| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
Compile-testing the driver without CONFIG_COMMON_CLK causes
a link failure:
arm-linux-gnueabi-ld: drivers/devfreq/sun8i-a33-mbus.o: in function `sun8i_a33_mbus_remove':
sun8i-a33-mbus.c:(.text+0x450): undefined reference to `clk_rate_exclusive_put'
arm-linux-gnueabi-ld: sun8i-a33-mbus.c:(.text+0x460): undefined reference to `clk_rate_exclusive_put'
arm-linux-gnueabi-ld: drivers/devfreq/sun8i-a33-mbus.o: in function `sun8i_a33_mbus_probe':
sun8i-a33-mbus.c:(.text+0x85c): undefined reference to `clk_rate_exclusive_get'
arm-linux-gnueabi-ld: sun8i-a33-mbus.c:(.text+0x878): undefined reference to `clk_rate_exclusive_get'
Fixes: 8bfd4858b4bb ("PM / devfreq: Add a driver for the sun8i/sun50i MBUS")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
|
|
Zero-initialize memory for new map's value in function nsim_bpf_map_alloc
since it may cause a potential kernel information leak issue, as follows:
1. nsim_bpf_map_alloc calls nsim_map_alloc_elem to allocate elements for
a new map.
2. nsim_map_alloc_elem uses kmalloc to allocate map's value, but doesn't
zero it.
3. A user application can use IOCTL BPF_MAP_LOOKUP_ELEM to get specific
element's information in the map.
4. The kernel function map_lookup_elem will call bpf_map_copy_value to get
the information allocated at step-2, then use copy_to_user to copy to the
user buffer.
This can only leak information for an array map.
Fixes: 395cacb5f1a0 ("netdevsim: bpf: support fake map offload")
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Haimin Zhang <tcs.kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215111530.72103-1-tcs.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Unfortunately, with the blamed commit I also added a side effect in the
ethtool stats shown. Because I added two more fields in the per channel
structure without verifying if its size is used in any way, part of the
ethtool statistics were off by 2.
Fix this by not looking up the size of the structure but instead on a
fixed value kept in a macro.
Fixes: fc398bec0387 ("net: dpaa2: add adaptive interrupt coalescing")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Link: https://lore.kernel.org/r/20211215105831.290070-1-ioana.ciornei@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add UTS_RELEASE and show timestamp the same way for consistency.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211215174524.1742389-2-robdclark@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Implement plane's atomic_print_state() callback, printing DPU-specific
plane state: blending stage, SSPP and multirect mode and index.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211215160912.2715956-2-dmitry.baryshkov@linaro.org
[DB: marked pdpu and pstate as const]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Implement CRTC's atomic_print_state() callback, printing DPU-specific
CRTC state (LM, CTL and DSPP ids).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20211215160912.2715956-1-dmitry.baryshkov@linaro.org
[DB: marked cstate as const]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The "dp_bridge" pointer is allocated with devm_kzalloc() so it will be
freed automatically. Kfreeing it here will only lead to a double free.
Fixes: 8a3b4c17f863 ("drm/msm/dp: employ bridge mechanism for display enable and disable")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20211215114900.GD14552@kili
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Squash dpu_debugfs_setup_regset32() into dpu_debugfs_create_regset32().
it makes little sense to have separate function to just setup the
structure.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-8-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
DRM code handles removing all debugfs recursively. Drop CRTC-specific
code to perform that.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
DRM code handles removing all debugfs recursively. Drop plane-specific
code to perform that.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-6-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Proper support for the 'default_scaling' debugfs file was removed during
DPU driver pre-merge cleanup. Remove leftover file.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Change \t to \n in the print format to stop putting all SSPP status in a
single line. Splitting it to one SSPP per line is much more readable.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
Make safe_status debugfs fs file actually return safe status rather than
danger status data.
Fixes: 25fdd5933e4c ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
The disable_danger debugfs file is not related to a single plane.
Instead it is used by all registered planes. Move it from plane subtree
to the global subtree next to danger_status and safe_status files,
so that the new file supplements them.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211201222633.2476780-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
|
|
During disconnect USB-3 ports often go via SS.Inactive link error state
before the missing terminations are noticed, and link finally goes to
RxDetect state
Avoid immediately warm-resetting ports in SS.Inactive state.
