| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Pull ata fixes from Damien Le Moal:
"Two fixes for the pata_hpt37x driver, both from Sergey:
- Fix a PCI register access using an incorrect size (8bits instead of
16bits)
- Make sure to always disable the primary channel as it is unused"
* tag 'ata-5.17-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/dlemoal/libata:
ata: pata_hpt37x: disable primary channel on HPT371
ata: pata_hpt37x: fix PCI clock detection
|
|
Recently userspace has started switching power_supply class devices with
a charge_type psy-property between fast and trickle charge mode, see:
https://gitlab.freedesktop.org/hadess/power-profiles-daemon/-/issues/85
Before this patch bq24190_charger_set_charge_type() would unconditionally
write charging or none to the BQ24190_REG_POC_CHG_CONFIG bits, replacing
the otg setting of those bits when the OTG 5V Vbus boost converter was on,
turning the 5V Vbus off, removing the power from any attached peripherals.
This fixes this by keeping track of otg_vbus_enabled and the requested
charger_type settings and when otg_vbus_enabled is true, delay applying
the charger_type until the 5V boost converter is turned off.
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
The datasheet says that the BQ24190_REG_POC_CHG_CONFIG bits can
have a value of either 10(0x2) or 11(0x3) for OTG (5V boost regulator)
mode.
Sofar bq24190_vbus_is_enabled() was only checking for 10 but some BIOS-es
uses 11 when enabling the regulator at boot.
Make bq24190_vbus_is_enabled() also check for 11 so that it does not
wrongly returns false when the bits are set to 11.
Fixes: 66b6bef2c4e0 ("power: supply: bq24190_charger: Export 5V boost converter as regulator")
Cc: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
When calculating pipe_mode and when doing readout we need
to order our steps correctly.
1. We start with adjusted_mode crtc timings being populated
with the transcoder timings (either via readout or
compute_config(). These will be per-segment for MSO.
2. For all other uses we want the full crtc timings so
we ask intel_splitter_adjust_timings() to expand
the per-segment numbers to their full glory
3. If bigjoiner is used we the divide the full numbers
down to per-pipe numbers using intel_bigjoiner_adjust_timings()
During readout we also have to reconstruct the adjusted_mode
normal timings (ie. not the crtc_ stuff). These are supposed
to reflect the full timings of the display. So we grab these
between steps 2 and 3.
The "user" mode readout (mainly done for fastboot purposes)
should be whatever mode the user would have used had they
asked us to do a modeset. We want the full timings for this
as the per-segment timings are not suppoesed to be user visible.
Also the user mode normal timings hdisplay/vdisplay need to
match PIPESRC (that is where we get our PIPESRC size
we doing a modeset with a user supplied mode).
And we end up with
- adjusted_mode normal timigns == full timings
- adjusted_mode crtc timings == transcoder timings
(per-segment timings for MSO, full timings otherwise)
- pipe_mode normal/crtc timings == pipe timings
(full timings divided by the number of bigjoiner pipes, if any)
- user mode normal timings == full timings with
hdisplay/vdisplay replaced with PIPESRC size
- user mode crtc timings == full timings
Yes, that is a lot of timings. One day we'll try to remove
some of the ones we don't actually need to keep around...
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-10-ville.syrjala@linux.intel.com
|
|
Pull intel_crtc_compute_pipe_mode() out from
intel_crtc_compute_config(). Since it's semi related
we'll suck in the max dotclock/double wide checks in
as well.
And we'll pimp the debugs while at it.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-9-ville.syrjala@linux.intel.com
|
|
intel_crtc_compute_config() doesn't really tell a unified story.
Let's chunk it up into pieces. We'll start with
intel_crtc_compute_pipe_src().
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-8-ville.syrjala@linux.intel.com
|
|
Deduplicate the code to convert the full timings to
per-pipe timings for bigjoiner usage.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-7-ville.syrjala@linux.intel.com
|
|
Let's not replicate the same piece of code to expand
the MSO segment timings to full width in many places.
Pull it into a helper
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-6-ville.syrjala@linux.intel.com
|
|
Do the s/dev_priv/i915/ and s/pipe_config/crtc_state/ renames
to intel_crtc_compute_config(). I want to start splitting this
up a bit and doing the renames now avoids spreading these old
nameing conventions elsewhere. No functional changes.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-5-ville.syrjala@linux.intel.com
|
|
We just copied over the whole master crtc state, including
cpu_transcoder+has_audio. No need to copy those again.
Also get rid of the unhelpful comment.
