| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
USB control-message timeouts are specified in milliseconds and should
specifically not vary with CONFIG_HZ.
Fixes: 487358627825 ("Input: iforce - use DMA-safe buffer when getting IDs from USB")
Signed-off-by: Johan Hovold <johan@kernel.org>
Cc: stable@vger.kernel.org # 5.3
Link: https://lore.kernel.org/r/20211025115501.5190-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
To make the code easier to read use macros for the bit masks.
Signed-off-by: Alistair Francis <alistair@alistair23.me>
Link: https://lore.kernel.org/r/20211009113707.17568-2-alistair@alistair23.me
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Modern devices may redraw display at 60 Hz, make sure we have one input
sample per one frame. Reduce sample period to 15ms, so we would get up
to 66.6 samples per second, although realistically with all the jitter
and extra scheduling wiggle room, we would end up just above 60 samples
per second. This should be a good compromise between sampling too often
and sampling too seldom.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108114145.84118-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Currently the ili210x driver implements a threaded interrupt handler which
starts upon edge on the interrupt line, and then polls the touch controller
for samples. Every time a sample is obtained from the controller, the thread
function checks whether further polling is required, and if so, waits fixed
amount of time before polling for next sample.
The delay between consecutive samples can thus vary greatly, because the
I2C transfer required to retrieve the sample from the controller takes
different amount of time on different platforms. Furthermore, different
models of the touch controllers supported by this driver require different
delays during retrieval of samples too.
Instead of waiting fixed amount of time before polling for next sample,
determine how much time passed since the beginning of sampling cycle and
then wait only the remaining amount of time within the sampling cycle.
This makes the driver deliver samples with equal spacing between them.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005216.480525-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The ili251x touch controller needs 5ms delay between sending I2C device
address and register address, and, writing or reading register data.
According to downstream ili251x example code, this 5ms delay is not
required when reading touch samples out of the controller. Implement
such a special case.
Signed-off-by: Marek Vasut <marex@denx.de>
Link: https://lore.kernel.org/r/20211108005259.480545-1-marex@denx.de
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Some firmwares occasionally report bogus data from trackpoint, with X or Y
displacement being too large (outside of [-127, 127] range). Let's drop such
packets so that we do not generate jumps.
Signed-off-by: Phoenix Huang <phoenix@emc.com.tw>
Tested-by: Yufei Du <yufeidu@cs.unc.edu>
Link: https://lore.kernel.org/r/20210729010940.5752-1-phoenix@emc.com.tw
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
There is a spelling mistake in a dev_info message. Fix it.
Signed-off-by: Colin Ian King <colin.i.king@gmail.com>
Reviewed-by: Dexuan Cui <decui@microsoft.com>
Link: https://lore.kernel.org/r/20211108201817.43121-1-colin.i.king@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the amt module is being removed, it calls flush_delayed_work() to exit
source_gc_wq. But it wouldn't be exited properly because the
amt_source_gc_work(), which is the callback function of source_gc_wq
internally calls mod_delayed_work() again.
So, amt_source_gc_work() would be called after the amt module is removed.
Therefore kernel panic would occur.
In order to avoid it, cancel_delayed_work() should be used instead of
flush_delayed_work().