Let ports settle for a while and re-read the link status a few times 20ms
apart to see if the ports transitions out of SS.Inactive.
According to USB 3.x spec 7.5.2, a port in SS.Inactive should
automatically check for missing far-end receiver termination every
12 ms (SSInactiveQuietTimeout)
The futile multiple warm reset retries of a disconnected device takes
a lot of time, also the resetting of a removed devices has caused cases
where the reset bit got stuck for a long time on xHCI roothub.
This lead to issues in detecting new devices connected to the same port
shortly after.
Tested-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20211210111653.1378381-1-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add the missing unlock before return from function xenhcd_urb_request_done()
and xenhcd_conn_notify() in the error handling case.
Fixes: 494ed3997d75 ("usb: Introduce Xen pvUSB frontend (xen hcd)")
Reported-by: Hulk Robot <hulkci@huawei.com>
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20211215035805.375244-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In case of probe defer, a message is logged for resets and clocks. Use
dev_err_probe to log the message only when error code is not -517.
Simplify phy, regulators and drd probe defer handling with dev_err_probe().
Then, take benefit of devices_deferred debugfs in case of probe deferral.
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207120829.266837-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In current design, when the tcpm port is unregisterd, the kthread_worker
will be destroyed in the last step. Inside the kthread_destroy_worker(),
the worker will flush all the works and wait for them to end. However, if
one of the works calls hrtimer_start(), this hrtimer will be pending until
timeout even though tcpm port is removed. Once the hrtimer timeout, many
strange kernel dumps appear.
Thus, we can first complete kthread_destroy_worker(), then cancel all the
hrtimers. This will guarantee that no hrtimer is pending at the end.
Fixes: 3ed8e1c2ac99 ("usb: typec: tcpm: Migrate workqueue to RT priority for processing events")
cc: <stable@vger.kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Xu Yang <xu.yang_2@nxp.com>
Link: https://lore.kernel.org/r/20211209101507.499096-1-xu.yang_2@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch puts content of cdnsp_gadget_pullup function inside
spin_lock_irqsave and spin_lock_restore section.
This construction is required here to keep the data consistency,
otherwise some data can be changed e.g. from interrupt context.
Fixes: 3d82904559f4 ("usb: cdnsp: cdns3 Add main part of Cadence USBSSP DRD Driver")
Reported-by: Ken (Jian) He <jianhe@ambarella.com>
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
--
Changelog:
v2:
- added disable_irq/enable_irq as sugester by Peter Chen
drivers/usb/cdns3/cdnsp-gadget.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Link: https://lore.kernel.org/r/20211214045527.26823-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This device doesn't work well with LPM, losing connectivity intermittently.
Disable LPM to resolve the issue.
Reviewed-by: <markpearson@lenovo.com>
Signed-off-by: Jimmy Wang <wangjm221@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211214012652.4898-1-wangjm221@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
AMD's Yellow Carp platform has few more XHCI controllers,
enable the runtime power management support for the same.
Signed-off-by: Nehal Bakulchandra Shah <Nehal-Bakulchandra.shah@amd.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20211215093216.1839065-1-Nehal-Bakulchandra.shah@amd.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If an architecture does not support 64 bit dma addresses then testing
for an expected dma address >= 0x100000000 will fail.
Fixes: e0d072782c73 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Signed-off-by: Frank Rowand <frank.rowand@sony.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211212221852.233295-1-frowand.list@gmail.com
|
|
The struct device variable "dev_bogus" was triggering this warning
on a PowerPC build:
drivers/of/unittest.c: In function 'of_unittest_dma_ranges_one.constprop':
[...] >> The frame size of 1424 bytes is larger than 1024 bytes
[-Wframe-larger-than=]
This variable is now dynamically allocated.
Fixes: e0d072782c734 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Jim Quinlan <jim2101024@gmail.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Frank Rowand <frank.rowand@sony.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20211210184636.7273-2-jim2101024@gmail.com
|
|
The TPS68470 PMIC provides Clocks, GPIOs and Regulators. At present in
the kernel the Regulators and Clocks are controlled by an OpRegion
driver designed to work with power control methods defined in ACPI, but
some platforms lack those methods, meaning drivers need to be able to
consume the resources of these chips through the usual frameworks.