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-4-ville.syrjala@linux.intel.com
|
|
Adjust the cursor dst coordinates appripriately when it's on
the bigjoiner slave pipe. intel_atomic_plane_check_clipping()
already did this but with the cursor we discard those results
(apart from uapi.visible and error checks) since the hardware
will be doing the clipping for us.
v2: Rebase due to bigjoiner bitmask usage
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-3-ville.syrjala@linux.intel.com
|
|
bigjoiner_pipes==0 leads bigjoiner_master_pipe() to
do BIT(ffs(0)-1) which is undefined behaviour. The code should
actually still work fine since the only place we provoke
that is intel_crtc_bigjoiner_slave_pipes() and it'll bitwise
AND the result with 0, so doesn't really matter what we get
out of bigjoiner_master_pipe(). But best not provoke undefined
behaviour anyway.
Reported-by: kernel test robot <oliver.sang@intel.com>
Fixes: a6e7a006f5d5 ("drm/i915: Change bigjoiner state tracking to use the pipe bitmask")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220223131315.18016-2-ville.syrjala@linux.intel.com
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
|
|
Normally the native AXP288 fg/charger drivers are preferred but one some
devices the ACPI drivers should be used instead.
The ACPI battery/ac drivers use the acpi_quirk_skip_acpi_ac_and_battery()
helper to determine if they should skip loading because native fuel-gauge/
charger drivers like the AXP288 drivers will be used.
The new acpi_quirk_skip_acpi_ac_and_battery() helper includes a list of
exceptions for boards where the ACPI drivers should be used instead.
Use this new helper to avoid loading on such boards. Note this requires
adding a Kconfig dependency on ACPI, this is not a problem because ACPI
should be enabled on all boards with an AXP288 PMIC anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
Normally the native AXP288 fg/charger drivers are preferred but one some
devices the ACPI drivers should be used instead.
The ACPI battery/ac drivers use the acpi_quirk_skip_acpi_ac_and_battery()
helper to determine if they should skip loading because native fuel-gauge/
charger drivers like the AXP288 drivers will be used.
The new acpi_quirk_skip_acpi_ac_and_battery() helper includes a list of
exceptions for boards where the ACPI drivers should be used instead.
Use this new helper to avoid loading on such boards. Note this requires
adding a Kconfig dependency on ACPI, this is not a problem because ACPI
should be enabled on all boards with an AXP288 PMIC anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In order to do P2P communication the bridge ID of the platform must be in
the P2P device table.
Update the P2P device table with a device ID for the 3rd Gen Intel Xeon
Scalable Processors.
Link: https://lore.kernel.org/r/20220209162801.7647-1-michael.j.ruhl@intel.com
Signed-off-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
|
|
This JSP2 PCH actually seems to be some special Apple
specific ICP variant rather than a JSP. Make it so. Or at
least all the references to it seem to be some Apple ICL
machines. Didn't manage to find these PCI IDs in any
public chipset docs unfortunately.
The only thing we're losing here with this JSP->ICP change
is Wa_14011294188, but based on the HSD that isn't actually
needed on any ICP based design (including JSP), only TGP
based stuff (including MCC) really need it. The documented
w/a just never made that distinction because Windows didn't
want to differentiate between JSP and MCC (not sure how
they handle hpd/ddc/etc. then though...).
Cc: stable@vger.kernel.org
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Vivek Kasireddy <vivek.kasireddy@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4226
Fixes: 943682e3bd19 ("drm/i915: Introduce Jasper Lake PCH")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220224132142.12927-1-ville.syrjala@linux.intel.com
Acked-by: Vivek Kasireddy <vivek.kasireddy@intel.com>
Tested-by: Tomas Bzatek <bugs@bzatek.net>
|
|
The omap KMS driver will call drm_plane_create_color_properties() with
a default encoding and range values of BT601 and Full Range,
respectively.
Since the initial value wasn't carried over in the state, the driver had
to set it again in omap_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.
Reviewed-by: Tomi Valkeinen <tomba@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-23-maxime@cerno.tech
|
|
The drm_plane_create_color_properties() function asks for an initial
value for the color encoding and range, and will set the associated
plane state variable with that value if a state is present.
However, that function is usually called at a time where there's no
state yet. Since the drm_plane_state reset helper doesn't take care of
reading that value when it's called, it means that in most cases the
initial value will be 0 (so DRM_COLOR_YCBCR_BT601 and
DRM_COLOR_YCBCR_LIMITED_RANGE, respectively), or the drivers will have
to work around it.
Let's add some code in __drm_atomic_helper_plane_state_reset() to get
the initial encoding and range value if the property has been attached
in order to fix this.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-19-maxime@cerno.tech
|
|
The sun4i KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane type.
Since the initial value wasn't carried over in the state, the driver had
to set it again in sun4i_backend_layer_reset().