Test commands:
modprobe amt
modprobe -rv amt
Splat looks like:
BUG: unable to handle page fault for address: fffffbfff80f50db
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 1237ee067 P4D 1237ee067 PUD 1237b2067 PMD 100c11067 PTE 0
Oops: 0000 [#1] PREEMPT SMP DEBUG_PAGEALLOC KASAN PTI
CPU: 1 PID: 0 Comm: swapper/1 Not tainted 5.15.0+ #27
5a0ebebc29fe5c40c68bea90197606c3a832b09f
RIP: 0010:run_timer_softirq+0x221/0xfc0
Code: 00 00 4c 89 e1 4c 8b 30 48 c1 e9 03 80 3c 29 00 0f 85 ed 0b 00 00
4d 89 34 24 4d 85 f6 74 19 49 8d 7e 08 48 89 f9 48 c1 e9 03 <80> 3c 29 00
0f 85 fa 0b 00 00 4d 89 66 08 83 04 24 01 49 89 d4 48
RSP: 0018:ffff888119009e50 EFLAGS: 00010806
RAX: ffff8881191f8a80 RBX: 00000000007ffe2a RCX: 1ffffffff80f50db
RDX: ffff888119009ed0 RSI: 0000000000000008 RDI: ffffffffc07a86d8
RBP: dffffc0000000000 R08: ffff8881191f8280 R09: ffffed102323f061
R10: ffff8881191f8307 R11: ffffed102323f060 R12: ffff888119009ec8
R13: 00000000000000c0 R14: ffffffffc07a86d0 R15: ffff8881191f82e8
FS: 0000000000000000(0000) GS:ffff888119000000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: fffffbfff80f50db CR3: 00000001062dc002 CR4: 00000000003706e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
? add_timer+0x650/0x650
? kvm_clock_read+0x14/0x30
? ktime_get+0xb9/0x180
? rcu_read_lock_held_common+0xe/0xa0
? rcu_read_lock_sched_held+0x56/0xc0
? rcu_read_lock_bh_held+0xa0/0xa0
? hrtimer_interrupt+0x271/0x790
__do_softirq+0x1d0/0x88f
irq_exit_rcu+0xe7/0x120
sysvec_apic_timer_interrupt+0x8a/0xb0
</IRQ>
<TASK>
[ ... ]
Fixes: bc54e49c140b ("amt: add multicast(IGMP) report message handler")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Link: https://lore.kernel.org/r/20211108145340.17208-1-ap420073@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Couple Reverts, build fix, couple virtualization fixes,
blank screen and other display rates fixes, and more.
Four patches targeting stable in here.
Display Fixes:
- DP rates related fixes (Imre, Jani)
- A Revert on disaling dual eDP that was causing state readout problems (Jani)
- put the cdclk vtables in const data (Jani)
- Fix DVO port type for moder platforms (Ville)
- Fix blankscreen by turning DP++ TMDS output buffers on encoder->shutdown (Ville)
- CCS FBs related fixes (Imre)
GT fixes:
- Fix recursive lock in GuC submission (Matt Brost)
- Revert guc_id from i915_request tracepoint (Joonas)
- Build fix around dmabuf (Matt Auld)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YYsBif3HMi8GjLoU@intel.com
|
|
A refcounting fix for outstanding fence callbacks.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105074318.oy6rwjr5wcw6qpjj@gilmour
|
|
Model 88E6191X only supports >1G speeds on port 10. Port 0 and 9 are
only 1G.
Fixes: de776d0d316f ("net: dsa: mv88e6xxx: add support for mv88e6393x family")
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20211104171747.10509-1-kabel@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver has its own sysfs file to adjust the clock. Fortunately, it is
already in pbb, however, the sign it expects is the opposite of what the
RTC core does (which actually aligns with the RTC).
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-12-alexandre.belloni@bootlin.com
|
|
Remove open coded sysfs registration by using rtc_add_group.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-11-alexandre.belloni@bootlin.com
|
|
Clear RTC_FEATURE_ALARM to signal alarms are not supported to the core
instead of checking client->irq.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-10-alexandre.belloni@bootlin.com
|
|
Set the RTC range, it is a classic BCD RTC, with 00 being a leap
year. Let the core handle range checking.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-9-alexandre.belloni@bootlin.com
|
|
Tell the RTC core UIE are not supported because the resolution of the alarm
is a minute.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-8-alexandre.belloni@bootlin.com
|
|
Switch to devm_rtc_allocate_device/devm_rtc_register_device, this allows
for further improvement of the driver.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-7-alexandre.belloni@bootlin.com
|
|
Tell the RTC core UIE are not supported because the resolution of the alarm
is a minute.
Note that this is in fact also fixing how the resolution is reported as the
previous test was simply ensuring the alarm was more than a minute in the
future while the register has a minute resolution.
This would be ok if the alarm was a countdown but ab8500_rtc_read_alarm
suggests otherwise and the AB8500 datasheet states that the RTC
documentation is not public.
Finally, the comment is wrong and what makes the UIE emulation work is
uie_unsupported being set.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20211107225458.111068-6-alexandre.belloni@bootlin.com
|
|
The RTC actually supports UIE when an interrupt is available.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-5-alexandre.belloni@bootlin.com
|
|
Switch from uie_unsupported to RTC_FEATURE_UPDATE_INTERRUPT
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-4-alexandre.belloni@bootlin.com
|
|
Let the RTC core know the resolution of the alarm is a minute.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-3-alexandre.belloni@bootlin.com
|
|
Tell the RTC core UIE are not supported because the resolution of the alarm
is a minute.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-2-alexandre.belloni@bootlin.com
|
|
Handle alarms with a minute resolution in the core. Until now drivers have
been open coding the seconds part removal and have been doing that wrongly.