This commit adds a driver for the regulators provided by the tps68470,
and is designed to bind to the platform_device registered by the
intel_skl_int3472 module.
This is based on this out of tree driver written by Intel:
https://github.com/intel/linux-intel-lts/blob/4.14/base/drivers/regulator/tps68470-regulator.c
with various cleanups added.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-6-hdegoede@redhat.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since pci_alloc_p2pmem() has already called rcu_read_lock(), we're in an
RCU read-side critical section and don't need to take the lock again. Use
percpu_ref_tryget_live_rcu() instead of percpu_ref_tryget_live() to save a
few cycles.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/ab80164f4d5b32f9e6240aa4863c3a147ff9c89f.1635974126.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: Logan Gunthorpe <logang@deltatee.com>
|
|
Signed tag for the immutable platform-drivers-x86-int3472 branch
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches.
|
|
Signed tag for the immutable platform-drivers-x86-int3472 branch
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches required so that the tps68570 regulator
driver can be applied.
|
|
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
introduced support to use high baudrate with Fintek SuperIO UARTs. It'll
change clocksources when the UART probed.
But when user add kernel parameter "console=ttyS0,115200 console=tty0" to make
the UART as console output, the console will output garbled text after the
following kernel message.
[ 3.681188] Serial: 8250/16550 driver, 32 ports, IRQ sharing enabled
The issue is occurs in following step:
probe_setup_port() -> fintek_8250_goto_highspeed()
It change clocksource from 115200 to 921600 with wrong time, it should change
clocksource in set_termios() not in probed. The following 3 patches are
implemented change clocksource in fintek_8250_set_termios().
Commit 58178914ae5b ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81216H")
Commit 195638b6d44f ("serial: 8250_fintek: UART dynamic clocksource on Fintek F81866")
Commit 423d9118c624 ("serial: 8250_fintek: Add F81966 Support")
Due to the high baud rate had implemented above 3 patches and the patch
Commit fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
is bugged, So this patch will remove it.
Fixes: fab8a02b73eb ("serial: 8250_fintek: Enable high speed mode on Fintek F81866")
Signed-off-by: Ji-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Link: https://lore.kernel.org/r/20211215075835.2072-1-hpeter+linux_kernel@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
syzbot is reporting that an unprivileged user who logged in from tty
console can crash the system using a reproducer shown below [1], for
n_hdlc_tty_wakeup() is synchronously calling n_hdlc_send_frames().
----------
#include <sys/ioctl.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
const int disc = 0xd;
ioctl(1, TIOCSETD, &disc);
while (1) {
ioctl(1, TCXONC, 0);
write(1, "", 1);
ioctl(1, TCXONC, 1); /* Kernel panic - not syncing: scheduling while atomic */
}
}
----------
Linus suspected that "struct tty_ldisc"->ops->write_wakeup() must not
sleep, and Jiri confirmed it from include/linux/tty_ldisc.h. Thus, defer
n_hdlc_send_frames() from n_hdlc_tty_wakeup() to a WQ context like
net/nfc/nci/uart.c does.
Link: https://syzkaller.appspot.com/bug?extid=5f47a8cea6a12b77a876 [1]
Reported-by: syzbot <syzbot+5f47a8cea6a12b77a876@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Analyzed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Confirmed-by: Jiri Slaby <jirislaby@kernel.org>
Reviewed-by: Fabio M. De Francesco <fmdefrancesco@gmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Link: https://lore.kernel.org/r/40de8b7e-a3be-4486-4e33-1b1d1da452f8@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Like other SATA controller chips in the Marvell 88SE91xx series, the
Marvell 88SE9125 has the same DMA requester ID hardware bug that prevents
it from working under IOMMU. Add it to the list of devices that need the
quirk.
