| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
On the BCM2711, the HDMI_VEC_INTERFACE_XBAR register configuration
depends on whether we're using an RGB or YUV output. Let's move that
configuration to the CSC setup.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-8-maxime@cerno.tech
|
|
The CSC callbacks takes a boolean as an argument to tell whether we're
using the full range or limited range RGB.
However, with the upcoming YUV support, the logic will be a bit more
complex. In order to address this, let's make the callbacks take the
entire mode, and call our new helper to tell whether the full or limited
range RGB should be used.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-7-maxime@cerno.tech
|
|
We're going to need to tell whether we want to run with a full or
limited range RGB output in multiple places in the code, so let's create
a helper that will return whether we need with full range or not.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-6-maxime@cerno.tech
|
|
The HDMI specification mentions YCbCr everywhere, but our enums have
YCrCb. Let's rename it to match.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-5-maxime@cerno.tech
|
|
The current code assumes that the RGB444 and YUV444 formats are the
same, but the HDMI 2.0 specification states that:
The three DC_XXbit bits above only indicate support for RGB 4:4:4 at
that pixel size. Support for YCBCR 4:4:4 in Deep Color modes is
indicated with the DC_Y444 bit. If DC_Y444 is set, then YCBCR 4:4:4
is supported for all modes indicated by the DC_XXbit flags.
So if we have YUV444 support and any DC_XXbit flag set but the DC_Y444
flag isn't, we'll assume that we support that deep colour mode for
YUV444 which breaks the specification.
In order to fix this, let's split the edid_hdmi_dc_modes field in struct
drm_display_info into two fields, one for RGB444 and one for YUV444.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d0c94692e0a3 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-4-maxime@cerno.tech
|
|
The current code, when parsing the EDID Deep Color depths, that the
YUV422 cannot be used, referring to the HDMI 1.3 Specification.
This specification, in its section 6.2.4, indeed states:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is not permitted for any Deep Color mode.
This indeed can be interpreted like the code does, but the HDMI 1.4
specification further clarifies that statement in its section 6.2.4:
For each supported Deep Color mode, RGB 4:4:4 shall be supported and
optionally YCBCR 4:4:4 may be supported.
YCBCR 4:2:2 is also 36-bit mode but does not require the further use
of the Deep Color modes described in section 6.5.2 and 6.5.3.
This means that, even though YUV422 can be used with 12 bit per color,
it shouldn't be treated as a deep color mode.
This is also broken with YUV444 if it's supported by the display, but
DRM_EDID_HDMI_DC_Y444 isn't set. In such a case, the code will clear
color_formats of the YUV444 support set previously in
drm_parse_cea_ext(), but will not set it back.
Since the formats supported are already setup properly in
drm_parse_cea_ext(), let's just remove the code modifying the formats in
drm_parse_hdmi_deep_color_info()
Fixes: d0c94692e0a3 ("drm/edid: Parse and handle HDMI deep color modes.")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-3-maxime@cerno.tech
|
|
The drm_hdmi_avi_infoframe_colorspace() function actually sets the
colorimetry and extended_colorimetry fields in the hdmi_avi_infoframe
structure with DRM_MODE_COLORIMETRY_* values.
To make things worse, the hdmi_avi_infoframe structure also has a
colorspace field used to signal whether an RGB or YUV output is being
used.
Let's remove the inconsistency and allow for the colorspace usage by
renaming the function.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120151625.594595-2-maxime@cerno.tech
|
|
Also add notes that for atomic drivers it's really somewhere else and
no longer in struct drm_crtc.
Maybe we should put a bigger warning here that this is confusing,
since the pixel format is a plane property, but the GAMMA_LUT property
is on the crtc. But I think we can fix this if/when someone finds a
need for a per-plane CLUT, since I'm not sure such hw even exists. I'm
also not sure whether even hardware with a CLUT and a full color
correction pipeline with degamm/cgm/gamma exists.
Motivated by comments from Geert that we have a gap here.
v2: More names for color luts (Laurent).
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124221633.952374-1-daniel.vetter@ffwll.ch
|
|
In case of a modeset where a mode gets split across multiple CRTCs
in the driver specific implementation (bigjoiner in i915) we wrongly count
the affected CRTCs based on the drm_crtc_mask and indicate the stolen CRTC as
an affected CRTC in atomic_check_only().
This triggers a warning since affected CRTCs doent match requested CRTC.
To fix this in such bigjoiner configurations, we should only
increment affected crtcs if that CRTC is enabled in UAPI not
if it is just used internally in the driver to split the mode.
v3: Add the same uapi crtc_state->enable check in requested
crtc calc (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Simon Ser <contact@emersion.fr>
Cc: Pekka Paalanen <pekka.paalanen@collabora.co.uk>
Cc: Daniel Stone <daniels@collabora.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: <stable@vger.kernel.org> # v5.11+
Fixes: 919c2299a893 ("drm/i915: Enable bigjoiner")
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211004115913.23889-1-manasi.d.navare@intel.com
|
|
Log subpages are starting to appear in real devices (e.g. SSDs) so add
support for one. Adopt approach where all "wild" sub-pages are themselves
listed as long as there is at least one non-wild page or subpage for a
given page number.
Link: https://lore.kernel.org/r/20220109012853.301953-10-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
By default, this driver places a read lock around all user data fetches and
a write lock around all user data modifying operations (e.g. WRITE
commands). These locks have "per store" granularity. Other drivers that
have a similar function (e.g. null_blk) do not take this data integrity
step and run significantly faster in some tests.
