| Age | Commit message (Collapse) | Author | Files | Lines |
|---|
|
If 'copy_dma_range_map() fails, the memory allocated for 'rvdev' will leak.
Move the 'copy_dma_range_map()' call after the device registration so
that 'rproc_rvdev_release()' can be called to free some resources.
Also, branch to the error handling path if 'copy_dma_range_map()' instead
of a direct return to avoid some other leaks.
Fixes: e0d072782c73 ("dma-mapping: introduce DMA range map, supplanting dma_pfn_offset")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Jim Quinlan <james.quinlan@broadcom.com>
Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/e6d0dad6620da4fdf847faa903f79b735d35f262.1630755377.git.christophe.jaillet@wanadoo.fr
|
|
There are spelling mistakes dev_err messages. Fix them.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210826123735.14650-1-colin.king@canonical.com
|
|
Go through the code base and use ice_for_each_* macros. While at it,
introduce ice_for_each_xdp_txq() macro that can be used for looping over
xdp_rings array.
Commit is not introducing any new functionality.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Under rare circumstances there might be a situation where a requirement
of having XDP Tx queue per CPU could not be fulfilled and some of the Tx
resources have to be shared between CPUs. This yields a need for placing
accesses to xdp_ring inside a critical section protected by spinlock.
These accesses happen to be in the hot path, so let's introduce the
static branch that will be triggered from the control plane when driver
could not provide Tx queue dedicated for XDP on each CPU.
Currently, the design that has been picked is to allow any number of XDP
Tx queues that is at least half of a count of CPUs that platform has.
For lower number driver will bail out with a response to user that there
were not enough Tx resources that would allow configuring XDP. The
sharing of rings is signalled via static branch enablement which in turn
indicates that lock for xdp_ring accesses needs to be taken in hot path.
Approach based on static branch has no impact on performance of a
non-fallback path. One thing that is needed to be mentioned is a fact
that the static branch will act as a global driver switch, meaning that
if one PF got out of Tx resources, then other PFs that ice driver is
servicing will suffer. However, given the fact that HW that ice driver
is handling has 1024 Tx queues per each PF, this is currently an
unlikely scenario.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Optimize Tx descriptor cleaning for XDP. Current approach doesn't
really scale and chokes when multiple flows are handled.
Introduce two ring fields, @next_dd and @next_rs that will keep track of
descriptor that should be looked at when the need for cleaning arise and
the descriptor that should have the RS bit set, respectively.
Note that at this point the threshold is a constant (32), but it is
something that we could make configurable.
First thing is to get away from setting RS bit on each descriptor. Let's
do this only once NTU is higher than the currently @next_rs value. In
such case, grab the tx_desc[next_rs], set the RS bit in descriptor and
advance the @next_rs by a 32.
Second thing is to clean the Tx ring only when there are less than 32
free entries. For that case, look up the tx_desc[next_dd] for a DD bit.
This bit is written back by HW to let the driver know that xmit was
successful. It will happen only for those descriptors that had RS bit
set. Clean only 32 descriptors and advance the DD bit.
Actual cleaning routine is moved from ice_napi_poll() down to the
ice_xmit_xdp_ring(). It is safe to do so as XDP ring will not get any
SKBs in there that would rely on interrupts for the cleaning. Nice side
effect is that for rare case of Tx fallback path (that next patch is
going to introduce) we don't have to trigger the SW irq to clean the
ring.
With those two concepts, ring is kept at being almost full, but it is
guaranteed that driver will be able to produce Tx descriptors.
This approach seems to work out well even though the Tx descriptors are
produced in one-by-one manner. Test was conducted with the ice HW
bombarded with packets from HW generator, configured to generate 30
flows.
Xdp2 sample yields the following results:
<snip>
proto 17: 79973066 pkt/s
proto 17: 80018911 pkt/s
proto 17: 80004654 pkt/s
proto 17: 79992395 pkt/s
proto 17: 79975162 pkt/s
proto 17: 79955054 pkt/s
proto 17: 79869168 pkt/s
proto 17: 79823947 pkt/s
proto 17: 79636971 pkt/s
</snip>
As that sample reports the Rx'ed frames, let's look at sar output.
It says that what we Rx'ed we do actually Tx, no noticeable drops.
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 79842324.00 79842310.40 4678261.17 4678260.38 0.00 0.00 0.00 38.32
with tx_busy staying calm.