Without this patch, device initialization fails with DMA errors:
ata8: softreset failed (1st FIS failed)
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Write NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
DMAR: DRHD: handling fault status reg 2
DMAR: [DMA Read NO_PASID] Request device [03:00.1] fault addr 0xfffc0000 [fault reason 0x02] Present bit in context entry is clear
After applying the patch, the controller can be successfully initialized:
ata8: SATA link up 1.5 Gbps (SStatus 113 SControl 330)
ata8.00: ATAPI: PIONEER BD-RW BDR-207M, 1.21, max UDMA/100
ata8.00: configured for UDMA/100
scsi 7:0:0:0: CD-ROM PIONEER BD-RW BDR-207M 1.21 PQ: 0 ANSI: 5
Link: https://lore.kernel.org/r/YahpKVR+McJVDdkD@work
Reported-by: Sam Bingner <sam@bingner.com>
Tested-by: Sam Bingner <sam@bingner.com>
Tested-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Yifeng Li <tomli@tomli.me>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Krzysztof Wilczyński <kw@linux.com>
Cc: stable@vger.kernel.org
|
|
The MDIO bus speed must be initialized before talking to the PHY the first
time in order to avoid talking to it using a speed that the PHY doesn't
support.
This fixes HW initialization error -17 (IXGBE_ERR_PHY_ADDR_INVALID) on
Denverton CPUs (a.k.a. the Atom C3000 family) on ports with a 10Gb network
plugged in. On those devices, HLREG0[MDCSPD] resets to 1, which combined
with the 10Gb network results in a 24MHz MDIO speed, which is apparently
too fast for the connected PHY. PHY register reads over MDIO bus return
garbage, leading to initialization failure.
Reproduced with Linux kernel 4.19 and 5.15-rc7. Can be reproduced using
the following setup:
* Use an Atom C3000 family system with at least one X552 LAN on the SoC
* Disable PXE or other BIOS network initialization if possible
(the interface must not be initialized before Linux boots)
* Connect a live 10Gb Ethernet cable to an X550 port
* Power cycle (not reset, doesn't always work) the system and boot Linux
* Observe: ixgbe interfaces w/ 10GbE cables plugged in fail with error -17
Fixes: e84db7272798 ("ixgbe: Introduce function to control MDIO speed")
Signed-off-by: Cyril Novikov <cnovikov@lynx.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Commit 25058d1c725c ("dm integrity: use bvec_kmap_local in
__journal_read_write") didn't account for __journal_read_write() later
adding the biovec's bv_offset. As such using bvec_kmap_local() caused
the start of the biovec to be skipped.
Trivial test that illustrates data corruption:
# integritysetup format /dev/pmem0
# integritysetup open /dev/pmem0 integrityroot
# mkfs.xfs /dev/mapper/integrityroot
...
bad magic number
bad magic number
Metadata corruption detected at xfs_sb block 0x0/0x1000
libxfs_writebufr: write verifer failed on xfs_sb bno 0x0/0x1000
releasing dirty buffer (bulk) to free list!
Fix this by using kmap_local_page() instead of bvec_kmap_local() in
__journal_read_write().
Fixes: 25058d1c725c ("dm integrity: use bvec_kmap_local in __journal_read_write")
Reported-by: Tony Asleson <tasleson@redhat.com>
Reviewed-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Commit a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0
Gbps support") introduced suppression of the advertisement of NBASE-T
speeds by default, according to Todd Fujinaka to accommodate customers
with network switches which could not cope with advertised NBASE-T
speeds, as posted in the E1000-devel mailing list:
https://sourceforge.net/p/e1000/mailman/message/37106269/
However, the suppression was not documented at all, nor was how to
enable NBASE-T support.
Properly document the NBASE-T suppression and how to enable NBASE-T
support.
Fixes: a296d665eae1 ("ixgbe: Add ethtool support to enable 2.5 and 5.0 Gbps support")
Reported-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Robert Schlabbach <robert_s@gmx.net>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The LTR maximum value was incorrectly written using the scale from
the LTR minimum value. This would cause incorrect values to be sent,
in cases where the initial calculation lead to different min/max scales.
Fixes: 707abf069548 ("igc: Add initial LTR support")
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In `igbvf_probe`, if register_netdev() fails, the program will go to
label err_hw_init, and then to label err_ioremap. In free_netdev() which
is just below label err_ioremap, there is `list_for_each_entry_safe` and
`netif_napi_del` which aims to delete all entries in `dev->napi_list`.