In the common case of a (simulated) device to device copy (e.g. what dd
and its variants do) there should be no need for locks around data
accesses. So add the driver and sysfs parameter no_rwlock which is boolean
and when set does what its name suggests. The default is false for backward
comaptibility.
Link: https://lore.kernel.org/r/20220109012853.301953-7-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
To distinguish between resets sent by the SCSI mid-level error
handling and newly introduced devices (LUs), this Unit Attention:
power on, reset, or bus reset occurred [0x29,0x0]
has been subdivided into that UA for the reset case and this new UA:
power on occurred [0x29,0x1]
for the new device (LU) case. This makes debug a little easier to follow
when it is turned on (e.g. 'echo 0x1 > opts').
Bump driver version number.
Link: https://lore.kernel.org/r/20220109012853.301953-6-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Refine the sdebug_blk_mq_poll() function so it only takes the spinlock on
the queue when it can see one or more requests with the in_use bitmap flag
set.
Link: https://lore.kernel.org/r/20220109012853.301953-5-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When the internal in_use bit array in this driver is full returning
SCSI_MLQUEUE_HOST_BUSY leads to the mid-level reissuing the request which
is unhelpful. Previously TASK SET FULL status was only returned if ALL_TSF
[0x400] is placed in the opts variable (at load time or via sysfs). Now
ignore that setting and always return TASK SET FULL when in_use array is
full. Also set DID_ABORT together with TASK SET FULL so the mid-level gives
up immediately.
Aside: the situations addressed by this patch lead to lockups and
timeouts. They have only been detected when blk_poll() is used. That
mechanism is relatively new in the SCSI subsystem suggesting the mid-level
may need more work in that area.
Link: https://lore.kernel.org/r/20220109012853.301953-4-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use READ_ONCE() and WRITE_ONCE() macros when accessing the
sdebug_defer::defer_t value.
Link: https://lore.kernel.org/r/20220109012853.301953-3-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When scsi_debug is loaded as a module with many (simulated) hosts, targets,
and devices (LUs), modprobe can take a long time to return. Only a small
amount of this time is spent in the scsi_debug_init(); the rest is other
parts of the kernel reacting to to the appearance of new storage
devices. As soon as scsi_debug_init() has completed the user space may call
'rmmod scsi_debug' and this was found to cause race problems as outlined
here:
https://bugzilla.kernel.org/show_bug.cgi?id=212337
To reliably generate this race a sysfs parameter called rm_all_hosts was
added and the code was strengthened in this area. The main change was to
make the count of scsi_debug hosts present an atomic. Then it was found
that the handling of the existing add_host parameter needed the same
strengthening. Further: 'echo -9999 >
/sys/bus/pseudo/drivers/scsi_debug/add_host has the same effect as
rm_all_hosts so rm_all_hosts was not needed.
To inhibit a race between two invocations of writes to add_host, a mutex
was added. Also address a possible race when rmmod is called but LUs are
still being added.
The logic to remove (all) hosts is rather crude: it works backwards down a
linked lists of hosts. Any pending requests are terminated with
DID_NO_CONNECT as are any new requests. In the case where not all hosts are
being removed, the ones that remain may have lost requests as just
outlined. The lowest numbered host (id) hosts will remain.
Cc: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20220109012853.301953-2-dgilbert@interlog.com
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Smatch detected a divide by zero bug in check_overlay_scaling().
drivers/gpu/drm/i915/display/intel_overlay.c:976 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_height'.
drivers/gpu/drm/i915/display/intel_overlay.c:980 check_overlay_scaling()
error: potential divide by zero bug '/ rec->dst_width'.
Prevent this by ensuring that the dst height and width are non-zero.
Fixes: 02e792fbaadb ("drm/i915: implement drmmode overlay support v4")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220124122409.GA31673@kili
|
|
In myrs_detect(), cs->disable_intr is NULL when privdata->hw_init() fails
with non-zero. In this case, myrs_cleanup(cs) will call a NULL ptr and
crash the kernel.
[ 1.105606] myrs 0000:00:03.0: Unknown Initialization Error 5A
[ 1.105872] myrs 0000:00:03.0: Failed to initialize Controller
[ 1.106082] BUG: kernel NULL pointer dereference, address: 0000000000000000
[ 1.110774] Call Trace:
[ 1.110950] myrs_cleanup+0xe4/0x150 [myrs]
[ 1.111135] myrs_probe.cold+0x91/0x56a [myrs]
[ 1.111302] ? DAC960_GEM_intr_handler+0x1f0/0x1f0 [myrs]
[ 1.111500] local_pci_probe+0x48/0x90
Link: https://lore.kernel.org/r/20220123225717.1069538-1-ztong0001@gmail.com
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Pointer SCp is being re-assigned the same value that it was initialized to
a few lines earlier, the assignment is redundant and can be removed.
Link: https://lore.kernel.org/r/20220123175530.110462-1-colin.i.king@gmail.com
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This event is raised when link is lost as specified in UFSHCI spec and that
means communication is not possible. Thus initializing UFS interface needs
to be done.
Make UFS driver considers Link Lost as fatal in the INT_FATAL_ERRORS
mask. This will trigger a host reset whenever a link lost interrupt occurs.
Link: https://lore.kernel.org/r/1642743475-54275-1-git-send-email-kwmad.kim@samsung.com
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The return value of ufshcd_set_dev_pwr_mode() is passed to device PM
core. However, the function currently returns a SCSI result which the PM
core doesn't understand. This might lead to unexpected behaviors in
userland; a platform reset was observed in Android.
