| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
These registers report CPU temperatures (and, depending on the system,
sometimes chipset temperatures) via the TSI interface on AMD systems.
They're distinct from most of the other Super-IO temperature readings
(CPUTIN, SYSTIN, etc.) in that they're not a selectable source for
monitoring and are in a different (higher resolution) format, but can
still provide useful temperature data.
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Tested-by: Renze Nicolai <renze@rnplus.nl>
Link: https://lore.kernel.org/r/20220113164629.21924-1-zev@bewilderbeest.net
Tested-by: Oleksandr Natalenko <oleksandr@natalenko.name>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Use with_info API to reduce code size and simplify the code.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
According to the March 2013 revision of the LM82 datasheet, the latest
LM82 die revision is 0x03. This was confirmed and observed with a real
chip. Further details in this revision of the LM82 datasheet suggest that
LM82 is now just a repackaged LM83. Such versions of LM82 will be detected
as LM83. Add comment to the code explaining why this may happen.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There should be no message in the kernel function if the detect function
fails to identify a chip; this is perfectly normal and does not warrant
a kernel log entry. Demote message to debug.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Replace TEMP_FROM_REG with direct calculation and TEMP_TO_REG
with standard functions/macros.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Using local caching in this driver had few benefits. It used cached values
for two seconds and then re-read all registers from the chip even if the
user only accessed a single attribute. On top of that, alarm attributes
were stale for up to four seconds (the first status register read reports
and clears an alarm, the second reports it cleared). Use regmap instead
for caching. Do not re-read non-volatile registers, and do not cache
volatile registers.
As part of this change, handle register read and write address differences
in regmap code. This is necessary to avoid problems with caching in the
regmap core, and ultimately simplifies the code.
Also, errors observed when reading from and writing to registers are no
longer ignored.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
It has no value to name a variable 'new_client' in probe and detect
functions; it is obvious that the client is new. Use 'client' as
variable name instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
There is no need to keep lm83_id at the end of the driver. Move it
forward to where it is needed to avoid a forward declaration.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Reorder include files to be in alphabetic order to simplify
driver maintenance.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Up to now udev events only report the affected hwmon device if an alert
is reported. This requires userspace to read all attributes if it wants
to know what triggered the event. Provide the attribute name with the
NAME property to help userspace find the attribute causing the event.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
On PMBUS devices with multiple pages, the regulator ops need to be
protected with the update mutex. This prevents accidentally changing
the page in a separate thread while operating on the PMBUS_OPERATION
register.
Tested on Infineon xdpe11280 while a separate thread polls for sensor
data.
Signed-off-by: Patrick Rudolph <patrick.rudolph@9elements.com>
Signed-off-by: Marcello Sylvester Bauer <sylv@sylv.io>
Link: https://lore.kernel.org/r/b991506bcbf665f7af185945f70bf9d5cf04637c.1645804976.git.sylv@sylv.io
Fixes: ddbb4db4ced1b ("hwmon: (pmbus) Add regulator support")
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Remove goto labels and use direct returns as error unwinding code only
needs to free t_page variable if we alloc_pages() call fails as having
two labels for one kfree() can be avoided easily.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220222152852.26043-3-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Only caller of null_alloc_page() is null_insert_page() unconditionally
sets only parameter to GFP_NOIO and that is statically hard-coded in
null_blk. There is no point in having statically hardcoded function
parameter.
Remove the unnecessary parameter gfp_flags and adjust the code, so it
can retain existing behavior null_alloc_page() with GFP_NOIO.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220222152852.26043-2-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Only caller of alloc_cmd() is null_submit_bio() unconditionally sets
second parameter to true and that is statically hard-coded in null_blk.
There is no point in having statically hardcoded function parameter.
Remove the unnecessary parameter can_wait and adjust the code so it
can retain existing behavior of waiting when we don't get valid
nullb_cmd from __alloc_cmd() in alloc_cmd().
The restructured code avoids multiple return statements, multiple
calls to __alloc_cmd() and resulting a fast path call to
prepare_to_wait() due to removal of first alloc_cmd() call.
Follow the pattern that we have in bio_alloc() to set the structure
members in the structure allocation function in alloc_cmd() and pass
bio to initialize newly allocated cmd->bio member.