Most of them are rounding up which means the allow the system to miss
deadlines. So, round down and let __rtc_set_alarm return immediately if the
time has already passed.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225458.111068-1-alexandre.belloni@bootlin.com
|
|
cppcheck warnings: (new ones prefixed by >>)
>> drivers/rtc/rtc-pcf85063.c:292:40: warning: Clarify calculation precedence for '&' and '?'. [clarifyCalculation]
status = status & PCF85063_REG_SC_OS ? RTC_VL_DATA_INVALID : 0;
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211107225349.110707-1-alexandre.belloni@bootlin.com
|
|
ctrl is set from read_regs(..FLAG, 2, ctrl), so ctrl[0] is FLAG
and ctrl[1] is the CTRL register.
Use ctrl[0] to write back to the FLAG register as appropriate.
Signed-off-by: Dominique Martinet <dominique.martinet@atmark-techno.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20211101013400.325855-1-dominique.martinet@atmark-techno.com
|
|
When i915 receives a context reset notification from GuC, it triggers
an error capture before resetting any outstanding requsts of that
context. Unfortunately, the error capture is not a time bound
operation. In certain situations it can take a long time, particularly
when multiple large LMEM buffers must be read back and eoncoded. If
this delay is longer than other timeouts (heartbeat, test recovery,
etc.) then a full GT reset can be triggered in the middle.
That can result in the context being reset by GuC actually being
destroyed before the error capture completes and the GuC submission
code resumes. Thus, the GuC side can start dereferencing stale
pointers and Bad Things ensue.
So add a refcount get of the context during the entire reset
operation. That way, the context can't be destroyed part way through
no matter what other resets or user interactions occur.
v2:
(Matthew Brost)
- Update patch to work with async error capture
v3:
(Matthew Brost)
- Drop async capture support as that hasn't landed yet
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Matthew Brost <matthew.brost@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211108164054.23588-1-matthew.brost@intel.com
|
|
The "ret" variable is checked on the previous line so we know it's
zero. No need to check again.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211109114850.GB16587@kili
|
|
Currently we're only calling intel_update_active_dpll() for the
bigjoiner master pipe but not for the slave. With TC ports this
leads to the two pipes end up trying to use different PLLs
(TC vs. TBT). What's worse we're enabling the PLL that didn't get
intel_update_active_dpll() called on it at the spot where we
need the clocks turned on. So we turn on the wrong PLL and the
DDI is now trying to source its clock from the other PLL which is
still disabled. Naturally that doesn't end so well and the DDI
fails to start up.
The state checker also gets a bit unhappy (which is a good thing)
when it notices that one of the pipes was using the wrong PLL.
Let's fix this by remembering to call intel_update_active_dpll()
for both pipes. That should get the correct PLL turned on when
we need it, and the state checker should also be happy.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4434
Fixes: e12d6218fda2 ("drm/i915: Reduce bigjoiner special casing")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211105212156.5697-1-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
We have to bash in a lot of registers to load the higher
precision LUT modes. The locking overhead is significant, especially
as we have to get this done as quickly as possible during vblank.
So let's switch to unlocked accesses for these. Fortunately the LUT
registers are mostly spread around such that two pipes do not have
any registers on the same cacheline. So as long as commits on the
same pipe are serialized (which they are) we should get away with
this without angering the hardware.
The only exceptions are the PREC_PIPEGCMAX registers on ilk/snb which
we don't use atm as they are only used in the 12bit gamma mode. If/when
we add support for that we may need to remember to still serialize
those registers, though I'm not sure ilk/snb are actually affected
by the same cacheline issue. I think ivb/hsw at least were, but they
use a different set of registers for the precision LUT.
I have a test case which is updating the LUTs on two pipes from a
single atomic commit. Running that in a loop for a minute I get the
following worst case with the locks in place:
intel_crtc_vblank_work_start: pipe B, frame=10037, scanline=1081
intel_crtc_vblank_work_start: pipe A, frame=12274, scanline=769
intel_crtc_vblank_work_end: pipe A, frame=12274, scanline=58
intel_crtc_vblank_work_end: pipe B, frame=10037, scanline=74
And here's the worst case with the locks removed:
intel_crtc_vblank_work_start: pipe B, frame=5869, scanline=1081
intel_crtc_vblank_work_start: pipe A, frame=7616, scanline=769
intel_crtc_vblank_work_end: pipe B, frame=5869, scanline=1096
intel_crtc_vblank_work_end: pipe A, frame=7616, scanline=777
The test was done on a snb using the 10bit 1024 entry LUT mode.