Use a generic error code for SSU failures.
Link: https://lore.kernel.org/r/1642743182-54098-1-git-send-email-kwmad.kim@samsung.com
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Kiwoong Kim <kwmad.kim@samsung.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Link: https://lore.kernel.org/r/20220110050218.3958-18-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
While allocating firmware dump, check if dump is already collected and do
not re-allocate the buffer.
Link: https://lore.kernel.org/r/20220110050218.3958-17-njavali@marvell.com
Cc: stable@vger.kernel.org
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This is an update to the original 28xx adapter enablement. Add a bunch of
conditionals that are applicable for 28xx.
Link: https://lore.kernel.org/r/20220110050218.3958-16-njavali@marvell.com
Fixes: ecc89f25e225 ("scsi: qla2xxx: Add Device ID for ISP28XX")
Cc: stable@vger.kernel.org
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
[ 12.323788] BUG: using smp_processor_id() in preemptible [00000000] code: systemd-udevd/1020
[ 12.332297] caller is qla2xxx_create_qpair+0x32a/0x5d0 [qla2xxx]
[ 12.338417] CPU: 7 PID: 1020 Comm: systemd-udevd Tainted: G I --------- --- 5.14.0-29.el9.x86_64 #1
[ 12.348827] Hardware name: Dell Inc. PowerEdge R610/0F0XJ6, BIOS 6.6.0 05/22/2018
[ 12.356356] Call Trace:
[ 12.358821] dump_stack_lvl+0x34/0x44
[ 12.362514] check_preemption_disabled+0xd9/0xe0
[ 12.367164] qla2xxx_create_qpair+0x32a/0x5d0 [qla2xxx]
[ 12.372481] qla2x00_probe_one+0xa3a/0x1b80 [qla2xxx]
[ 12.377617] ? _raw_spin_lock_irqsave+0x19/0x40
[ 12.384284] local_pci_probe+0x42/0x80
[ 12.390162] ? pci_match_device+0xd7/0x110
[ 12.396366] pci_device_probe+0xfd/0x1b0
[ 12.402372] really_probe+0x1e7/0x3e0
[ 12.408114] __driver_probe_device+0xfe/0x180
[ 12.414544] driver_probe_device+0x1e/0x90
[ 12.420685] __driver_attach+0xc0/0x1c0
[ 12.426536] ? __device_attach_driver+0xe0/0xe0
[ 12.433061] ? __device_attach_driver+0xe0/0xe0
[ 12.439538] bus_for_each_dev+0x78/0xc0
[ 12.445294] bus_add_driver+0x12b/0x1e0
[ 12.451021] driver_register+0x8f/0xe0
[ 12.456631] ? 0xffffffffc07bc000
[ 12.461773] qla2x00_module_init+0x1be/0x229 [qla2xxx]
[ 12.468776] do_one_initcall+0x44/0x200
[ 12.474401] ? load_module+0xad3/0xba0
[ 12.479908] ? kmem_cache_alloc_trace+0x45/0x410
[ 12.486268] do_init_module+0x5c/0x280
[ 12.491730] __do_sys_init_module+0x12e/0x1b0
[ 12.497785] do_syscall_64+0x3b/0x90
[ 12.503029] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 12.509764] RIP: 0033:0x7f554f73ab2e
Link: https://lore.kernel.org/r/20220110050218.3958-15-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
28XX adapters are capable of detecting both T10 PI tag escape values as
well as IP guard. This was missed due to the adapter type missed in the
corresponding macros. Fix this by adding support for 28xx in those macros.
Link: https://lore.kernel.org/r/20220110050218.3958-14-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Tested-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Joe Carnuccio <joe.carnuccio@cavium.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Silence compile warning due to unaligned memory access.
qla_edif.c:713:45: warning: taking address of packed member 'u' of class or
structure 'auth_complete_cmd' may result in an unaligned pointer value
[-Waddress-of-packed-member]
fcport = qla2x00_find_fcport_by_pid(vha, &appplogiok.u.d_id);
Link: https://lore.kernel.org/r/20220110050218.3958-13-njavali@marvell.com
Cc: stable@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix smatch-reported warning message:
drivers/scsi/qla2xxx/qla_target.c:3324 qlt_xmit_response() warn: missing error
code 'res'
Link: https://lore.kernel.org/r/20220110050218.3958-12-njavali@marvell.com
Fixes: 4a8f71014b4d ("scsi: qla2xxx: Fix unmap of already freed sgl")
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
A device logout in loop topology initiates a device connection teardown
which loses the FW device handle. In loop topo, the device handle is not
regrabbed leading to device login failures and eventually to loss of the
device. Fix this by taking the main login path that does it.
Link: https://lore.kernel.org/r/20220110050218.3958-11-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Arun Easi <aeasi@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Add ql2xnvme_queues module parameter to configure number of NVMe queues
Usage:
Number of NVMe Queues that can be configured.
Final value will be min(ql2xnvme_queues, num_cpus, num_chip_queues),
1 - Minimum number of queues supported
8 - Default value
128 - Maximum number of queues supported
Link: https://lore.kernel.org/r/20220110050218.3958-10-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Shreyas Deodhar <sdeodhar@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Corrected transmission speed mask values for FC.
Supported Speed: 16 32 20 Gb/s ===> Should be 64 instead of 20
Supported Speed: 16G 32G 48G ===> Should be 64G instead of 48G
Link: https://lore.kernel.org/r/20220110050218.3958-9-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Bikash Hazarika <bhazarika@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Per FW request, Exec FW can fail due to temporary error resulting in driver
not attaching to the adapter. Add retry of this command up to 4 retries.
