able to
reference it.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The is_valid_offset() function returns success/true if the call to
validate_and_get_cpt_blkaddr() fails.
Fixes: ecad2ce8c48f ("octeontx2-af: cn10k: Add mailbox to configure reassembly timeout")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/YpXDrTPb8qV01JSP@kili
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Avoid bringing the entire machine down even if there's a bug that
shouldn't happen, but won't corrupt the system either. Log them loudly
and limp on.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531162527.1062319-1-jani.nikula@intel.com
|
|
Guard ns_targets in struct bond_params by CONFIG_IPV6, which could save
256 bytes if IPv6 not configed. Also add this protection for function
bond_is_ip6_target_ok() and bond_get_targets_ip6().
Remove the IS_ENABLED() check for bond_opts[] as this will make
BOND_OPT_NS_TARGETS uninitialized if CONFIG_IPV6 not enabled. Add
a dummy bond_option_ns_ip6_targets_set() for this situation.
Fixes: 4e24be018eb9 ("bonding: add new parameter ns_targets")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Link: https://lore.kernel.org/r/20220531063727.224043-1-liuhangbin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
We should set the pci driver data in probe instead of the vdpa device
adding callback. Otherwise if no vDPA device is created we will lose
the pointer to the management device.
Fixes: 6b5df347c6482 ("vDPA/ifcvf: implement management netlink framework for ifcvf")
Tested-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Message-Id: <20220524055557.1938-1-jasowang@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Support HW offloaded filtering of MAC/VLAN packets.
To allow that, we add a handler to handle VLAN configurations coming
through the control VQ. Two operations are supported.
1. Adding VLAN - in this case, an entry will be added to the RX flow
table that will allow the combination of the MAC/VLAN to be
forwarded to the TIR.
2. Removing VLAN - will remove the entry from the flow table,
effectively blocking such packets from going through.
Currently the control VQ does not propagate changes to the MAC of the
VLAN device so we always use the MAC of the parent device.
Examples:
1. Create vlan device:
$ ip link add link ens1 name ens1.8 type vlan id 8
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20220411122942.225717-4-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
The flow counter has been introduced in early versions of the driver to
aid in debugging. It is no longer needed and can harm performance.
Remove it.
Signed-off-by: Eli Cohen <elic@nvidia.com>
Message-Id: <20220411122942.225717-2-elic@nvidia.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
xen_remap() is used to establish mappings for frames not under direct
control of the kernel: for Xenstore and console ring pages, and for
grant pages of non-PV guests.
Today xen_remap() is defined to use ioremap() on x86 (doing uncached
mappings), and ioremap_cache() on Arm (doing cached mappings).
Uncached mappings for those use cases are bad for performance, so they
should be avoided if possible. As all use cases of xen_remap() don't
require uncached mappings (the mapped area is always physical RAM),
a mapping using the standard WB cache mode is fine.
As sparse is flagging some of the xen_remap() use cases to be not
appropriate for iomem(), as the result is not annotated with the
__iomem modifier, eliminate xen_remap() completely and replace all
use cases with memremap() specifying the MEMREMAP_WB caching mode.
xen_unmap() can be replaced with memunmap().
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Acked-by: Stefano Stabellini <sstabellini@kernel.org>
Link: https://lore.kernel.org/r/20220530082634.6339-1-jgross@suse.com
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
As the second and last step of preparation to add support for more
PMICs in this driver, move the long press debounce mask to struct
mtk_pmic_regs and use that in mtk_pmic_keys_lp_reset_setup() instead
of directly using the definition.
While at it, remove the definition for MTK_PMIC_RST_DU_SHIFT as we
are able to calculate it dynamically and spares us some unnecessary
new definitions around for future per-PMIC variations of RST_DU_MASK.
Lastly, it was necessary to change the function signature of
mtk_pmic_keys_lp_reset_setup() to now pass a pointer to the main
mtk_pmic_regs structure, since that's where the reset debounce
mask now resides.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220524093505.85438-3-angelogioacchino.delregno@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Place the key bit in struct mtk_pmic_keys_regs to enhance this
driver's flexibility, in preparation for adding support for more
PMICs.
While at it, remove the definition of MTK_PMIC_RST_KEY_MASK as
we are now dynamically setting the keymask relatively to the keys
that are defined in the newly added rst_en_mask variable, on a
per-key basis.
This commit brings no functional changes.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/20220524093505.85438-2-angelogioacchino.delregno@collabora.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of doing 3 read-modify-write operations when configuring behavior
of long-press, consolidate everything into one.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com> # on mt8183-pumpkin
Link: https://lore.kernel.org/r/YowH0Q5HAGU7Grx2@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
There are no hard architecture dependencies in the driver, so to improve
compile test coverage let's enable the driver when COMPILE_TEST is
selected.
Reviewed-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Link: https://lore.kernel.org/r/YowG7BVsJTNd0ELi@google.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Bspec: 64027
Signed-off-by: Stuart Summers <stuart.summers@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220527163348.1936146-3-matthew.d.roper@intel.com
|
|
For PVC, the base die and compute tile have separate stepping values
that we need to track; we'll use the existing graphics_step field to
represent the compute tile stepping and add a new 'basedie_step' field.
