| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
The switch supports fast aging by flushing any rule in the ARL
table for a specific port.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We are currently missing 2 additionals MIB counter present in QCA833x
switch.
QC832x switch have 39 MIB counter and QCA833X have 41 MIB counter.
Add the additional MIB counter and rework the MIB function to print the
correct supported counter from the match_data struct.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert any qca8k set/clear/pool to regmap helper and add
missing config to regmap_config struct.
Read/write/rmw operation are reworked to use the regmap helper
internally to keep the delta of this patch low. These additional
function will then be dropped when the code split will be proposed.
Ipq40xx SoC have the internal switch based on the qca8k regmap but use
mmio for read/write/rmw operation instead of mdio.
In preparation for the support of this internal switch, convert the
driver to regmap API to later split the driver to common and specific
code. The overhead introduced by the use of regamp API is marginal as the
internal mdio will bypass it by using its direct access and regmap will be
used only by configuration functions or fdb access.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for regmap conversion, move regmap init in the probe
function and make it mandatory as any read/write/rmw operation will be
converted to regmap API.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mutex is already init in sw_probe. Remove the extra init in qca8k_setup.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert and try to standardize bit fields using
GENMASK/FIELD_PREP/FIELD_GET macros. Rework some logic to support the
standard macro and tidy things up. No functional change intended.
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The very next check for port 0 and 6 already makes sure we don't go out
of bounds with the ports_config delay table.
Remove the redundant check.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Having the parent of the audio_root_clk set to ipg_root
in the clk-imx8mp.c, there is a hang happening when the
audiomix IP regs are accessed. Switch parent to audio_ahb.
And we could also refer to the section "5.1.4 System Clocks" of the
IMX8MPRM.pdf, the parent clk of CCGR101 (Audiomix) is the
AUDIO_AHB_CLK_ROOT.
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20211109125657.63485-2-hui.wang@canonical.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally writing across neighboring fields.
Replace the existing empty member position markers "headers_start" and
"headers_end" with a struct_group(). This will allow memcpy() and sizeof()
to more easily reason about sizes, and improve readability.
"pahole" shows no size nor member offset changes to struct sk_buff.
"objdump -d" shows no object code changes (outside of WARNs affected by
source line number changes).
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jason A. Donenfeld <Jason@zx2c4.com> # drivers/net/wireguard/*
Link: https://lore.kernel.org/lkml/20210728035006.GD35706@embeddedor
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The change to eth_hw_addr_set() caused gcc to correctly spot a
bug that was introduced in an earlier incorrect fix:
In file included from include/linux/etherdevice.h:21,
from drivers/net/ethernet/ni/nixge.c:7:
In function '__dev_addr_set',
inlined from 'eth_hw_addr_set' at include/linux/etherdevice.h:319:2,
inlined from 'nixge_probe' at drivers/net/ethernet/ni/nixge.c:1286:3:
include/linux/netdevice.h:4648:9: error: 'memcpy' reading 6 bytes from a region of size 0 [-Werror=stringop-overread]
4648 | memcpy(dev->dev_addr, addr, len);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
As nixge_get_nvmem_address() can return either NULL or an error
pointer, the NULL check is wrong, and we can end up reading from
ERR_PTR(-EOPNOTSUPP), which gcc knows to contain zero readable
bytes.
Make the function always return an error pointer again but fix
the check to match that.
Fixes: f3956ebb3bf0 ("ethernet: use eth_hw_addr_set() instead of ether_addr_copy()")
Fixes: abcd3d6fc640 ("net: nixge: Fix error path for obtaining mac address")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Epoch Subsystem (EPSS) L3 interconnect provider support on
SC7280 SoCs.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1634812857-10676-3-git-send-email-okukatla@codeaurora.org
Signed-off-by: Georgi Djakov <djakov@kernel.org>
|
|
In HE monitor capture, HAL_TLV_STATUS_PPDU_DONE is received
on processing multiple skb. Do not clear the ppdu_info
till the HAL_TLV_STATUS_PPDU_DONE is received.
This fixes below warning and packet drops in monitor mode.