Link: https://lore.kernel.org/r/20220110050218.3958-8-njavali@marvell.com
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver makes a call into midlayer (fc_remote_port_delete) which can put
the thread to sleep. The thread that originates the call is in interrupt
context. The combination of the two trigger a crash. Schedule the call in
non-interrupt context where it is more safe.
kernel: BUG: scheduling while atomic: swapper/7/0/0x00010000
kernel: Call Trace:
kernel: <IRQ>
kernel: dump_stack+0x66/0x81
kernel: __schedule_bug.cold.90+0x5/0x1d
kernel: __schedule+0x7af/0x960
kernel: schedule+0x28/0x80
kernel: schedule_timeout+0x26d/0x3b0
kernel: wait_for_completion+0xb4/0x140
kernel: ? wake_up_q+0x70/0x70
kernel: __wait_rcu_gp+0x12c/0x160
kernel: ? sdev_evt_alloc+0xc0/0x180 [scsi_mod]
kernel: synchronize_sched+0x6c/0x80
kernel: ? call_rcu_bh+0x20/0x20
kernel: ? __bpf_trace_rcu_invoke_callback+0x10/0x10
kernel: sdev_evt_alloc+0xfd/0x180 [scsi_mod]
kernel: starget_for_each_device+0x85/0xb0 [scsi_mod]
kernel: ? scsi_init_io+0x360/0x3d0 [scsi_mod]
kernel: scsi_init_io+0x388/0x3d0 [scsi_mod]
kernel: device_for_each_child+0x54/0x90
kernel: fc_remote_port_delete+0x70/0xe0 [scsi_transport_fc]
kernel: qla2x00_schedule_rport_del+0x62/0xf0 [qla2xxx]
kernel: qla2x00_mark_device_lost+0x9c/0xd0 [qla2xxx]
kernel: qla24xx_handle_plogi_done_event+0x55f/0x570 [qla2xxx]
kernel: qla2x00_async_login_sp_done+0xd2/0x100 [qla2xxx]
kernel: qla24xx_logio_entry+0x13a/0x3c0 [qla2xxx]
kernel: qla24xx_process_response_queue+0x306/0x400 [qla2xxx]
kernel: qla24xx_msix_rsp_q+0x3f/0xb0 [qla2xxx]
kernel: __handle_irq_event_percpu+0x40/0x180
kernel: handle_irq_event_percpu+0x30/0x80
kernel: handle_irq_event+0x36/0x60
Link: https://lore.kernel.org/r/20220110050218.3958-7-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
After a recoverable PCI error has been detected and recovered, qla driver
needs to check to see if the error condition still persist and/or wait
for the OS to give the resume signal.
Sep 8 22:26:03 localhost kernel: WARNING: CPU: 9 PID: 124606 at qla_tmpl.c:440
qla27xx_fwdt_entry_t266+0x55/0x60 [qla2xxx]
Sep 8 22:26:03 localhost kernel: RIP: 0010:qla27xx_fwdt_entry_t266+0x55/0x60
[qla2xxx]
Sep 8 22:26:03 localhost kernel: Call Trace:
Sep 8 22:26:03 localhost kernel: ? qla27xx_walk_template+0xb1/0x1b0 [qla2xxx]
Sep 8 22:26:03 localhost kernel: ? qla27xx_execute_fwdt_template+0x12a/0x160
[qla2xxx]
Sep 8 22:26:03 localhost kernel: ? qla27xx_fwdump+0xa0/0x1c0 [qla2xxx]
Sep 8 22:26:03 localhost kernel: ? qla2xxx_pci_mmio_enabled+0xfb/0x120
[qla2xxx]
Sep 8 22:26:03 localhost kernel: ? report_mmio_enabled+0x44/0x80
Sep 8 22:26:03 localhost kernel: ? report_slot_reset+0x80/0x80
Sep 8 22:26:03 localhost kernel: ? pci_walk_bus+0x70/0x90
Sep 8 22:26:03 localhost kernel: ? aer_dev_correctable_show+0xc0/0xc0
Sep 8 22:26:03 localhost kernel: ? pcie_do_recovery+0x1bb/0x240
Sep 8 22:26:03 localhost kernel: ? aer_recover_work_func+0xaa/0xd0
Sep 8 22:26:03 localhost kernel: ? process_one_work+0x1a7/0x360
..
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-8041:22: detected PCI
disconnect.
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-107ff:22:
qla27xx_fwdt_entry_t262: dump ram MB failed. Area 5h start 198013h end 198013h
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-107ff:22: Unable to
capture FW dump
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-1015:22: cmd=0x0,
waited 5221 msecs
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-680d:22: mmio
enabled returning.
Sep 8 22:26:03 localhost kernel: qla2xxx [0000:42:00.2]-d04c:22: MBX
Command timeout for cmd 0, iocontrol=ffffffff jiffies=10140f2e5
mb[0-3]=[0xffff 0xffff 0xffff 0xffff]
Link: https://lore.kernel.org/r/20220110050218.3958-6-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix warning message due to adisc being flushed. Linux kernel triggered a
warning message where a different error code type is not matching up with
the expected type. Add additional translation of one error code type to
another.
WARNING: CPU: 2 PID: 1131623 at drivers/scsi/qla2xxx/qla_init.c:498
qla2x00_async_adisc_sp_done+0x294/0x2b0 [qla2xxx]
CPU: 2 PID: 1131623 Comm: drmgr Not tainted 5.13.0-rc1-autotest #1
..
