| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Current kernel reports that BARs larger than 128GB, e.g., this 4TB BAR, are
disabled:
pci 0000:01:00.0: disabling BAR 4: [mem 0x00000000-0x3ffffffffff 64bit pref] (bad alignment 0x40000000000)
Increase the maximum BAR size from 128GB to 8TB for future expansion.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220118092117.10089-1-liudongdong3@huawei.com
Signed-off-by: Dongdong Liu <liudongdong3@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
ZONE_DEVICE struct pages have an extra reference count that complicates
the code for put_page() and several places in the kernel that need to
check the reference count to see that a page is not being used (gup,
compaction, migration, etc.). Clean up the code so the reference count
doesn't need to be treated specially for ZONE_DEVICE pages.
Note that this excludes the special idle page wakeup for fsdax pages,
which still happens at refcount 1. This is a separate issue and will
be sorted out later. Given that only fsdax pages require the
notifiacation when the refcount hits 1 now, the PAGEMAP_OPS Kconfig
symbol can go away and be replaced with a FS_DAX check for this hook
in the put_page fastpath.
Based on an earlier patch from Ralph Campbell <rcampbell@nvidia.com>.
Link: https://lkml.kernel.org/r/20220210072828.2930359-8-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Ralph Campbell <rcampbell@nvidia.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Tested-by: "Sierra Guiza, Alejandro (Alex)" <alex.sierra@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Christian Knig <christian.koenig@amd.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
Move the check for the actual pgmap types that need the free at refcount
one behavior into the out of line helper, and thus avoid the need to
pull memremap.h into mm.h.
Link: https://lkml.kernel.org/r/20220210072828.2930359-7-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Felix Kuehling <Felix.Kuehling@amd.com>
Tested-by: "Sierra Guiza, Alejandro (Alex)" <alex.sierra@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Chaitanya Kulkarni <kch@nvidia.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
hmm.h pulls in the world for no good reason at all. Remove the
includes and push a few ones into the users instead.
Link: https://lkml.kernel.org/r/20220210072828.2930359-4-hch@lst.de
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Reviewed-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Muchun Song <songmuchun@bytedance.com>
Tested-by: "Sierra Guiza, Alejandro (Alex)" <alex.sierra@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Alistair Popple <apopple@nvidia.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Christian Knig <christian.koenig@amd.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Felix Kuehling <Felix.Kuehling@amd.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Miaohe Lin <linmiaohe@huawei.com>
Cc: "Pan, Xinhui" <Xinhui.Pan@amd.com>
Cc: Ralph Campbell <rcampbell@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Matthew Wilcox (Oracle) <willy@infradead.org>
|
|
|
|
The ice_for_each_vf macro is intended to be used to loop over all VFs.
The current implementation relies on an iterator that is the index into
the VF array in the PF structure. This forces all users to perform a
look up themselves.
This abstraction forces a lot of duplicate work on callers and leaks the
interface implementation to the caller. Replace this with an
implementation that includes the VF pointer the primary iterator. This
version simplifies callers which just want to iterate over every VF, as
they no longer need to perform their own lookup.
The "i" iterator value is replaced with a new unsigned int "bkt"
parameter, as this will match the necessary interface for replacing
the VF array with a hash table. For now, the bkt is the VF ID, but in
the future it will simply be the hash bucket index. Document that it
should not be treated as a VF ID.
This change aims to simplify switching from the array to a hash table. I
considered alternative implementations such as an xarray but decided
that the hash table was the simplest and most suitable implementation. I
also looked at methods to hide the bkt iterator entirely, but I couldn't
come up with a feasible solution that worked for hash table iterators.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When removing VFs, the driver takes a weird approach of assigning
pf->num_alloc_vfs to 0 before iterating over the VFs using a temporary
variable.
This logic has been in the driver for a long time, and seems to have
been carried forward from i40e.
We want to refactor the way VFs are stored, and iterating over the data
structure without the ice_for_each_vf interface impedes this work.