Follow the pattern in copy_to_nullb() to use result of one function call
(null_cache_active()) to be used as a parameter to another function call
(null_insert_page()), use result of alloc_cmd() as a first parameter to
the null_handle_cmd() in null_submit_bio() function. This allow us to
remove the local variable cmd on stack in null_submit_bio() that is in
fast path.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Link: https://lore.kernel.org/r/20220216172945.31124-2-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Instead of hardcoding queue depth allow user to set the hw queue depth
using module parameter. Set default value to 128 to retain the existing
behavior.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20220215213310.7264-5-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The local variable file is used to pass it to the vfs_fsync(). We can
get away with using lo->lo_backing_file instead of storing in a local
variable which is not used anywhere else.
No functional change in this patch.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20220215213310.7264-4-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The local variable q is used to pass it to the blk_queue_discard(). We
can get away with using lo->lo_queue instead of storing in a local
variable which is not used anywhere else.
No functional change in this patch.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20220215213310.7264-3-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
sprintf does not know the PAGE_SIZE maximum of the temporary buffer
used for outputting sysfs content and it's possible to overrun the
PAGE_SIZE buffer length.
Use a generic sysfs_emit function that knows the size of the
temporary buffer and ensures that no overrun is done for offset
attribute in
loop_attr_[offset|sizelimit|autoclear|partscan|dio]_show() callbacks.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Link: https://lore.kernel.org/r/20220215213310.7264-2-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The function nullb_device_power_store() returns -ENOMEM when
null_add_dev() fails. null_add_dev() can fail with return value
other than -ENOMEM such as -EINVAL when Zoned Block Device option
is used, see :
nullb_device_power_store()
null_add_dev()
null_init_zoned_dev()
return -EINVAL;
When trying to load the module having -ENOMEM value returned on the
command line creates confusion when pleanty of memory is free on the
machine.
Instead of hardcoding -ENOMEM return the value of null_add_dev()
function.
Signed-off-by: Chaitanya Kulkarni <kch@nvidia.com>
Link: https://lore.kernel.org/r/20220215115951.15945-1-kch@nvidia.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The phrase "has still" should be "still has" to clean up the grammar.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220208114656.61629-1-colin.i.king@gmail.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
According to lib/idr.c,
The IDA handles its own locking. It is safe to call any of the IDA
functions without synchronisation in your code.
so the 'ida_lock' mutex can just be removed.
It is here only to protect some ida_simple_get()/ida_simple_remove() calls.
While at it, switch to ida_alloc_XXX()/ida_free() instead to
ida_simple_get()/ida_simple_remove().
The latter is deprecated and more verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Jack Wang <jinpu.wang@ionos.com>
Link: https://lore.kernel.org/r/7f9eccd8b1fce1bac45ac9b01a78cf72f54c0a61.1644266862.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
On client side, the device is a network device. There is no reason
to set rotational even-if the target device on server is rotational.
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Jack Wang <jinpu.wang@ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://lore.kernel.org/r/20220114155855.984144-3-haris.iqbal@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch fix the "CHECK:BRACES: braces {} should be used on all
arms of this statement" warning from checkpatch
Signed-off-by: Gioh Kim <gi-oh.kim@ionos.com>
Signed-off-by: Md Haris Iqbal <haris.iqbal@ionos.com>
Link: https://lore.kernel.org/r/20220114155855.984144-2-haris.iqbal@ionos.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Pull irq fix from Thomas Gleixner:
"A single fix for a regression caused by the recent PCI/MSI rework
which resulted in a recursive locking problem in the VMD driver.
The cure is to cache the relevant information upfront instead of
retrieving it at runtime"
* tag 'irq-urgent-2022-02-27' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
PCI: vmd: Prevent recursive locking on interrupt allocation
|
|
Pull pin control fixes from Linus Walleij:
- Fix some drive strength and pull-up code in the K210 driver.
- Add the Alder Lake-M ACPI ID so it starts to work properly.
- Use a static name for the StarFive GPIO irq_chip, forestalling an
upcoming fixes series from Marc Zyngier.
