| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
It seems that the PCIe+USB firmware (latest version 15.68.19.p21) of the
88W8897 card sometimes ignores or misses when we try to wake it up by
writing to the firmware status register. This leads to the firmware
wakeup timeout expiring and the driver resetting the card because we
assume the firmware has hung up or crashed.
Turns out that the firmware actually didn't hang up, but simply "missed"
our wakeup request and didn't send us an interrupt with an AWAKE event.
Trying again to read the firmware status register after a short timeout
usually makes the firmware wake up as expected, so add a small retry
loop to mwifiex_pm_wakeup_card() that looks at the interrupt status to
check whether the card woke up.
The number of tries and timeout lengths for this were determined
experimentally: The firmware usually takes about 500 us to wake up
after we attempt to read the status register. In some cases where the
firmware is very busy (for example while doing a bluetooth scan) it
might even miss our requests for multiple milliseconds, which is why
after 15 tries the waiting time gets increased to 10 ms. The maximum
number of tries it took to wake the firmware when testing this was
around 20, so a maximum number of 50 tries should give us plenty of
safety margin.
Here's a reproducer for those firmware wakeup failures I've found:
1) Make sure wifi powersaving is enabled (iw dev wlp1s0 set power_save on)
2) Connect to any wifi network (makes firmware go into wifi powersaving
mode, not deep sleep)
3) Make sure bluetooth is turned off (to ensure the firmware actually
enters powersave mode and doesn't keep the radio active doing bluetooth
stuff)
4) To confirm that wifi powersaving is entered ping a device on the LAN,
pings should be a few ms higher than without powersaving
5) Run "while true; do iwconfig; sleep 0.0001; done", this wakes and
suspends the firmware extremely often
6) Wait until things explode, for me it consistently takes <5 minutes
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-3-verdre@v0yd.nl
|
|
On the 88W8897 PCIe+USB card the firmware randomly crashes after setting
the TX ring write pointer. The issue is present in the latest firmware
version 15.68.19.p21 of the PCIe+USB card.
Those firmware crashes can be worked around by reading any PCI register
of the card after setting that register, so read the PCI_VENDOR_ID
register here. The reason this works is probably because we keep the bus
from entering an ASPM state for a bit longer, because that's what causes
the cards firmware to crash.
This fixes a bug where during RX/TX traffic and with ASPM L1 substates
enabled (the specific substates where the issue happens appear to be
platform dependent), the firmware crashes and eventually a command
timeout appears in the logs.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=109681
Cc: stable@vger.kernel.org
Signed-off-by: Jonas Dreßler <verdre@v0yd.nl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211011133224.15561-2-verdre@v0yd.nl
|
|
Setting ds->num_ports to DSA_MAX_PORTS made DSA core allocate unnecessary
dsa_port's and call mt7530_port_disable for non-existent ports.
Set it to MT7530_NUM_PORTS to fix that, and dsa_is_user_port check in
port_enable/disable is no longer required.
Cc: stable@vger.kernel.org
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I compared the register definitions with the D-Link DWR-966
GPL sources and found that the PUAFD field definition was
incorrect. This definition is unused and causes no issues.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount
of VLANs...") introduced a rbtree for faster Ethernet address look
up. To maintain netdev->dev_addr in this tree we need to make all
the writes to it got through appropriate helpers.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the poll queue flag to enable polling, given that the multipath
node just dispatches the bios to a lower queue.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Mark Wunderlich <mark.wunderlich@intel.com>
Link: https://lore.kernel.org/r/20211012111226.760968-17-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Replace the blk_poll interface that requires the caller to keep a queue
and cookie from the submissions with polling based on the bio.
Polling for the bio itself leads to a few advantages:
- the cookie construction can made entirely private in blk-mq.c
- the caller does not need to remember the request_queue and cookie
separately and thus sidesteps their lifetime issues
- keeping the device and the cookie inside the bio allows to trivially
support polling BIOs remapping by stacking drivers
- a lot of code to propagate the cookie back up the submission path can
be removed entirely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Tested-by: Mark Wunderlich <mark.wunderlich@intel.com>
Link: https://lore.kernel.org/r/20211012111226.760968-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Unlike the RWF_HIPRI userspace ABI which is intentionally kept vague,
the bio flag is specific to the polling implementation, so rename and
document it properly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Chaitanya Kulkarni <chaitanya.kulkarni@wdc.com>
Tested-by: Mark Wunderlich <mark.wunderlich@intel.com>
Link: https://lore.kernel.org/r/20211012111226.760968-12-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
It is a bit confusing that there is BLKDEV_MAX_RQ and MAX_SCHED_RQ, as
the name BLKDEV_MAX_RQ would imply the max requests always, which it is
not.