The logic relies on implicitly using the num_alloc_vfs as a sort of
"safe guard" for accessing VF data.
While this sort of guard makes sense for Single Root IOV where all VFs
are added at once, the data structures don't work for VFs which can be
added and removed dynamically. We also have a separate state flag,
ICE_VF_DEINIT_IN_PROGRESS which is a stronger protection against
concurrent removal and access.
Avoid the custom tmp iteration and replace it with the standard
ice_for_each_vf iterator. Delay the assignment of num_alloc_vfs until
after this loop finishes.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_vc_send_msg_to_vf function is used by the PF to send a response
to a VF. This function has overzealous checks to ensure its not passed a
NULL VF pointer and to ensure that the passed in struct ice_vf has a
valid vf_id sub-member.
These checks have existed since commit 1071a8358a28 ("ice: Implement
virtchnl commands for AVF support") and function as simple sanity
checks.
We are planning to refactor the ice driver to use a hash table along
with appropriate locks in a future refactor. This change will modify how
the ice_validate_vf_id function works. Instead of a simple >= check to
ensure the VF ID is between some range, it will check the hash table to
see if the specified VF ID is actually in the table. This requires that
the function properly lock the table to prevent race conditions.
The checks may seem ok at first glance, but they don't really provide
much benefit.
In order for ice_vc_send_msg_to_vf to have these checks fail, the
callers must either (1) pass NULL as the VF, (2) construct an invalid VF
pointer manually, or (3) be using a VF pointer which becomes invalid
after they obtain it properly using ice_get_vf_by_id.
For (1), a cursory glance over callers of ice_vc_send_msg_to_vf can show
that in most cases the functions already operate assuming their VF
pointer is valid, such as by derferencing vf->pf or other members.
They obtain the VF pointer by accessing the VF array using the VF ID,
which can never produce a NULL value (since its a simple address
operation on the array it will not be NULL.
The sole exception for (1) is that ice_vc_process_vf_msg will forward a
NULL VF pointer to this function as part of its goto error handler
logic. This requires some minor cleanup to simply exit immediately when
an invalid VF ID is detected (Rather than use the same error flow as
the rest of the function).
For (2), it is unexpected for a flow to construct a VF pointer manually
instead of accessing the VF array. Defending against this is likely to
just hide bad programming.
For (3), it is definitely true that VF pointers could become invalid,
for example if a thread is processing a VF message while the VF gets
removed. However, the correct solution is not to add additional checks
like this which do not guarantee to prevent the race. Instead we plan to
solve the root of the problem by preventing the possibility entirely.
This solution will require the change to a hash table with proper
locking and reference counts of the VF structures. When this is done,
ice_validate_vf_id will require locking of the hash table. This will be
problematic because all of the callers of ice_vc_send_msg_to_vf will
already have to take the lock to obtain the VF pointer anyways. With a
mutex, this leads to a double lock that could hang the kernel thread.
Avoid this by removing the checks which don't provide much value, so
that we can safely add the necessary protections properly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
After removing all VFs, the driver clears the VFLR indication for VFs.
This has been in ice since the beginning of SR-IOV support in the ice
driver.
The implementation was copied from i40e, and the motivation for the VFLR
indication clearing is described in the commit f7414531a0cf ("i40e:
acknowledge VFLR when disabling SR-IOV")
The commit explains that we need to clear the VFLR indication because
the virtual function undergoes a VFLR event. If we don't indicate that
it is complete it can cause an issue when VFs are re-enabled due to
a "phantom" VFLR.
The register block read was added under a pci_vfs_assigned check
originally. This was done because we added the check after calling
pci_disable_sriov. This was later moved to disable SRIOV earlier in the
flow so that the VF drivers could be torn down before we removed
functionality.
Move the VFLR acknowledge into the main loop that tears down VF
resources. This avoids using the tmp value for iterating over VFs
multiple times. The result will make it easier to refactor the VF array
in a future change.