GPR28: c000000aaa9c8890 c0080000079ab678 c00000140a104800 c00000002bd19000
NIP [c00800000790857c] qla2x00_async_adisc_sp_done+0x294/0x2b0 [qla2xxx]
LR [c008000007908578] qla2x00_async_adisc_sp_done+0x290/0x2b0 [qla2xxx]
Call Trace:
[c00000001cdc3620] [c008000007908578] qla2x00_async_adisc_sp_done+0x290/0x2b0 [qla2xxx] (unreliable)
[c00000001cdc3710] [c0080000078f3080] __qla2x00_abort_all_cmds+0x1b8/0x580 [qla2xxx]
[c00000001cdc3840] [c0080000078f589c] qla2x00_abort_all_cmds+0x34/0xd0 [qla2xxx]
[c00000001cdc3880] [c0080000079153d8] qla2x00_abort_isp_cleanup+0x3f0/0x570 [qla2xxx]
[c00000001cdc3920] [c0080000078fb7e8] qla2x00_remove_one+0x3d0/0x480 [qla2xxx]
[c00000001cdc39b0] [c00000000071c274] pci_device_remove+0x64/0x120
[c00000001cdc39f0] [c0000000007fb818] device_release_driver_internal+0x168/0x2a0
[c00000001cdc3a30] [c00000000070e304] pci_stop_bus_device+0xb4/0x100
[c00000001cdc3a70] [c00000000070e4f0] pci_stop_and_remove_bus_device+0x20/0x40
[c00000001cdc3aa0] [c000000000073940] pci_hp_remove_devices+0x90/0x130
[c00000001cdc3b30] [c0080000070704d0] disable_slot+0x38/0x90 [rpaphp] [
c00000001cdc3b60] [c00000000073eb4c] power_write_file+0xcc/0x180
[c00000001cdc3be0] [c0000000007354bc] pci_slot_attr_store+0x3c/0x60
[c00000001cdc3c00] [c00000000055f820] sysfs_kf_write+0x60/0x80 [c00000001cdc3c20]
[c00000000055df10] kernfs_fop_write_iter+0x1a0/0x290
[c00000001cdc3c70] [c000000000447c4c] new_sync_write+0x14c/0x1d0
[c00000001cdc3d10] [c00000000044b134] vfs_write+0x224/0x330
[c00000001cdc3d60] [c00000000044b3f4] ksys_write+0x74/0x130
[c00000001cdc3db0] [c00000000002df70] system_call_exception+0x150/0x2d0
[c00000001cdc3e10] [c00000000000d45c] system_call_common+0xec/0x278
Link: https://lore.kernel.org/r/20220110050218.3958-5-njavali@marvell.com
Cc: stable@vger.kernel.org
Reported-by: Abdul Haleem <abdhalee@linux.vnet.ibm.com>
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Fix stuck sessions in get port database. When a thread is in the process of
re-establishing a session, a flag is set to prevent multiple threads /
triggers from doing the same task. This flag was left on, where any attempt
to relogin was locked out. Clear this flag, if the attempt has failed.
Link: https://lore.kernel.org/r/20220110050218.3958-4-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Quinn Tran <qutran@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The timeout handler and the done function are racing. When
qla2x00_async_iocb_timeout() starts to run it can be preempted by the
normal response path (via the firmware?). qla24xx_async_gpsc_sp_done()
releases the SRB unconditionally. When scheduling back to
qla2x00_async_iocb_timeout() qla24xx_async_abort_cmd() will access an freed
sp->qpair pointer:
qla2xxx [0000:83:00.0]-2871:0: Async-gpsc timeout - hdl=63d portid=234500 50:06:0e:80:08:77:b6:21.
qla2xxx [0000:83:00.0]-2853:0: Async done-gpsc res 0, WWPN 50:06:0e:80:08:77:b6:21
qla2xxx [0000:83:00.0]-2854:0: Async-gpsc OUT WWPN 20:45:00:27:f8:75:33:00 speeds=2c00 speed=0400.
qla2xxx [0000:83:00.0]-28d8:0: qla24xx_handle_gpsc_event 50:06:0e:80:08:77:b6:21 DS 7 LS 6 rc 0 login 1|1 rscn 1|0 lid 5
BUG: unable to handle kernel NULL pointer dereference at 0000000000000004
IP: qla24xx_async_abort_cmd+0x1b/0x1c0 [qla2xxx]
Obvious solution to this is to introduce a reference counter. One reference
is taken for the normal code path (the 'good' case) and one for the timeout
path. As we always race between the normal good case and the timeout/abort
handler we need to serialize it. Also we cannot assume any order between
the handlers. Since this is slow path we can use proper synchronization via
locks.
When we are able to cancel a timer (del_timer returns 1) we know there
can't be any error handling in progress because the timeout handler hasn't
expired yet, thus we can safely decrement the refcounter by one.
If we are not able to cancel the timer, we know an abort handler is
running. We have to make sure we call sp->done() in the abort handlers
before calling kref_put().
Link: https://lore.kernel.org/r/20220110050218.3958-3-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Co-developed-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Move common open-coded asynchronous command initializing code such as
setting up the timer and the done callback into one function. This is a
preparation step and allows us later on to change the low level error flow
handling at a central place.