"Rate marked as an HE rate but data is invalid: MCS: 6, NSS: 0"
WARNING: at
PC is at ieee80211_rx_napi+0x624/0x840 [mac80211]
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01693-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1637249433-10316-1-git-send-email-akolli@codeaurora.org
|
|
This is to read variant from SMBIOS such as read from DT, the variant
string will be used to one part of string which used to search board
data from board-2.bin.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118100033.8384-1-quic_wgong@quicinc.com
|
|
The ath11k driver currently sends vdev down to the firmware before
updating the channel context, which is followed by a vdev restart
command.
Sending vdev down is not required before sending a vdev restart,
because the firmware internally does vdev down when ath11k sends
a vdev restart command.
Firmware will happen crash while channel switch without this change.
Hence skip the vdev down command sending when updating the channel
context and then fix the firmware crash issue.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095901.8271-1-quic_wgong@quicinc.com
|
|
The pdev id is set to 0 for single pdev configured hardware, the real
pdev id is not 0 in firmware, for example, its pdev id is 1 for 5G/6G
phy and 2 for 2G band phy. For HTT_H2T_MSG_TYPE_EXT_STATS_CFG message,
firmware parse the pdev_mask to its pdev id, ath11k set it to 0 for
single pdev, it is not correct, need set it with the real pdev id of
firmware.
Save the real pdev id report by firmware and set it correctly.
Below commands run success with this patch:
cat /sys/kernel/debug/ieee80211/phy0/ath11k/htt_stats
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wls1/stations/00\:03\:7f\:75\:59\:85/htt_peer_stats
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095700.8149-1-quic_wgong@quicinc.com
|
|
When connected to 6G mode AP, it does not have VHT/HT capabilities,
so the NSS is not set, then it is 1 by default.
This patch is to calculate the NSS with supported HE-MCS and NSS set
of HE capabilities.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01280-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095453.8030-1-quic_wgong@quicinc.com
|
|
'send_section_map' is a bitmap. So use 'bitmap_zalloc()' to simplify code,
improve the semantic and avoid some open-coded arithmetic in allocator
arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
While at it, change an '== NULL' test into a '!'.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some firmware versions for WCN6855 report the default regdomain with
alpha code "na" by default when load as a world wide regdomain, ath11k
should treat it as a world wide alpha code.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118094848.7776-1-quic_wgong@quicinc.com
|
|
Function axspi_read_status calls:
ret = spi_write_then_read(ax_spi->spi, ax_spi->cmd_buf, 1,
(u8 *)&status, 3);
status is a pointer to a struct spi_status, which is 3-byte wide:
struct spi_status {
u16 isr;
u8 status;
};
But &status is the pointer to this pointer, and spi_write_then_read does
not dereference this parameter:
int spi_write_then_read(struct spi_device *spi,
const void *txbuf, unsigned n_tx,
void *rxbuf, unsigned n_rx)
Therefore axspi_read_status currently receive a SPI response in the
pointer status, which overwrites 24 bits of the pointer.
Thankfully, on Little-Endian systems, the pointer is only used in
le16_to_cpus(&status->isr);
... which is a no-operation. So there, the overwritten pointer is not
dereferenced. Nevertheless on Big-Endian systems, this can lead to
dereferencing pointers after their 24 most significant bits were
overwritten. And in all systems this leads to possible use of
uninitialized value in functions calling spi_write_then_read which
expect status to be initialized when the function returns.
Moreover function axspi_read_status (and macro AX_READ_STATUS) do not
seem to be used anywhere. So currently this seems to be dead code. Fix
the issue anyway so that future code works properly when using function
axspi_read_status.
Fixes: a97c69ba4f30 ("net: ax88796c: ASIX AX88796C SPI Ethernet Adapter Driver")
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: Łukasz Stelmach <l.stelmach@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'cid_map' is a bitmap. So use 'bitmap_zalloc()' to simplify code,
improve the semantic and avoid some open-coded arithmetic in allocator
arguments.
Also change the corresponding 'kfree()' into 'bitmap_free()' to keep
consistency.