When compared to a state before:
Average: IFACE rxpck/s txpck/s rxkB/s txkB/s rxcmp/s txcmp/s rxmcst/s %ifutil
Average: ens4f1 90919711.60 42233822.60 5327326.85 2474638.04 0.00 0.00 0.00 43.64
it can be observed that the amount of txpck/s is almost doubled, meaning
that the performance is improved by around 90%. All of this due to the
drops in the driver, previously the tx_busy stat was bumped at a 7mpps
rate.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
With rings being split, it is now convenient to introduce a pointer to
XDP ring within the Rx ring. For XDP_TX workloads this means that
xdp_rings array access will be skipped, which was executed per each
processed frame.
Also, read the XDP prog once per NAPI and if prog is present, set up the
local xdp_ring pointer. Reading prog a single time was discussed in [1]
with some concern raised by Toke around dispatcher handling and having
the need for going through the RCU grace period in the ndo_bpf driver
callback, but ice currently is torning down NAPI instances regardless of
the prog presence on VSI.
Although the pointer to XDP ring introduced to Rx ring makes things a
lot slimmer/simpler, I still feel that single prog read per NAPI
lifetime is beneficial.
Further patch that will introduce the fallback path will also get a
profit from that as xdp_ring pointer will be set during the XDP rings
setup.
[1]: https://lore.kernel.org/bpf/87k0oseo6e.fsf@toke.dk/
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
xdp_frame is not needed for XDP_TX data path in ice driver case.
For this data path cleaning of sent descriptor will not happen anywhere
outside of the driver, which means that carrying the information about
the underlying memory model via xdp_frame will not be used. Therefore,
this conversion can be simply dropped, which would relieve CPU a bit.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There has been a long lasting issue of improper xdp_rings indexing for
XDP_TX and XDP_REDIRECT actions. Given that currently rx_ring->q_index
is mixed with smp_processor_id(), there could be a situation where Tx
descriptors are produced onto XDP Tx ring, but tail is never bumped -
for example pin a particular queue id to non-matching IRQ line.
Address this problem by ignoring the user ring count setting and always
initialize the xdp_rings array to be of num_possible_cpus() size. Then,
always use the smp_processor_id() as an index to xdp_rings array. This
provides serialization as at given time only a single softirq can run on
a particular CPU.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
While it was convenient to have a generic ring structure that served
both Tx and Rx sides, next commits are going to introduce several
Tx-specific fields, so in order to avoid hurting the Rx side, let's
pull out the Tx ring onto new ice_tx_ring and ice_rx_ring structs.
Rx ring could be handled by the old ice_ring which would reduce the code
churn within this patch, but this would make things asymmetric.
Make the union out of the ring container within ice_q_vector so that it
is possible to iterate over newly introduced ice_tx_ring.
Remove the @size as it's only accessed from control path and it can be
calculated pretty easily.
Change definitions of ice_update_ring_stats and
ice_fetch_u64_stats_per_ring so that they are ring agnostic and can be
used for both Rx and Tx rings.
Sizes of Rx and Tx ring structs are 256 and 192 bytes, respectively. In
Rx ring xdp_rxq_info occupies its own cacheline, so it's the major
difference now.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently ice_container_type is scoped only for ice_ethtool.c. Next
commit that will split the ice_ring struct onto Rx/Tx specific ring
structs is going to also modify the type of linked list of rings that is
within ice_ring_container. Therefore, the functions that are taking the
ice_ring_container as an input argument will need to be aware of a ring
type that will be looked up.
Embed ice_container_type within ice_ring_container and initialize it
properly when allocating the q_vectors.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
This field is dead and driver is not making any use of it. Simply remove
it.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Gurucharan G <gurucharanx.g@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Pull gpio fixes from Bartosz Golaszewski:
- fix module autoloading on gpio-74x164 after a revert of OF modaliases
- fix problems with the bias setting in gpio-pca953x
- fix a use-after-free bug in gpio-mockup by using software nodes
* tag 'gpio-fixes-for-v5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux:
gpio: mockup: Convert to use software nodes
gpio: pca953x: Improve bias setting
gpio: 74x164: Add SPI device ID table
|
|
Pull spi fixes from Mark Brown:
"A few small fixes.
Mostly driver specific but there's one in the core which fixes a
deadlock when adding devices on spi-mux that's triggered because
spi-mux is a SPI device which is itself a SPI controller and so can
instantiate devices when registered.