It's possible we might want to modify this flow to also stop checking
pci_vfs_assigned. However, it seems reasonable to keep this change: we
should only clear the VFLR if we actually disabled SR-IOV.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_mbx_clear_malvf function is used to clear the indication and
count of how many times a VF was detected as malicious. During
ice_free_vfs, we use this function to ensure that all removed VFs are
reset to a clean state.
The call currently is done at the end of ice_free_vfs() using a tmp
value to iterate over all of the entries in the bitmap.
This separate iteration using tmp is problematic for a planned refactor
of the VF array data structure. To avoid this, lets move the call
slightly higher into the function inside the loop where we teardown all
of the VFs. This avoids one use of the tmp value used for iteration.
We'll fix the other user in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We are planning to replace the simple array structure tracking VFs with
a hash table. This change will also remove the "num_alloc_vfs" variable.
Instead, new access functions to use the hash table as the source of
truth will be introduced. These will generally be equivalent to existing
checks, except during VF initialization.
Specifically, ice_set_per_vf_res() cannot use the hash table as it will
be operating prior to VF structures being inserted into the hash table.
Instead of using pf->num_alloc_vfs, simply pass the num_vfs value in
from the caller.
Note that a sub-function of ice_set_per_vf_res, ice_determine_res, also
implicitly depends on pf->num_alloc_vfs. Replace ice_determine_res with
a simpler inline implementation based on rounddown_pow_of_two. Note that
we must explicitly check that the argument is non-zero since it does not
play well with zero as a value.
Instead of using the function and while loop, simply calculate the
number of queues we have available by dividing by num_vfs. Check if the
desired queues are available. If not, round down to the nearest power of
2 that fits within our available queues.
This matches the behavior of ice_determine_res but is easier to follow
as simple in-line logic. Remove ice_determine_res entirely.
With this change, we no longer depend on the pf->num_alloc_vfs during
the initialization phase of VFs. This will allow us to safely remove it
in a future planned refactor of the VF data structures.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The VSI structure contains a vf_id field used to associate a VSI with a
VF. This is used mainly for ICE_VSI_VF as well as partially for
ICE_VSI_CTRL associated with the VFs.
This API was designed with the idea that VFs are stored in a simple
array that was expected to be static throughout most of the driver's
life.
We plan on refactoring VF storage in a few key ways:
1) converting from a simple static array to a hash table
2) using krefs to track VF references obtained from the hash table
3) use RCU to delay release of VF memory until after all references
are dropped
This is motivated by the goal to ensure that the lifetime of VF
structures is accounted for, and prevent various use-after-free bugs.
With the existing vsi->vf_id, the reference tracking for VFs would
become somewhat convoluted, because each VSI maintains a vf_id field
which will then require performing a look up. This means all these flows
will require reference tracking and proper usage of rcu_read_lock, etc.
We know that the VF VSI will always be backed by a valid VF structure,
because the VSI is created during VF initialization and removed before
the VF is destroyed. Rely on this and store a reference to the VF in the
VSI structure instead of storing a VF ID. This will simplify the usage
and avoid the need to perform lookups on the hash table in the future.
For ICE_VSI_VF, it is expected that vsi->vf is always non-NULL after
ice_vsi_alloc succeeds. Because of this, use WARN_ON when checking if a
vsi->vf pointer is valid when dealing with VF VSIs. This will aid in
debugging code which violates this assumption and avoid more disastrous
panics.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The code for supporting eswitch mode and port representors on VFs uses
an unwind based cleanup flow when handling errors.
These flows are used to cleanup and get everything back to the state
prior to attempting to switch from legacy to representor mode or back.
The unwind iterations make sense, but complicate a plan to refactor the
VF array structure. In the future we won't have a clean method of
reversing an iteration of the VFs.
Instead, we can change the cleanup flow to just iterate over all VF
structures and clean up appropriately.