However, the helpers have been adjusted to set it properly at reset, so
this is not needed anymore.
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-sunxi@lists.linux.dev
Cc: Chen-Yu Tsai <wens@csie.org>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-18-maxime@cerno.tech
|
|
The sti KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane type.
Since the initial value wasn't carried over in the state, the driver had
to set it again in sti_plane_reset().
However, the helpers have been adjusted to set it properly at reset, so
this is not needed anymore.
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Philippe Cornu <philippe.cornu@foss.st.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-17-maxime@cerno.tech
|
|
The rcar-du KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane type.
Since the initial value wasn't carried over in the state, the driver had
to set it again in rcar_du_plane_reset() and rcar_du_vsp_plane_reset().
However, the helpers have been adjusted to set it properly at reset, so
this is not needed anymore.
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-16-maxime@cerno.tech
|
|
The omap KMS driver will call drm_plane_create_zpos_property() with an
init value of the plane index and the plane type.
Since the initial value wasn't carried over in the state, the driver had
to set it again in omap_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.
Reviewed-by: Tomi Valkeinen <tomba@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-15-maxime@cerno.tech
|
|
The nouveau KMS driver will call drm_plane_create_zpos_property() with
an init value depending on the plane purpose.
Since the initial value wasn't carried over in the state, the driver had
to set it again in nv50_wndw_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.
Cc: nouveau@lists.freedesktop.org
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Karol Herbst <kherbst@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Karol Herbst <kherbst@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-14-maxime@cerno.tech
|
|
The mdp KMS driver will call drm_plane_create_zpos_property() with an
init value depending on the plane purpose.
Since the initial value wasn't carried over in the state, the driver had
to set it again in mdp5_plane_reset(). However, the helpers have been
adjusted to set it properly at reset, so this is not needed anymore.
Cc: freedreno@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Cc: Rob Clark <robdclark@gmail.com>
Cc: Sean Paul <sean@poorly.run>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-13-maxime@cerno.tech
|
|
The drm_plane_create_zpos_property() function asks for an initial value,
and will set the associated plane state variable with that value if a
state is present.
However, that function is usually called at a time where there's no
state yet. Since the drm_plane_state reset helper doesn't take care of
reading that value when it's called, it means that in most cases the
initial value will be 0, or the drivers will have to work around it.
Let's add some code in __drm_atomic_helper_plane_state_reset() to get
the initial zpos value if the property has been attached in order to fix
this.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-8-maxime@cerno.tech
|
|
Some functions to create properties (drm_plane_create_zpos_property or
drm_plane_create_color_properties for example) will ask for a range of
acceptable value and an initial one.
This initial value is then stored in the values array for that property.
Let's provide an helper to access this property.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-7-maxime@cerno.tech
|
|
While the omap_plane_init() function calls
drm_plane_create_zpos_property() with an initial value of 0,
omap_plane_reset() will force it to another value depending on the plane
type.
Fix the discrepancy by setting the initial zpos value to the same value
in the drm_plane_create_zpos_property() call.
Reviewed-by: Tomi Valkeinen <tomba@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220221095918.18763-5-maxime@cerno.tech
|
|
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 causes the "option=value" string to be
added to init's environment strings, polluting it.
Fixes: 47dd7a540b8a ("net: add support for STMicroelectronics Ethernet controllers.")
Fixes: f3240e2811f0 ("stmmac: remove warning when compile as built-in (V2)")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Jose Abreu <joabreu@synopsys.com>
Link: https://lore.kernel.org/r/20220224033536.25056-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
__setup() handlers should return 1 on success, i.e., the parameter
has been handled. A return of 0 causes the "option=value" string to be
added to init's environment strings, polluting it.
Fixes: acc18c147b22 ("net: sxgbe: add EEE(Energy Efficient Ethernet) for Samsung sxgbe")
Fixes: 1edb9ca69e8a ("net: sxgbe: add basic framework for Samsung 10Gb ethernet driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Igor Zhbanov <i.zhbanov@omprussia.ru>
Link: lore.kernel.org/r/64644a2f-4a20-bab3-1e15-3b2cdd0defe3@omprussia.ru
Cc: Siva Reddy <siva.kallam@samsung.com>
Cc: Girish K S <ks.giri@samsung.com>
Cc: Byungho An <bh74.an@samsung.com>
Link: https://lore.kernel.org/r/20220224033528.24640-1-rdunlap@infradead.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
this patch adds gfxoff support for smu 13.0.5
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Based on smu 13.0.5 features, refine pp table code.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Register the CAN device only when all the necessary initialization is
completed. This patch makes sure all the data structures and locks are
initialized before registering the CAN device.