We were using a global lock to protect against reusing chip selects
but they're a per controller thing so moving the lock per controller
resolves that"
* tag 'spi-fix-v5.15-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi-mux: Fix false-positive lockdep splats
spi: Fix deadlock when adding SPI controllers on SPI buses
spi: bcm-qspi: clear MSPI spifie interrupt during probe
spi: spi-nxp-fspi: don't depend on a specific node name erratum workaround
spi: mediatek: skip delays if they are 0
spi: atmel: Fix PDC transfer setup bug
spi: spidev: Add SPI ID table
spi: Use 'flash' node name instead of 'spi-flash' in example
|
|
Pull mtd fix from Miquel Raynal:
"Raw NAND controller driver fix:
- Qcom: Update code word value for raw reads (QPIC v2+)"
* tag 'mtd/fixes-for-5.15-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux:
mtd: rawnand: qcom: Update code word value for raw read
|
|
Pull drm fixes from Dave Airlie:
"It has a few scattered msm and i915 fixes, a few core fixes and a
mediatek feature revert.
I've had to pick a bunch of patches into this, as the drm-misc-fixes
tree had a bunch of vc4 patches I wasn't comfortable with sending to
you at least as part of this, they were delayed due to your reverts.
If it's really useful as fixes I'll do a separate pull.
Summary:
Core:
- clamp fbdev size
- edid cap blocks read to avoid out of bounds
panel:
- fix missing crc32 dependency
msm:
- Fix a new crash on dev file close if the dev file was opened when
GPU is not loaded (such as missing fw in initrd)
- Switch to single drm_sched_entity per priority level per drm_file
to unbreak multi-context userspace
- Serialize GMU access to fix GMU OOB errors
- Various error path fixes
- A couple integer overflow fixes
- Fix mdp5 cursor plane WARNs
i915:
- Fix ACPI object leak
- Fix context leak in user proto-context creation
- Fix missing i915_sw_fence_fini call
hyperv:
- hide hw pointer
nouveau:
- fix engine selection bit
r128:
- fix UML build
rcar-du:
- unconncted LVDS regression fix
mediatek:
- revert CMDQ refinement patches"
* tag 'drm-fixes-2021-10-15-1' of git://anongit.freedesktop.org/drm/drm: (34 commits)
drm/panel: olimex-lcd-olinuxino: select CRC32
drm/r128: fix build for UML
drm/nouveau/fifo: Reinstate the correct engine bit programming
drm/hyperv: Fix double mouse pointers
drm/fbdev: Clamp fbdev surface size if too large
drm/edid: In connector_bad_edid() cap num_of_ext by num_blocks read
drm/i915: Free the returned object of acpi_evaluate_dsm()
drm/i915: Fix bug in user proto-context creation that leaked contexts
drm: rcar-du: Don't create encoder for unconnected LVDS outputs
drm/msm/dsi: fix off by one in dsi_bus_clk_enable error handling
drm/msm/dsi: Fix an error code in msm_dsi_modeset_init()
drm/msm/dsi: dsi_phy_14nm: Take ready-bit into account in poll_for_ready
drm/msm/dsi/phy: fix clock names in 28nm_8960 phy
drm/msm/dpu: Fix address of SM8150 PINGPONG5 IRQ register
drm/msm: Do not run snapshot on non-DPU devices
drm/msm/a3xx: fix error handling in a3xx_gpu_init()
drm/msm/a4xx: fix error handling in a4xx_gpu_init()
drm/msm: Fix null pointer dereference on pointer edp
drm/msm/mdp5: fix cursor-related warnings
drm/msm: Avoid potential overflow in timeout_to_jiffies()
...
|
|
Use the samsung common clk driver to initialize the apollo and atlas
clocks. This removes their custom init functions and uses the
samsung_cmu_register_one() instead.
Signed-off-by: Will McVicker <willmcvicker@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211014195347.3635601-3-willmcvicker@google.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Adds 'struct samsung_cpu_clock' and corresponding CPU clock registration
function to the samsung common clk driver. This allows samsung clock
drivers to register their CPU clocks with the samsung_cmu_register_one()
API.
Currently the exynos5433 apollo and atlas clks have their own custom
init functions to handle registering their CPU clocks. With this patch
we can drop their custom CLK_OF_DECLARE functions and directly call
samsung_cmu_register_one().