The vtotals for the two displays are 793 and 1125. So we can
see that with the locks ripped out the LUT updates are pretty
nicely confined within the vblank, whereas with the locks in
place we're routinely blasting past the vblank end which causes
visual artifacts near the top of the screen.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020223339.669-5-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
The pipe gamma registers are single buffered so they should only
be updated during the vblank to avoid screen tearing. In fact they
really should only be updated between start of vblank and frame
start because that is the only time the pipe is guaranteed to be
empty. Already at frame start the pipe begins to fill up with
data for the next frame.
Unfortunately frame start happens ~1 scanline after the start
of vblank which in practice doesn't always leave us enough time to
finish the gamma update in time (gamma LUTs can be several KiB of
data we have to bash into the registers). However we must try our
best and so we'll add a vblank work for each pipe from where we
can do the gamma update. Additionally we could consider pushing
frame start forward to the max of ~4 scanlines after start of
vblank. But not sure that's exactly a validated configuration.
As it stands the ~100 first pixels tend to make it through with
the old gamma values.
Even though the vblank worker is running on a high prority thread
we still have to contend with C-states. If the CPU happens be in
a deep C-state when the vblank interrupt arrives even the irq
handler gets delayed massively (I've observed dozens of scanlines
worth of latency). To avoid that problem we'll use the qos mechanism
to keep the CPU awake while the vblank work is scheduled.
With all this hooked up we can finally enjoy near atomic gamma
updates. It even works across several pipes from the same atomic
commit which previously was a total fail because we did the
gamma updates for each pipe serially after waiting for all
pipes to have latched the double buffered registers.
In the future the DSB should take over this responsibility
which will hopefully avoid some of these issues.
Kudos to Lyude for finishing the actual vblank workers.
Works like the proverbial train toilet.
v2: Add missing intel_atomic_state fwd declaration
v3: Clean up properly when not scheduling the worker
v4: Clean up the rest and add tracepoints
v5: s/intel_wait_for_vblank_works/intel_wait_for_vblank_workers/ (Jani,Uma)
CC: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020223339.669-4-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
Do the vrr push before we sample the frame counter to
know when the commit has been latched. Doing these in the
wrong order could lead us to complete the flip before it
has actually happened.
Cc: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020223339.669-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
[Why]
We need HPD IRQ notifications (RX, short pulse) to properly handle
DP MST for DPIA connections.
[How]
A null pointer exception currently occurs when these are received
so add a check to validate that we have a handler installed for
the notification.
Extend the HPD handler to also handle HPD IRQ (RX) since the logic is
the same.
Fixes: e27c41d5b068 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Jude Shih <shenshih@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
Per DRM spec we only need to hold that lock when touching
connector->state - which we do not do in that handler.
Taking this locking introduces unnecessary dependencies with other
threads which is bad for performance and opens up the potential for
a deadlock since there are multiple locks being held at once.
[How]
Remove the connection_mutex lock/unlock routine and just iterate over
the drm connectors normally. The iter helpers implicitly lock the
connection list so this is safe to do.
DC link access also does not need to be guarded since the link
table is static at creation - we don't dynamically add or remove links,
just streams.
Fixes: e27c41d5b068 ("drm/amd/display: Support for DMUB HPD interrupt handling")
Reviewed-by: Jude Shih <shenshih@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Trivial patch which adds a comment for macro
endif's in amdgpu_dm.c
Reviewed-by: Ariel Bernstein <Eric.Bernstein@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The check for whether to drain retry faults must be under the mmap write
lock to serialize with munmap notifier callbacks.