First notice that ice_repr_add_for_all_vfs and ice_repr_rem_from_all_vfs
have an additional step of re-assigning the VC ops. There is no good
reason to do this outside of ice_repr_add and ice_repr_rem. It can
simply be done as the last step of these functions.
Second, make sure ice_repr_rem is safe to call on a VF which does not
have a representor. Check if vf->repr is NULL first and exit early if
so.
Move ice_repr_rem_from_all_vfs above ice_repr_add_for_all_vfs so that we
can call it from the cleanup function.
In ice_eswitch.c, replace the unwind iteration with a call to
ice_eswitch_release_reprs. This will go through all of the VFs and
revert the VF back to the standard model without the eswitch mode.
To make this safe, ensure this function checks whether or not the
represent or has been moved. Rely on the metadata destination in
vf->repr->dst. This must be NULL if the representor has not been moved
to eswitch mode.
Ensure that we always re-assign this value back to NULL after freeing
it, and move the ice_eswitch_release_reprs so that it can be called from
the setup function.
With these changes, eswitch cleanup no longer uses an unwind flow that
is problematic for the planned VF data structure change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit c685c69fba71 ("ixgbe: don't do any AF_XDP zero-copy transmit if
netif is not OK") addressed the ring transient state when
MEM_TYPE_XSK_BUFF_POOL was being configured which in turn caused the
interface to through down/up. Maurice reported that when carrier is not
ok and xsk_pool is present on ring pair, ksoftirqd will consume 100% CPU
cycles due to the constant NAPI rescheduling as ixgbe_poll() states that
there is still some work to be done.
To fix this, do not set work_done to false for a !netif_carrier_ok().
Fixes: c685c69fba71 ("ixgbe: don't do any AF_XDP zero-copy transmit if netif is not OK")
Reported-by: Maurice Baijens <maurice.baijens@ellips.com>
Tested-by: Maurice Baijens <maurice.baijens@ellips.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Print the offending plane/crtc id+name in the async flip debugs.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-5-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
The current implementation of the async flip wm0/ddb optimization
does not work at all. The biggest problem is that we skip the
whole intel_pipe_update_{start,end}() dance and thus never actually
complete the commit that is trying to do the wm/ddb change.
To fix this we need to move the do_async_flip flag to the crtc
state since we handle commits per-pipe, not per-plane.
Also since all planes can now be included in the first/last
"async flip" (which gets converted to a sync flip to do the
wm/ddb mangling) we need to be more careful when checking if
the plane state is async flip comptatible. Only planes doing
the async flip should be checked and other planes are perfectly
fine not adhereing to any async flip related limitations.
However for subsequent commits which are actually going do the
async flip in hardware we want to make sure no other planes
are in the state. That should never happen assuming we did our
job correctly, so we'll toss in a WARN to make sure we catch
any bugs here.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: c3639f3be480 ("drm/i915: Use wm0 only during async flips for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-4-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
Since the async flip state check is done very late and
thus it can see potentially all the planes in the state
(due to the wm/ddb optimization) we need to move the
"can the requested plane do async flips at all?" check
much earlier. For this purpose we introduce
intel_async_flip_check_uapi() that gets called early during
the atomic check.
And for good measure we'll throw in a couple of basic checks:
- is the crtc active?
- was a modeset flagged?
- is+was the plane enabled?
Though atm all of those should be guaranteed by the fact
that the async flip can only be requested through the legacy
page flip ioctl.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: c3639f3be480 ("drm/i915: Use wm0 only during async flips for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
data_rate==0 no longer means a plane is disabled, it could
also mean we want to use the minimum ddb allocation for it.
Hence we can't bail out early during ddb allocation or
else we'll simply forget to allocate any ddb for such planes.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Fixes: 6a4d8cc6bbbf ("drm/i915: Don't allocate extra ddb during async flip for DG2")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220214105532.13049-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
|
|
swrm_runtime_resume() would not be defined when CONFIG_PM=n
This causes below build failure
drivers/soundwire/qcom.c:1460:12: error: 'swrm_runtime_resume' defined
but not used [-Werror=unused-function]
Mark the resume swrm_runtime_resume() with __maybe_unused attribute.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220303110321.23666-1-srinivas.kandagatla@linaro.org
[redo commit title and log]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add support for Texas Instruments TMP464 and TMP468 temperature sensor
ICs.