Unlike past platforms, steppings for these components are represented by
specific bitfields within the PCI revision ID, and we shouldn't make
assumptions about the non-CT, non-BD bits staying 0. Let's update our
stepping code accordingly.
Bspec: 44484
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Matt Atwood <matthew.s.atwood@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220527163348.1936146-2-matthew.d.roper@intel.com
|
|
Pull LED updates from Pavel Machek:
"Most significant here is the driver for Qualcomm LPG. Apparently it
drives backlight on some boards, so it is quite important for some
people"
* tag 'leds-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds:
leds: qcom-lpg: Require pattern to follow documentation
leds: lp50xx: Remove duplicated error reporting in .remove()
leds: qcom-lpg: add missing PWM dependency
leds: ktd2692: Make aux-gpios optional
dt-bindings: leds: convert ktd2692 bindings to yaml
leds: ktd2692: Avoid duplicate error messages on probe deferral
leds: is31fl32xx: Improve error reporting in .remove()
leds: Move pwm-multicolor driver into rgb directory
leds: Add PWM multicolor driver
dt-bindings: leds: Add multicolor PWM LED bindings
dt-bindings: leds: Optional multi-led unit address
leds: regulator: Make probeable from device tree
leds: regulator: Add dev helper variable
dt-bindings: leds: Add regulator-led binding
leds: pca9532: Make pca9532_destroy_devices() return void
leds: Add pm8350c support to Qualcomm LPG driver
dt-bindings: leds: Add pm8350c pmic support
leds: Add driver for Qualcomm LPG
dt-bindings: leds: Add Qualcomm Light Pulse Generator binding
|
|
Pull i2c updates from Wolfram Sang:
"Only driver updates for 5.19.
Bigger changes are for Meson, NPCM, and R-Car, but there are also
changes all over the place"
* tag 'i2c-for-5.19' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (34 commits)
i2c: meson: fix typo in comment
i2c: rcar: use flags instead of atomic_xfer
i2c: rcar: REP_AFTER_RD is not a persistent flag
i2c: rcar: use BIT macro consistently
i2c: qcom-geni: remove unnecessary conditions
i2c: mt7621: Use devm_platform_get_and_ioremap_resource()
i2c: rcar: refactor handling of first message
i2c: rcar: avoid race condition with SMIs
i2c: xiic: Correct the datatype for rx_watermark
i2c: rcar: fix PM ref counts in probe error paths
i2c: npcm: Handle spurious interrupts
i2c: npcm: Correct register access width
i2c: npcm: Add tx complete counter
i2c: npcm: Fix timeout calculation
i2c: npcm: Remove unused variable clk_regmap
i2c: npcm: Change the way of getting GCR regmap
i2c: xiic: Fix Tx Interrupt path for grouped messages
i2c: xiic: Fix coding style issues
i2c: xiic: return value of xiic_reinit
i2c: cadence: Increase timeout per message if necessary
...
|
|
Since JOYSTICK_SENSEHAT selects MFD_SIMPLE_MFD_I2C and the latter
depends on HAS_IOMEM, and since 'select' does not follow any
dependency chains, JOYSTICK_SENSEHAT should also depend on HAS_IOMEM
to prevent a kconfig warning and a build error:
WARNING: unmet direct dependencies detected for MFD_SIMPLE_MFD_I2C
Depends on [n]: HAS_IOMEM [=n] && I2C [=y]
Selected by [y]:
- JOYSTICK_SENSEHAT [=y] && INPUT_JOYSTICK [=y] && INPUT [=y] && I2C [=y]
s390-linux-ld: drivers/mfd/simple-mfd-i2c.o: in function `simple_mfd_i2c_probe':
simple-mfd-i2c.c:(.text+0xc8): undefined reference to `devm_mfd_add_devices'
Fixes: 41657514c796 ("Input: add Raspberry Pi Sense HAT joystick driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220531022942.16340-1-rdunlap@infradead.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
I2C core will set up device as a wakeup source and will configure interrupt
as a wakeup interrupt if client is created with I2C_CLIENT_WAKE flag. Let's
rely on this facility and to not unconditionally set up the device as
wakeup device in the driver.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220528045631.289821-4-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This simplifies error handling in probe() and reduces amount of explicit
code in remove().
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220528045631.289821-3-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Instead of using hard interrupt handler and manually scheduling work
item to handle I2C communications, let's switch to threaded interrupt
handling.
While at that enforce the readout delay required on pre- revision 4
silicon.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220528045631.289821-2-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
To improve compile-time coverage let's drop #ifdef CONFIG_PM guards
and use SIMPLE_DEV_PM_OPS and __maybe_unused attributes and rely on
the linker to drop unused code.
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Link: https://lore.kernel.org/r/20220528045631.289821-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
In some use-cases, mlx5 instances will need to search for their peer
device (the other port on the same HCA). For that, mlx5 device matching
mechanism relied on auxiliary_find_device() to search, and used a bad matching
callback function.