Rename to BLKDEV_MAX_RQ to BLKDEV_DEFAULT_RQ, matching its usage - that being
the default number of requests assigned when allocating a request queue.
Signed-off-by: John Garry <john.garry@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Link: https://lore.kernel.org/r/1633429419-228500-3-git-send-email-john.garry@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
struct request is only used by blk-mq drivers, so move it and all
related declarations to blk-mq.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-18-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Split the integrity/metadata handling definitions out into a new header.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-17-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Drop various include not actually used in genhd.h itself, and
move the remaning includes closer together.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-15-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Drop various include not actually used in blkdev.h itself.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-14-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Except for the features passed to blk_queue_required_elevator_features,
elevator.h is only needed internally to the block layer. Move the
ELEVATOR_F_* definitions to blkdev.h, and the move elevator.h to
block/, dropping all the spurious includes outside of that.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-13-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-9-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Move inode_to_bdi out of line to avoid having to include blkdev.h.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-4-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There is no need to pull blk-cgroup.h and thus blkdev.h in here, so
break the include chain.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-3-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
blk-cgroup.h pulls in blkdev.h and thus pretty much all the block
headers. Break this dependency chain by turning wbc_blkcg_css into a
macro and dropping the blk-cgroup.h include.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Link: https://lore.kernel.org/r/20210920123328.1399408-2-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Building the VF and PF side of this driver differently, with one being
a loadable module and the other one built-in results in a link failure
for the common PTP driver:
ld.lld: error: undefined symbol: __this_module
>>> referenced by otx2_ptp.c
>>> net/ethernet/marvell/octeontx2/nic/otx2_ptp.o:(otx2_ptp_init) in archive drivers/built-in.a
>>> referenced by otx2_ptp.c
>>> net/ethernet/marvell/octeontx2/nic/otx2_ptp.o:(otx2_ptp_init) in archive drivers/built-in.a
Move the otx2_ptp.c code into a separate module that gets built for
both configurations, making it built-in if at least one of the other
two is built-in.
Fixes: 43510ef4ddad ("octeontx2-nicvf: Add PTP hardware clock support to NIX VF")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of the FF-A spec, an endpoint is allowed to transfer access of,
or lend, a memory region to one or more borrowers.
Extend the existing memory sharing implementation to support
FF-A MEM_LEND functionality and expose this to other kernel drivers.
Note that upon a successful MEM_LEND request the caller must ensure that
the memory region specified is not accessed until a successful
MEM_RECALIM call has been made. On systems with a hypervisor present
this will been enforced, however on systems without a hypervisor the
responsibility falls to the calling kernel driver to prevent access.
Link: https://lore.kernel.org/r/20211015165742.2513065-1-marc.bonnici@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Marc Bonnici <marc.bonnici@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
The driver currently just support v1.0 of Arm FFA specification. It also
expects the firmware implementation to match the same and bail out if it
doesn't match. This is causing issue when running with higher version of
firmware implementation(e.g. v1.1 which will released soon).
In order to support compatibility with different firmware versions, let
us add additional checks and find the compatible version the driver can
work with.
Link: https://lore.kernel.org/r/20211013091127.990992-1-sudeep.holla@arm.com
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
Add basic support for UniPhier NX1 SoC. This includes a compatible string
and SoC-dependent data.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch extends sparx5 driver to support also the lan966x. The
process to reset the switch is the same only it has different offsets.
Therefore make the driver more generic and add support for lan966x.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Steen Hegelund <steen.hegelund@microchip.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20211018091522.1113510-3-horatiu.vultur@microchip.com
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Marc Kleine-Budde says:
====================
pull-request: can 2021-10-17
this is a pull request of 11 patches for net/master.
The first 4 patches are by Ziyang Xuan and Zhang Changzhong and fix 1
use after free and 3 standard conformance problems in the j1939 CAN
stack.
The next 2 patches are by Ziyang Xuan and fix 2 concurrency problems
in the ISOTP CAN stack.
Yoshihiro Shimoda's patch for the rcar_can fix suspend/resume on not
running CAN interfaces.
Aswath Govindraju's patch for the m_can driver fixes access for MMIO
devices.