Signed-off-by: Will McVicker <willmcvicker@google.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Link: https://lore.kernel.org/r/20211014195347.3635601-2-willmcvicker@google.com
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
When device_register() return failed, program will goto out_kfree_type
to release 'cdev->device' by put_device(). That will call thermal_release()
to free 'cdev'. But the follow-up processes access 'cdev' continually.
That trggers the UAF bug.
====================================================================
BUG: KASAN: use-after-free in __thermal_cooling_device_register+0x75b/0xa90
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1.1 04/01/2014
Call Trace:
dump_stack_lvl+0xe2/0x152
print_address_description.constprop.0+0x21/0x140
? __thermal_cooling_device_register+0x75b/0xa90
kasan_report.cold+0x7f/0x11b
? __thermal_cooling_device_register+0x75b/0xa90
__thermal_cooling_device_register+0x75b/0xa90
? memset+0x20/0x40
? __sanitizer_cov_trace_pc+0x1d/0x50
? __devres_alloc_node+0x130/0x180
devm_thermal_of_cooling_device_register+0x67/0xf0
max6650_probe.cold+0x557/0x6aa
......
Freed by task 258:
kasan_save_stack+0x1b/0x40
kasan_set_track+0x1c/0x30
kasan_set_free_info+0x20/0x30
__kasan_slab_free+0x109/0x140
kfree+0x117/0x4c0
thermal_release+0xa0/0x110
device_release+0xa7/0x240
kobject_put+0x1ce/0x540
put_device+0x20/0x30
__thermal_cooling_device_register+0x731/0xa90
devm_thermal_of_cooling_device_register+0x67/0xf0
max6650_probe.cold+0x557/0x6aa [max6650]
Do not use 'cdev' again after put_device() to fix the problem like doing
in thermal_zone_device_register().
[dlezcano]: as requested by Rafael, change the affectation into two statements.
Fixes: 584837618100 ("thermal/drivers/core: Use a char pointer for the cooling device name")
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Reported-by: kernel test robot <lkp@intel.com>
Link: https://lore.kernel.org/r/20211015024504.947520-1-william.xuanziyang@huawei.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This is the initial implementation adding only basic clocks like UART,
MMC, I2C and corresponding parent clocks. Design is influenced by
Exynos5433 clock driver.
Bus clock is enabled by default (in probe function) for all CMUs except
CMU_TOP, the reasoning is as follows. By default if bus clock has no
users its "enable count" value is 0. It might be actually running if
it's already enabled in bootloader, but then in some cases it can be
disabled by mistake. For example, such case was observed when
dw_mci_probe() enabled the bus clock, then failed to do something and
disabled that bus clock on error path. After that, even the attempt to
read the 'clk_summary' file in DebugFS freezed forever, as CMU bus clock
ended up being disabled and it wasn't possible to access CMU registers
anymore.
To avoid such cases, CMU driver must increment the ref count for that
bus clock by running clk_prepare_enable(). There is already existing
'.clk_name' field in struct samsung_cmu_info, exactly for that reason.
It was added in commit 523d3de41f02 ("clk: samsung: exynos5433: Add
support for runtime PM"), with next mentioning in commit message:
> Also for each CMU there is one special parent clock, which has to be
> enabled all the time when any access to CMU registers is being done.
But that clock is actually only enabled in Exynos5433 clock driver right
now. So the same code is added to exynos850_cmu_probe() function,
As was described above, it might be helpful not only for PM reasons, but
also to prevent possible erroneous clock gating on error paths.
Another way to workaround that issue would be to use CLOCK_IS_CRITICAL
flag for corresponding gate clocks. But that might be not very good
design decision, as we might still want to disable that bus clock, e.g.
on PM suspend.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Link: https://lore.kernel.org/r/20211008154352.19519-6-semen.protsenko@linaro.org
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
|
|
Fix the following build/link error by adding a dependency on the CRC32
routines:
ld: drivers/net/usb/lan78xx.o: in function `lan78xx_set_multicast':
lan78xx.c:(.text+0x48cf): undefined reference to `crc32_le'
The actual use of crc32_le() comes indirectly through ether_crc().
Fixes: 55d7de9de6c30 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet device driver")
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for adaptive interrupt coalescing to the dpaa2-eth driver.