TI's TMP464 is an I2C temperature sensor chip. This chip is similar
to TI's TMP421 chip, but with 16bit-wide registers (instead of
8bit-wide registers). The chip has one local sensor and four remote
sensors. TMP468 is similar to TMP464 but has one local and eight
remote sensors.
Originally-from: Agathe Porte <agathe.porte@nokia.com>
Cc: Agathe Porte <agathe.porte@nokia.com>
Cc: Krzysztof Adamski <krzysztof.adamski@nokia.com>
Tested-by: Agathe Porte <agathe.porte@nokia.com>
Link: https://lore.kernel.org/r/20220222223610.23098-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Fix an error message and report the correct failing function.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ret/retval will be set when it used, no need to init at definition.
[modified subject line -Mathias]
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is more readable to add blank lines.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to store temperary value in hcc_params.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It should be Device Context, not doorbell.
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The for loop to find page size bit can be replaced with ffs().
Signed-off-by: Linyu Yuan <quic_linyyuan@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A race between system resume and device-initiated resume may result in
runtime PM imbalance on USB2 root hub. If a device-initiated resume
starts and system resume xhci_bus_resume() directs U0 before hub driver
sees the resuming device in RESUME state, device-initiated resume will
not be finished in xhci_handle_usb2_port_link_resume(). In this case,
usb_hcd_end_port_resume() call is missing.
This changes calls usb_hcd_end_port_resume() if resuming device reaches
U0 to keep runtime PM balance.
Fixes: a231ec41e6f6 ("xhci: refactor U0 link state handling in get_port_status")
Cc: stable@vger.kernel.org
Signed-off-by: Henry Lin <henryl@nvidia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_decode_ctrl_ctx() returns the untouched buffer as-is if both "drop"
and "add" parameters are zero.
Fix the function to return an empty string in that case.
It was not immediately clear from the possible call chains whether this
issue is currently actually triggerable or not.
Note that before commit 4843b4b5ec64 ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 90d6d5731da7 ("xhci: Add tracing for input control context")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
commit 4843b4b5ec64 ("xhci: fix even more unsafe memory usage in xhci tracing")
Link: https://lore.kernel.org/r/20220303110903.1662404-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_decode_usbsts() is expected to return a zero-terminated string by
its only caller, xhci_stop_endpoint_command_watchdog(), which directly
logs the return value:
xhci_warn(xhci, "USBSTS:%s\n", xhci_decode_usbsts(str, usbsts));
However, if no recognized bits are set in usbsts, the function will
return without having called any sprintf() and therefore return an
untouched non-zero-terminated caller-provided buffer, causing garbage
to be output to log.
Fix that by always including the raw value in the output.
Note that before commit 4843b4b5ec64 ("xhci: fix even more unsafe memory
usage in xhci tracing") the result effect in the failure case was different
as a static buffer was used here, but the code still worked incorrectly.
Fixes: 9c1aa36efdae ("xhci: Show host status when watchdog triggers and host is assumed dead.")
Cc: stable@vger.kernel.org
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
xhci_reset() timeout was increased from 250ms to 10 seconds in order to
give Renesas 720201 xHC enough time to get ready in probe.
xhci_reset() is called with interrupts disabled in other places, and
waiting for 10 seconds there is not acceptable.
Add a timeout parameter to xhci_reset(), and adjust it back to 250ms
when called from xhci_stop() or xhci_shutdown() where interrupts are
disabled, and successful reset isn't that critical.
This solves issues when deactivating host mode on platforms like SM8450.
For now don't change the timeout if xHC is reset in xhci_resume().
No issues are reported for it, and we need the reset to succeed.