We were also missing checks on child ranges. To fix that, simplify the
logic by using a flag rather than checking on each prange. That also
allows draining less freqeuntly when many ranges are unmapped at once.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Tested-by: Philip Yang <Philip.Yang@amd.com>
Tested-by: Alex Sierra <Alex.Sierra@amd.com>
Reviewed-by: Philip Yang <Philip.Yang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The low 16MB of virtual address space are currently reserved for kernel
mode allocations mapped into user virtual address space. This causes
conflicts with HMM/SVM mappings at low virtual addresses. We tried to
move those kernel mode allocations to the upper half of the 64-bit
virtual address space for GFX9, which is naturally reserved for kernel
use. However, TBA (trap handler code) has problems to access addresses
in the high virtual space. We have decided to set this to 8KB of the
lower address space as a temporary fix, while investigate TBA address
problem. It is very unlikely for user space to map memory at this low
region.
Signed-off-by: Alex Sierra <alex.sierra@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
make action upon failure in "drm_atomic_add_affected_connectors()"
consistent with the rest of failures in amdgpu_dm_atomic_check().
Signed-off-by: Shirish S <shirish.s@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The KFD pre_reset should be called before reset been executed, it will
hold the lock to prevent other rocm process to sent the packlage to hiq
during host execute the real reset on the HW
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
There was a change(below) target for such issue:
d82e2c249c8f ("drm/amdgpu: Fix crash on device remove/driver unload")
But the fix for VI ASICs was missing there. This is a supplement for
that.
Fixes: d82e2c249c8f ("drm/amdgpu: Fix crash on device remove/driver unload")
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Don't set, test for, or clear per-engine reset bits with GuC submission
as the GuC owns the per engine resets not the i915. Setting, testing
for, and clearing these bits is causing issues with the hangcheck
selftest. Rather than change to test to not use these bits, rip the use
of these bits out from the reset code.
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211028224224.32693-1-matthew.brost@intel.com
|
|
Pull more block driver updates from Jens Axboe:
- Last series adding error handling support for add_disk() in drivers.
After this one, and once the SCSI side has been merged, we can
finally annotate add_disk() as must_check. (Luis)
- bcache fixes (Coly)
- zram fixes (Ming)
- ataflop locking fix (Tetsuo)
- nbd fixes (Ye, Yu)
- MD merge via Song
- Cleanup (Yang)
- sysfs fix (Guoqing)
- Misc fixes (Geert, Wu, luo)
* tag 'for-5.16/drivers-2021-11-09' of git://git.kernel.dk/linux-block: (34 commits)
bcache: Revert "bcache: use bvec_virt"
ataflop: Add missing semicolon to return statement
floppy: address add_disk() error handling on probe
ataflop: address add_disk() error handling on probe
block: update __register_blkdev() probe documentation
ataflop: remove ataflop_probe_lock mutex
mtd/ubi/block: add error handling support for add_disk()
block/sunvdc: add error handling support for add_disk()
z2ram: add error handling support for add_disk()
nvdimm/pmem: use add_disk() error handling
nvdimm/pmem: cleanup the disk if pmem_release_disk() is yet assigned
nvdimm/blk: add error handling support for add_disk()
nvdimm/blk: avoid calling del_gendisk() on early failures
nvdimm/btt: add error handling support for add_disk()
nvdimm/btt: use goto error labels on btt_blk_init()
loop: Remove duplicate assignments
drbd: Fix double free problem in drbd_create_device
nvdimm/btt: do not call del_gendisk() if not needed
bcache: fix use-after-free problem in bcache_device_free()
zram: replace fsync_bdev with sync_blockdev
...
|
|
Pull block fixes from Jens Axboe:
- Set of fixes for the batched tag allocation (Ming, me)
- add_disk() error handling fix (Luis)
- Nested queue quiesce fixes (Ming)
- Shared tags init error handling fix (Ye)
- Misc cleanups (Jean, Ming, me)
* tag 'for-5.16/block-2021-11-09' of git://git.kernel.dk/linux-block:
nvme: wait until quiesce is done
scsi: make sure that request queue queiesce and unquiesce balanced
scsi: avoid to quiesce sdev->request_queue two times
blk-mq: add one API for waiting until quiesce is done
blk-mq: don't free tags if the tag_set is used by other device in queue initialztion
block: fix device_add_disk() kobject_create_and_add() error handling
block: ensure cached plug request matches the current queue
block: move queue enter logic into blk_mq_submit_bio()
block: make bio_queue_enter() fast-path available inline
block: split request allocation components into helpers
block: have plug stored requests hold references to the queue
blk-mq: update hctx->nr_active in blk_mq_end_request_batch()
blk-mq: add RQF_ELV debug entry
blk-mq: only try to run plug merge if request has same queue with incoming bio
block: move RQF_ELV setting into allocators
dm: don't stop request queue after the dm device is suspended
block: replace always false argument with 'false'
block: assign correct tag before doing prefetch of request
blk-mq: fix redundant check of !e expression
|
|
Pull device mapper updates from Mike Snitzer:
- Add DM core support for emitting audit events through the audit
subsystem. Also enhance both the integrity and crypt targets to emit
events to via dm-audit.