First of all, ETHTOOL_COALESCE_USE_ADAPTIVE_RX is defined as a supported
coalesce parameter and the requested state is configured through the
dpio APIs added in the previous patch.
Besides the ethtool API interaction, we keep track of how many bytes and
frames are dequeued per CDAN (Channel Data Availability Notification)
and update the Net DIM instance through the dpaa2_io_update_net_dim()
API.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the generic dynamic interrupt moderation (dim) framework to
implement adaptive interrupt coalescing on Rx. With the per-packet
interrupt scheme, a high interrupt rate has been noted for moderate
traffic flows leading to high CPU utilization.
The dpio driver exports new functions to enable/disable adaptive IRQ
coalescing on a DPIO object, to query the state or to update Net DIM
with a new set of bytes and frames dequeued.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the newly exported dpio driver API to manually configure the IRQ
coalescing parameters requested by the user.
The .get_coalesce() and .set_coalesce() net_device callbacks are
implemented and directly export or setup the rx-usecs on all the
channels configured.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In DPAA2 based SoCs, the IRQ coalesing support per software portal has 2
configurable parameters:
- the IRQ timeout period (QBMAN_CINH_SWP_ITPR): how many 256 QBMAN
cycles need to pass until a dequeue interrupt is asserted.
- the IRQ threshold (QBMAN_CINH_SWP_DQRR_ITR): how many dequeue
responses in the DQRR ring would generate an IRQ.
Add support for setting up and querying these IRQ coalescing related
parameters.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Through the dpio_get_attributes() firmware call the dpio driver has
access to the QBMAN clock frequency. Extend the structure which holds
the firmware's response so that we can have access to this information.
This will be needed in the next patches which also add support for
interrupt coalescing which needs to be configured based on the
frequency.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Johan writes:
USB-serial fixes for 5.15-rc6
Here are some new modem device ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.15-rc6' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial:
USB: serial: qcserial: add EM9191 QDL support
USB: serial: option: add Quectel EC200S-CN module support
USB: serial: option: add prod. id for Quectel EG91
USB: serial: option: add Telit LE910Cx composition 0x1204
|
|
If both dev_set_name() and device_register() failed, then null pointer
dereference occurs in thermal_release() which will use strncmp() to
compare the name.
So fix it by adding dev_set_name() return value check.
Signed-off-by: Yuanzheng Song <songyuanzheng@huawei.com>
Link: https://lore.kernel.org/r/20211015083230.67658-1-songyuanzheng@huawei.com
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
Currently, in case of aead fallback, no associated data info is set in the
fallback request. To fix this, call aead_request_set_ad() to pass the assoclen.
Fixes: 6f03f0e8b6c8 ("crypto: octeontx2 - register with linux crypto framework")
Signed-off-by: Ovidiu Panait <ovidiu.panait@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Extra tab in sev_cmd_buffer_len().
Signed-off-by: Peter Gonda <pgonda@google.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Brijesh Singh <brijesh.singh@amd.com>
Cc: Marc Orr <marcorr@google.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Rientjes <rientjes@google.com>
Cc: John Allen <john.allen@amd.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Marc Orr <marcorr@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Previously, if del_mtd_device() failed with -EBUSY due to a non-zero
usecount, a subsequent call to attempt the deletion again would try to
remove a debugfs directory that had already been removed and panic.
With this change the second call can instead proceed safely.
Fixes: e8e3edb95ce6 ("mtd: create per-device and module-scope debugfs entries")
Signed-off-by: Zev Weiss <zev@bewilderbeest.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211014203953.5424-1-zev@bewilderbeest.net
|
|
This patch adds support for an optional MTD label for mtd2block emulated
MTD devices. Useful when, e.g., testing device images using Qemu.
The following line in /etc/fstab can then be used to mount a file system
regardless if running on an embedded system, or emulated with block2mtd:
mtd:Config /mnt jffs2 noatime,nodiratime 0 0
Kernel command line syntax in the emulated case:
block2mtd.block2mtd=/dev/sda,,Config
Notice the ',,' it is the optional erase_size, which like before this
patch, defaults to PAGE_SIZE when omitted. Hence the strlen() check.
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211009060955.552636-3-troglobit@gmail.com
|
|
Signed-off-by: Joachim Wiberg <troglobit@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211009060955.552636-2-troglobit@gmail.com
|
|
Use of percpu_counter structure to track count of orphaned
sockets is causing problems on modern hosts with 256 cpus
or more.