This approach has two issues:
1) next_phys_dev() the matching function, assumed all devices are
of the type mlx5_adev (mlx5 auxiliary device) which is wrong and
could lead to crashes, this worked for a while, since only lately
other drivers started registering auxiliary devices.
2) using the auxiliary class bus (auxiliary_find_device) to search for
mlx5_core_dev devices, who are actually PCIe device instances, is wrong.
This works since mlx5_core always has at least one mlx5_adev instance
hanging around in the aux bus.
As suggested by others we can fix 1. by comparing device names prefixes
if they have the string "mlx5_core" in them, which is not a best practice !
but even with that fixed, still 2. needs fixing, we are trying to
match pcie device peers so we should look in the right bus (pci bus),
hence this fix.
The fix:
1) search the pci bus for mlx5 peer devices, instead of the aux bus
2) to validated devices are the same type "mlx5_core_dev" compare if
they have the same driver, which is bulletproof.
This wouldn't have worked with the aux bus since the various mlx5 aux
device types don't share the same driver, even if they share the same device
wrapper struct (mlx5_adev) "which helped to find the parent device"
Fixes: a925b5e309c9 ("net/mlx5: Register mlx5 devices to auxiliary virtual bus")
Reported-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Reported-by: Maher Sanalla <msanalla@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Reviewed-by: Maher Sanalla <msanalla@nvidia.com>
|
|
Some features (LRO, HW GRO) conflict with XDP. If there is an attempt to
enable such features while XDP is active, they will be set to `off
[requested on]`. In order to activate these features after XDP is turned
off, the driver needs to call netdev_update_features(). This commit adds
this missing call after XDP state changes.
Fixes: cf6e34c8c22f ("net/mlx5e: Properly block LRO when XDP is enabled")
Fixes: b0617e7b3500 ("net/mlx5e: Properly block HW GRO when XDP is enabled")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When the driver activates the channels, it assumes NAPI isn't running
yet. mlx5e_activate_rq posts a NOP WQE to ICOSQ to trigger a hardware
interrupt and start NAPI, which will run mlx5e_alloc_rx_mpwqe and post
UMR WQEs to ICOSQ to be able to receive packets with striding RQ.
Unfortunately, a race condition is possible if NAPI is triggered by
something else (for example, TX) at a bad timing, before
mlx5e_activate_rq finishes. In this case, mlx5e_alloc_rx_mpwqe may post
UMR WQEs to ICOSQ, and with the bad timing, the wqe_info of the first
UMR may be overwritten by the wqe_info of the NOP posted by
mlx5e_activate_rq.
The consequence is that icosq->db.wqe_info[0].num_wqebbs will be changed
from MLX5E_UMR_WQEBBS to 1, disrupting the integrity of the array-based
linked list in wqe_info[]. mlx5e_poll_ico_cq will hang in an infinite
loop after processing wqe_info[0], because after the corruption, the
next item to be processed will be wqe_info[1], which is filled with
zeros, and `sqcc += wi->num_wqebbs` will never move further.
This commit fixes this race condition by using async_icosq to post the
NOP and trigger the interrupt. async_icosq is always protected with a
spinlock, eliminating the race condition.
Fixes: bc77b240b3c5 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reported-by: Karsten Nielsen <karsten@foo-bar.dk>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Tuple entries that don't have nat configured for them
which are added to the ct nat table will always create
a new modify header, as we don't check for possible
re-use on them. The same for tuples that have nat configured
for them but are added to ct table.
Fix the above by only avoiding wasteful re-use lookup
for actually natted entries in ct nat table.
Fixes: 7fac5c2eced3 ("net/mlx5: CT: Avoid reusing modify header context for natted entries")
Signed-off-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The cited commit changed promisc table to be created on demand with the
highest priority in the NIC table replacing the vlan table, this caused
tc NIC tables miss flow to skip the prmoisc table because it use vlan
table as miss table.
OVS offload in NIC mode use promisc by default so any unicast packet
which will be handled by tc NIC tables miss flow will skip the promisc
rule and will be dropped.
Fix this by adding new empty table in new tc level with low priority and
point the nic tc chain miss to it, the new table is managed so it will
point to vlan table if promisc is disabled and to promisc table if enabled.
Fixes: 1c46d7409f30 ("net/mlx5e: Optimize promiscuous mode")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Paul Blakey <paulb@nvidia.com>
Reviewed-by: Ariel Levkovich <lariel@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
Aric Cyr
Ilya
Alvin
Hung, Cruise
hengzhou
Nicholas Kazlauskas
Leung, Martin
Sherry Wang
Linus Torvalds
Haibo Chen
Ville Syrjälä
Adrian Hunter
Ard Biesheuvel
Ziyang Xuan
Mikko Perttunen
Dan Carpenter
Jani Nikula
Hangbin Liu
Jason Wang
Eli Cohen
Juergen Gross
AngeloGioacchino Del Regno
Dmitry Torokhov
Stuart Summers
Matt Roper
Randy Dunlap
Saeed Mahameed
Maxim Mikityanskiy
Paul Blakey
Maor Dickman