Also change some 'memset()' into 'bitmap_zero()' to keep consistency. This
is also much less verbose.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, when user space emits SIOCSHWTSTAMP ioctl calls such as
enabling/disabling timestamping or changing filter settings, the driver
reads the current CLOCK_REALTIME value and programming this into the
NIC's hardware clock. This might be necessary during system
initialization, but at runtime, when the PTP clock has already been
synchronized to a grandmaster, a reset of the timestamp settings might
result in a clock jump. Furthermore, if the clock is also controlled by
phc2sys in automatic mode (where the UTC offset is queried from ptp4l),
that UTC-to-TAI offset (currently 37 seconds in 2021) would be
temporarily reset to 0, and it would take a long time for phc2sys to
readjust so that CLOCK_REALTIME and the PHC are apart by 37 seconds
again.
To address the issue, we introduce a new function called
stmmac_init_tstamp_counter(), which gets called during ndo_open().
It contains the code snippet moved from stmmac_hwtstamp_set() that
manages the time synchronization. Besides, the sub second increment
configuration is also moved here since the related values are hardware
dependent and runtime invariant.
Furthermore, the hardware clock must be kept running even when no time
stamping mode is selected in order to retain the synchronized time base.
That way, timestamping can be enabled again at any time only with the
need to compensate the clock's natural drifting.
As a side effect, this patch fixes the issue that ptp_clock_info::enable
can be called before SIOCSHWTSTAMP and the driver (which looks at
priv->systime_flags) was not prepared to handle that ordering.
Fixes: 92ba6888510c ("stmmac: add the support for PTP hw clock driver")
Reported-by: Michael Olbrich <m.olbrich@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are three boolean variable which were not initialized and later
being used in the code.
Signed-off-by: Yacov Simhony <ysimhony@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function returns a bool type so returning -EBUSY is equivalent to
returning true. It should return false instead.
Fixes: 7ae034590cea ("drm/i915/ttm: add tt shmem backend")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211122061438.GA2492@kili
|
|
Let's enable runtime pm autosuspend by default everywhere.
So, we can allow D3hot and bigger power savings on idle scenarios.
But at this time let's not touch the autosuspend_delay time,
what caused some regression on our previous attempt.
Also, the latest identified issue on GuC PM has been fixed by
commit 1a52faed3131 ("drm/i915/guc: Take GT PM ref when deregistering
context")
v1: Enable runtime pm autosuspend by default for Gen12
and later versions.
v2: Enable runtime pm autosuspend by default for all
platforms(Syrjala Ville)
v3: Change commit message(Nikula Jani)
Signed-off-by: Tilak Tangudu <tilak.tangudu@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211116155238.3226516-1-tilak.tangudu@intel.com
|
|
pcmcia_get_mac_from_cis is only called from networking and
recent changes made it call dev_addr_mod() which is itself
only defined if NET.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to const dev_addr changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When attempting to use sys_pll1_80m as the parent for clko1, the
system hangs. This is due to the fact that the source select
for sys_pll1_80m was incorrectly pointing to m7_alt_pll_clk, which
doesn't yet exist.
According to Rev 3 of the TRM, The imx8mn_clko1_sels also incorrectly
references an osc_27m which does not exist, nor does an entry for
source select bits 010b. Fix both by inserting a dummy clock into
the missing space in the table and renaming the incorrectly name clock
with dummy.
Fixes: 96d6392b54db ("clk: imx: Add support for i.MX8MN clock driver")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20211117133202.775633-1-aford173@gmail.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
do_div() does a 64-by-32 division. Here the divisor is an unsigned long
which on some platforms is 64 bit wide. So use div64_ul instead of do_div
to avoid a possible truncation.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Changcheng Deng <deng.changcheng@zte.com.cn>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20211118080634.165275-1-deng.changcheng@zte.com.cn
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
This patch brings in support for device trace collection.
It implements relayfs interface for pushing device trace
from kernel space to user space.
Driver gets the debugfs base directory associated to WWAN
Device and creates trace_control and trace debugfs for
device tracing. Both trace_control & trace debugfs are
created under /sys/kernel/debug/wwan/wwan0/.