Stefan Bach reported a serious spinlock contention in real workloads,
that I was able to reproduce with a netfilter rule dropping
incoming FIN packets.
53.56% server [kernel.kallsyms] [k] queued_spin_lock_slowpath
|
---queued_spin_lock_slowpath
|
--53.51%--_raw_spin_lock_irqsave
|
--53.51%--__percpu_counter_sum
tcp_check_oom
|
|--39.03%--__tcp_close
| tcp_close
| inet_release
| inet6_release
| sock_close
| __fput
| ____fput
| task_work_run
| exit_to_usermode_loop
| do_syscall_64
| entry_SYSCALL_64_after_hwframe
| __GI___libc_close
|
--14.48%--tcp_out_of_resources
tcp_write_timeout
tcp_retransmit_timer
tcp_write_timer_handler
tcp_write_timer
call_timer_fn
expire_timers
__run_timers
run_timer_softirq
__softirqentry_text_start
As explained in commit cf86a086a180 ("net/dst: use a smaller percpu_counter
batch for dst entries accounting"), default batch size is too big
for the default value of tcp_max_orphans (262144).
But even if we reduce batch sizes, there would still be cases
where the estimated count of orphans is beyond the limit,
and where tcp_too_many_orphans() has to call the expensive
percpu_counter_sum_positive().
One solution is to use plain per-cpu counters, and have
a timer to periodically refresh this cache.
Updating this cache every 100ms seems about right, tcp pressure
state is not radically changing over shorter periods.
percpu_counter was nice 15 years ago while hosts had less
than 16 cpus, not anymore by current standards.
v2: Fix the build issue for CONFIG_CRYPTO_DEV_CHELSIO_TLS=m,
reported by kernel test robot <lkp@intel.com>
Remove unused socket argument from tcp_too_many_orphans()
Fixes: dd24c00191d5 ("net: Use a percpu_counter for orphan_count")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Stefan Bach <sfb@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/mtd/maps/ixp4xx.c requires MTD_CFI_BE_BYTE_SWAP to be set
in order to compile.
drivers/mtd/maps/ixp4xx.c:57:4: error: #error CONFIG_MTD_CFI_BE_BYTE_SWAP required
This patch avoids the #error output by enforcing the policy in
Kconfig. Not sure if this is the right approach, but it helps doing
randconfig builds.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210927141045.1597593-1-arnd@kernel.org
|
|
Under the following conditions:
* after rounding up by 4 the number of bytes to transfer (this is
related to the controller's internal constraints),
* if this (rounded) amount of data is situated beyond the end of the
device,
* and only in NV-DDR mode,
the Arasan NAND controller timeouts.
This currently can happen in a particular helper used when picking
software ECC algorithms. Let's prevent this situation by refusing to use
the NV-DDR interface with software engines.
Fixes: 4edde6031458 ("mtd: rawnand: arasan: Support NV-DDR interface")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20211008163640.1753821-1-miquel.raynal@bootlin.com
|
|
Add support for the H27UCG8T2ETR-BC MLC NAND. The NAND is used widely
in the NTC CHIP, is an MLC type NAND, and is 8GB in size. Neither
JEDEC nor ONFI detection identifies it correctly, so the ID is added
to the nand_ids.c file. Additionally, per the datasheet this NAND
appears to use the same paired pages scheme as the Toshiba
TC58TEG5DCLTA00 (dist3), so add support for that to enable use in
SLC emulation mode.
Tested on a NTC CHIP the device is able to write to a ubifs formatted
partition, and then have U-Boot (with proposed patches) boot from a
kernel located on that ubifs formatted partition.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210930162402.344-1-macroalpha82@gmail.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: d525914b5bd8 ("mtd: rawnand: xway: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Cc: Jan Hoffmann <jan@3e8.eu>
Cc: Kestrel seventyfour <kestrelseventyfour@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Jan Hoffmann <jan@3e8.eu>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-10-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: b36bf0a0fe5d ("mtd: rawnand: socrates: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-9-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 612e048e6aab ("mtd: rawnand: plat_nand: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-8-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 8fc6f1f042b2 ("mtd: rawnand: pasemi: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-7-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 553508cec2e8 ("mtd: rawnand: orion: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-6-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 6dd09f775b72 ("mtd: rawnand: mpc5121: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-5-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: f6341f6448e0 ("mtd: rawnand: gpio: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-4-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: dbffc8ccdf3a ("mtd: rawnand: au1550: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-3-miquel.raynal@bootlin.com
|
|
Following the introduction of the generic ECC engine infrastructure, it
was necessary to reorganize the code and move the ECC configuration in
the ->attach_chip() hook. Failing to do that properly lead to a first
series of fixes supposed to stabilize the situation. Unfortunately, this
only fixed the use of software ECC engines, preventing any other kind of
engine to be used, including on-die ones.
