| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
After power up, the cs and clock is in default status, and the cs-high
and clock polarity dts property configuration will take no effect until
the calling of rockchip_spi_config in the first transmission.
So preset them to make sure a correct voltage before the first
transmission coming.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-5-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The spi which's version is higher than ver 2 will automatically
enable this feature.
If the length of master transmission is uncertain, the RK spi slave
is better to automatically stop after cs inactive instead of waiting
for xfer_completion forever.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-4-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This reverts commit 3710e80952cf2dc48257ac9f145b117b5f74e0a5.
Since idm_base and nicpm_base are still optional resources not present
on all platforms, this breaks the driver for everything except Northstar
2 (which has both).
The same change was already reverted once with 755f5738ff98 ("net:
broadcom: fix a mistake about ioremap resource").
So let's do it again.
Fixes: 3710e80952cf ("net: ethernet: bgmac: Use devm_platform_ioremap_resource_byname")
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
[florian: Added comments to explain the resources are optional]
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20220216184634.2032460-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At boot on the BCM2711, if the HDMI controllers are running, the CRTC
driver will disable itself and its associated HDMI controller to work
around a hardware bug that would leave some pixels stuck in a FIFO.
In order to avoid that issue, we need to run some operations in lockstep
between the CRTC and HDMI controller, and we need to make sure the HDMI
controller will be powered properly.
However, since we haven't enabled it through KMS, the runtime_pm state
is off at this point so we need to make sure the device is powered
through pm_runtime_resume_and_get, and once the operations are complete,
we call pm_runtime_put.
However, the HDMI controller will do that itself in its
post_crtc_powerdown, which means we'll end up calling pm_runtime_put for
a single pm_runtime_get, throwing the reference counting off. Let's
remove the pm_runtime_put call in the CRTC code in order to have the
proper counting.
Fixes: bca10db67bda ("drm/vc4: crtc: Make sure the HDMI controller is powered when disabling")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220203102003.1114673-1-maxime@cerno.tech
|
|
On bind we will register the HDMI codec device but we don't unregister
it on unbind, leading to a device leakage. Unregister our device at
unbind.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127111452.222002-1-maxime@cerno.tech
|
|
The qib driver load has been failing with the following message:
sysfs: cannot create duplicate filename '/devices/pci0000:80/0000:80:02.0/0000:81:00.0/infiniband/qib0/ports/1/linkcontrol'
The patch below has two "linkcontrol" names causing the duplication.
Fix by using the correct "diag_counters" name on the second instance.
Fixes: 4a7aaf88c89f ("RDMA/qib: Use attributes for the port sysfs")
Link: https://lore.kernel.org/r/1645106372-23004-1-git-send-email-mike.marciniszyn@cornelisnetworks.com
Cc: <stable@vger.kernel.org>
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@cornelisnetworks.com>
Signed-off-by: Mike Marciniszyn <mike.marciniszyn@cornelisnetworks.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
XRC INI QPs should be able to adjust their local ACK timeout.
Fixes: 2c1619edef61 ("IB/cma: Define option to set ack timeout and pack tos_set")
Link: https://lore.kernel.org/r/1644421175-31943-1-git-send-email-haakon.bugge@oracle.com
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Suggested-by: Avneesh Pant <avneesh.pant@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
After slave abort, all DMA should be stopped, or it will affect the
next transmission and maybe abort again.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-3-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Get num-cs u32 from dts of_node property rather than u16.
Signed-off-by: Jon Lin <jon.lin@rock-chips.com>
Link: https://lore.kernel.org/r/20220216014028.8123-2-jon.lin@rock-chips.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With the existing logic where clear_ack is true (HW doesn’t support
auto clear for ICR), interrupt clear register reset is not handled
properly. Due to this only the first interrupts get processed properly
and further interrupts are blocked due to not resetting interrupt
clear register.
Example for issue case where Invert_ack is false and clear_ack is true:
Say Default ISR=0x00 & ICR=0x00 and ISR is triggered with 2
interrupts making ISR = 0x11.
Step 1: Say ISR is set 0x11 (store status_buff = ISR). ISR needs to
be cleared with the help of ICR once the Interrupt is processed.
Step 2: Write ICR = 0x11 (status_buff), this will clear the ISR to 0x00.
Step 3: Issue - In the existing code, ICR is written with ICR =
~(status_buff) i.e ICR = 0xEE -> This will block all the interrupts
from raising except for interrupts 0 and 4. So expectation here is to
reset ICR, which will unblock all the interrupts.
if (chip->clear_ack) {
if (chip->ack_invert && !ret)
........
else if (!ret)
ret = regmap_write(map, reg,
~data->status_buf[i]);
So writing 0 and 0xff (when ack_invert is true) should have no effect, other
than clearing the ACKs just set.