Zheyu Ma contributes a patch for the peak_pci driver to fix a use
after free.
Stephane Grosjean's 2 patches fix CAN error state handling in the
peak_usb driver.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add basic support for UniPhier NX1 SoC. This includes a compatible string
and the same SoC-dependent data as LD20 SoC.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1634520891-16801-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Up to now w5100_remove() returns zero unconditionally. Make it return
void instead which makes it easier to see in the callers that there is
no error to handle.
Also the return value of platform and spi remove callbacks is ignored
anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up to now ks8851_remove_common() returns zero unconditionally. Make it
return void instead which makes it easier to see in the callers that
there is no error to handle.
Also the return value of platform and spi remove callbacks is ignored
anyway.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On i386, the baycom_epp driver wants to inspect X86 CPU features (TSC)
and then act on that data, but that info is not available when running
on UML, so prevent that test and do the default action.
Prevents this build error on UML + i386:
../drivers/net/hamradio/baycom_epp.c: In function ‘epp_bh’:
../drivers/net/hamradio/baycom_epp.c:630:6: error: implicit declaration of function ‘boot_cpu_has’; did you mean ‘get_cpu_mask’? [-Werror=implicit-function-declaration]
if (boot_cpu_has(X86_FEATURE_TSC)) \
^
../drivers/net/hamradio/baycom_epp.c:658:2: note: in expansion of macro ‘GETTICK’
GETTICK(time1);
Fixes: 68f5d3f3b654 ("um: add PCI over virtio emulation driver")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: linux-um@lists.infradead.org
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Anton Ivanov <anton.ivanov@cambridgegreys.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Thomas Sailer <t.sailer@alumni.ethz.ch>
Cc: linux-hams@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The only factor differentiating per-CPU bstats data type (struct
gnet_stats_basic_cpu) from the packed non-per-CPU one (struct
gnet_stats_basic_packed) was a u64_stats sync point inside the former.
The two data types are now equivalent: earlier commits added a u64_stats
sync point to the latter.
Combine both data types into "struct gnet_stats_basic_sync". This
eliminates redundancy and simplifies the bstats read/write APIs.
Use u64_stats_t for bstats "packets" and "bytes" data types. On 64-bit
architectures, u64_stats sync points do not use sequence counter
protection.
Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'smmu->asids' is a bitmap. So use 'devm_kzalloc()' to simplify code,
improve the semantic of the code and avoid some open-coded arithmetic in
allocator arguments.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/2c0f4da80c3b5ef83299c651f69a563034c1c6cb.1632661557.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Fix following coccicheck warning:
drivers/iommu/apple-dart.c:704:20-27: WARNING opportunity for kmemdup
Signed-off-by: Wan Jiabing <wanjiabing@vivo.com>
Acked-by: Sven Peter <sven@svenpeter.dev>
Reviewed-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://lore.kernel.org/r/20211013063441.29888-1-wanjiabing@vivo.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The __domain_mapping() always removes the pages in the range from
'iov_pfn' to 'end_pfn', but the 'end_pfn' is always the last pfn
of the range that the caller wants to map.
This would introduce too many duplicated removing and leads the
map operation take too long, for example:
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x7e617ff
iov_pfn: 0x140000, end_pfn: 0x7e617ff
iov_pfn: 0x180000, end_pfn: 0x7e617ff
iov_pfn: 0x1c0000, end_pfn: 0x7e617ff
iov_pfn: 0x200000, end_pfn: 0x7e617ff
...
it takes about 50ms in total.
We can reduce the cost by recalculate the 'end_pfn' and limit it
to the boundary of the end of this pte page.
Map iova=0x100000,nr_pages=0x7d61800
iov_pfn: 0x100000, end_pfn: 0x13ffff
iov_pfn: 0x140000, end_pfn: 0x17ffff
iov_pfn: 0x180000, end_pfn: 0x1bffff
iov_pfn: 0x1c0000, end_pfn: 0x1fffff
iov_pfn: 0x200000, end_pfn: 0x23ffff
...
it only need 9ms now.
This also removes a meaningless BUG_ON() in __domain_mapping().
Signed-off-by: Longpeng(Mike) <longpeng2@huawei.com>
Tested-by: Liujunjie <liujunjie23@huawei.com>
Link: https://lore.kernel.org/r/20211008000433.1115-1-longpeng2@huawei.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-10-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
update_pasid() and its call chain are currently unused in the tree because
Thomas disabled the ENQCMD feature. The feature will be re-enabled shortly
using a different approach and update_pasid() and its call chain will not
be used in the new approach.