- Fix an ages old bug in the Tegra 186 driver where we were indexing at
random into struct and being lucky getting the right member.
* tag 'pinctrl-v5-17-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
gpio: tegra186: Fix chip_data type confusion
pinctrl: starfive: Use a static name for the GPIO irq_chip
pinctrl: tigerlake: Revert "Add Alder Lake-M ACPI ID"
pinctrl: k210: Fix bias-pull-up
pinctrl: fix loop in k210_pinconf_get_drive()
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields. Wrap the target region
in struct_group(). This additionally fixes a theoretical misalignment
of the copy (since the size of "buf" changes between 64-bit and 32-bit,
but this is likely never built for 64-bit).
FWIW, I think this code is totally broken on 64-bit (which appears to
not be a "real" build configuration): it would either always fail (with
an uninitialized data->buf_size) or would cause corruption in userspace
due to the copy_to_user() in the call path against an uninitialized
data->buf value:
omap3isp_stat_request_statistics_time32(...)
struct omap3isp_stat_data data64;
...
omap3isp_stat_request_statistics(stat, &data64);
int omap3isp_stat_request_statistics(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
buf = isp_stat_buf_get(stat, data);
static struct ispstat_buffer *isp_stat_buf_get(struct ispstat *stat,
struct omap3isp_stat_data *data)
...
if (buf->buf_size > data->buf_size) {
...
return ERR_PTR(-EINVAL);
}
...
rval = copy_to_user(data->buf,
buf->virt_addr,
buf->buf_size);
Regardless, additionally initialize data64 to be zero-filled to avoid
undefined behavior.
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: linux-media@vger.kernel.org
Fixes: 378e3f81cb56 ("media: omap3isp: support 64-bit version of omap3isp_stat_data")
Cc: stable@vger.kernel.org
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/lkml/20211215220505.GB21862@embeddedor
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
When building with -Warray-bounds under GCC 11.2, this warning was
emitted:
In function 'memset',
inlined from 'vtpm_proxy_fops_read' at drivers/char/tpm/tpm_vtpm_proxy.c:102:2:
./include/linux/fortify-string.h:43:33: warning: '__builtin_memset' pointer overflow between offset 164 and size [2147483648, 4294967295]
[-Warray-bounds]
43 | #define __underlying_memset __builtin_memset
| ^
This warning appears to be triggered due to the "count < len"
check in vtpm_proxy_fops_read() splitting the CFG[1], and the compiler
attempting to reason about the possible value range in len compared
to the buffer size.
In order to silence this warning, and to keep this code robust if the
use of proxy_dev->req_len ever changes in the future, explicitly check
the size of len before reaching the memset().
[1] https://lore.kernel.org/lkml/CAG48ez1iTF9KegKJrW5a3WzXgCPZJ73nS2_e5esKJRppdzvv8g@mail.gmail.com
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jarkko Sakkinen <jarkko@kernel.org>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: linux-integrity@vger.kernel.org
Reviewed-by: Stefan Berger <stefanb@linux.ibm.com>
Link: https://lore.kernel.org/lkml/4b59d305-6858-1514-751a-37853ad777be@linux.ibm.com
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20220119184354.3367603-1-keescook@chromium.org
|
|
Reduce the risk of integer overflow by doing the scale calculation on
a 64-bit integer. Since the rescaling is only performed on *val, reuse
the IIO_VAL_FRACTIONAL_LOG2 case.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-6-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The approximation caused by integer divisions can be costly on smaller
scale values since the decimal part is significant compared to the
integer part. Switch to an IIO_VAL_INT_PLUS_NANO scale type in such
cases to maintain accuracy.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-5-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is a preparatory change required for the addition of temperature
sensing front ends.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-4-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Some ADCs use IIO_VAL_INT_PLUS_{NANO,MICRO} scale types.
Add support for these to allow using the iio-rescaler with them.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-3-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In preparation for the addition of kunit tests, expose the logic
responsible for combining channel scales.
Signed-off-by: Liam Beguin <liambeguin@gmail.com>
Reviewed-by: Peter Rosin <peda@axentia.se>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20220213025739.2561834-2-liambeguin@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for K Band Downconverter with Integrated
Fractional-N PLL and VCO.