Fixes: 3a6f0fb7b8eb ("regmap: irq: Add support to clear ack registers")
Signed-off-by: Prasad Kumpatla <quic_pkumpatl@quicinc.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Link: https://lore.kernel.org/r/20220217085007.30218-1-quic_pkumpatl@quicinc.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In order for the phy driver to be able to actually get and control
the cs and reset GPIOs the dev_id member of the gpiod_lookup table must
be set to point to the dev_name() of the ulpi-device instantiated by
dwc3_ulpi_init().
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-6-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Some Android x86 tablets with a Bay Trail (BYT) SoC and a Crystal Cove
PMIC, which does not support charger-detection, rely on the TUSB1211 phy
for charger-detection.
Windows tablets with the same SoC + PMIC often use an extra chip for
charger-detection like the FSA831A. But since on Android tablets
the designers already need to add a TUSB1211 phy to support device/gadget
mode the phy is used to do charger-detection instead.
These Android x86 tablets can be identified by the unique combination of
a Bay Trail SoC (already checked for by PCI-ids) + a Crystal Cove PMIC +
not using the standard ACPI battery and ac drivers. Where as on Windows
tablets the standard ACPI battery and ac drivers will be used on BYT
boards with a Crystal Cove PMIC.
Set a special kernel-internal (so not part of the dt-bindings)
"linux,phy_charger_detect" property on these boards, which tells the
tusb1210 driver to enable charger-detection.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-5-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The quirk handling may need to set some different properties
which means using a different swnode, move the setting of the swnode
to inside dwc3_pci_quirks() so that the quirk handling can choose
a different swnode.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-4-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
WUSB3801 features a configurable port type, accessory detection, and
plug orientation detection. It provides a hardware "ID" pin output for
compatibility with USB 2.0 OTG PHYs. Add a typec class driver for it.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220214050118.61015-5-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Basic programmable non-PD Type-C port controllers do not need the full
TCPM library, but they share the same devicetree binding and the same
typec_capability structure. Factor out a helper for parsing those
properties which map to fields in struct typec_capability, so the code
can be shared between TCPM and basic non-TCPM drivers.
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Link: https://lore.kernel.org/r/20220214050118.61015-4-samuel@sholland.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Simplify the code using max().
Generated by: scripts/coccinelle/misc/minmax.cocci
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: kernel test robot <lkp@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In xhci_endpoint_{disable|reset}() the expression '&vdev->eps[ep_index]'
just cannot be NULL, so the checks have no sense at all...
Found by Linux Verification Center (linuxtesting.org) with the SVACE static
analysis tool.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-9-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Trying to disable Link Powermanagement (LPM) before port reset is
unnecessary and can cause additional delay if host can't communicate
with the device, which is often the reason why device is reset in the
first place.
usb_disable_lpm() will
- zero usb U1/U2 timeouts for the hub downstream port
- send ENABLE U1/U2 clear feature requests to the connected device.
- increase internal reference count for udev->lpm_disable_count
There is no need to zero U1/U2 hub port timeouts, or clearing the
U1/U2 enable for the connected device before reset. These are set
to default by the reset.
USB 3.1 section 10.2.2 "HUB Downstream port U1/U2 timers" states that:
"the U1 and U2 timeout values for a downstream port reset to the default
values when the port receives a SetPortFeature request for a port reset"
Set the udev->lpm_disable_count to "1" after port reset, which is the
default lpm_disable_count value when allocating udev, representing
disabled LPM.
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Every lpm commmand, both for USB 2 and USB 3 devies used the same
xhci->lpm_command structure to change max exit latency.
xhci->lpm_command is only protected by a hcd->bandwidth mutex, which is
not enoungh as USB 2 and USB 3 devices are behind separate HCDs.
Simplify code and avoid unnecessary locking risks by allocating
separate command structures for each lpm command, just like with
all other commands.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To support systems with several xhci controllers with active
dbc on each xhci we need to use IDR to identify and give
an index to each port.
Avoid using global struct tty_driver.driver_state for storing
dbc port pointer as it won't work with several dbc ports
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The current workaround to call the dbc_tty_init() in probe is
not working in case we have several xhci devices with dbc enabled.
dbc_tty_init() should be called only once by a module init call when
module is loaded.
until dbgtty is its own module call dbc_tty_init() from xhci
module init call.