In order to collect device trace on trace0 interface, user
need to write 1 to trace_ctl interface.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch set brings in a common debugfs base directory
i.e. /sys/kernel/debugfs/wwan/ in WWAN Subsystem for a
WWAN device instance. So that it avoids driver polluting
debugfs root with unrelated directories & possible name
collusion.
Having a common debugfs base directory for WWAN drivers
eases user to match control devices with debugfs entries.
WWAN Subsystem creates dentry (/sys/kernel/debugfs/wwan)
on module load & removes dentry on module unload.
When driver registers a new wwan device, dentry (wwanX)
is created for WWAN device instance & on driver unregister
dentry is removed.
New API is introduced to return the wwan device instance
dentry so that driver can create debugfs entries under it.
Signed-off-by: M Chetan Kumar <m.chetan.kumar@linux.intel.com>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Argument of a helper is missing a const.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: adeef3e32146 ("net: constify netdev->dev_addr")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support of XDP for the MANA driver.
Supported XDP actions:
XDP_PASS, XDP_TX, XDP_DROP, XDP_ABORTED
XDP actions not yet supported:
XDP_REDIRECT
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSN endpoint Ethernet MAC is a FPGA based network device for
real-time communication.
It is integrated as Ethernet controller with ethtool and PTP support.
For real-time communcation TC_SETUP_QDISC_TAPRIO is supported.
Signed-off-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4904b6ea1f9db ("net: phy: phylink: Use PHY device interface if
N/A") introduced handling for the phy interface mode where this is not
known at phylink creation time. This was never added to the OF/fwnode
paths, but is necessary when the phy is present in DT, but the phy-mode
is not specified.
Add this handling.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some devices expose memory-mapped c22-compliant PHYs. Because these
devices do not have an MDIO bus, we cannot use the existing helpers.
Refactor the existing helpers to allow supplying the values for c22
registers directly, instead of using MDIO to access them. Only get_state
and set_advertisement are converted, since they contain the most complex
logic. Because set_advertisement is never actually used outside
phylink_mii_c22_pcs_config, move the MDIO-writing part into that
function. Because some modes do not need the advertisement register set
at all, we use -EINVAL for this purpose.
Additionally, a new function phylink_pcs_enable_an is provided to
determine whether to enable autonegotiation.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 79f960e29cfc ("platform/x86: thinkpad_acpi: Convert platform driver
to use dev_groups") accidentally modified tpacpi_kbdlang_init() causing it
to return -ENODEV instead of 0 on machines without kbdlang support
(which are most of them).
ibm_init() sees this -ENODEV as an error causing the entire module to not
load, not good.
Note that technically tpacpi_kbdlang_init() was already buggy before, it
should have returned 1 instead of 0 if the feature is not present.
Rather then fixing tpacpi_kbdlang_init() though, IMHO it is bettter to
just make ibm_init() treat -ENODEV as 1 to fix the issue; and then in
a followup commit also change all the existing "return 1"s from
ibm_init_struct.init() callbacks to "return -ENODEV" as -ENODEV clearly
states what it going on where as a magic return of "1" requires a deep
dive into the code to figure out what is going on.
This will also allow removing some extra ifs to translate -ENODEV to
return 1 in a couple of init() callbacks.
Fixes: 79f960e29cfc ("platform/x86: thinkpad_acpi: Convert platform driver to use dev_groups")
Cc: Len Baker <len.baker@gmx.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211121191129.256713-2-hdegoede@redhat.com
|
|
Creating the tlmi_pwd_setting structs can only fail with -ENOMEM, set
ret to this once and simplify the error handling a bit.
Tested-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211118114150.271274-2-hdegoede@redhat.com
|
|
All callers of tlmi_create_auth() also call
kobject_init(&pwd_setting->kobj, &tlmi_pwd_setting_ktype) on the returned
tlmi_pwd_setting struct. Move this into tlmi_create_auth().
Tested-by: Mark Pearson <markpearson@lenovo.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211118114150.271274-1-hdegoede@redhat.com
|
|
dev->gso_max_segs is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add netif_set_gso_max_segs() helper.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_segs()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev->gso_max_size is written under RTNL protection, or when the device is
not yet visible, but is read locklessly.