The program has added an entry `adapter->rx_ring->napi` which is added by
`netif_napi_add` in igbvf_alloc_queues(). However, adapter->rx_ring has
been freed below label err_hw_init. So this a UAF.
In terms of how to patch the problem, we can refer to igbvf_remove() and
delete the entry before `adapter->rx_ring`.
The KASAN logs are as follows:
[ 35.126075] BUG: KASAN: use-after-free in free_netdev+0x1fd/0x450
[ 35.127170] Read of size 8 at addr ffff88810126d990 by task modprobe/366
[ 35.128360]
[ 35.128643] CPU: 1 PID: 366 Comm: modprobe Not tainted 5.15.0-rc2+ #14
[ 35.129789] Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-gc9ba5276e321-prebuilt.qemu.org 04/01/2014
[ 35.131749] Call Trace:
[ 35.132199] dump_stack_lvl+0x59/0x7b
[ 35.132865] print_address_description+0x7c/0x3b0
[ 35.133707] ? free_netdev+0x1fd/0x450
[ 35.134378] __kasan_report+0x160/0x1c0
[ 35.135063] ? free_netdev+0x1fd/0x450
[ 35.135738] kasan_report+0x4b/0x70
[ 35.136367] free_netdev+0x1fd/0x450
[ 35.137006] igbvf_probe+0x121d/0x1a10 [igbvf]
[ 35.137808] ? igbvf_vlan_rx_add_vid+0x100/0x100 [igbvf]
[ 35.138751] local_pci_probe+0x13c/0x1f0
[ 35.139461] pci_device_probe+0x37e/0x6c0
[ 35.165526]
[ 35.165806] Allocated by task 366:
[ 35.166414] ____kasan_kmalloc+0xc4/0xf0
[ 35.167117] foo_kmem_cache_alloc_trace+0x3c/0x50 [igbvf]
[ 35.168078] igbvf_probe+0x9c5/0x1a10 [igbvf]
[ 35.168866] local_pci_probe+0x13c/0x1f0
[ 35.169565] pci_device_probe+0x37e/0x6c0
[ 35.179713]
[ 35.179993] Freed by task 366:
[ 35.180539] kasan_set_track+0x4c/0x80
[ 35.181211] kasan_set_free_info+0x1f/0x40
[ 35.181942] ____kasan_slab_free+0x103/0x140
[ 35.182703] kfree+0xe3/0x250
[ 35.183239] igbvf_probe+0x1173/0x1a10 [igbvf]
[ 35.184040] local_pci_probe+0x13c/0x1f0
Fixes: d4e0fe01a38a0 (igbvf: add new driver to support 82576 virtual functions)
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Letu Ren <fantasquex@gmail.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Move checking condition of VF MAC filter before clearing
or adding MAC filter to VF to prevent potential blackout caused
by removal of necessary and working VF's MAC filter.
Fixes: 1b8b062a99dc ("igb: add VF trust infrastructure")
Signed-off-by: Karen Sornek <karen.sornek@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Pull hyperv fix from Wei Liu:
"Build fix from Randy Dunlap"
* tag 'hyperv-fixes-signed-20211214' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
hv: utils: add PTP_1588_CLOCK to Kconfig to fix build
|
|
The Clock-and-Reset controller resides in a core power domain on NVIDIA
Tegra SoCs. In order to support voltage scaling of the core power domain,
we hook up DVFS-capable clocks to the core GENPD for managing of the
GENPD's performance state based on the clock changes.
Some clocks don't have any specific physical hardware unit that backs
them, like root PLLs and system clock and they have theirs own voltage
requirements. This patch adds new clk-device driver that backs the clocks
and provides runtime PM functionality for them. A virtual clk-device is
created for each such DVFS-capable clock at the clock's registration time
by the new tegra_clk_register() helper. Driver changes clock's device
GENPD performance state based on clk-rate notifications.
In result we have this sequence of events:
1. Clock driver creates virtual device for selective clocks, enables
runtime PM for the created device and registers the clock.