More info:
https://www.analog.com/en/products/admv4420.html
Signed-off-by: Cristian Pop <cristian.pop@analog.com>
Link: https://lore.kernel.org/r/20220223130808.13352-2-cristian.pop@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADA4250 is an instrumentation amplifier with SPI/pin-strap
progammable gains that is optimized for ultra-low power systems.
With a minimum supply voltage of 1.7V, 26uA of quiescent current,
a shutdown mode, a sleep mode, and a fast wake up settling time,
ADA4250 can be power cycled on a battery powered system for even
futher savings.
Signed-off-by: Antoniu Miclaus <antoniu.miclaus@analog.com>
Link: https://lore.kernel.org/r/20220223120112.8067-2-antoniu.miclaus@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Currently ocelot uses a pvid of 0 for standalone ports and ports under a
VLAN-unaware bridge, and the pvid of the bridge for ports under a
VLAN-aware bridge. Standalone ports do not perform learning, but packets
received on them are still subject to FDB lookups. So if the MAC DA that
a standalone port receives has been also learned on a VLAN-unaware
bridge port, ocelot will attempt to forward to that port, even though it
can't, so it will drop packets.
So there is a desire to avoid that, and isolate the FDBs of different
bridges from one another, and from standalone ports.
The ocelot switch library has two distinct entry points: the felix DSA
driver and the ocelot switchdev driver.
We need to code up a minimal bridge_num allocation in the ocelot
switchdev driver too, this is copied from DSA with the exception that
ocelot does not care about DSA trees, cross-chip bridging etc. So it
only looks at its own ports that are already in the same bridge.
The ocelot switchdev driver uses the bridge_num it has allocated itself,
while the felix driver uses the bridge_num allocated by DSA. They are
both stored inside ocelot_port->bridge_num by the common function
ocelot_port_bridge_join() which receives the bridge_num passed by value.
Once we have a bridge_num, we can only use it to enforce isolation
between VLAN-unaware bridges. As far as I can see, ocelot does not have
anything like a FID that further makes VLAN 100 from a port be different
to VLAN 100 from another port with regard to FDB lookup. So we simply
deny multiple VLAN-aware bridges.
For VLAN-unaware bridges, we crop the 4000-4095 VLAN region and we
allocate a VLAN for each bridge_num. This will be used as the pvid of
each port that is under that VLAN-unaware bridge, for as long as that
bridge is VLAN-unaware.
VID 0 remains only for standalone ports. It is okay if all standalone
ports use the same VID 0, since they perform no address learning, the
FDB will contain no entry in VLAN 0, so the packets will always be
flooded to the only possible destination, the CPU port.
The CPU port module doesn't need to be member of the VLANs to receive
packets, but if we use the DSA tag_8021q protocol, those packets are
part of the data plane as far as ocelot is concerned, so there it needs
to. Just ensure that the DSA tag_8021q CPU port is a member of all
reserved VLANs when it is created, and is removed when it is deleted.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For sja1105, to enforce FDB isolation simply means to turn on
Independent VLAN Learning unconditionally, and to remap VLAN-unaware FDB
and MDB entries towards the private VLAN allocated by tag_8021q for each
bridge.
Standalone ports each have their own standalone tag_8021q VLAN. No
learning happens in that VLAN due to:
- learning being disabled on standalone user ports
- learning being disabled on the CPU port (we use
assisted_learning_on_cpu_port which only installs bridge FDBs)
VLAN-aware ports learn FDB entries with the bridge VLANs.
VLAN-unaware bridge ports learn with the tag_8021q VLAN for bridging.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As FDB isolation cannot be enforced between VLAN-aware bridges in lack
of hardware assistance like extra FID bits, it seems plausible that many
DSA switches cannot do it. Therefore, they need to reject configurations
with multiple VLAN-aware bridges from the two code paths that can
transition towards that state:
- joining a VLAN-aware bridge
- toggling VLAN awareness on an existing bridge
The .port_vlan_filtering method already propagates the netlink extack to
the driver, let's propagate it from .port_bridge_join too, to make sure
that the driver can use the same function for both.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For DSA, to encourage drivers to perform FDB isolation simply means to
track which bridge does each FDB and MDB entry belong to. It then
becomes the driver responsibility to use something that makes the FDB
entry from one bridge not match the FDB lookup of ports from other
bridges.