Add the READ_ONCE()/WRITE_ONCE() pairs, and use netif_set_gso_max_size()
where we can to better document what is going on.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use nn->tlv_caps.me_freq_mhz instead of nn->me_freq_mhz to check whether
rx-usecs/tx-usecs is valid.
This is because nn->tlv_caps.me_freq_mhz represents the clock_freq (MHz) of
the flow processing cores (FPC) on the NIC. While nn->me_freq_mhz is not
be set.
Fixes: ce991ab6662a ("nfp: read ME frequency from vNIC ctrl memory")
Signed-off-by: Diana Wang <na.wang@corigine.com>
Signed-off-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clock driver is registered as platform devices and
it is possible to reloading the driver at runtime.
But actually the clocks should never be removed to make system work,
attempting to bind again would result in a crash, because almost all
devices depends on clock to function well.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20211022131513.17381-1-peng.fan@oss.nxp.com
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
qca8k has a global MTU, so its tracking the MTU per port to make sure
that the largest MTU gets applied.
Since it uses the frame size instead of MTU the driver MTU change function
will then add the size of Ethernet header and checksum on top of MTU.
The driver currently populates the per port MTU size as Ethernet frame
length + checksum which equals 1518.
The issue is that then MTU change function will go through all of the
ports, find the largest MTU and apply the Ethernet header + checksum on
top of it again, so for a desired MTU of 1500 you will end up with 1536.
This is obviously incorrect, so to correct it populate the per port struct
MTU with just the MTU and not include the Ethernet header + checksum size
as those will be added by the MTU change function.
Fixes: f58d2598cf70 ("net: dsa: qca8k: implement the port MTU callbacks")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With SGMII phy the internal delay is always applied to the PAD0 config.
This is caused by the falling edge configuration that hardcode the reg
to PAD0 (as the falling edge bits are present only in PAD0 reg)
Move the delay configuration before the reg overwrite to correctly apply
the delay.
Fixes: cef08115846e ("net: dsa: qca8k: set internal delay also for sgmii")
Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The way to set tx spare buf via module parameter is not such
convenient as the way to set it via ethtool.
So,remove the way to set tx spare buf via module parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rx buf len is for rx BD buffer size, support setting it via ethtool -G
parameter and getting it via ethtool -g parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx copybreak buf size is used for tx copybreak feature, the feature is
used for small size packet or frag. It adds a queue based tx shared
bounce buffer to memcpy the small packet when the len of xmitted skb is
below tx_copybreak(value to distinguish small size and normal size),
and reduce the overhead of dma map and unmap when IOMMU is on.
Support setting it via ethtool --set-tunable parameter and getting
it via ethtool --get-tunable parameter.
Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas needs the dma_resv_for_each_fence API for i915/ttm async migration
work.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
|
|
With VT-d disabled on Intel platform, ath11k gets only one MSI
vector. In that case, ath11k does not free IRQ when doing suspend,
hence the kernel has to migrate it to CPU0 (if it was affine to
other CPUs) and allocates a new MSI vector. However, ath11k has
no chance to reconfig it to HW srngs during this phase, thus
ath11k fails to resume.
This issue can be fixed by setting IRQ affinity to CPU0 before
request_irq is called. With such affinity, migration will not
happen and thus the vector keeps unchanged during suspend/resume.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211026041732.5323-1-bqiang@codeaurora.org
|
Ansuel Smith
Hui Wang
Kees Cook
Arnd Bergmann
Odelu Kukatla
Anilkumar Kolli
Wen Gong
Christophe JAILLET
Nicolas Iooss
Holger Assmann
Yacov Simhony
Dan Carpenter
Tilak Tangudu
Jakub Kicinski
David S. Miller
Adam Ford
Changcheng Deng
M Chetan Kumar
Haiyang Zhang
Gerhard Engleder
Russell King (Oracle)
Sean Anderson
Hans de Goede
Eric Dumazet
Diana Wang
Peng Fan
Robert Marko
Hao Chen
Tvrtko Ursulin
Baochen Qiang