2. Clk-device driver starts to listen to clock rate changes.
3. Something changes clk rate or enables/disables clk.
4. CCF core propagates the change through the clk tree.
5. Clk-device driver gets clock rate-change notification or GENPD core
handles prepare/unprepare of the clock.
6. Clk-device driver changes GENPD performance state on clock rate
change.
7. GENPD driver changes voltage regulator state change.
8. The regulator state is committed to hardware via I2C.
We rely on fact that DVFS is not needed for Tegra I2C and that Tegra I2C
driver already keeps clock always-prepared. Hence I2C subsystem stays
independent from the clk power management and there are no deadlock spots
in the sequence.
Currently all clocks are registered very early during kernel boot when the
device driver core isn't available yet. The clk-device can't be created
at that time. This patch splits the registration of the clocks in two
phases:
1. Register all essential clocks which don't use RPM and are needed
during early boot.
2. Register at a later boot time the rest of clocks.
This patch adds power management support for Tegra20 and Tegra30 clocks.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Peter Geis <pgwipeout@gmail.com> # Ouya T30
Tested-by: Paul Fertser <fercerpav@gmail.com> # PAZ00 T20
Tested-by: Nicolas Chauvet <kwizart@gmail.com> # PAZ00 T20 and TK1 T124
Tested-by: Matt Merhar <mattmerhar@protonmail.com> # Ouya T30
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
When activate_stm_id_vb_detection is enabled, ID and Vbus detection relies
on sensing comparators. This detection needs time to stabilize.
A delay was already applied in dwc2_resume() when reactivating the
detection, but it wasn't done in dwc2_probe().
This patch adds delay after enabling STM ID/VBUS detection. Then, ID state
is good when initializing gadget and host, and avoid to get a wrong
Connector ID Status Change interrupt.
Fixes: a415083a11cc ("usb: dwc2: add support for STM32MP15 SoCs USB OTG HS and FS")
Cc: stable <stable@vger.kernel.org>
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207124510.268841-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Szymon rightly pointed out that the previous check for the endpoint
direction in bRequestType was not looking at only the bit involved, but
rather the whole value. Normally this is ok, but for some request
types, bits other than bit 8 could be set and the check for the endpoint
length could not stall correctly.
Fix that up by only checking the single bit.
Fixes: 153a2d7e3350 ("USB: gadget: detect too-big endpoint 0 requests")
Cc: Felipe Balbi <balbi@kernel.org>
Reported-by: Szymon Heidrich <szymon.heidrich@gmail.com>
Link: https://lore.kernel.org/r/20211214184621.385828-1-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The kernel gained a new interface for drivers to use to combine tail
bump (doorbell) and BQL updates, attempt to use those new interfaces.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The driver had comments to the effect of: This flag should be set before
calling this function. While reviewing code it was found that there were
several violations of this policy, which could introduce hard to find
bugs or races.
Fix the violations of the "VSI DOWN state must be set before calling
ice_down" and make checking the state into code with a WARN_ON.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The kernel provides some prefetch mechanisms to speed up commonly
cold cache line accesses during receive processing. Since these are
software structures it helps to have these strategically placed
prefetches.
Be careful to call BQL prefetch complete only for non XDP queues.
Co-developed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use the netif_tx_* API from netdevice.h which has simpler parameters.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice hardware contains an embedded chip with firmware which can be
updated using devlink flash. The firmware which runs on this chip is
referred to as the Embedded Management Processor firmware (EMP
firmware).
Activating the new firmware image currently requires that the system be
rebooted. This is not ideal as rebooting the system can cause unwanted
downtime.
In practical terms, activating the firmware does not always require a
full system reboot. In many cases it is possible to activate the EMP
firmware immediately. There are a couple of different scenarios to
cover.
* The EMP firmware itself can be reloaded by issuing a special update
to the device called an Embedded Management Processor reset (EMP
reset). This reset causes the device to reset and reload the EMP
firmware.
* PCI configuration changes are only reloaded after a cold PCIe reset.
Unfortunately there is no generic way to trigger this for a PCIe
device without a system reboot.
When performing a flash update, firmware is capable of responding with
some information about the specific update requirements.