It is now time to (finally) fix the situation by ensuring that we still
provide a default (eg. software ECC) but will still support different
ECC engines such as on-die ECC engines if properly described in the
device tree.
There are no changes needed on the core side in order to do this, but we
just need to leverage the logic there which allows:
1- a subsystem default (set to Host engines in the raw NAND world)
2- a driver specific default (here set to software ECC engines)
3- any type of engine requested by the user (ie. described in the DT)
As the raw NAND subsystem has not yet been fully converted to the ECC
engine infrastructure, in order to provide a default ECC engine for this
driver we need to set chip->ecc.engine_type *before* calling
nand_scan(). During the initialization step, the core will consider this
entry as the default engine for this driver. This value may of course
be overloaded by the user if the usual DT properties are provided.
Fixes: 59d93473323a ("mtd: rawnand: ams-delta: Move the ECC initialization to ->attach_chip()")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928222258.199726-2-miquel.raynal@bootlin.com
|
|
This reverts commit 56a8d3fd1f342d10ee7b27e9ac0f4d00b5fbb91c.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-9-miquel.raynal@bootlin.com
|
|
This reverts commit c4b7d7c480d607e4f52d310d9d16b194868d0917.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-8-miquel.raynal@bootlin.com
|
|
This reverts commit 3e09c0252501829b14b10f14e1982aaab77d0b80.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-7-miquel.raynal@bootlin.com
|
|
This reverts commit 46fcb57e6b7283533ebf8ba17a6bd30fa88bdc9f.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-6-miquel.raynal@bootlin.com
|
|
This reverts commit 6a4c5ada577467a5f79e06f2c5e69c09983c22fb.
Before the introduction of the ECC framework infrastructure, many
drivers used the ->calculate/correct() Hamming helpers directly. The
point of this framework was to avoid this kind of hackish calls and use a
proper and generic API but it is true that in certain cases, drivers
still need to use these helpers in order to do ECC computations on
behalf of their limited hardware.
Right after the introduction of the ECC engine core introduction, it was
spotted that it was not possible to use the shiny rawnand software ECC
helpers so easily because an ECC engine object should have been
allocated and initialized first. While this works well in most cases,
for these drivers just leveraging the power of a single helper in
conjunction with some pretty old and limited hardware, it did not fit.
The idea back then was to declare intermediate helpers which would make
use of the exported software ECC engine bare functions while keeping the
rawnand layer compatibility. As there was already functions with the
rawnand_sw_hamming_ prefix it was decided to declare new local helpers
for this purpose in each driver needing one.
Besides being far from optimal, this design choice was blamed by Linus
when he pulled the "fixes" pull request [1] so that is why now it is
time to clean this mess up.
The implementation of the rawnand_ecc_sw_* helpers has now been enhanced
to support both cases, when the ECC object is instantiated and when it is
not. This way, we can still use the existing and exported rawnand
helpers while avoiding the need for each driver to declare its own
helper, thus this fix from [2] can now be safely reverted.
[1] https://lore.kernel.org/lkml/CAHk-=wh_ZHF685Fni8V9is17mj=pFisUaZ_0=gq6nbK+ZcyQmg@mail.gmail.com/
[2] https://lore.kernel.org/linux-mtd/20210413161840.345208-1-miquel.raynal@bootlin.com
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20210928221507.199198-5-miquel.raynal@bootlin.com
|
Christophe JAILLET
Colin Ian King
Maciej Fijalkowski
Linus Torvalds
Will McVicker
Ziyang Xuan
Sam Protsenko
Vegard Nossum
Ioana Ciornei
Greg Kroah-Hartman
Yuanzheng Song
Ovidiu Panait
Peter Gonda
Zev Weiss
Joachim Wiberg
Eric Dumazet
Arnd Bergmann
Miquel Raynal
Chris Morgan