The top-level functions where the bridge is determined are:
- dsa_port_fdb_{add,del}
- dsa_port_host_fdb_{add,del}
- dsa_port_mdb_{add,del}
- dsa_port_host_mdb_{add,del}
aka the pre-crosschip-notifier functions.
Changing the API to pass a reference to a bridge is not superfluous, and
looking at the passed bridge argument is not the same as having the
driver look at dsa_to_port(ds, port)->bridge from the ->port_fdb_add()
method.
DSA installs FDB and MDB entries on shared (CPU and DSA) ports as well,
and those do not have any dp->bridge information to retrieve, because
they are not in any bridge - they are merely the pipes that serve the
user ports that are in one or multiple bridges.
The struct dsa_bridge associated with each FDB/MDB entry is encapsulated
in a larger "struct dsa_db" database. Although only databases associated
to bridges are notified for now, this API will be the starting point for
implementing IFF_UNICAST_FLT in DSA. There, the idea is to install FDB
entries on the CPU port which belong to the corresponding user port's
port database. These are supposed to match only when the port is
standalone.
It is better to introduce the API in its expected final form than to
introduce it for bridges first, then to have to change drivers which may
have made one or more assumptions.
Drivers can use the provided bridge.num, but they can also use a
different numbering scheme that is more convenient.
DSA must perform refcounting on the CPU and DSA ports by also taking
into account the bridge number. So if two bridges request the same local
address, DSA must notify the driver twice, once for each bridge.
In fact, if the driver supports FDB isolation, DSA must perform
refcounting per bridge, but if the driver doesn't, DSA must refcount
host addresses across all bridges, otherwise it would be telling the
driver to delete an FDB entry for a bridge and the driver would delete
it for all bridges. So introduce a bool fdb_isolation in drivers which
would make all bridge databases passed to the cross-chip notifier have
the same number (0). This makes dsa_mac_addr_find() -> dsa_db_equal()
say that all bridge databases are the same database - which is
essentially the legacy behavior.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dsa_8021q_bridge_tx_fwd_offload_vid is no longer used just for
bridge TX forwarding offload, it is the private VLAN reserved for
VLAN-unaware bridging in a way that is compatible with FDB isolation.
So just rename it dsa_tag_8021q_bridge_vid.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the old Shared VLAN Learning mode of operation that tag_8021q
previously used for forwarding, we needed to have distinct concepts for
an RX and a TX VLAN.
An RX VLAN could be installed on all ports that were members of a given
bridge, so that autonomous forwarding could still work, while a TX VLAN
was dedicated for precise packet steering, so it just contained the CPU
port and one egress port.
Now that tag_8021q uses Independent VLAN Learning and imprecise RX/TX
all over, those lines have been blurred and we no longer have the need
to do precise TX towards a port that is in a bridge. As for standalone
ports, it is fine to use the same VLAN ID for both RX and TX.
This patch changes the tag_8021q format by shifting the VLAN range it
reserves, and halving it. Previously, our DIR bits were encoding the
VLAN direction (RX/TX) and were set to either 1 or 2. This meant that
tag_8021q reserved 2K VLANs, or 50% of the available range.
Change the DIR bits to a hardcoded value of 3 now, which makes tag_8021q
reserve only 1K VLANs, and a different range now (the last 1K). This is
done so that we leave the old format in place in case we need to return
to it.
In terms of code, the vid_is_dsa_8021q_rxvlan and vid_is_dsa_8021q_txvlan
functions go away. Any vid_is_dsa_8021q is both a TX and an RX VLAN, and
they are no longer distinct. For example, felix which did different
things for different VLAN types, now needs to handle the RX and the TX
logic for the same VLAN.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The felix driver, which also has a tagging protocol implementation based
on tag_8021q, does not care about adding the RX VLAN that is pvid on one
port on the other ports that are in the same bridge with it. It simply
doesn't need that, because in its implementation, the RX VLAN that is
pvid of a port is only used to install a TCAM rule that pushes that VLAN
ID towards the CPU port.