Locking around that reset needs to be revisited later.
Additionally change the signed integer timeout parameter in
xhci_handshake() to a u64 to match the timeout value we pass to
readl_poll_timeout_atomic()
Fixes: 22ceac191211 ("xhci: Increase reset timeout for Renesas 720201 host.")
Cc: stable@vger.kernel.org
Reported-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reported-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Tested-by: Pavan Kondeti <quic_pkondeti@quicinc.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220303110903.1662404-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to bring up the USB3 PHY on the Apple M1 we need to know the
orientation of the Type-C cable. Extract it from the status register and
forward it to the typec subsystem.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Link: https://lore.kernel.org/r/20220226125912.59828-1-sven@svenpeter.dev
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It does not make sense to have a comma after a sentinel, as any new
elements must be added before the sentinel.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5cae409f647272a5679291ebc0000bfeccc14160.1646311762.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
utc_tai_offset is used to correct IRIG, DCF and NMEA outputs and is
set during initialisation but is not corrected during leap second
announce event. Add watchdog code to control this correction.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TOD correction register is used to compensate for leap seconds in
different domains. Export it as an attribute with write access.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Monitoring of clock variance could be done through checking
the offset and the drift updates that are applied to atomic
clocks. Expose these values as attributes for the timecard.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TOD information is currently displayed only on module load,
which doesn't provide updated information as the system runs.
Create a debug file which provides the current TOD status information,
and move the information display there.
Signed-off-by: Vadim Fedorenko <vadfed@fb.com>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Right now, skb->tstamp is reset to 0 whenever the skb is forwarded.
If skb->tstamp has the mono delivery_time, clearing it can hurt
the performance when it finally transmits out to fq@phy-dev.
The earlier patch added a skb->mono_delivery_time bit to
flag the skb->tstamp carrying the mono delivery_time.
This patch adds skb_clear_tstamp() helper which keeps
the mono delivery_time and clears everything else.
The delivery_time clearing will be postponed until the stack knows the
skb will be delivered locally. It will be done in a latter patch.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Do mapping using CONTIGUOUS flag - otherwise
i915_gem_object_is_contiguous warn is triggered.
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211209141817.16038-1-stanislav.lisovskiy@intel.com
|
|
Support GREv0 without NAT.
Signed-off-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Acked-by: Paul Blakey <paulb@nvidia.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
In order for the Felix DSA driver to be able to turn on/off flooding
towards its CPU port, we need to redirect calls on the NPI port to
actually act upon the index in the analyzer block that corresponds to
the CPU port module. This was never necessary until now because DSA
(or the bridge) never called ocelot_port_bridge_flags() for the NPI
port.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
felix_migrate_flood_to_tag_8021q_port() takes care of clearing the
flooding bits on the old CPU port (which was the CPU port module), so
manually clearing this bit from PGID_UC, PGID_MC, PGID_BC is redundant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver probes with all ports as standalone, and it supports unicast
filtering. So DSA will call port_fdb_add() for all necessary addresses
on the current CPU port. We also handle migrations when the CPU port
hardware resource changes (on tagging protocol change), so there should
not be any unknown address that we have to receive while not promiscuous.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the tagging protocol changes from "ocelot" to "ocelot-8021q" or in
reverse, the DSA promiscuity setting that was applied for the old CPU
port must be transferred to the new one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "ocelot" and "ocelot-8021q" tagging protocols make use of different
hardware resources, and host FDB entries have different destination
ports in the switch analyzer module, practically speaking.
So when the user requests a tagging protocol change, the driver must
migrate all host FDB and MDB entries from the NPI port (in fact CPU port
module) towards the same physical port, but this time used as a regular
port.
It is pointless for the felix driver to keep a copy of the host
addresses, when we can create and export DSA helpers for walking through
the addresses that it already needs to keep on the CPU port, for
refcounting purposes.
felix_classify_db() is moved up to avoid a forward declaration.