Same is true for unloading and dbc_tty_exit()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
These names give the impression the functions are related to
module init calls, but are in fact creating and removing the dbc
fake device
Rename them to xhci_create_dbc_dev() and xhci_remove_dbc_dev().
We will need the _init and _exit names for actual dbc module init
and exit calls.
No functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Turn the dbgtty closer to a device driver by allocating the dbc
structure in its own xhci_dbc_tty_probe() function, and freeing it
in xhci_dbc_tty_remove()
Remove xhci_do_dbc_exit() as its no longer needed.
allocate and create the dbc strcuture in xhci_dbc_tty_probe()
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Refactor xhci_dbc_init(), splitting it into logical
parts closer to the Linux device model.
- Create the fake dbc device, depends on xhci strucure
- Allocate a dbc structure, xhci agnostic
- Call xhci_dbc_tty_probe(), similar to actual probe.
Adjustments to xhci_dbc_exit and xhci_dbc_remove are also needed
as a result to the xhci_dbc_init() changes
Mostly non-functional changes, except for creating the dbc sysfs
entry earlier, together with the dbc structure.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20220216095153.1303105-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The CONFIG_OF maybe set, but it may not be applicable to a device. In
such case, checking against that can cause the device fail to
initialize. Check against the device node (device->of_node) instead.
Fixes: a102f07e4edf ("usb: dwc3: drd: Add support for usb-conn-gpio based usb-role-switch")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Thinh Nguyen <Thinh.Nguyen@synopsys.com>
Link: https://lore.kernel.org/r/9f15580ad5810b1e5f31c241b35ebedfbfc30a3f.1644964864.git.Thinh.Nguyen@synopsys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the custom functions xhci_mtk_ldos_{enable,disable}() by
switching to using regulator_bulk to perform the very same thing,
as the regulators are always either both enabled or both disabled.
Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://lore.kernel.org/r/20220214111905.77903-1-angelogioacchino.delregno@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the gadget driver hasn't been (yet) configured, and the cable is
connected to a HOST, the SFTDISCON gets cleared unconditionally, so the
HOST tries to enumerate it.
At the host side, this can result in a stuck USB port or worse. When
getting lucky, some dmesg can be observed at the host side:
new high-speed USB device number ...
device descriptor read/64, error -110
Fix it in drd, by checking the enabled flag before calling
dwc2_hsotg_core_connect(). It will be called later, once configured,
by the normal flow:
- udc_bind_to_driver
- usb_gadget_connect
- dwc2_hsotg_pullup
- dwc2_hsotg_core_connect
Fixes: 17f934024e84 ("usb: dwc2: override PHY input signals with usb role switch support")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@foss.st.com>
Link: https://lore.kernel.org/r/1644999135-13478-1-git-send-email-fabrice.gasnier@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the Bay Trail phy GPIO mappings where added cs and reset were swapped,
this did not cause any issues sofar, because sofar they were always driven
high/low at the same time.
Note the new mapping has been verified both in /sys/kernel/debug/gpio
output on Android factory images on multiple devices, as well as in
the schematics for some devices.
Fixes: 5741022cbdf3 ("usb: dwc3: pci: Add GPIO lookup table on platforms without ACPI GPIO resources")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20220213130524.18748-3-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The interrupt mask is enabled before any potential failure points in
the driver, which can leave a failure path where we exit with
interrupts enabled but the device not live. This causes an infinite
stream of interrupts on an Apple M1 Pro laptop on USB-C.
Add a failure label that's used post enabling interrupts, where we
mask them again before returning an error.
Suggested-by: Sven Peter <sven@svenpeter.dev>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Link: https://lore.kernel.org/r/e6b80669-20f3-06e7-9ed5-8951a9c6db6f@kernel.dk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Where it is possible (without out-of-patch-series-scope large scale
refactoring), correct code to remove checkpatch warnings about lines
that are too long, also correcting operator spacing where appropriate
for these lines as well. These warnings occur mostly due to so many
DBG_88E removals and parentheses tweaks etc. being adjacent to such
long lines, which are therefore included in the resultant diff.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-16-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove padapter parameter from aes_decipher function in
core/rtw_security.c, as I added it previously during debugging tweaks
and it is no longer required.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-15-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the rtw_sctx_chk_waring_status function from core/rtw_amit.c,
as it has only one caller which is unnecessary.
Suggested-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-14-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A number of style problems were left behind by the DBG_88E cleanup:
(1) Empty if/else blocks.