Link: https://lore.kernel.org/r/20220110050218.3958-2-njavali@marvell.com
Cc: stable@vger.kernel.org
Reviewed-by: Himanshu Madhani <himanshu.madhani@oracle.com>
Signed-off-by: Daniel Wagner <dwagner@suse.de>
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL. So, if it fails, the 32-bit case will also fail
for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lore.kernel.org/linux-kernel/YL3vSPK5DXTNvgdx@infradead.org/#t
Link: https://lore.kernel.org/r/5663cef9b54004fa56cca7ce65f51eadfc3ecddb.1642238127.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL. So, if it fails, the 32-bit case will also fail
for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lore.kernel.org/linux-kernel/YL3vSPK5DXTNvgdx@infradead.org/#t
Link: https://lore.kernel.org/r/1bf2d3660178b0e6f172e5208bc0bd68d31d9268.1642237482.git.christophe.jaillet@wanadoo.fr
Acked-by: John Garry <john.garry@huawei.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
As stated in [1], dma_set_mask() with a 64-bit mask never fails if
dev->dma_mask is non-NULL. So, if it fails, the 32-bit case will also fail
for the same reason.
Simplify code and remove some dead code accordingly.
[1]: https://lore.kernel.org/linux-kernel/YL3vSPK5DXTNvgdx@infradead.org/#t
Link: https://lore.kernel.org/r/dbbe8671ca760972d80f8d35f3170b4609bee368.1642236763.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The bnx2fc_destroy() functions are removing the interface before calling
destroy_work. This results multiple WARNings from sysfs_remove_group() as
the controller rport device attributes are removed too early.
Replace the fcoe_port's destroy_work queue. It's not needed.
The problem is easily reproducible with the following steps.
Example:
$ dmesg -w &
$ systemctl enable --now fcoe
$ fipvlan -s -c ens2f1
$ fcoeadm -d ens2f1.802
[ 583.464488] host2: libfc: Link down on port (7500a1)
[ 583.472651] bnx2fc: 7500a1 - rport not created Yet!!
[ 583.490468] ------------[ cut here ]------------
[ 583.538725] sysfs group 'power' not found for kobject 'rport-2:0-0'
[ 583.568814] WARNING: CPU: 3 PID: 192 at fs/sysfs/group.c:279 sysfs_remove_group+0x6f/0x80
[ 583.607130] Modules linked in: dm_service_time 8021q garp mrp stp llc bnx2fc cnic uio rpcsec_gss_krb5 auth_rpcgss nfsv4 ...
[ 583.942994] CPU: 3 PID: 192 Comm: kworker/3:2 Kdump: loaded Not tainted 5.14.0-39.el9.x86_64 #1
[ 583.984105] Hardware name: HP ProLiant DL120 G7, BIOS J01 07/01/2013
[ 584.016535] Workqueue: fc_wq_2 fc_rport_final_delete [scsi_transport_fc]
[ 584.050691] RIP: 0010:sysfs_remove_group+0x6f/0x80
[ 584.074725] Code: ff 5b 48 89 ef 5d 41 5c e9 ee c0 ff ff 48 89 ef e8 f6 b8 ff ff eb d1 49 8b 14 24 48 8b 33 48 c7 c7 ...
[ 584.162586] RSP: 0018:ffffb567c15afdc0 EFLAGS: 00010282
[ 584.188225] RAX: 0000000000000000 RBX: ffffffff8eec4220 RCX: 0000000000000000
[ 584.221053] RDX: ffff8c1586ce84c0 RSI: ffff8c1586cd7cc0 RDI: ffff8c1586cd7cc0
[ 584.255089] RBP: 0000000000000000 R08: 0000000000000000 R09: ffffb567c15afc00
[ 584.287954] R10: ffffb567c15afbf8 R11: ffffffff8fbe7f28 R12: ffff8c1486326400
[ 584.322356] R13: ffff8c1486326480 R14: ffff8c1483a4a000 R15: 0000000000000004
[ 584.355379] FS: 0000000000000000(0000) GS:ffff8c1586cc0000(0000) knlGS:0000000000000000
[ 584.394419] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 584.421123] CR2: 00007fe95a6f7840 CR3: 0000000107674002 CR4: 00000000000606e0
[ 584.454888] Call Trace:
[ 584.466108] device_del+0xb2/0x3e0
[ 584.481701] device_unregister+0x13/0x60
[ 584.501306] bsg_unregister_queue+0x5b/0x80
[ 584.522029] bsg_remove_queue+0x1c/0x40
[ 584.541884] fc_rport_final_delete+0xf3/0x1d0 [scsi_transport_fc]
[ 584.573823] process_one_work+0x1e3/0x3b0
[ 584.592396] worker_thread+0x50/0x3b0
[ 584.609256] ? rescuer_thread+0x370/0x370
[ 584.628877] kthread+0x149/0x170
[ 584.643673] ? set_kthread_struct+0x40/0x40
[ 584.662909] ret_from_fork+0x22/0x30
[ 584.680002] ---[ end trace 53575ecefa942ece ]---
Link: https://lore.kernel.org/r/20220115040044.1013475-1-jmeneghi@redhat.com
Fixes: 0cbf32e1681d ("[SCSI] bnx2fc: Avoid calling bnx2fc_if_destroy with unnecessary locks")
Tested-by: Guangwu Zhang <guazhang@redhat.com>
Co-developed-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: John Meneghini <jmeneghi@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Suppose we have an environment with a number of non-NPIV FCP devices
(virtual HBAs / FCP devices / zfcp "adapter"s) sharing the same physical
FCP channel (HBA port) and its I_T nexus. Plus a number of storage target
ports zoned to such shared channel. Now one target port logs out of the
fabric causing an RSCN. Zfcp reacts with an ADISC ELS and subsequent port
recovery depending on the ADISC result. This happens on all such FCP
devices (in different Linux images) concurrently as they all receive a copy
of this RSCN. In the following we look at one of those FCP devices.