The driver updates the flash by programming a secondary inactive bank
with the contents of the new image, and then issuing a command to
request to switch the active bank starting from the next load.
The response to the final command for updating the inactive NVM flash
bank includes an indication of the minimum reset required to fully
update the device. This can be one of the following:
* A full power on is required
* A cold PCIe reset is required
* An EMP reset is required
The response to the command to switch flash banks includes an indication
of whether or not the firmware will allow an EMP reset request.
For most updates, an EMP reset is sufficient to load the new EMP
firmware without issues. In some cases, this reset is not sufficient
because the PCI configuration space has changed. When this could cause
incompatibility with the new EMP image, the firmware is capable of
rejecting the EMP reset request.
Add logic to ice_fw_update.c to handle the response data flash update
AdminQ commands.
For the reset level, issue a devlink status notification informing the
user of how to complete the update with a simple suggestion like
"Activate new firmware by rebooting the system".
Cache the status of whether or not firmware will restrict the EMP reset
for use in implementing devlink reload.
Implement support for devlink reload with the "fw_activate" flag. This
allows user space to request the firmware be activated immediately.
For the .reload_down handler, we will issue a request for the EMP reset
using the appropriate firmware AdminQ command. If we know that the
firmware will not allow an EMP reset, simply exit with a suitable
netlink extended ACK message indicating that the EMP reset is not
available.
For the .reload_up handler, simply wait until the driver has finished
resetting. Logic to handle processing of an EMP reset already exists in
the driver as part of its reset and rebuild flows.
Implement support for the devlink reload interface with the
"fw_activate" action. This allows userspace to request activation of
firmware without a reboot.
Note that support for indicating the required reset and EMP reset
restriction is not supported on old versions of firmware. The driver can
determine if the two features are supported by checking the device
capabilities report. I confirmed support has existed since at least
version 5.5.2 as reported by the 'fw.mgmt' version. Support to issue the
EMP reset request has existed in all version of the EMP firmware for the
ice hardware.
Check the device capabilities report to determine whether or not the
indications are reported by the running firmware. If the reset
requirement indication is not supported, always assume a full power on
is necessary. If the reset restriction capability is not supported,
always assume the EMP reset is available.
Users can verify if the EMP reset has activated the firmware by using
the devlink info report to check that the 'running' firmware version has
updated. For example a user might do the following:
# Check current version
$ devlink dev info
# Update the device
$ devlink dev flash pci/0000:af:00.0 file firmware.bin
# Confirm stored version updated
$ devlink dev info
# Reload to activate new firmware
$ devlink dev reload pci/0000:af:00.0 action fw_activate
# Confirm running version updated
$ devlink dev info
Finally, this change does *not* implement basic driver-only reload
support. I did look into trying to do this. However, it requires
significant refactor of how the ice driver probes and loads everything.
The ice driver probe and allocation flows were not designed with such
a reload in mind. Refactoring the flow to support this is beyond the
scope of this change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
During probe and device reset, the ice driver reads some data from the
NVM image as part of ice_init_nvm. Part of this data includes a section
of the Option ROM which contains version information.
The function ice_get_orom_civd_data is used to locate the '$CIV' data
section of the Option ROM.
Timing of ice_probe and ice_rebuild indicate that the
ice_get_orom_civd_data function takes about 10 seconds to finish
executing.
The function locates the section by scanning the Option ROM every 512
bytes. This requires a significant number of NVM read accesses, since
the Option ROM bank is 500KB. In the worst case it would take about 1000
reads. Worse, all PFs serialize this operation during reload because of
acquiring the NVM semaphore.
The CIVD section is located at the end of the Option ROM image data.
Unfortunately, the driver has no easy method to determine the offset
manually. Practical experiments have shown that the data could be at
a variety of locations, so simply reversing the scanning order is not
sufficient to reduce the overall read time.
Instead, copy the entire contents of the Option ROM into memory. This
allows reading the data using 4Kb pages instead of 512 bytes at a time.
This reduces the total number of firmware commands by a factor of 8. In
addition, reading the whole section together at once allows better
indication to firmware of when we're "done".