- Various other simple code improvements and cleanups.
* tag 'for-5.16/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm table: log table creation error code
dm: make workqueue names device-specific
dm writecache: Make use of the helper macro kthread_run()
dm crypt: Make use of the helper macro kthread_run()
dm verity: use bvec_kmap_local in verity_for_bv_block
dm log writes: use memcpy_from_bvec in log_writes_map
dm integrity: use bvec_kmap_local in __journal_read_write
dm integrity: use bvec_kmap_local in integrity_metadata
dm: add add_disk() error handling
dm: Remove redundant flush_workqueue() calls
dm crypt: log aead integrity violations to audit subsystem
dm integrity: log audit events for dm-integrity target
dm: introduce audit event module for device mapper
|
|
Merge more updates from Andrew Morton:
"87 patches.
Subsystems affected by this patch series: mm (pagecache and hugetlb),
procfs, misc, MAINTAINERS, lib, checkpatch, binfmt, kallsyms, ramfs,
init, codafs, nilfs2, hfs, crash_dump, signals, seq_file, fork,
sysvfs, kcov, gdb, resource, selftests, and ipc"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (87 commits)
ipc/ipc_sysctl.c: remove fallback for !CONFIG_PROC_SYSCTL
ipc: check checkpoint_restore_ns_capable() to modify C/R proc files
selftests/kselftest/runner/run_one(): allow running non-executable files
virtio-mem: disallow mapping virtio-mem memory via /dev/mem
kernel/resource: disallow access to exclusive system RAM regions
kernel/resource: clean up and optimize iomem_is_exclusive()
scripts/gdb: handle split debug for vmlinux
kcov: replace local_irq_save() with a local_lock_t
kcov: avoid enable+disable interrupts if !in_task()
kcov: allocate per-CPU memory on the relevant node
Documentation/kcov: define `ip' in the example
Documentation/kcov: include types.h in the example
sysv: use BUILD_BUG_ON instead of runtime check
kernel/fork.c: unshare(): use swap() to make code cleaner
seq_file: fix passing wrong private data
seq_file: move seq_escape() to a header
signal: remove duplicate include in signal.h
crash_dump: remove duplicate include in crash_dump.h
crash_dump: fix boolreturn.cocci warning
hfs/hfsplus: use WARN_ON for sanity check
...
|
|
We don't want user space to be able to map virtio-mem device memory
directly (e.g., via /dev/mem) in order to have guarantees that in a sane
setup we'll never accidentially access unplugged memory within the
device-managed region of a virtio-mem device, just as required by the
virtio-spec.
As soon as the virtio-mem driver is loaded, the device region is visible
in /proc/iomem via the parent device region. From that point on user
space is aware of the device region and we want to disallow mapping
anything inside that region (where we will dynamically (un)plug memory)
until the driver has been unloaded cleanly and e.g., another driver might
take over.
By creating our parent IORESOURCE_SYSTEM_RAM resource with
IORESOURCE_EXCLUSIVE, we will disallow any /dev/mem access to our device
region until the driver was unloaded cleanly and removed the parent
region. This will work even though only some memory blocks are actually
currently added to Linux and appear as busy in the resource tree.
So access to the region from user space is only possible
a) if we don't load the virtio-mem driver.
b) after unloading the virtio-mem driver cleanly.
Don't build virtio-mem if access to /dev/mem cannot be restricticted -- if
we have CONFIG_DEVMEM=y but CONFIG_STRICT_DEVMEM is not set.
Link: https://lkml.kernel.org/r/20210920142856.17758-4-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
To print stack entries into a buffer, users of stackdepot, first get a
list of stack entries using stack_depot_fetch and then print this list
into a buffer using stack_trace_snprint. Provide a helper in stackdepot
for this purpose. Also change above mentioned users to use this helper.