Requests other than FSF_QTCB_FCP_CMND can be slow until they get a
response.
Depending on which requests are affected by slow responses, there are
different recovery outcomes. Here we want to fix failed recoveries on port
or adapter level by avoiding recovery requests that can be slow.
We need the cached N_Port_ID for the remote port "link" test with ADISC.
Just before sending the ADISC, we now intentionally forget the old cached
N_Port_ID. The idea is that on receiving an RSCN for a port, we have to
assume that any cached information about this port is stale. This forces a
fresh new GID_PN [FC-GS] nameserver lookup on any subsequent recovery for
the same port. Since we typically can still communicate with the nameserver
efficiently, we now reach steady state quicker: Either the nameserver still
does not know about the port so we stop recovery, or the nameserver already
knows the port potentially with a new N_Port_ID and we can successfully and
quickly perform open port recovery. For the one case, where ADISC returns
successfully, we re-initialize port->d_id because that case does not
involve any port recovery.
This also solves a problem if the storage WWPN quickly logs into the fabric
again but with a different N_Port_ID. Such as on virtual WWPN takeover
during target NPIV failover.
[https://www.redbooks.ibm.com/abstracts/redp5477.html] In that case the
RSCN from the storage FDISC was ignored by zfcp and we could not
successfully recover the failover. On some later failback on the storage,
we could have been lucky if the virtual WWPN got the same old N_Port_ID
from the SAN switch as we still had cached. Then the related RSCN
triggered a successful port reopen recovery. However, there is no
guarantee to get the same N_Port_ID on NPIV FDISC.
Even though NPIV-enabled FCP devices are not affected by this problem, this
code change optimizes recovery time for gone remote ports as a side effect.
The timely drop of cached N_Port_IDs prevents unnecessary slow open port
attempts.
While the problem might have been in code before v2.6.32 commit
799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp") this fix
depends on the gid_pn_work introduced with that commit, so we mark it as
culprit to satisfy fix dependencies.
Note: Point-to-point remote port is already handled separately and gets its
N_Port_ID from the cached peer_d_id. So resetting port->d_id in general
does not affect PtP.
Link: https://lore.kernel.org/r/20220118165803.3667947-1-maier@linux.ibm.com
Fixes: 799b76d09aee ("[SCSI] zfcp: Decouple gid_pn requests from erp")
Cc: <stable@vger.kernel.org> #2.6.32+
Suggested-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
According to the comment in check_fw_ready() we should not check the
IOP1_READY field in register SCRATCH_PAD_1 for 8008 or 8009 controllers.
However we check this very field in process_oq() for processing the highest
index interrupt vector. The highest interrupt vector is checked as the FW
is programmed to signal fatal errors through this irq.
Change that function to not check IOP1_READY for those mentioned
controllers, but do check ILA_READY in both cases.
The reason I assume that this was not hit earlier was because we always
allocated 64 MSI(X), and just did not pass the vector index check in
process_oq(), i.e. the handler never ran for vector index 63.
Link: https://lore.kernel.org/r/1642508105-95432-1-git-send-email-john.garry@huawei.com
Tested-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@opensource.wdc.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If FCoE is not configured, libfc/libfcoe keeps on retrying FLOGI and after
3 retries driver does a context reset and tries fipvlan again. This leads
to context reset message flooding the logs. Hence ratelimit the message to
prevent flooding the logs.
Link: https://lore.kernel.org/r/20220117135311.6256-4-njavali@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Hung task call trace was seen during LOGO processing.
[ 974.309060] [0000:00:00.0]:[qedf_eh_device_reset:868]: 1:0:2:0: LUN RESET Issued...
[ 974.309065] [0000:00:00.0]:[qedf_initiate_tmf:2422]: tm_flags 0x10 sc_cmd 00000000c16b930f op = 0x2a target_id = 0x2 lun=0
[ 974.309178] [0000:00:00.0]:[qedf_initiate_tmf:2431]: portid=016900 tm_flags =LUN RESET
[ 974.309222] [0000:00:00.0]:[qedf_initiate_tmf:2438]: orig io_req = 00000000ec78df8f xid = 0x180 ref_cnt = 1.
[ 974.309625] host1: rport 016900: Received LOGO request while in state Ready
[ 974.309627] host1: rport 016900: Delete port
[ 974.309642] host1: rport 016900: work event 3
[ 974.309644] host1: rport 016900: lld callback ev 3
[ 974.313243] [0000:61:00.2]:[qedf_execute_tmf:2383]:1: fcport is uploading, not executing flush.
[ 974.313295] [0000:61:00.2]:[qedf_execute_tmf:2400]:1: task mgmt command success...
[ 984.031088] INFO: task jbd2/dm-15-8:7645 blocked for more than 120 seconds.