Remove the useless functions.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Reviewed-by: Tony Luck <tony.luck@intel.com>
Link: https://lore.kernel.org/r/20210920192349.2602141-1-fenghua.yu@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-8-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The commit 262948f8ba573 ("iommu: Delete iommu_dev_has_feature()") has
deleted the iommu_dev_has_feature() interface. Remove the dev_has_feat
callback to avoid dead code.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20210929072030.1330225-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-7-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The IOMMU VT-d implementation uses the first level for GPA->HPA translation
by default. Although both the first level and the second level could handle
the DMA translation, they're different in some way. For example, the second
level translation has separate controls for the Access/Dirty page tracking.
With the first level translation, there's no such control. On the other
hand, the second level translation has the page-level control for forcing
snoop, but the first level only has global control with pasid granularity.
This uses the second level for GPA->HPA translation so that we can provide
a consistent hardware interface for use cases like dirty page tracking for
live migration.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-6-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
An iommu domain could be allocated and mapped before it's attached to any
device. This requires that in scalable mode, when the domain is allocated,
the format (FL or SL) of the page table must be determined. In order to
achieve this, the platform should support consistent SL or FL capabilities
on all IOMMU's. This adds a check for this and aborts IOMMU probing if it
doesn't meet this requirement.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-5-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The iommu_domain data structure already has the "type" field to keep the
type of a domain. It's unnecessary to have the DOMAIN_FLAG_STATIC_IDENTITY
flag in the vt-d implementation. This cleans it up with no functionality
change.
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Kevin Tian <kevin.tian@intel.com>
Link: https://lore.kernel.org/r/20210926114535.923263-1-baolu.lu@linux.intel.com
Link: https://lore.kernel.org/r/20211014053839.727419-4-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When the dmar translation fault happens, the kernel prints a single line
fault reason with corresponding hexadecimal code defined in the Intel VT-d
specification.
Currently, when user wants to debug the translation fault in detail,
debugfs is used for dumping the dmar_translation_struct, which is not
available when the kernel failed to boot.
Dump the DMAR translation structure, pagewalk the IO page table and print
the page table entry when the fault happens.
This takes effect only when CONFIG_DMAR_DEBUG is enabled.
Signed-off-by: Kyung Min Park <kyung.min.park@intel.com>
Link: https://lore.kernel.org/r/20210815203845.31287-1-kyung.min.park@intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-3-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Handling of intel_iommu kernel command line option should return "true" to
indicate option is valid and so avoid logging it as unknown by the core
parsing code.
Also log unknown sub-options at the notice level to let user know of
potential typos or similar.
Reported-by: Eero Tamminen <eero.t.tamminen@intel.com>
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://lore.kernel.org/r/20210831112947.310080-1-tvrtko.ursulin@linux.intel.com
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Link: https://lore.kernel.org/r/20211014053839.727419-2-baolu.lu@linux.intel.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Replace the unconditional clflush() with drm_clflush_virt_range()
which does the wbinvd() fallback when clflush is not available.
This time no justification is given for the clflush in the
offending commit.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Fixes: 2c8ab3339e39 ("drm/i915: Pin timeline map after first timeline pin, v4.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014090941.12159-4-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
|
|
This one is apparently a "clflush for good measure", so bit more
justification (if you can call it that) than some of the others.
Convert to drm_clflush_virt_range() again so that machines without
clflush will survive the ordeal.
Cc: stable@vger.kernel.org
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Thomas Hellström <thomas.hellstrom@intel.com> #v1
Fixes: 12ca695d2c1e ("drm/i915: Do not share hwsp across contexts any more, v8.")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014090941.12159-3-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
|
|
Not all machines have clflush, so don't go assuming they do.
Not really sure why the clflush is even here since hwsp
is supposed to get snooped I thought.
Although in my case we're talking about a i830 machine where
render/blitter snooping is definitely busted. But it might
work for the hswp perhaps. Haven't really reverse engineered
that one fully.
Cc: stable@vger.kernel.org
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Fixes: b436a5f8b6c8 ("drm/i915/gt: Track all timelines created using the HWSP")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211014090941.12159-2-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
|
|
Adds support for using FF-A [1] as transport to the OP-TEE driver.