We pass "bool change" because dp->fdbs and dp->mdbs are uninitialized
lists when felix_setup() first calls felix_set_tag_protocol(), so we
need to avoid calling dsa_port_walk_fdbs() during probe time.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
seqno could be read as a stale value outside of the lock. The lock is
already acquired to protect the modification of seqno against a possible
race condition. Place the reading of this value also inside this locking
to protect it against a possible race condition.
Signed-off-by: Niels Dossche <dossche.niels@gmail.com>
Acked-by: Martin Habets <habetsm.xilinx@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a new ice_gnss.c file for holding the basic GNSS module functions.
If the device supports GNSS module, call the new ice_gnss_init and
ice_gnss_release functions where appropriate.
Implement basic functionality for reading the data from GNSS module
using TTY device.
Add I2C read AQ command. It is now required for controlling the external
physical connectors via external I2C port expander on E810-T adapters.
Future changes will introduce write functionality.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Sudhansu Sekhar Mishra <sudhansu.mishra@intel.com>
Tested-by: Sunitha Mekala <sunithax.d.mekala@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 'kgdboc_earlycon_init' looks for boot console that has both .read
and .write callbacks. Adds 'samsung_early_read' to samsung_tty.c's early
console to support kgdboc.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Woody Lin <woodylin@google.com>
Link: https://lore.kernel.org/r/20220302114923.144523-1-woodylin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.
We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().
Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.
This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some users are suffering with PSR2 issues that are under debug or
issues that were root caused to panel firmware bugs, to make life of
those users easier here adding a option to disable PSR2 with kernel
parameters so they can still benefit from PSR1 power savings.
Using the same enable_psr that is current used to turn the whole
feature on or off and allowing user to select up to what PSR version
it should enable.
Right now users only set this parameter to 0 when they want to disable
PSR1 and PSR2 or don't add it at all leaving it to per-chip behavior
so it should not cause a bad impact on users.
v2:
- changing enable_psr values (Ville and Rodrigo)
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/4951
Cc: Jouni Högander <jouni.hogander@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220224202523.993560-1-jose.souza@intel.com
|
|
Currently we are observing occasional screen flickering when
PSR2 selective fetch is enabled. More specifically glitch seems
to happen on full frame update when cursor moves to coords
x = -1 or y = -1.
According to Bspec SF Single full frame should not be set if
SF Partial Frame Enable is not set. This happened to be true for
ADLP as PSR2_MAN_TRK_CTL_ENABLE is always set and for ADL_P it's
actually "SF Partial Frame Enable" (Bit 31).
Setting "SF Partial Frame Enable" bit also on full update seems to
fix screen flickering.
Also make code more clear by setting PSR2_MAN_TRK_CTL_ENABLE
only if not on ADL_P. Bit 31 has different meaning in ADL_P.
Bspec: 49274
v2: Fix Mihai Harpau email address
v3: Modify commit message and remove unnecessary comment
Tested-by: Lyude Paul <lyude@redhat.com>
Fixes: 7f6002e58025 ("drm/i915/display: Enable PSR2 selective fetch by default")
Reported-by: Lyude Paul <lyude@redhat.com>
Cc: Mihai Harpau <mharpau@gmail.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://gitlab.freedesktop.org/drm/intel/-/issues/5077
Signed-off-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220225070228.855138-1-jouni.hogander@intel.com
|
Dongdong Liu
Christoph Hellwig
Alex Williamson
Jacob Keller
Maciej Fijalkowski
Ville Syrjälä
Srinivas Kandagatla
Guenter Roeck
Christophe JAILLET
Linyu Yuan
Henry Lin
Anssi Hannula
Mathias Nyman
Sven Peter
Geert Uytterhoeven
Vadim Fedorenko
Martin KaFai Lau
Stanislav Lisovskiy
Toshiaki Makita
Vladimir Oltean
Niels Dossche
Karol Kolacinski
Woody Lin
Jiri Slaby
José Roberto de Souza
Jouni Högander