Now that tag_8021q no longer performs Shared VLAN Learning based
forwarding, the RX VLANs are actually segregated into two types:
standalone VLANs and VLAN-unaware bridging VLANs. Since you actually
have to call dsa_tag_8021q_bridge_join() to get a bridging VLAN from
tag_8021q, and felix does not do that because it doesn't need it, it
means that it only gets standalone port VLANs from tag_8021q. Which is
perfect because this means it can drop its workarounds that avoid the
VLANs it does not need.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For VLAN-unaware bridging, tag_8021q uses something perhaps a bit too
tied with the sja1105 switch: each port uses the same pvid which is also
used for standalone operation (a unique one from which the source port
and device ID can be retrieved when packets from that port are forwarded
to the CPU). Since each port has a unique pvid when performing
autonomous forwarding, the switch must be configured for Shared VLAN
Learning (SVL) such that the VLAN ID itself is ignored when performing
FDB lookups. Without SVL, packets would always be flooded, since FDB
lookup in the source port's VLAN would never find any entry.
First of all, to make tag_8021q more palatable to switches which might
not support Shared VLAN Learning, let's just use a common VLAN for all
ports that are under the same bridge.
Secondly, using Shared VLAN Learning means that FDB isolation can never
be enforced. But if all ports under the same VLAN-unaware bridge share
the same VLAN ID, it can.
The disadvantage is that the CPU port can no longer perform precise
source port identification for these packets. But at least we have a
mechanism which has proven to be adequate for that situation: imprecise
RX (dsa_find_designated_bridge_port_by_vid), which is what we use for
termination on VLAN-aware bridges.
The VLAN ID that VLAN-unaware bridges will use with tag_8021q is the
same one as we were previously using for imprecise TX (bridge TX
forwarding offload). It is already allocated, it is just a matter of
using it.
Note that because now all ports under the same bridge share the same
VLAN, the complexity of performing a tag_8021q bridge join decreases
dramatically. We no longer have to install the RX VLAN of a newly
joining port into the port membership of the existing bridge ports.
The newly joining port just becomes a member of the VLAN corresponding
to that bridge, and the other ports are already members of it from when
they joined the bridge themselves. So forwarding works properly.
This means that we can unhook dsa_tag_8021q_bridge_{join,leave} from the
cross-chip notifier level dsa_switch_bridge_{join,leave}. We can put
these calls directly into the sja1105 driver.
With this new mode of operation, a port controlled by tag_8021q can have
two pvids whereas before it could only have one. The pvid for standalone
operation is different from the pvid used for VLAN-unaware bridging.
This is done, again, so that FDB isolation can be enforced.
Let tag_8021q manage this by deleting the standalone pvid when a port
joins a bridge, and restoring it when it leaves it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hook up the new driver to configuration and build.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This provides the control pieces for kTLS Tx offload, implementinng the
offload operations.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the driver's data path. Tx handles skbs, XDP, and kTLS, Rx has skbs
and XDP. Also included are Rx and Tx queue creation/tear-down and
tracing.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The devlink part, which is minimal at this time giving just the driver
name.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ethtool operations, primarily related to queues and ports, as well
as device statistics.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is the first part of the Fungible ethernet driver. It deals with
device probing, net_device creation, and netdev ops.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fungible cards have a number of different PCI functions and thus
different drivers, all of which use a common method to initialize and
interact with the device. This commit adds a library module that
collects these common mechanisms. They mainly deal with device
initialization, setting up and destroying queues, and operating an admin
queue. A subset of the FW interface is also included here.
Signed-off-by: Dimitris Michailidis <dmichail@fungible.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update mlx5 command list and error return function to handle migration
commands.
Link: https://lore.kernel.org/all/20220224142024.147653-8-yishaih@nvidia.com
Signed-off-by: Yishai Hadas <yishaih@nvidia.com>
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
|
Zev Weiss
Guenter Roeck
Patrick Rudolph
Chaitanya Kulkarni
Colin Ian King
Christophe JAILLET
Gioh Kim
Linus Torvalds
Kees Cook
Liam Beguin
Cristian Pop
Antoniu Miclaus
Vladimir Oltean
Dimitris Michailidis
Yishai Hadas