Introduces struct optee_msg_param_fmem which carries all information
needed when OP-TEE is calling FFA_MEM_RETRIEVE_REQ to get the shared
memory reference mapped by the hypervisor in S-EL2. Register usage is
also updated to include the information needed.
The FF-A part of this driver is enabled if CONFIG_ARM_FFA_TRANSPORT is
enabled.
[1] https://developer.arm.com/documentation/den0077/latest
Acked-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
Isolate the ABI based on raw SMCs. Code specific to the raw SMC ABI is
moved into smc_abi.c. This makes room for other ABIs with a clear
separation.
The driver changes to use module_init()/module_exit() instead of
module_platform_driver(). The platform_driver_register() and
platform_driver_unregister() functions called directly to keep the same
behavior. This is needed because module_platform_driver() is based on
module_driver() which can only be used once in a module.
A function optee_rpc_cmd() is factored out from the function
handle_rpc_func_cmd() to handle the ABI independent part of RPC
processing.
This patch is not supposed to change the driver behavior, it's only a
matter of reorganizing the code.
Reviewed-by: Sumit Garg <sumit.garg@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
|
|
intel_load_plane_csc_black() is specific to icl+ so deserves
a name reflecting that fact. Also rename the variables to
standard form so I won't get confused reading the code.
v2: icl+ not glk+
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-5-ville.syrjala@linux.intel.com
Reviewed-by: Juston Li <juston.li@intel.com>
|
|
We are inside the vblank evade critical section here, racing
against the raster beam. There is no time to print debug
messages.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-4-ville.syrjala@linux.intel.com
Reviewed-by: Juston Li <juston.li@intel.com>
|
|
There's lots of expensive stuff inserted between the PLANE_CTL
and PLANE_SURF writes even though the comment before the PLANE_CTL
write says not to put stuff there. Move it all to a more apporiate
place.
There's also a weird PLANE_COLOR_CTL RMW in there. I guess because
force_black was computed way too late originally, but that is now
sorted.
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
No real reason to have this pxp state computation in
intel_atomic_check_planes(). Just stuff it into skl_plane_check().
There was also some funny state copying being done from the
old plane state to the new plane state when the plane is anyway
disabled.
The one thing we presumably must remember to do is copy
over the decrypt state when assigning a Y plane for planar
YCbCr scanout, so that the Y plane's PLANE_SURF will get the
appropriate bit set. The force_black thing should not matter
as I'm pretty sure all that stuff is ignored for the Y plane.
I suppose this was the reason for the odd placement for the
state computation, but I see no reason to deviate from the
standard way of doing these things. This also guarantees
that we don't calculate things differently between the
linked UV and Y plane.
v2: Only do stuff for icl+ since 'force_black' depends
on the plane CSC which is an icl+ feature
Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Juston Li <juston.li@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211006235704.28894-2-ville.syrjala@linux.intel.com
Reviewed-by: Juston Li <juston.li@intel.com> #v1
|
|
To avoid checking if fence exists multipled times, changed fence
handling to depend only on the fence status field:
Busy, which means CS still did not completed :
Add its QID so multi CS wait on its completion.
Finished, which means CS completed and fence exists:
Raise its completion bit if it finished mcs handling and
update if necessary the earliest timestamp.
Gone, which means CS already completed and fence deleted:
Update multi CS data to ignore timestamp and raise its
completion bit.
Signed-off-by: Dani Liberman <dliberman@habana.ai>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
|
No need to check the return value if the following action is the same for
both cases. In addition, now that hl_ctx_free() doesn't print if the
context is not released, its name can be misleading as the context might
stay alive after it is executed with no indication for that.
Hence we can discard it and simply put the refcount.
Signed-off-by: Omer Shpigelman <oshpigelman@habana.ai>
Reviewed-by: Oded Gabbay <ogabbay@kernel.org>
Signed-off-by: Oded Gabbay <ogabbay@kernel.org>
|
Jonas Dreßler
DENG Qingfang
Aleksander Jan Bajkowski
Jakub Kicinski
Christoph Hellwig
John Garry
Arnd Bergmann
Marc Bonnici
Sudeep Holla
Kunihiko Hayashi
Horatiu Vultur
David S. Miller
Uwe Kleine-König
Randy Dunlap
Ahmed S. Darwish
Christophe JAILLET
Wan Jiabing
Longpeng(Mike)
Fenghua Yu
Lu Baolu
Kyung Min Park
Tvrtko Ursulin
Ville Syrjälä
Jens Wiklander
Dani Liberman
Omer Shpigelman