(2) Parenthesised if/while statements containing only one line.
(3) Entire blocks which server zero purpose after removal of DBG_88E.
(4) Various warnings about whitespace, and constant comparison order.
(5) Use of __constant_htons instead when htons should be used.
Fix up these issues across the driver in any file touched by the
previous cleanup. Long line warnings will be addresses in a later
patch.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-13-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove rtw_debug module parameter, and also the internal GlobalDebugLevel
flag and all places where it is referenced. As hal/odm_debug.c is now
essentially empty, also remove this file and edit the Makefile to no
longer reference it. The DBG_88E macro was the last user of these and
has now been removed, making the parameter and flag redundant.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-12-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove DBG_88E macro definition as it has no remaining callers within
the driver. This is part of the ongoing effort to cleanup the driver to
use standard debug mechanisms where appropriate.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-11-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all remaining calls to preprocessor aliases of DBG_88E, as well
as these definitions themselves. This is a prerequisite for removing
the DBG_88E macro itself.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-10-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the one remaining DBG_88E call from include/usb_ops.h. After
some thought, it makes more sense to just entirely strip all of these
calls, so that debugging code in the driver can be more consistent and
useful going forwards.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-9-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all remaining DBG_88E calls from the os_dep subdirectory. After
some thought, it makes more sense to just entirely strip all of these
calls, so that debugging code in the driver can be more consistent and
useful going forwards.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-8-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all remaining DBG_88E calls from os_dep/ioctl_linux.c, patching
separately from the rest of the os_dep subdirectory for ease of review
due to the sheer number of calls. After some thought, it makes more
sense to just entirely strip all of these calls, so that debugging
code in the driver can be more consistent and useful going forwards.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-7-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all remaining DBG_88E calls from the hal subdirectory. After some
thought, it makes more sense to just entirely strip all of these calls,
so that debugging code in the driver can be more consistent and useful
going forwards.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-6-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all remaining DBG_88E calls from the core subdirectory. After some
thought, it makes more sense to just entirely strip all of these calls,
so that debugging code in the driver can be more consistent and useful
going forwards.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-5-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all the netdev_dbg/pr_debug calls that were previously converted
from DBG_88E inside core/rtw_mlme_ext.c. Due to the sheer number of
lines, this patch is separated out for ease of review. After some thought,
it makes more sense to just entirely strip all of these calls, so that
debugging code in the driver can be more consistent and useful going
forwards.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-4-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all the smaller sets of dev_dbg/netdev_dbg/pr_debug calls that
were previously converted from DBG_88E. After some thought, it makes
more sense to just entirely strip all of these calls, so that debugging
code in the driver can be more consistent and useful going forwards.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-3-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove all netdev_dbg and dev_dbg calls that were previously converted
from DBG_88E_LEVEL. After some thought, it makes more sense to just
entirely strip all of these calls, so that debugging code in the driver
can be more consistent and useful going forwards.
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20220216010709.791-2-phil@philpotter.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
struct usb_suspend_parm is not used. Remove it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20220216081657.622467-4-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
evt_done_cnt in struct evt_priv is set but not used. Remove it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20220216081657.622467-3-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
evt_allocated_buf in struct evt_priv is not used. Remove it.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20220216081657.622467-2-martin@kaiser.cx
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is a spelling mistake in a dev_warn message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Link: https://lore.kernel.org/r/20220217104747.15424-1-colin.i.king@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, the DT bindings the wfx driver cannot be processed by make
dt_binding_check. We need to place it somewhere into
Documentation/devicetree/bindings/.
After that change, we are able to get warnings from dt_binding_check and
fix them.
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20220217103248.183770-1-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Until now, the SDIO quirks are applied directly from the driver.
However, it is better to apply the quirks before driver probing. So,
this patch relocate the quirks in the MMC framework.
Note that the WF200 has no valid SDIO VID/PID. Therefore, we match DT
rather than on the SDIO VID/PID.
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Jérôme Pouiller <jerome.pouiller@silabs.com>
Link: https://lore.kernel.org/r/20220216093112.92469-3-Jerome.Pouiller@silabs.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
Jon Lin
Jonas Gorski
Maxime Ripard
Mike Marciniszyn
Håkon Bugge
Prasad Kumpatla
Hans de Goede
Samuel Holland
kernel test robot
Sergey Shtylyov
Mathias Nyman
Thinh Nguyen
AngeloGioacchino Del Regno
Fabrice Gasnier
Jens Axboe
Phillip Potter
Martin Kaiser
Colin Ian King
Jérôme Pouiller