[ 984.031136] Not tainted 4.18.0-305.el8.x86_64 #1
[ 984.031166] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[ 984.031209] jbd2/dm-15-8 D 0 7645 2 0x80004080
[ 984.031212] Call Trace:
[ 984.031222] __schedule+0x2c4/0x700
[ 984.031230] ? unfreeze_partials.isra.83+0x16e/0x1a0
[ 984.031233] ? bit_wait_timeout+0x90/0x90
[ 984.031235] schedule+0x38/0xa0
[ 984.031238] io_schedule+0x12/0x40
[ 984.031240] bit_wait_io+0xd/0x50
[ 984.031243] __wait_on_bit+0x6c/0x80
[ 984.031248] ? free_buffer_head+0x21/0x50
[ 984.031251] out_of_line_wait_on_bit+0x91/0xb0
[ 984.031257] ? init_wait_var_entry+0x50/0x50
[ 984.031268] jbd2_journal_commit_transaction+0x112e/0x19f0 [jbd2]
[ 984.031280] kjournald2+0xbd/0x270 [jbd2]
[ 984.031284] ? finish_wait+0x80/0x80
[ 984.031291] ? commit_timeout+0x10/0x10 [jbd2]
[ 984.031294] kthread+0x116/0x130
[ 984.031300] ? kthread_flush_work_fn+0x10/0x10
[ 984.031305] ret_from_fork+0x1f/0x40
There was a ref count issue when LOGO is received during TMF. This leads to
one of the I/Os hanging with the driver. Fix the ref count.
Link: https://lore.kernel.org/r/20220117135311.6256-3-njavali@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Call trace seen when creating NPIV ports, only 32 out of 64 show online.
stag work was not initialized for vport, hence initialize the stag work.
WARNING: CPU: 8 PID: 645 at kernel/workqueue.c:1635 __queue_delayed_work+0x68/0x80
CPU: 8 PID: 645 Comm: kworker/8:1 Kdump: loaded Tainted: G IOE --------- --
4.18.0-348.el8.x86_64 #1
Hardware name: Dell Inc. PowerEdge MX740c/0177V9, BIOS 2.12.2 07/09/2021
Workqueue: events fc_lport_timeout [libfc]
RIP: 0010:__queue_delayed_work+0x68/0x80
Code: 89 b2 88 00 00 00 44 89 82 90 00 00 00 48 01 c8 48 89 42 50 41 81
f8 00 20 00 00 75 1d e9 60 24 07 00 44 89 c7 e9 98 f6 ff ff <0f> 0b eb
c5 0f 0b eb a1 0f 0b eb a7 0f 0b eb ac 44 89 c6 e9 40 23
RSP: 0018:ffffae514bc3be40 EFLAGS: 00010006
RAX: ffff8d25d6143750 RBX: 0000000000000202 RCX: 0000000000000002
RDX: ffff8d2e31383748 RSI: ffff8d25c000d600 RDI: ffff8d2e31383788
RBP: ffff8d2e31380de0 R08: 0000000000002000 R09: ffff8d2e31383750
R10: ffffffffc0c957e0 R11: ffff8d2624800000 R12: ffff8d2e31380a58
R13: ffff8d2d915eb000 R14: ffff8d25c499b5c0 R15: ffff8d2e31380e18
FS: 0000000000000000(0000) GS:ffff8d2d1fb00000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 000055fd0484b8b8 CR3: 00000008ffc10006 CR4: 00000000007706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
queue_delayed_work_on+0x36/0x40
qedf_elsct_send+0x57/0x60 [qedf]
fc_lport_enter_flogi+0x90/0xc0 [libfc]
fc_lport_timeout+0xb7/0x140 [libfc]
process_one_work+0x1a7/0x360
? create_worker+0x1a0/0x1a0
worker_thread+0x30/0x390
? create_worker+0x1a0/0x1a0
kthread+0x116/0x130
? kthread_flush_work_fn+0x10/0x10
ret_from_fork+0x35/0x40
---[ end trace 008f00f722f2c2ff ]--
Initialize stag work for all the vports.
Link: https://lore.kernel.org/r/20220117135311.6256-2-njavali@marvell.com
Signed-off-by: Saurav Kashyap <skashyap@marvell.com>
Signed-off-by: Nilesh Javali <njavali@marvell.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
devm_kstrdup() returns pointer to allocated string on success, NULL on
failure. So it is better to check the return value of it.
Link: https://lore.kernel.org/r/tencent_4257E15D4A94FF9020DDCC4BB9B21C041408@qq.com
Reviewed-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Xiaoke Wang <xkernel.wang@foxmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
iscsit_tpg_check_network_portal() has nested for_each loops and is supposed
to return true when a match is found. However, the tpg loop will still
continue after existing the tpg_np loop. If this tpg_np is not the last the
match value will be changed.
Break the outer loop after finding a match and make sure the np under each
tpg is unique.
Link: https://lore.kernel.org/r/20220111054742.19582-1-mingzhe.zou@easystack.cn
Signed-off-by: ZouMingzhe <mingzhe.zou@easystack.cn>
Reviewed-by: Mike Christie <michael.christie@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
GFP_KERNEL/GFP_DMA can't be used under a spin lock. According the comment,
els_ios_lock is used to protect els ios list so we can move down the spin
lock to avoid using this flag under the lock.
Link: https://lore.kernel.org/r/20220111012441.3232527-1-yangyingliang@huawei.com
Fixes: 8f406ef72859 ("scsi: elx: libefc: Extended link Service I/O handling")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: James Smart <jsmart2021@gmail.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
Maxime Ripard
Daniel Vetter
Manasi Navare
Douglas Gilbert
Dan Carpenter
Tong Zhang
Colin Ian King
Kiwoong Kim
Nilesh Javali
Joe Carnuccio
Saurav Kashyap
Quinn Tran
Arun Easi
Shreyas Deodhar
Bikash Hazarika
Daniel Wagner
Christophe JAILLET
John Meneghini
Steffen Maier
John Garry
Xiaoke Wang
ZouMingzhe
Yang Yingliang