Re-write ice_get_orom_civd_data to allocate virtual memory to store the
Option ROM data. Copy the entire OptionROM contents at once using
ice_read_flash_module. Finally, use this memory copy to scan for the
'$CIV' section.
This change significantly reduces the time to read the Option ROM CIVD
section from ~10 seconds down to ~1 second. This has a significant
impact on the total time to complete a driver rebuild or probe.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_devlink_flash_update function performs a few upfront checks and
then calls ice_flash_pldm_image.
Most if these checks make more sense in the context of code within
ice_flash_pldm_image. Merge ice_devlink_flash_update and
ice_flash_pldm_image into one function, placing it in ice_fw_update.c
Since this is still the entry point for devlink, call the function
ice_devlink_flash_update instead of ice_flash_pldm_image. This leaves a
single function which handles the devlink parameters and then initiates
a PLDM update.
With this change, the ice_devlink_flash_update function in
ice_fw_update.c becomes the main entry point for flash update. It
elimintes some unnecessary boiler plate code between the two previous
functions. The ultimate motivation for this is that it eases supporting
a dry run with the PLDM library in a future change.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_devlink_flash_update function performs a few checks and then
calls ice_flash_pldm_image. One of these checks is to call
ice_check_for_pending_update. This function checks if the device has
a pending update, and cancels it if so. This is necessary to allow
a new flash update to proceed.
We want to refactor the ice code to eliminate ice_devlink_flash_update,
moving its checks into ice_flash_pldm_image.
To do this, ice_check_for_pending_update will become static, and only
called by ice_flash_pldm_image. To make this change easier to review,
first just move the function up within the ice_fw_update.c file.
While at it, note that the function has a misleading name. Its primary
action is to cancel a pending update. Using the verb "check" does not
imply this. Rename it to ice_cancel_pending_update.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
We have a region for reading the contents of the NVM flash as
a snapshot. This region does not allow reading the Shadow RAM, as it
always passes the FLASH_ONLY bit to the low level firmware interface.
Add a separate shadow-ram region which will allow snapshot of the
current contents of the Shadow RAM. This data is built from the NVM
contents but is distinct as the device builds up the Shadow RAM during
initialization, so being able to snapshot its contents can be useful
when attempting to debug flash related issues.
Fix the comment description of the nvm-flash region which incorrectly
stated that it filled the shadow-ram region, and add a comment
explaining that the nvm-flash region does not actually read the Shadow
RAM.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
A new warning in clang points out two instances where boolean
expressions are being used with a bitwise OR instead of logical OR:
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:72:9: note: cast one or both operands to int to silence this warning
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: warning: use of bitwise '|' with boolean operands [-Wbitwise-instead-of-logical]
reg = tegra_fuse_read_spare(i) |
^~~~~~~~~~~~~~~~~~~~~~~~~~
||
drivers/soc/tegra/fuse/speedo-tegra20.c:87:9: note: cast one or both operands to int to silence this warning
2 warnings generated.
The motivation for the warning is that logical operations short circuit
while bitwise operations do not.
In this instance, tegra_fuse_read_spare() is not semantically returning
a boolean, it is returning a bit value. Use u32 for its return type so
that it can be used with either bitwise or boolean operators without any
warnings.
Fixes: 25cd5a391478 ("ARM: tegra: Add speedo-based process identification")
Link: https://github.com/ClangBuiltLinux/linux/issues/1488
Suggested-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
Arnd Bergmann
Haimin Zhang
Ioana Ciornei
Rob Clark
Dmitry Baryshkov
Dan Carpenter
Mathias Nyman
Yang Yingliang
Amelie Delaunay
Xu Yang
Pawel Laszczak
Jimmy Wang
Nehal Bakulchandra Shah
Frank Rowand
Jim Quinlan
Hans de Goede
Christophe JAILLET
Mark Brown
Ji-Ze Hong (Peter Hong)
Tetsuo Handa
Yifeng Li
Cyril Novikov
Mike Snitzer
Robert Schlabbach
Sasha Neftin
Letu Ren
Karen Sornek
Linus Torvalds
Dmitry Osipenko
Greg Kroah-Hartman
Jesse Brandeburg
Jacob Keller
Nathan Chancellor