Link: https://lore.kernel.org/all/20220221225935.12300-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.
Some reasons why this API should be removed have been given by Julia
Lawall in [2].
A coccinelle script has been used to perform the needed transformation.
It can be found in [3].
[1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/
[3]: https://lore.kernel.org/kernel-janitors/20200716192821.321233-1-christophe.jaillet@wanadoo.fr/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In [1], Christoph Hellwig has proposed to remove the wrappers in
include/linux/pci-dma-compat.h.
Some reasons why this API should be removed have been given by Julia
Lawall in [2].
A coccinelle script has been used to perform the needed transformation.
It can be found in [3].
[1]: https://lore.kernel.org/kernel-janitors/20200421081257.GA131897@infradead.org/
[2]: https://lore.kernel.org/kernel-janitors/alpine.DEB.2.22.394.2007120902170.2424@hadrien/
[3]: https://lore.kernel.org/kernel-janitors/20200716192821.321233-1-christophe.jaillet@wanadoo.fr/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Samsung clock controller changes for v5.18
Add support for Tesla FSD SoC clock controller within Samsung Exynos SoC
clock controller drivers. The Tesla FSD's clock controller is similar
to Samsung Exynos one, so entire driver structure can be re-used.
* tag 'samsung-clk-fsd-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
clk: samsung: fix missing Tesla FSD dependency on Exynos
clk: samsung: fsd: Add cam_csi block clock information
clk: samsung: fsd: Add cmu_mfc block clock information
clk: samsung: fsd: Add cmu_imem block clock information
clk: samsung: fsd: Add cmu_fsys1 clock information
clk: samsung: fsd: Add cmu_fsys0 clock information
clk: samsung: fsd: Add cmu_peric block clock information
clk: samsung: fsd: Add initial clock support
dt-bindings: clock: Document FSD CMU bindings
dt-bindings: clock: Add bindings definitions for FSD CMU blocks
Link: https://lore.kernel.org/r/20220204154112.133723-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As we have deleted some flag, lets renumber them so there are no holes.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-33-michael@walle.cc
|
|
Now that there is almost no special case code left in
spi_nor_sr_ready(), the return check looks odd. Move the function call
closer to the return code checking.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-32-michael@walle.cc
|
|
Drop the generic spi_nor prefix for all the spansion functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-31-michael@walle.cc
|
|
Now that all functions using that flag are local to the spansion module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-30-michael@walle.cc
|
|
The clear status register flags is only available on spansion flashes.
Move all the functions around that into the spanion module.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-29-michael@walle.cc
|
|
Don't return early when the flash is smaller than or equal to 16MiB. We
need to be able to register hooks for all sizes of flashes. This also has
the benefit that it increases the readability of the code because the
action, i.e. registering the fixups, is connected to the condition, i.e.
flashes larger than 16MiB.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-28-michael@walle.cc
|
|
Drop the generic spi_nor prefix for all the micron-st functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-27-michael@walle.cc
|
|
Now that all functions using that flag are local to the micron module,
we can convert the flag to a manufacturer one.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-26-michael@walle.cc
|
|
The flag status register is only available on micron flashes. Move all
the functions around that into the micron module.
This is almost a mechanical move except for the spi_nor_fsr_ready()
which now also checks the normal status register. Previously, this was
done in spi_nor_ready().
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: Pratyush Yadav <p.yadav@ti.com> # on mt35xu512aba, s28hs512t
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-25-michael@walle.cc
|
|
XRDSR is a combination of xilinx and the RDSR opcode, but the register
is just the status register. Correct the debug message.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-24-michael@walle.cc
|
|
Drop the generic spi_nor prefix for all the xilinx functions.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-23-michael@walle.cc
|
|
Mechanically move all the xilinx functions to its own module.
Then register the new flash specific ready() function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-22-michael@walle.cc
|
|
The _page_size marco parameter was missing parentheses around it. Add
them.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-21-michael@walle.cc
|
|
We will move vendor specific code into the vendor modules and thus we
will have to export these functions so they can be called.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-20-michael@walle.cc
|
|
Xilinx and Micron flashes have their own implementation of the
spi_nor_ready() function. At the moment, the core will figure out
which one to call according to some flags. Lay the foundation to
make it possible that a flash can register its own ready()
function.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Link: https://lore.kernel.org/r/20220223134358.1914798-19-michael@walle.cc
|
Linus Torvalds
Hans de Goede
Ville Syrjälä
Michael J. Ruhl
Maxime Ripard
Dave Stevenson
Randy Dunlap
Yifan Zhang
Lad Prabhakar
Christophe JAILLET
Arnd Bergmann
Michael Walle