[imran.f.khan@oracle.com: fix build error]
Link: https://lkml.kernel.org/r/20210915175321.3472770-4-imran.f.khan@oracle.com
[imran.f.khan@oracle.com: export stack_depot_snprint() to modules]
Link: https://lkml.kernel.org/r/20210916133535.3592491-4-imran.f.khan@oracle.com
Link: https://lkml.kernel.org/r/20210915014806.3206938-4-imran.f.khan@oracle.com
Signed-off-by: Imran Khan <imran.f.khan@oracle.com>
Suggested-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Jani Nikula <jani.nikula@intel.com> [i915]
Cc: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <andreyknvl@gmail.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: David Airlie <airlied@linux.ie>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
When kernel.h is used in the headers it adds a lot into dependency hell,
especially when there are circular dependencies are involved.
Replace kernel.h inclusion with the list of what is really being used.
[akpm@linux-foundation.org: cxd2880_common.h needs bits.h for GENMASK()]
[andriy.shevchenko@linux.intel.com: delay.h: fix for removed kernel.h]
Link: https://lkml.kernel.org/r/20211028170143.56523-1-andriy.shevchenko@linux.intel.com
[akpm@linux-foundation.org: include/linux/fwnode.h needs bits.h for BIT()]
Link: https://lkml.kernel.org/r/20211027150324.79827-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Although virtio-mem currently supports reading unplugged memory in the
hypervisor, this will change in the future, indicated to the device via
a new feature flag.
We similarly sanitized /proc/kcore access recently. [1]
Let's register a vmcore callback, to allow vmcore code to check if a PFN
belonging to a virtio-mem device is either currently plugged and should
be dumped or is currently unplugged and should not be accessed, instead
mapping the shared zeropage or returning zeroes when reading.
This is important when not capturing /proc/vmcore via tools like
"makedumpfile" that can identify logically unplugged virtio-mem memory
via PG_offline in the memmap, but simply by e.g., copying the file.
Distributions that support virtio-mem+kdump have to make sure that the
virtio_mem module will be part of the kdump kernel or the kdump initrd;
dracut was recently [2] extended to include virtio-mem in the generated
initrd. As long as no special kdump kernels are used, this will
automatically make sure that virtio-mem will be around in the kdump
initrd and sanitize /proc/vmcore access -- with dracut.
With this series, we'll send one virtio-mem state request for every ~2
MiB chunk of virtio-mem memory indicated in the vmcore that we intend to
read/map.
In the future, we might want to allow building virtio-mem for kdump mode
only, even without CONFIG_MEMORY_HOTPLUG and friends: this way, we could
support special stripped-down kdump kernels that have many other config
options disabled; we'll tackle that once required. Further, we might
want to try sensing bigger blocks (e.g., memory sections) first before
falling back to device blocks on demand.
Tested with Fedora rawhide, which contains a recent kexec-tools version
(considering "System RAM (virtio_mem)" when creating the vmcore header)
and a recent dracut version (including the virtio_mem module in the
kdump initrd).
Link: https://lkml.kernel.org/r/20210526093041.8800-1-david@redhat.com [1]
Link: https://github.com/dracutdevs/dracut/pull/1157 [2]
Link: https://lkml.kernel.org/r/20211005121430.30136-10-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let's prepare for a new virtio-mem kdump mode in which we don't actually
hot(un)plug any memory but only observe the state of device blocks.
Link: https://lkml.kernel.org/r/20211005121430.30136-9-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Let's prepare for a new virtio-mem kdump mode in which we don't actually
hot(un)plug any memory but only observe the state of device blocks.
Link: https://lkml.kernel.org/r/20211005121430.30136-8-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Wang <jasowang@redhat.com>
Cc: Juergen Gross <jgross@suse.com>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Mike Rapoport <rppt@kernel.org>
Cc: Oscar Salvador <osalvador@suse.de>
Cc: "Rafael J. Wysocki" <rafael.j.wysocki@intel.com>
Cc: Stefano Stabellini <sstabellini@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
Johan Hovold
Alistair Francis
Marek Vasut
Phoenix Huang
Colin Ian King
Taehee Yoo
Dave Airlie
Marek Behún
Alexandre Belloni
Dominique Martinet
John Harrison
Dan Carpenter
Ville Syrjälä
Nicholas Kazlauskas
Anson Jacob
Felix Kuehling
Alex Sierra
Shirish S
shaoyunl
Evan Quan
Matthew Brost
Linus Torvalds
David Hildenbrand
Imran Khan
Andy Shevchenko